Heating boiler de dietrich. Floor boilers DE DIETRICH. Technical characteristics of EF series boilers

I have a single-circuit boiler De Dietrich MSL 31 with an indirect heating boiler. Before the summer, I switched it to hot water mode, but found the following. The unit is in the basement. Above it, on top, there is a comb of a warm floor on the first floor and a heated towel rail on the first floor. On the comb is a pump for underfloor heating. I turned off the pump on the comb, as I turned off the heating. For some reason, at the same time, the heated towel rail became hot, as if by the temperature of the water in the boiler. Can the boiler in hot water mode give some volume of water to the heating system? And since the towel warmer has the smallest circuit, then, as I assume, this volume goes into it, and therefore it is hot. Now I specially turned on the heating again, and that's it, the heated towel rail has cooled down, since I turned on the pump for the warm floor and the pump for the return.

Check the piping diagram of the boiler, water heater, connection of the underfloor heating. Check the presence of a check valve in the circuit, which is heated in summer operation.

Malfunction of the De Dietrich DTG N 38 M gas boiler. The problem is that it does not reach the maximum set temperature. It stops at 45 degrees and then cycles. What could be the problem?

Check the boiler thermostat, draft sensor, chimney.

Double-circuit boiler 24 kW three years in operation. Everything is fine, the electrodes are clean. Periodically, it cannot start and gives an error e99. Who faced and what to do? Maybe some advice. Or just a replacement fee?

Fault code E98/ E99 - Internal error of the electronic board - Replace the electronic board.

In the country house there is a De Dietrich dtg x 42 n floor standing gas boiler, now it is in winter mode. In operation for 5 - 7 years, in the summer the master came and supposedly cleaned it. It all started towards the end of the summer, the device worked, then turned off, the 4-amp fuse bounced. The master said not to pay attention to the fuse, he pressed the button on it back and that's it. The problem is that I set the temperature of the batteries on the boiler to 9, and they heat up to 2 maximum. The unit heats the boiler, water and floors well, and the batteries are 10 degrees. In the batteries, I know, some kind of non-freezing liquid is filled. The device heats up to 80-90 degrees, even if the value is set, for example, 4. According to the sounds of operation, everything is in order. Yesterday the master changed some kind of pump - it did not bring any result.

You need to contact the ASC, drain the incomprehensible liquid from the system, rinse and fill with water. After that, check all electrical connections for pumps, water heater, floors and the MB2 module, if present.

De Dietrich ms 24 mi ff. Stopped running, no errors. The flow of water sees. If you restart, it works out 1 heating cycle and stands on the purge. Does not respond to water supply. I checked the parameters, everything is fine. In the info menu, the voltage on the modulator is 0%. What is your verdict? The unit has been in operation for 5 years. 2 years ago they repaired the board after a thunderstorm. The fan turns off after a couple of minutes. The circulation pump continues to run.

The hot water temperature sensor is damaged, without giving errors. We put another sensor, and everything works.

Boiler WHE 2.24 FF. Worked the first week after summer. Turned off for a day, because. it got very warm outside. I turn it on in the evening. And after the test, it turns on for heating for 5 seconds, then blinks all the diodes, and blocks. All lamps are lit except for the No Flame Indicator or Thermostat Open. I emphasize that they do not blink, they are all on fire. The same is true with the start of the DHW. All the same. And even without heating, hot water does not turn on. After several resets, the heating worked. But as soon as you open the water of the DHW circuit, something clicks, all the lamps also flash, and then blocking. And these three lamps are lit again. Tell me, please, what is it?

It looks like protection from a short cycle of work. Check the pump, water pressure in the system, expansion tank.

De Dietrich GT 225 boiler. M200/1 S burner, liquid fuel, DIEMATIC 3 control panel with outdoor temperature sensor. Arriving home, I found the burner in the blockage (the button on the burner is on), when pressed, the button went out, but the burner did not show any signs of life. Turning the unit off/on didn't work. There are no errors on the panel, green lights on the burner and panel. The burner does not start, does not respond to button presses. How to start the burner? The burner symbol was on in the display. The thermostat was not blocked. The burner did not lock out. Interestingly, no alarms. There is a green light on the burner, on the control panel there is an indication of the burner operation, only the burner is not lit. The problem disappeared by itself as suddenly as it appeared.

It would be good to check the status of the jumper at the CS input. If any safety device is installed instead (water pressure switch, etc.), then check it.

Installed wall-mounted boiler De Dietrich ms 24mi ff. When hot water is turned on, it produces very hot water, although the temperature is set to at least 35 degrees. What could be the reason? Sensor defective?

It is possible that the consumption of heated water (cold, which is heated to hot) is very small. In this case, the unit operates at minimum power and heats up already to that temperature. Try increasing your water flow.

Tell me, please, how to independently search for the De Dietrich MS 24 MI FF gas boiler assembly that has failed? It is connected to the mains without any additional network filters or stabilizers. In the morning, after a thunderstorm, the unit was not in working condition. Does not turn on. There is voltage, the fuses are intact. Because with a high degree of probability, the problem is related to a thunderstorm, i.e. voltage drop
Guarantee for this situation, I think, will not apply. What is the probability that the problem is not in the main board? How can I check or make sure that the board is a replacement? What are the recommendations for protection for the future from thunderstorms and power surges?

First of all, you need to replace the board and check the operation of the boiler. For the future - put surge protection and a stabilizer.

Ignition constantly clicks, but the main burner does not turn on. What could be the reason? And the second question I am very interested in is why the DTG 138 boiler does not go into an error-blocking state and does not display any errors on the remote controls? I found him in this state quite by accident, and it seems that he just turned on and off the ignition for many hours. Is it normal?

