Jumbo pumping station 60 35 pc. The dzhileks pumping station will help out a private trader. Rules for choosing pumping equipment

The Gileks pumping station is the brainchild of a Russian manufacturer and his calling card. Reliable and easy-to-repair equipment is becoming a leader in demand. Equally important is the adaptability to domestic conditions and the price. In production, various equipment and materials are used. Of the entire product line, Gilex Jumbo of various capacities is in the greatest demand.

The device and principle of operation of the pumping station

Any pumping station has a basic and auxiliary equipment. The system includes:

• surface pump;
• hydraulic tank;
• automation system.

The equipment in question is capable of pumping muddy water, unlike models from well-known manufacturers. The pump is self-priming, with a built-in ejector, lifts water from a depth of up to 9 m. A filter is also installed on the head. Reinforced engine, automatic switching control, level and pressure control is provided. The Dzhileks pumping station is sealed, the engine is waterproof. Impeller body material:

• stainless steel - "H";
• cast iron - "H";
• glass-filled propylene "P".

The suction pipeline of the pump is lowered into the water layer 30 cm above the lower horizon. A non-return valve is installed on the pump nozzle and the pipe is always under the bay. The pump turns on when there is insufficient pressure in the accumulator. The pressure range is set at the factory. The tank is membrane, two-chamber, counterpressure is created by air. As a result, the Jumbo pumping station provides water supply to several points, depending on the performance.

Advantages of the Gileks station:

• small starting currents;
• no water hammer when the pump is turned on;
• surge protection;
• small mechanical loads;
• dry run exclusion.

The disadvantage is complex installation, and repairs often require a complete disassembly of the pump. A powerful pump with a capacity of 70 l / min is noisy, users recommend soundproofing the room.

Varieties of water supply installations

All stations are distinguished by maximum performance and pressure of the installation. Operating parameters differ from the maximum by 20-30%. This is important to know when choosing equipment.

Let's decipher the marking using the example of one installation - NS Jumbo 60/35 Ch-24:

• NS - pumping station;
• series - Jumbo;
• productivity - 60 l / min
• injection distance 35 m, or into the tank to a height of 3.5 m.
• body - cast iron;
• hydraulic accumulator capacity - 24 liters.

The considered pumping station Dzhileks is popular with summer residents. The installation is economical, consumes 600 watts. Its capacity is enough to provide for a family of 4 people, the cost is about 6 thousand rubles. But water is not enough if you need to organize watering the garden.

The pumping station Dzhileks Jumbo 70 50n 50n is a more powerful installation that meets the needs of a rural farmstead. This model was called Dzhileks DOM. The housing can be made of stainless steel, plastic or cast iron. Users claim that fiberglass is no less durable material. The DOM model is distinguished by a 50-liter battery, increased power - 1100 watts and a powerful controller that ensures the system's performance.

The pumping station Dzhileks Jumbo 50/28 is a baby, ideal for organizing water supply for small families. But a weak pump cannot work for a long period, it is not intended for irrigation. The station costs only 3600 rubles.

The manufacturer provides users with a wide choice. This is basically a variation of Jumbo stations:

• 75 n 5 n,
• 75 n 24 n,
• 70/50 n-50 with a horizontal tank and others.

Difficulties in equipment operation

The system assembled according to all the rules will work reliably. And in order to complete the installation in accordance with the requirements, you need to study the instructions for the Gileks pumping station. Recommendations for connecting equipment will help the competent installation of the station:

1. The intake pipe installed in the water intake should not touch the sand cushion, hang over it at a certain distance. The pipe to the pump rises smoothly, without sagging, in which air can accumulate.
2. The head with an ejector is covered with a sand mesh. A non-return valve is mounted at the top. All joints in the suction line must be sealed.
3. The discharge pipe is connected to the receiver
4. A socket is installed, always with grounding.

Automation devices are configured at the factory stand, if necessary, it is better to contact specialists to change the parameters.

The instruction manual for the Gileks pumping station describes the main malfunctions and how to eliminate them.

If the pump is running and no water is coming in, the cause is air getting into the suction system. It is necessary to check if the check valve is leaking and if there is water in the well. Often air sucks in through leaks in the joints.

If water enters the system in jerks, the pump often turns on, the membrane may have broken or the relay has failed. Due to a relay malfunction, the pump may not turn off at all.

