Lampshade made of jute and a ball with your own hands. DIY thread lampshade: master class, step-by-step description and recommendations. DIY chandelier

When there is a desire to change the situation in the apartment and add a little originality to it, start with the little things. Try to change the lampshade, and you will be surprised at the transformation of your family nest.

And if you manage to find an original model that differs from analogues, then the changes will impress not only you, but also your guests.

True, unique lampshades cost decent money, because you can’t get piece work by eminent masters for a penny.

But after all, no one bothers you to create your own unique masterpiece from cheap, and sometimes even junk materials, which will look much better than the samples presented in the store.

All you need is simple materials, a little patience and a flight of fancy, and we will tell you how to make a lampshade with your own hands.

materials

You can create a masterpiece from everything that you have at hand: fabric, paper, thread, twine, wire, plastic bottle, beads or beads.

In general, absolutely everything is suitable, even what you usually send in a garbage bag.

Don't believe? Just look at the photo of the lampshade.

frame

If you have a frame from an old lampshade, then this is just wonderful.

However, do not be upset if one is not found, because you can create a frame yourself from ordinary wire.

Copper, aluminum, steel - everything that you can independently combine into a single structure will do.

The metal frame of the classic lampshade consists of three rings and six jumpers between them. The small ring is a holder, which is connected by three jumpers to a ring of a larger diameter.

The same, in turn, is connected by jumpers to the last ring. The following photos will help you understand the design.

From fabric

When a lampshade frame is available, the easiest way to create your own masterpiece is to wrap the base with a cloth. For this you will need:

• paper (newspaper);
• scissors;
• textile;
• chalk or pencil;
• threads.

Wrap the frame with newspaper in such a way as to form a pattern out of it. Then transfer the resulting shape to the fabric with chalk, adding 1 cm on each side to the seam.

Make a pattern, chop off the edges and sew the sides, forming a cover for the base of the future lampshade. We bend the upper and lower edges of the "cover" in such a way as to close the rings of the frame and fix it with a seam.

Note!

Voila, your lampshade for the floor lamp is almost ready. It remains to add a few highlights to your taste, giving it originality.

From threads

How to make a lampshade when there is no frame? As easy as pie.

Take a balloon without drawings, glue, thread, marker and start creating.

First you need to inflate the balloon and mark on it the upper and lower borders of your future masterpiece. Then take the threads and wrap them around the ball, trying not to protrude beyond the marked contours.

Apply glue diluted 1:1 with water to each layer of thread. When the density of the wound thread satisfies you, fix the cut edge and hang the ball to dry. After 3-4 hours, the threads will dry. Then pierce the ball and carefully detach it from the walls of the finished lampshade.

Leaves and flower petals woven between the layers of threads can give additional charm to a lampshade made of threads.

Note!

The ball, decorated with sparkling droplets of beads, also looks original. In general, watch and be inspired.

From paper

Ordinary sheets of office paper, glossy magazines, a cheap newspaper, an unnecessary book or an ordinary notebook, a paper towel or a napkin - these are all future lampshades.

It doesn’t matter if there is a frame or not, the main thing is that there are scissors, glue and paper. A thousand and one versions of such lampshades can be described with the words “cut and stick”.

The main thing is not to forget a few simple rules:

• a paper lampshade is safest to use with economy light bulbs, which heat up much less than incandescent bulbs;
• the diameter of the lampshade for lamps should be large so that the paper does not get too hot;
• for a bright room, you can make a lampshade from thick paper, but for a dark one, you need a thin, well-transmitting light;
• be careful with color. For example, red or yellow paper will add warmth to the room, green and blue - cold.

Well, that's all. Charge with new ideas, arm yourself with improvised means and forward to easy changes that bring warmth and comfort to your home.

Note!

DIY lampshade photo

A do-it-yourself lampshade master class will help transform an old lamp and update the interior. You can make a beautiful designer lampshade from various materials. Designers from all over the world are experimenting with cardboard milk packaging, threads, plastic bottles, fabrics, etc. to make an original lamp. There are quite a few options for creating a lampshade from improvised materials.

A Few Ideas

The decor of the lampshade creates the overall impression of the lighting of the room and can make it cozy or, conversely, repel. It all depends on the ability of the lampshade to transmit light and transform it into different colors. For example, a white lampshade lets in more light than a dark blue or black one, so in the first case the room will be brightly lit, and in the second case the lampshade will create an intimate and relaxing twilight.