It is necessary to replace the programming unit (ignition unit) SIT, which is installed on the gas valve. It is he who is responsible for the correct ignition of the burner.

Help troubleshoot. The ignition error was on the mca 45 boiler. Hot water does not flow. It rained heavily last night, maybe that had something to do with it? We operate the unit for 2.5 years. What to do to make it work? Even after the reboot, I began to write "remove the air, m20".

M20 is the bleed cycle. After that, the device should start.

A De Dietrich MCA 35 gas boiler was installed. Sometimes an L36 error popped up and it stopped, after restarting it turned on. When such errors became more frequent, the master was called and set up the gas block (not counting the annual service). But over time, such errors have become more frequent. In February of this year, the gas block was replaced with a new one, but this only helped for two months. Further, the situation became even worse. At the moment, the master has set up the gas block, and when the front (facade) cover is closed, the settings go away, and the unit starts to stop again, (I want to say right away that the device is located in a room about 40 meters with 5 windows, the ventilation is working and cleaned) . Can you tell me what could be the reason for this phenomenon?

Most likely, the ignition electrode and/or the ignition transformer needs to be replaced.

De Dietrich, atmospheric gas, DTG X 42 N, AD230. RX77S module. AD239. Room temperature sensor CTI-S-03 with regulation. The room temperature sensor, according to the passport, produces a decrease in the graph by changing the resistance. Where then should the GSM module connector be connected to control the boiler? In all GSM modules, I found only relay outputs, and none of them has an analogue of CTI-S-03. Maybe there is a feature when assembling the chain?

Is there such a need to remotely turn the unit on and off? If yes, then in this case we use the relay output of the GSM device and the CS input of the boiler, having previously removed the jumper from it. The GSM device must have its own room temperature sensor.

After the summer period, the DTG boiler was turned on (in operation for 5 years). Glow plug lit, no gas flow. The spark plug was changed, the burner does not ignite, the emergency button on the ignition control unit lights up. Rebooted a few times and the burner still won't ignite. The ignition control unit was changed, the glow plug burns, the burner does not light up. What else needs to be checked in order for the gas supply to the burner to go?

Check the correct phasing when connecting the power supply to the machine.

Tell me, please, what automation needs to be installed - Two mounted Zena Plus boilers of 31 kW each, work on a comb with 3 mixing circuits and a boiler. Their work must be ensured in a cascade mode according to a weather-dependent scheme. I can't figure out which is better?

You can install 2 Diematic VM iSystem modules and control the cascade (parallel operation of boilers) and heating circuits from them.

Very often, for the last 3 days, error E03 has been constantly lit, the unit does not start. If you open the window, it turns on. During the day, of course, this can be done, but at night the problem is that it is cold to leave the window open. Advise what to do? The chimney has been cleaned, there is draft.

Ensure proper supply ventilation to supply combustion air to the appliance.

There is a wall-mounted boiler De Dietrich MS 24 MI FF. I purchased a UPS for backup power: online, pure sine. If the UPS is turned on in inverter mode (220V mains off, battery powered), the device will go into error E01. As far as I understood, reading about phase dependence, this is a normal reaction of the unit to such a connection scheme. Is it so?

Strange behavior for the UPS - when the power is turned off, it does not provide backup power. If pulled out of the socket, then we lose the working zero and protective ground, relative to which the device measures the ionization current (signal of the presence of a flame). It turns out that it is not necessary to pull out of the socket.

Installed wall-mounted boiler De Dietrich MSL 24 FF. I wonder if there is a minimum gas pressure switch in his device? How will the device in the basic configuration react to the interruption of the main natural gas supply with the subsequent restoration of the supply?

This model does not have a minimum gas pressure switch. If the gas disappears during the operation of the burner, the unit will report error E01 - loss of flame. You will need to manually reset this error.

De Dietrich MS 24 MI FF. When you fill the system, water constantly drips from the disconnector, and the pressure in the expander drops. What is the reason?

Alternatively, low cold water pressure - the 2nd non-return valve in the disconnector does not open; the disconnector itself is faulty or there is dirt in it. Drain the water, disassemble the disconnector, clean it.

We recently installed a De Dietrich MS 24 MI FF gas boiler and the system was changed. Today, the electricity was turned off during the day, I came home from work, the unit does not work, it gives an E10 error. Turned off the faucet as instructed and it worked. I turned off the faucet, though not immediately. Now the device is working, but water is dripping from it. The pressure shows approximately 2.5. What to do?

The pressure needs to be reduced. In this case, you should contact the experts.

Boiler MS 24 FF. Everything works, but I don’t want to adjust the temperature on it every day. What can be done so that it finally stops turning on / off every 5-10 minutes. Tell me what will change when connecting an outdoor temperature sensor and a room thermostat (despite the fact that there are radiator thermostats and thermostats for controlling the supply of underfloor heating circuits). If the floor heating air thermostat is
for example, +23 degrees, and on the remote thermostat of the boiler +20 - then the unit will never heat up to +23, right? And if you put +26 on it, then it will never turn off at all until the thermal protection turns off? And on the second floor, radiators with thermostats live their own lives. How will all this interact?

The room thermostat of the unit must be installed in the coldest room on the 2nd floor, open there to the full thermostatic head of the radiator. Set the required +20 C on the thermostat. Set a slightly elevated temperature on the underfloor heating mixture - 40-45 C. Set the desired temperature on the underfloor heating thermostats. Start the unit. According to the temperature schedule, select the closest schedule for heating.