If it does not turn on, check the serviceability of the outlet, the presence of energy in the network. In the instructions for the Gileks pumping station, you can find the answer to many questions. It also describes self-repair and recommendations to contact the nearest service center.

Spare parts for Gileks pumping stations are not difficult to find. And their cost is not high. If repairs are made in the workshop, taking into account the complexity, they will take 500-600 rubles for the work. But spare parts must be purchased separately. A battery tank can cost from 900 rubles, a membrane - 400, and a pressure switch above 600. All nodes are sold in specialized stores or repair shops.

Jumbo 60/35 P-24 is an automatic water-lifting unit based on a self-priming electric pump.

Description
Jumbo 60/35 P-24 is a pumping station - "automatic pump" - with a built-in ejector. The system automatically turns on and off as consumers consume water, maintaining the required pressure in the water supply system.

Design
The pumping station is equipped with a surface self-priming electric pump, a horizontal hydraulic accumulator with a capacity of 24 liters, a pressure switch, a pressure gauge, connecting fittings and an electric cord with a plug.
The pump consists of two main parts - the pump part and the electric motor, which are mounted on the adapter flange.
The pump housing is made of glass-filled polypropylene with embedded brass threaded parts, and the impeller and flow block are made of wear-resistant plastic materials.
The aluminum adapter flange on the pump side is separated from contact with water by a plastic cover.
Graphite-ceramic self-priming mechanical seals prevent the possibility of external leakage from the pump part.
An asynchronous squirrel-cage motor includes a stator, end shields, a squirrel-cage rotor and a terminal box.
The motor stator is protected by a thermal protector and is cooled by a fan.

Distinctive features

• automatic pressure control
• built-in internal ejector
• uninterrupted water supply
• motor protection
• wear-resistant materials
• long service life
• modern design

Advantages
The pumping station combines the practicality of self-priming pumps with the advantages of centrifugal pumps, which creates optimal suction conditions at the pump inlet and high outlet pressure. As a result, the requirements for the purity of the pumped water and the presence of dissolved gases in it are reduced.

Mounting
All electrical work (installation of the socket, connection to the power supply, grounding, etc.) must be carried out by a specialist in accordance with safety regulations.
The installation procedure consists of several steps. First, a suction pipe with a check valve is connected to the inlet, and a pressure line is connected to the outlet. Then the pump housing and the suction line are filled with water, the voltage (220 V) is checked, after which the pump is connected to the mains.
Installation of the suction line requires a continuous angle of inclination from the pump to the water intake source (at least 1° to the horizon).
! Air must not enter the suction line.

Application
Automatic pump Jumbo 60/35 P-24 is used in private houses, country cottages, cottages and other residential premises for uninterrupted water supply with automatic maintenance of the required pressure in the system.

Note
Operation of the pump with an automatic pressure control system without water is strictly prohibited!

Recommendations
The pump must be protected from direct sunlight and not placed near heating appliances.
Before a long period, it is simply necessary to drain the remaining water from the pump, rinse with clean water and dry.
Periodically it is necessary to check the maximum pressure and energy consumption of the pump to avoid an emergency.

Quality assurance
The Jumbo pumping station has high performance, unpretentiousness to the purity of the pumped water and resistance to voltage fluctuations in the mains, which confirms its high-quality and reliable operation throughout its long service life.

Operating restrictions

• admissible concentration of firm particles in the pumped-over water – 150 g/m 3
• the maximum number of pump starts is 20 times per hour
• maximum size of solids in pumped water - 0.8 mm
• allowable temperature range of pumped water – from +1°С to +50°С
• maximum suction depth - 9 m

Flow-pressure characteristics of the pump

The range of products manufactured by GILEX includes several models of borehole pumps with different technical characteristics. This equipment is intended for use as part of domestic and industrial water supply systems with water intake from wells and wells. According to users, well pumps from JILEKS LLC are among the best on the Russian market.

Rules for choosing pumping equipment

The efficiency of an autonomous water supply system with forced water supply depends on the compliance of the technical characteristics of the pumping unit used with the conditions of water use. To do this, it is necessary to make a thorough analysis of all the nuances of the upcoming operation even before ordering the equipment. If you are faced with the question of which well pump is better to choose, consider the following criteria:

• well flow rate and volume of water consumption, the maximum number of inclusions per hour;
• temperature of the pumped liquid;
• parameters of the existing electrical network;
• water quality, presence and size of mechanical impurities;
• possible immersion depth for the submersible unit.