It is worth considering when creating a lampshade at home that each room requires its own light. At the same time, the lamp should fit well visually into the overall interior.

The kitchen needs a lot of light, and lampshades are made from simple, often natural materials - rope, wooden sticks, straw, paper, etc.

For living rooms, floor lamps and chandeliers with more “smart” lampshades are suitable. They can transmit light well for bright lighting or, on the contrary, muffle it, it all depends on the mood (“outfit” of the lamp can be changed depending on the situation).

In the bedroom for a table lamp, delicate lampshades with lace, ruffles, and frills that do not transmit light well are suitable. Most often they are made from warm shades of fabrics to create a cozy soft light in the room.

It is easy to experiment with an old frame or fabric lampshade: there is no need to think about how to attach the lampshade, while there is great scope for creativity. It is only necessary to stock up on the necessary materials and tools and you can start fantasizing.

Getting Started

Before you understand how to make a lampshade for a floor lamp or lamp, you need to choose the right materials. What can you make a lampshade from:

• ropes and threads of different thicknesses;
• paper and cardboard, including photographs;
• from any fabric, as well as individual shreds and lace;
• beads and beads.

You can combine these materials with each other, for example, decorate fabric with beads, and paper with ropes.

One of the simple lampshades is made of twine. It looks good in the kitchen or on the terrace. The execution technique is probably familiar to many from childhood. It is necessary to inflate a balloon or a sports ball and wrap it in a chaotic manner with twine smeared with glue. After it is completely dry (it may take 24 hours), pierce the ball or blow off the ball and attach the lampshade to the lamp.

Instead of twine, you can use ordinary cotton threads. Lampshades are thinner and more elegant.

From threads, as well as from woolen yarn, you can also crochet or knit a lace or mesh lamp case. It can turn out to be a very cozy lampshade.

You can make stylish lampshades for living room floor lamps out of paper. Paper transmits light quite well and at the same time is an excellent material for the manifestation of fantasy. Paper can be painted with paint or glued to it with applications and other decor. If you cut a pattern in paper using a stencil, you get a lacy paper lampshade. And if you glue the lampshade with black and white photographs with your loved ones, then you can not only enjoy pleasant light, but also joyful memories.

A few ideas for decorating a lamp with a paper lampshade can be seen in the photo below.

To make a lacy paper lampshade, you will need the following materials and tools:

• paper;
• glue (preferably a pencil);
• scotch;
• stationery knife and ruler;
• thick wire;
• pliers;
• a metal plate that will hold the lampshade on the lamp (you can take it from an old chandelier or use a part for laying pipes).

It should be remembered that the paper must be of sufficient length. This is necessary for safety: when folded, the sides of the paper must be at least 15 cm away from the light bulb, i.e. The length of the paper should be approximately 35-40 cm.

Progress:

1. Step back from the edge of the paper about 20 cm and outline the pattern with a ruler and pencil - geometric shapes and patterns;

1. Cut patterns along the lines with a clerical knife;

1. Roll up the lampshade and seal around the edges;

1. Lay the wire inside around the circumference, bend the paper edges and glue with tape;

1. Attach the lampshade to the metal plate with two pieces of wire, hooking the wire rim inside the paper, fix the entire structure on the light bulb.

For those who know how to sew, it will not be difficult to sew a fabric lampshade. In order for the lampshade to “sit down” as needed, first of all, it is necessary to take measurements and build patterns according to the finished frame.

For work you will need:

• textile;
• pencil;
• ruler;
• tape measure;
• pattern paper;
• threads;
• pins;
• sewing machine.

A fabric lampshade can be made in two ways: completely sewn like a cover and pulled over the frame, or impregnated with a fabric pattern with special glue and pasted over the frame with it after complete drying. The first option allows for creativity and may require some sewing skills. The second option is simpler and faster.

It is well known that any product made by human hands is much more interesting and beautiful than mass-produced products. This explains the great demand around the world for handmade products, which has appeared in recent years. Of course, you can buy a finished jewelry from a craftsman or order it according to your own sketch, but is it worth spending money on something that you can make yourself, having received incredible pleasure from the work process itself and, of course, from the finished result?

An excellent material for interior decoration is a rope made of natural fibers. It is not difficult to buy a rope made of hemp, jute or sisal today and it is quite inexpensive, and you can make a huge number of necessary and very beautiful things from it that will decorate the interior of a living space, cafe or club. Rope chandeliers are an example - beautiful, light and invariably attracting attention. Such a chandelier will perfectly fit into the interior in country style or romanticism and can become a real highlight of the design.