We have error E01. The boiler, after pressing the R button, starts up, the sound of a start-up spark is heard, the gas is supplied, but after 5 seconds everything goes out and E01 and the no-flame icon are displayed. All this began to happen after the stabilizer suddenly burned out. I think we have a very unstable voltage. Tell me, the unit can generally work without a stabilizer?

De Dietrich - phase dependent, i.e. the phase must be exactly where the device is waiting for it. If you swap places, it will be like you spark, but do not ignite and then issue E01. Apparently your stabilizer reversed the phase and zero.

The Ms 24 mi FF boiler worked for exactly a month (so far only heating) without any problems, then it constantly gives error E01. The flame lights up, burns for a few seconds, then a quiet click is heard, the flame goes out and E01 appears.

E01 - Ignition error or gas supply error. To reset - Hold down the R key for 2 seconds. Check that the gas supply is ensured and that the gas line has been purged of air. Check the phasing phase-zero 230V and zero-ground 0 V. (Turn the plug in the socket). Check the fuses on the control panel. Replace if necessary. Check if there is a room temperature thermostat. If there is no room thermostat: check the presence of a jumper on the terminal block. Check the absence of voltage between zero and ground (less than 5 V). (Check for the presence of a dielectric insert after the gas valve on the downstream). Check the ionisation/ignition electrode: Position. Visual inspection (worn condition). Electrode cables. Check the gas pressure at the burner during ignition.

DTG-130 with Diematic 3 does not attempt ignition. When it is started, the pumps turn on, the burner symbol lights up on the display, no errors are shown. But the burner does not turn on, there are no attempts to ignite.

Check the safety thermostat, unlock it. Check the presence of a jumper on the CS connector. If safety automation devices were connected instead of a jumper, then check them.

Question about the recirculation of boilers in the cascade. Should the slave unit's pump be displayed on the master m3's panel? Recirculation pumps are connected to the terminals of each device, respectively. Pumps between them and the hydraulic separator - is that correct? Or is it more correct to connect these two pumps simply to machines?

The circulation pumps of the boilers must be connected to the appropriate connectors on the control panel. The slave pump is not displayed on the master control panel.

Boiler Dietrich MS 24 MI FF. Periodically gives error E05 and stops. Later it can start itself, or it starts working only after numerous on-off switches. It has been in operation for two months, such problems appeared two weeks ago and occur every three days.

Heating or DHW sensor error. They need to be checked.

The MS 24 MI FF boiler cannot start a couple of times a day, gives an E35 error, after pressing the R key it starts up normally. What could be the reason? When working in the summer mode, everything was fine.

Boiler 24 bic/ll ff gn suddenly turned off and displayed an overheating error. As soon as it cools, it starts for a few seconds and again in an error. Maybe the pump burned out?

Check the overheat sensor. It might be open all the time. Another option is the 3-way valve does not switch. The pump can be removed and checked. Check all flat seal pump connections. Heat exchanger - disconnect and check for dirt and blockage.

About once every 2 days, the RMS-M 24 boiler turns off and error E36 is displayed. After pressing the "reset" button, it restarts and continues to work normally for another 1.5 - 2 days. Then everything repeats. This began to happen after turning on the heating of hot water (boiler). What could it be and how to fix it?

Flame loss occurred more than 5 times. No ionization current. Remove air from the gas pipeline. Make sure the gas cock is open. Check gas supply pressure. Check the operation and setting of the gas valve block. Make sure that the air supply pipes and the flue gas outlet are not blocked. Ensure that combustion products are not re-sucked in

Tell me, please, about the pumps and their modes of operation, the necessary settings in the following boilers: MS 24 MI FF double-circuit. MS 24 FF single circuit. MSL 24 FF single circuit. Now I use a double-circuit, one of the circuits of which is connected to a warm floor, the circuit is small, about 5 square meters. In what mode will it be necessary to put the pump at the end of the heating season, i.e. the radiator circuit will need to be turned off, but I want to leave the TP circuit. I plan to put a single-circuit boiler and an indirect heating boiler in the house under construction. I would like to know the main differences between the models, in particular, how pumps differ in power and control capabilities. By electricity consumption. How do pumps react to a partial blockage of the flow through the radiators by thermal heads, i.e. water consumption is reduced. What models of pumps are installed in these modifications? And are they the same on MS and MSL models?

After disconnecting the radiator circuit, turn the pump to a lower speed. The boilers MS 24 FF and MSL 24 FF are equipped with two-speed pumps. The unit has a built-in bypass through which the heating circuit water will pass in case of partial or complete shutdown of the heating circuit. The pumps in MS and MSL boilers are different, but the characteristics are a bit similar.

The De Dietrich DTG X boiler has been in operation since 2011. From the very beginning there was a difference of 7-10 degrees between the temperature shown by the unit and the thermometer on the manifold. Now the difference has reached 20 degrees. I checked with another thermometer - it is the sensor on the boiler that is lying. Cleaning the thermocouple sleeves did not help. Can the sensor be calibrated? Or is the sensor not the problem?

Install another thermometer exactly in the sleeve of the device. If it also shows a higher temperature, then the point is not in the sensor, but in insufficient water circulation through the extreme right sections. At a minimum, the heat exchanger will need to be flushed.

Please tell me where to look. Boiler dtg 130. Yesterday, suddenly, it stopped lighting the main burner. The auxiliary burns, while he cannot determine that it is burning and constantly tries to light it. Accordingly, the main burner does not light up.

You need to check the phasing.

To date, the De Dietrich gas boiler is the product of the vast experience and professional work of the French company's specialists. For this reason, these low-temperature gas appliances and liquid fuel equipment have long gained a reputation all over the world. As practice shows, they are popular among users.