One of the most popular borehole pumps of the JILEKS company is the VODOMET centrifugal submersible unit. This equipment is available in several modifications, which allows you to choose a device with optimal technical characteristics for specific conditions of use. Each model is distinguished by high reliability, unpretentiousness, efficiency, and has a high efficiency. When choosing, use the online consultation of our company's specialists. Channels for communication are given in the "Contacts" section.

Surface automatic pumps of the Jumbo series

JAMBO 60/35 P-K- a popular brand of centrifugal pumps from a Russian company Gilex. The pump, which can lift water from a depth of 9 meters and has a capacity of 60 l / min, operates with a low level of noise and is not subject to corrosion. In combination with the automation unit and the hydraulic tank included in the kit, it allows this equipment to work as a small pumping station.

Features of the automatic pump of the JAMBO series:

• Automatic pump serves to maintain the required pressure in the system;
• A wide range of models allows you to optimally select equipment for operating conditions;
• Surface mounted - not submersible;
• Designed for clean water supply systems;
• The design of the pump allows you to raise water from a depth of up to 9 meters;
• The automatic pump has an automatic flow control system;
• The centrifugal pump body is made of plastic, the impeller is made of wear-resistant plastic materials;
• Reliable mechanical seals protect the pump from external leaks;
• The asynchronous type electric motor has a built-in fan for cooling, the starter is protected by a thermal protector.

Automatic pumps manufactured by the company Gilex, differ in the way of control - this model, which is implemented on the basis of a centrifugal surface pump of the series Jumbo with the index "K" has a control device that controls the magnitude and presence of the flow. In addition to the flow, the automation controls the pressure, and when it decreases, it turns on the pump. An automatic pump with a device that controls the presence of a flow also has a hydraulic tank that accumulates water and smooths out sudden pressure fluctuations. A water supply system with an automatic pump is an ideal solution for country houses, for which water is taken from a well.

If you are a client of the Garden Mechanisms online store, then you can use the service of a qualified pre-sale preparation of equipment. It is implemented on the basis of its own Service Center, which has authorization and certificates from the world's leading manufacturers.

How the equipment starts in operating mode depends on its further operation. In our case, an experienced employee of the Service Center will perform a test run at idle. Especially for our customers, we will adjust and set up the equipment in such a way that it is ready for the upcoming loads. After that, if the results of the check do not cause claims, the instrument is sent to its rightful owner.

What are we doing?

• checking the complete set (when opening, it is checked whether everything is in place)
• assembly of the finished product (if necessary)
• adjustment check
• oil filling equipment
• lubrication control in gearboxes and gearboxes
• product launch

Everything for the Client

• As soon as the tool is unpacked for pre-sale preparation, a professional works with it. Therefore, we can guarantee the quality of our services.
• You get equipment 100% ready for work.
• Competently executed commissioning is excellent results in the future.

Important

When making a purchase of a petrol tool, the managers of the Garden Mechanisms online store offer everyone the service of pre-sale preparation. You can opt out of this service if you wish.

In what cases do they refuse pre-sale preparation?

• If you wish, you can receive the product in its original packaging and open / assemble it yourself.
• If the product is planned as a gift and traces of equipment operation are undesirable (fuel residues in the tank, filled oil, opened packaging).
• In the event that its further transportation is expected, which is impossible with the assembled product. For example, it is supposed to send the goods through a transport company or by mail, or further transportation is planned by transport, where the assembled product does not fit in size.

Pre-sale preparation cost

The price includes: unpacking and checking the complete set (when opening, it is checked whether everything is in place), assembly of the finished product (if necessary), checking adjustments, refueling equipment with oil, refueling, lubrication control in gearboxes and gearboxes, starting the product. Oils and lubricants are not included in the cost of assembling the equipment.

Gasoline is poured minimum amount. The approximate cost of assembly of the product can be found in the table. The cost depends on the complexity of the assembly and the time spent on it. Specify the conditions, terms and the exact amount of assembly / pre-sale preparation with the manager when placing an order. Free pre-sales training applies only to all products of brands and. The products of these manufacturers are marked with a special “Free presale” badge.

Installation and assembly of additional attachments for tractors and walk-behind tractors is paid separately and the cost depends on the type of equipment and the complexity of the work. Specify terms and cost of this service at managers.