Materials and tools

There are a lot of options for chandeliers made of natural ropes. There are both complex designs, the creation of which requires certain skills and the use of a variety of auxiliary materials, and very simple ones, which anyone can make. One of the simplest lamps of this type is "Spider" - a ceiling chandelier that will perfectly complement the interior in industrial style.

For work we will need:

• or hemp, with a diameter of 20-30 mm;
• Two-core wire, for example, ShVVP 2x0.5 mm;
• Lampholders, by the number of lighting elements;
• Incandescent lamps 40-60 watts;
• The base is from an old multi-track chandelier or a self-made wooden bowl with holes, according to the number of "horns".

Getting Started

The most difficult part of the job is putting the wire inside the rope or rope. Of course, we will not unwind the rope and re-plait it with the conductor inside. To place the wire in the rope, you just need to take it by the ends and start rotating them in different directions. In this case, the strands diverge and it is quite possible to place a wire of a small cross section between them. After the wire is inside the rope, we connect a cartridge to one of the ends of each part. Our lamp will be without shades, so the cartridges need to be decorated. One of the simplest options is to color them in a color that matches the rope, but the most aesthetic option can be obtained by slightly unwinding its ends and winding strands around the cartridge. In order for the winding to hold, it must be properly glued.

When all the elements are ready, you can proceed to chandelier assembly. We pass the wires through the holes in the base and connect them to the main cable, through which power will be supplied to the chandelier. It is important to be especially careful here and observe the polarity. All connections must be carefully insulated with electrical tape or. The ends of the ropes should not be run into the bowl in order to comply with fire safety rules. Before fixing the chandelier on the ceiling, you can dream up a little by tying the ropes with picturesque knots.

The Spider chandelier is attached to the ceiling in several places - in the center, like a regular ceiling lamp, and also in the center of each individual rope element. To fix the product, you can buy self-tapping hooks. Separately, it should be said about the lamps used with the rope chandelier. To avoid overheating, do not use too powerful lamps - it is enough to take 40-60 watt lighting fixtures. The now popular Edison incandescent lamps with unusual stylized glass bulbs and intricately laid spirals look great with such a chandelier.

Helpful Hints

Materials: scissors large and small, pliers, tweezers, candle, matches, egg containers, plastic bottles, coffee beans, tangerine skins, pasta, beads, jute twine, PVA glue, balloon, old lamp base, acrylic for coloring flowers paints, glass paints, stained glass paints, nail polish, hook, glue gun.

So. Here are the remains of an old lamp lying around. It's a shame to throw it away. Wanted to update. I inflated the balloon to the right size. I tied it so that it would be easy to untie. I tied a load to the end of the rope / in my case an iron rod /, for stability, and put it in a jar. I smeared it with PVA glue and wrapped it with jute twine on top. Then I thoroughly blotted the entire PVA structure. It is best to do this with a sponge so that the twine is completely saturated with glue. Everything, we forget about the ball exactly for a day.

Let's prepare the decorations.

I do orange spirals like this - I clean the orange from the insides along with the zest, cut the orange peel into strips and roll it into spirals, fix it with toothpicks and also forget it for a day.
I paint pasta with paint and nail polish.

Let's move on to flowers.
I am collecting bottles and a container for eggs.

For bottles, you can use the bottom and neck for flowers. for leaves - the middle. The egg container is the most convenient for making flowers. You just need to cut out the cells and cut through the petals.
Further. If you have a gas stove - this is the best option! I have not it. I will bend the petals over the candle. By trial and error, I calculate the required distance so that the petals do not melt at all, but simply bend and begin to look like flowers.

When all the blanks are ready, I collect flowers from them - inserting several blanks one into another and gluing with a hot gun. Then I take the above paints and nail polish and start painting my flowers. Here's what comes out.

The ball has dried up, I untie the rope and remove the ball until the next work. It remains a beautiful ball of twine. I cut out the bottoms. One more will go to the leg of the lamp, the second will not be needed in this product. I braid the base of the lamp with jute twine, and with the same twine I attach the resulting lampshade to the base. I crochet three chains. Two for the design of sections of the bottom on the leg and one - for the design of the upper section of the lampshade. I sew the top. I glue it on the leg with a glue gun.

I make a composition of flowers, leaves, beads, coffee, pasta and spirals. I glue everything with a hot gun. The lamp is ready.