Pay special attention to the fact that the De Dietrich gas boiler is of excellent quality, very economical, efficient and easy to install and transport. Not many people know that a distinctive feature of devices is the ability to select parts. When ordering the device, you can always make an additional order of parts and select the necessary control panel.

The De Dietrich condensing boiler has a conventional control panel, which is distinguished by the letter “B”, but there is also a modified control panel called Diematic 3. This panel differs from the usual possibility of special programming and influencing the combustion device to automatically change the temperature of the unit. When you pick up such a panel, you will immediately have the ability to remotely control the unit.

Rice. one

Also, an important advantage lies in the fact that the De Dietrich gas boiler is equipped with a special system for removing combustion products using natural exhaust gases. The manufacturer always cares about the quality of the products. All customers are provided with free after-sales service, high-quality components and quality control of the device.

You can always view all models, as well as the De Dietrich gas boiler, in the product catalog section, which is posted on the site.

Gas boiler. Description. Manufacturer. Gas boiler De Dietrich

Today, the manufacturer is one of the leading companies in heating technology. We can safely say that this is number one in the direction of the company's development. The main priorities of this company are environmental protection, significant energy savings and uninterrupted operation. For example, in France and abroad, De Dietrich Thermique employs more than two thousand people.

The company earns approximately four hundred million euros per year. Eleven years ago, an industrial group was created that wanted to take first place among the five largest manufacturers of heating equipment. For six years now, the company has been part of the BDR Thermea holding, which is a global manufacturer and supplier of new heating and hot water systems.

It should be noted that this company serves more than sixty countries. Annual sales amounted to thirty thousand low-temperature gas or fuel, as well as solid fuel boilers and 2-3 condensing units.

Rice. 2

Condensing boiler De Dietrich. Main technical characteristics:

• Boiler De Dietrich heated room size - 320 m3;
• Gas boiler De Dietrich power consumption - 36 kW;
• Boiler De Dietrich connection - 220-230V Hz;
• Boiler De Dietrich required gas flow - 4.22 m3;
• De Dietrich boiler required chimney diameter - 150 mm;
• Boiler size (H-W-D) - 850-596-707 mm;
• Weight - 131 kg;
• The volume of the water heater is 130 liters;
• Used power of the heat exchanger - 23 kW;
• De Dietrich gas boiler, its productivity in hours is 565 liters per hour;
• Productivity - 210 liters in 10 minutes;
• The gas boiler De Dietrich has a specific capacity of 20.5 liters per minute;
• Heat loss - 68 W.

Condensing boiler De Dietrich. outdoor use

The De Dietrich boiler is a low-temperature floor-mounted device, which is made of cast iron, a common material, it has a built-in atmospheric gas burner. The boiler emits a small amount of harmful substances into the atmosphere and ignites automatically.

This boiler is mainly used to operate on gas, but if retrofitting equipment is installed, the gas unit can also operate on propane. The De Dietrich gas boiler is designed specifically for severe frosts and meets all the requirements for supplying hot water and central heating.

Main control panel

The main electromechanical control panel contains the main functions. The main thing is an on and off switch, a special switch (for winter, for summer, as well as a protective thermostat test), a thermostat switch from thirty to seventy degrees, a thermometer switch, a fuse. There is also space for a module if there is a need for hot service water for sanitary purposes.

What gives the device

• The gas apparatus has a high efficiency;
• Reinforced thermal insulation;
• The gas apparatus has an ignition of the boiler from electricity;
• The gas unit is equipped with an electrical and mechanical control panel;
• The gas unit has a magnesium anode that protects the equipment;
• The gas apparatus emits a minimum amount of harmful substances;
• You can always install a water heater next to your boiler.

Boiler advantages:

• The gas boiler has reinforced thermal insulation (this significantly reduces heat consumption to the environment);
• You can always install it next to the water heating equipment, but it is not included in the main kit. The gas unit can fully provide hot water for maximum comfort.

Additional items:

• Main water heater GMT 130 B;
• Room temperature thermostat (it can be software, simple, or one that is programmed without using wires);
• DHW module MV2;
• Equipment for switching to H gas;
• Set of equipment for switching to gas L;
• Special equipment for switching to work with a pressure of 13 mbar;
• Special equipment for conversion to propane G31.

Purpose of equipment

A De Dietrich condensing boiler with a built-in atmospheric gas burner is most often used for heating (if you install a water heating element, then you can use hot water) at home, cottages, cottages, as well as other residential premises in the private sector.

Rice. 3

Before buying, you must remember that this equipment has operating restrictions (maximum operating temperature - 90 degrees, maximum operating pressure - 4 bar).

Gas condensing boiler. Technology advantage

The De Dietrich boiler can operate on both propane and natural gas. The equipment of this series combines the main advantages of condensation technology with the compactness of wall-mounted units. If you use the heat of water vapor, which is contained in flue gases, then condensation heats more space with minimal energy consumption.

Also, the main advantages of this equipment include the elegant design of the unit, simple use and very high technical characteristics. For example, such as increased average annual efficiency up to one hundred and ten percent, low emissions of harmful substances and low noise levels. If your room is small, then this is not a problem, since the minimum dimensions of only five hundred millimeters allow you to install it anywhere.

Additional features

These appliances are very easy to use, light, compact, silent in operation and can always be connected to a coaxial chimney. We can safely say that the De Dietrich condensing boiler will find its application everywhere. They are used for hot water boilers with a closed system and with a maximum operating temperature of ninety degrees. Professionals recommend installing for temperature heating installations.

De Dietrich boiler. Basic technical requirements

The De Dietrich condensing boiler is a heating device that fully complies with all established rules and regulations. It has the latest, compact, fast exchanger, which is made of an alloy of aluminum and silicon metal. The burner in the unit is made of steel that withstands corrosion, and the operating modulation range is from twenty-four to one hundred percent of the power, with minimal NOx and CO emissions. There is a special silencer that provides air flow for combustion.

Rice. four

The control panel can be removed, but you can always attach it to the wall. The factory set includes a control panel that can control the DHW circuit and the heating circuit (additional equipment - sensor for the DHW cylinder). The De Dietrich gas boiler will be delivered to your home assembled.

Components of the De Dietrich condensing boiler: supply pump - 1 pc., tank volume of which is 8 liters, automatic air vent, 3 bar safety valve, heat exchanger, it is plastic for devices whose model is PMC-M ... MI, air connectors / flues Ø 60/100 mm with measuring tap, PMC-M + BMR/SR.

There is a special kit for connecting a water heater / gas appliance and a DHW sensor, but it must be ordered as an additional equipment. Very important elements PMC-M ... MI, which come with a plastic heat exchanger for domestic hot water. It is this equipment that provides hot water. It should also be noted that a limiter is installed in all models, which calculates the flow rate.

Equipment characteristics

• The De Dietrich boiler is durable and reliable;
• All models have built-in atmospheric gas burners. These burners are made of special stainless steel, which allows for thermal insulation of the De Dietrich gas boiler and significantly reduces the loss of precious heat;
• The gas block is equipped with a special software element that fully controls and ensures the ignition sequence, as well as the operation and extinguishing of the gas burner;
• The flue gas circuit is a design that provides a natural stop and draft of the appliance;
• Built-in draft sensor fully protects against leakage of flue gases;
• You can always install a DHW tank next to your unit (it is not included in the scope of delivery, but it can be ordered separately). All this makes it possible to fully ensure the supply of hot water and thereby achieve the maximum level of comfort.

De Dietrich boiler. Device

The De Dietrich condensing boiler has two panels that can be installed to choose from:

• Diematic iSystem. This panel is designed for direct and complete control of the machine, which is connected to the main mixer. This system has an intelligent processor that regulates the operation of the entire boiler plant. The inner panel is equipped with new ergonomics for convenient and fast programming, this can be done by replacing all the buttons with one main rotary knob).
• IniControl. This panel is used to solve simple tasks or to change an existing system, for example, the LCD display is used to change the parameters of the machine).

The panel called (Diematic iSystem) is necessary for weather changes, and it can also be used to adjust the heating circuit depending on the outside temperature. It is necessary to draw your attention to the fact that the number of circuits may vary depending on the other equipment switched on, the maximum number is three heating circuits. In addition, this panel provides access to all cascade installations from two to ten units.

The De Dietrich condensing boiler must be fitted with a Diematic iSystem or IniControl panel. Now the panel is a device with ergonomic control. It has a weather-dependent electronic control system that can influence the burner: the temperature of the water in the appliance is maintained automatically and can be at room temperature only if additional equipment is connected.

It can be CDR D. And System, CDI D. And System module, a remote control unit with a room temperature indicator, or the water temperature sensor itself. The initial kit includes a panel called Diamatic System, which can regulate the operation of turning on and off the main heating with a direct circuit on the machine without the use of valves.

Equipment installation

The condensing boiler De Dietrich can be installed alone or in cascade capable of:

• Placed on the wall for up to seven devices;
• Placed on the floor in one row up to seven devices;
• And also it can be installed back to back ten minimum or five plus five.

The gas wall-mounted condensing boiler produces heating using registers or underfloor heating, and also supplies hot water using storage water heaters (they can be integrated or connected) or using a robust heat exchanger that provides water flow.

The wall-mounted condensing boiler De Dietrich is used both in new and renovated areas, for heating large houses, apartments, country cottages.

What is a De Dietrich gas condensing boiler? Saving. Guarantee

Remember that the De Dietrich condensing boiler fully complies with all the most current requirements: environmentally friendly, economical, convenient and comfortable. The De Dietrich condensing boiler generates gases that contain large amounts of water vapor, which then cool down as they pass through the heat exchanger. The steam then condenses and its latent heat is gradually added to the calorific value. It turns out that the efficiency is achieved above one hundred percent and thus there is a strong savings.

The range of boilers, both wall-mounted and floor-standing, of different capacities:

• Wall gas apparatus Innovens mca;
• Wall gas apparatus mcr-p;
• Gas apparatus for wall s230/330/630;
• Gas unit for wall naneo pmc-m.

De Dietrich is one of the oldest brands producing luxury home appliances. It was founded at the end of the 17th century in France and continues to develop successfully, uniting a whole group of companies.

Prestigious brand products

De Dietrich household appliances are produced at 19 factories in six countries, including France and Italy. All products belong to the premium class, are presented in 20 countries and are in very high demand. Many types of equipment have been awarded prestigious awards for the use of innovative technologies, integrated design, unique design and the introduction of other original ideas.

The ovens of this manufacturer were equipped with a touch control system back in the early 2000s. And in 2005, a unique low-temperature cooking program was introduced. All ovens offered by this brand are distinguished by their versatility and modern appearance. They have color displays and user-friendly control panels. Hobs have an aesthetic design and the largest cooking areas. Induction hobs have received an award for integrated design approaches. Hoods are equipped with intelligent control systems, and dishwashers are equipped with innovative designs.

The De Dietrich range is progressive equipment that allows you to implement a variety of processes in the kitchen. The company produces:

• . refrigerators;
• electric ovens and microwave ovens;
• hobs of various types;
• dishwashers;
• hoods, coffee machines, steamers, grills, deep fryers and other appliances.

All products have a perfect appearance, corresponding to modern ideas about the beauty of household appliances. Among the main advantages - perfect quality. The company holds leadership in the world market in terms of the number of innovations introduced.

Refrigerators and hobs, ovens and dishwashers from this manufacturer practically do not fail. In each country where the brand's products are presented, there are specialized service centers that restore the functionality of equipment in the shortest possible time.

Selection of household appliances in the Hausdorf store

In the De Dietrich model range, potential users can choose equipment that meets a whole range of preferences. In the Hausdorf online store you can buy various brand products:

• one- and two-chamber refrigerators;
• induction and gas hobs;
• electric ovens with microwave and microwave mode;
• narrow and full-size dishwashers with air-conditioning or turbo drying;
• multifunctional coffee machines, high-performance hoods and other types of kitchen equipment.

Prices fluctuate widely. However, any model, regardless of cost, is of excellent quality and perfectly fits its purpose. The price primarily depends on the set of functions. For example, you can purchase for 141 thousand rubles, which will allow you to cook food in seven modes, steam, grill and defrost food. And with programs for automated preparation of various dishes, it costs 318 thousand rubles.

In order to get acquainted with the full line of premium-class equipment, you can go to the official website of the manufacturer. The Hausdorf store, the official distributor of the brand, presents models that are in the highest demand among consumers. Reviews say that the equipment of the old French brand is the equipment of the future. Thanks to long-term cooperation with the company, our online store is able to offer competitive prices. Buyers can use the courier delivery service in Moscow.

Gas floor atmospheric boilers De Dietrich (De Dietrich, De Dietrich) of the ELITEC DTG 130 Eco.NOx series

The device of the floor gas heating boiler De Dietrich DTG 130

The number after DTG 13 indicates the number of heat exchanger sections.
Program block, installed on the gas block, provides control of the sequence of ignition, operation and shutdown of the gas burner of the boiler.
In the gas control unit there are regulating and safety valves installed in series with soft opening, controlled by the boiler regulation circuit.
The ignition electrode ignites the ignition burner with a high-voltage spark.
Ionization sensor detects the presence of the ignition burner flame.
Thrust sensor, located on the rear wall of the draft stabilizer, in case of leakage of combustion products, turns off the burner and puts the boiler into standby mode for 15 minutes. After this sensor has cooled down and waited for 15 minutes (indicated by a flashing indicator on the control panel), the DTG 130 boiler starts up again.

Advantages of De Dietrich DTG 130 Eco.NOx floor standing gas boilers

• The boilers are convenient and easy to install: they are equipped with a multifunctional stand with adjustable legs and handles for carrying, an easily accessible and convenient area for electrical connections, there are hydraulic modules for the heating circuit with the ability to connect to the boiler on the right or left.
• Easy maintenance and repair of De Dietrich boilers: hinged and removable front panel with direct access to the boiler components, as well as a painted draft stabilizer with a cleaning hatch.
• Heat exchanger made of very durable eutectic cast iron, allowing operation at low temperatures (up to 30°C) in the flow line without any risk of reducing the life of the boiler.
• Very low emissions of nitrogen oxides, as De Ditrisch DTG 130 gas boilers are equipped with fully premixed burners equipped with a safety unit.
• A draft sensor with a time delay of 15 minutes is provided
• No permanent pilot flame. Instead, an electronic ignition system using a pilot burner is used, which consists of 1 ignition electrode, 1 ground electrode and 1 ionization sensor, which ensures greater safety of the boiler ignition process.
• System of protection of a tank of a water heater against corrosion "Titan Active System" with automatically adjusted current which does not demand maintenance throughout all term of operation of a copper of De Dietrich.
• Comfortable operation of De Dietrich gas boilers: the main controls are accessible under the cover of the control panel; easy start-up of the boiler by pressing one switch, even after a long period of inactivity, thanks to a new programming unit that makes three start attempts before entering the blocking mode; quick and easy nozzle changes when switching from natural gas to propane.
• Very low noise level< 41,9 Дб.
• Supplied in 2 packages: complete boiler and a separate control panel, which is easy to mount thanks to the “drawer” fixing system.

Boiler control panels of the ELITEC DTG 130 Eco.NOx series

De Dietrich boilers are equipped with two control panels to choose from, initially containing DHW priority:
- base panel B: control panel with built-in control (with priority) of the domestic hot water temperature in the DHW cylinder. Panel B allows the control of one or two direct heating circuits with the possibility of connecting one or two room temperature thermostats (supplied as accessories);

- Diematic 3 panel: multifunctional microprocessor control panel is designed for all types of heating installations, including the most complex ones.

Technical characteristics of De Dietrich floor standing gas boilers of the DTG 130 Eco.NOx series

• Cooling furnace principle.
• 60 mm mineral wool thermal insulation for the boiler heat exchanger, and 100 mm thick for the draft stabilizer.
• Chimney type: B11BS

Overall and installation dimensions of boilers DTG 130

Gas floor atmospheric boilers De Dietrich series DIETRIGAZ DTG X ... N

High-performance cast-iron heating boilers with atmospheric gas burner, electronic ignition and high combustion efficiency (92-93%), designed to run on natural gas or propane.
These boilers of various capacities (from 23 to 54 kW, power step 6 kW) provide heating for rooms ranging from 230 to 540 sq.m. and come in 1 pack.

To ensure not only the heating functions of the boiler, but also hot water supply, a De Dietrich GMT 130 domestic hot water heater can be used together with the boiler.
The tank is made of high-quality steel and coated on the inside with vitreous drinking-grade enamel, which protects the tank from corrosion and retains all the properties of sanitary water.
Water heaters De Dietrich GMT 130 are equipped with a thermometer, perfectly harmonize with the appearance of the boiler and can be installed on any side (even under the boiler).
When adding an additional DHW cylinder GMT 130, a boiler/cylinder connection set with charging pump and hot water priority and temperature control module MB2 (AD 128) is also required.

The De Dietrich GMT 130 B water heater can be installed next to the boiler (all models) or under the boiler (models 30 N and 36 N only) and allows DTG X boilers to provide central heating + hot water. Any other De Dietrich water heater with a capacity from 150 to 500 liters can also be connected to the DTG X boilers as an accessory.

Boiler device DTG X

Advantages of De Dietrich DTG X floor standing gas boilers:

Technical characteristics of gas boilers De Dietrich series DTG X ... N

• Low temperature gas boilers running on natural gas or propane.
• The minimum temperature of the heat carrier at the boiler supply: 30°С.
• Minimum temperature of the heat carrier in the return pipe: no limitation.
• Maximum operating temperature: 100°C.
• Maximum working pressure: 4 bar.
• Adjustable thermostat: 30-90°C.
• Boiler safety thermostat: 110°C.
• Cooling furnace principle.
• Chimney type: B11BS

Overall and installation dimensions of floor standing gas boilers DTG X

Accessories for floor-standing boilers DTG X ... N

MB2 module for hot water temperature control, provides boiler loading priority (art. 88017842)
AD 140 Non-programmable room temperature thermostat (art. 88017859)
AD 137 Programmable room temperature thermostat wired (art. 88017855)
AD 200 Wireless programmable room temperature thermostat (art. 88017018)
The RX 77S control module provides two heating circuits (one of which can be a mixing circuit) and a DHW circuit (Art. No. 100008844)
AD 238 Room temperature sensor (art. 100010844)
AD 239 Adjustable room temperature sensor (art. no. 100010845)
A flow sensor (art. no. 100010843) is required to monitor the mixing circuit temperature
Included in the factory supply:
Outside temperature sensor
Boiler water temperature sensor
Boiler sensor

Conversion of De Dietrich gas boilers from natural gas to propane

Boilers can be easily converted to propane with a simple change of nozzles on a gas burner.

The specialists of the company "Termogorod" Moscow will help you choose the right one, buy as well as install the DE DIETRICH Floor Boiler, find an affordable solution. Ask any questions you are interested in, telephone consultation is absolutely free, or use the form "Feedback"
You will be satisfied cooperating with us!

Gas boiler De Dietrich - an overview of floor and wall models

5 (100%) votes: 2

The De Dietrich gas boiler is a quality standard and a model of heating technology; it competes with other successful units. These French devices are very economical, their operation is efficient and reliable. The difference between De Dietrich boilers is a special cast iron heat exchanger, which is characterized by high strength and long service life. This technical solution contributed to an increase in the productivity of equipment, an increase in its efficiency and extension of the operating period.

Sectional high-performance boiler with cast-iron heat exchanger De Dietrich GT124

From the history of the company

Among French manufacturers of heating equipment, De Dietrich is considered the number 1 brand. The developers of gas equipment are trying to achieve its maximum energy efficiency and environmental friendliness.

You can find out the price and buy heating equipment and related products from us. Write, call and come to one of the stores in your city. Delivery across all territory of the Russian Federation and the CIS countries.

The history of the brand is very long, it begins in 1684 with the acquisition of a small forge by Jean Dietrich, the founder of the company. In 1778, the company received a logo from Louis XVI. The brand is considered the oldest in France. In 2009, the company merged with the huge Baksi concern. It is currently part of the BDR Thermea holding. Every year, 300,000 boilers are produced under the De Dietrich brand.

Advantages of the units

The De Dietrich gas boiler has incomparable advantages over competitors' products, namely:

1. Copper heat exchanger coated with an aluminum and silicon dye, which increases the heat resistance of the metal.
2. Two valves in the gas block that are responsible for safety, as well as a power modulation device.
3. Atmospheric stainless steel burner has a ramp, which makes the pressure stable.
4. Electronic ignition. Flame intensity is controlled.
5. Electronic control panel with display.
6. Possibility to expand control by connecting thermostats inside and outside the house.
7. The hydraulic block, which is made of composite materials (brass in MS 24 and MS 24 FF), has a pump with two speeds. The block is equipped with manometer, and a drain cock and an automatic bypass .
8. Models with an open combustion chamber are equipped with a draft sensor, and those with a closed furnace are equipped with a relay that responds to air pressure.
9. The heating circuit has an expansion tank of 6 liters.
10. The boiler is supplied with a mounting bracket for wall mounting.

It must be said that all Dietrich gas boilers cost a lot - from 30 to 100 thousand rubles, depending on the series and power characteristics. At the same time, there is no doubt about the reliability, quality and long service life of the equipment.

Possible problems

The owners of these French boilers will be notified by a special signal in case of malfunctions. When an “error code” appears on the display, you just need to open the instructions and find the appropriate decoding. As practice shows, almost always you need to contact a service center, because a high-level assembly also needs professional service.

Gas equipment De Dietrich is a traditional quality and modern technology. This technique differs from competitive devices in the following features:

1. burner. In different models, design solutions are used that allow you to mount equipment with forced and natural air supply to the room. Atmospheric units from Dietrich gas make it possible to feed a ready-made gas mixture into the furnace. Mixing with air is carried out in a special injection chamber. This greatly enhances efficiency. French gas burners can apply the principle of forced air injection. In this case, efficiency is achieved due to the rapid heating of the heat exchanger.
2. Heat exchanger. Particular attention to this parameter should be paid to the condensing type boiler. It works according to this principle. Classic water heaters are characterized by a large amount of heat loss in the smoke removal process. Mounted De Dietrich almost do not have this drawback due to the fact that the smoke is removed in a broken way. That is, the chimney repeatedly changes its direction. Thus, the heat is accumulated, and the air at the outlet of the chimney is barely warm.
3. Electric ignition. All models of French boilers are distinguished by the possibility of such ignition. The boiler automatically turns on when the burner flame goes out. This solution saves gas and eliminates the need for constant burning of the igniter.
4. configuration. The De Dietrich hinged gas boiler is perfect for heating small houses and cottages, as a rule, it is used for domestic needs. When the area of ​​​​the room for heating is large, it is recommended to use floor units that are larger in power and more productive. If you wish, you can buy equipment that will operate on a mixed fuel supply system (balloon and natural gas).
5. Additional features. Different models of boiler equipment have certain options and capabilities. Many modifications are low-temperature, contribute to maintaining the temperature regime, which is automatically adjusted depending on the time of year.

When choosing this heating technique, you should pay attention to the following nuances:

1. Location. The technical parameters of the building and the need to heat a large area can affect the choice of a particular model. For example, the De Dietrich floor-standing gas boiler is characterized by high performance and can easily heat a large area. Often this model also has a built-in water heater. This solution is very beneficial, even better than the presence of a second circuit. Minus - a lot of weight. And this may lead to additional preparatory work. The hinged one is smaller in size, it saves space and can be mounted on any supporting wall.
2. Marking. It also plays a role, you should pay attention to the marking when choosing the optimal unit. For example, the De Dietrich floor-standing boiler of the DTG line operates only on natural gas, and the GT series models operate on diesel fuel or gas, etc. these models have the ability, as a rule, to mount on the floor. Mounted gas units are the MS line, equipped with a remote control, a weather-dependent sensor, they are the most comfortable for the user.
3. Multifunctionality. You can buy a device with a built-in boiler or with the ability to heat liquids using a flow method. Usually, a De Dietrich mounted boiler is used as a 2-circuit boiler, because the main requirement for such a model is considered to be low weight, in this case it is impossible to use a large built-in container for heating the liquid.

Take note that almost all appliances: De Dietrich gas floor standing boilers and wall mounted models are energy dependent. This means that for their stable operation it is necessary to install power either. It is worth saying that the electronics in these models are quite sensitive to fluctuations in electrical energy, and you can solve this drawback by purchasing a surge protector or a power rectifier.

Mounted models De Dietrich

Dietrich wall-mounted gas boilers are low-temperature condensing devices that function for heating and heating water for domestic needs. On average, as practice shows, the service life of the units is 15 years.

ZENA MS

Gas convection boiler De Dietrich ZENA MS 24

This model of a wall-mounted apparatus belongs to single-circuit ones, with an open combustion chamber and automatic ignition. The equipment is regulated in various ways - by means of an electronic system or a home and street temperature sensor. The boiler is compact, so it can easily find a place in a small room.

Zena Plus

This model is presented in a wall-mounted version, has two circuits - for heating and supplying warm water. The boiler is low-temperature, with a high performance of the heat exchanger - up to 14 l / min. Power is 24-31 kW.

INNOVENS MCA

Gas condensing single-circuit boiler Innovens MCA 35

An excellent technique embodying an innovative approach and high efficiency. Model hinged, condensation. The efficiency factor is more than 100%. Recycles the heat of waste gases. Electric ignition, modulating burner available. The unit is very economical, the only negative is the considerable cost.

INNOVENS PRO MCA

All De Dietrich gas boilers in this range are small in size, have high power - up to 115,000 watts.

NANEO

Condensing double-circuit boiler Dietrich Naneo PMC-M 24

This unit is wall-mounted, with two circuits for heating and hot water supply, with a turbocharged system. There is protection against pressure drop, flame extinction, liquid heating and lack of thrust.

Boilers of this series are very economical. Compared to similar traditional devices, they save up to 40% of energy resources. And with everything they are characterized by compact dimensions and a small weight of 25 kg. For the purpose of regulation the removable control panel is provided.

MCR-P

This is a De Dietrich gas boiler of a hinged type, condensing. With low power - up to 39 kW, but high efficiency. The model is easy to install, the depth is only 40 cm. Based on the connected device, they can work both in accumulative and flow type.

Of course, these are not all models. There are a lot of mounted boilers in the assortment of De Dietrich. In this case, only the main lines were considered, which will give an idea of ​​​​the capabilities of the units of the popular French brand.

Floor models De Dietrich

De Dietrich floor-standing gas boilers are high-power equipment of large dimensions. As a rule, they are purchased for heating houses, buildings, premises for production. Such devices require a separate boiler room that will comply with operating standards.

DTG 230

Gas floor atmospheric boiler for heating DTG 230-10 with control panel

These are low temperature cast iron boilers. They are easy to install and maintain. Available with 2-stage burner. The gas is pre-mixed with air. If desired, the boiler can be converted to work on propane (reconstruction kit available).

GT 336

This is a floor-mounted single-circuit unit with the ability to connect. The standard equipment includes pressurized burners. If desired, the boiler can be converted to work on liquid fuel.

DTG

This is a line of De Dietrich floor standing gas boilers with a power range of 18–48 kW. Boilers are produced specifically for the Russian climate. Production material - cast iron. Unit type - low-temperature, convection. The combustion chamber is open. There is weather-dependent automation. The series is intended only for heating.

The range of De Dietrich gas boilers is wide, and it is not limited to the above models. But no matter which boiler of this company you choose, it will be a high-quality, durable and reliable source of heat for your home. The brand has been a leader in the heating technology market for many years, providing premium-class equipment throughout Europe.