Menu

Weber Vetonit

М-150 De Luxe universal mixture

The purpose of the universal cement-sand mixture M-150 is external, internal construction, finishing, repair work, such as brickwork, primary plastering, the construction of partitions and curtain walls, sealing, seam processing. The recommended layer thickness is 5-50 mm. For a layer 10 mm thick, 16-18 kg / m² will be required.

M-200 Assembly and masonry mixture De Luxe

The purpose of the dry mix M-200 (sand concrete De Luxe) is external, internal construction, finishing, repair work, such as brickwork, block laying, floor screed, seam processing, wall repair, crack sealing. The recommended layer thickness is 5–50 mm. For a layer 10 mm thick, 16–18 kg / m² will be required.

M-300 Pouring mixture (de Luxe sand concrete coarse-grained) De Luxe

The purpose of the M-300 is external, internal construction work, such as pouring foundations; erection of walls and foundations; the device of a coupler, a bearing layer of floors, including those used as finishing in production and storage rooms. The minimum layer thickness is 35 mm. The maximum filler fraction is 3 mm. For a layer 10 mm thick, 18-20 kg / m² will be required.

As an official dealer, we offer to buy in bulk the most popular dry mixes M-150, M-200, M-300 at an attractive price. There are discounts for wholesalers: when ordering from 20 tons, the price is reduced per unit, which will ultimately bring you a solid benefit. Contact us by ordering a call back, or place an order for the purchase of dry mixes online on our website.

Marking of dry cement-sand mixtures

Comprehensive information about the composition, class, introduced additives, methods and areas of application of the material, its shelf life and release date, weight, technical parameters of the DSP are placed on the packaging. Information about the appointment is marked:

• universal plaster - M-100;
• universal - M-150;
• assembly and masonry mixture - M-200;
• casting, foundation - M-300;
• pouring, foundation especially strong - M-400.

The number in the marking indicates the load (static) that the hardened mortar can withstand, for example, the dry assembly and masonry mixture M-200 can withstand a load of 200 kg / cm³.

The presence, qualitative and quantitative composition of additives change the purpose of CPS, as they expand the possibilities of its application. Additives affect adhesion, water repellency, strength and price of the dry mix.

Classification of cement-sand mixtures

According to GOST 28013-98, dry cement-sand mixtures are classified according to density, amount of binders, and purpose. By density, DSPs are divided into light and heavy; by the number of binders - into simple and complex, containing one or more substances, respectively; by appointment - for plastering, masonry, pouring. The standard regulates the parameters of solutions of mixtures:

• humidity,
• temperature range,
• plastic,
• density,
• stratification.

The hardened solution is evaluated by frost resistance, density, strength.

WEBER VETONIT cement facade plaster for leveling surfaces with a layer of 5 to 30 (50) mm:
frost-resistant
For interior and exterior use
high adhesion and vapor permeability
elastic
non-shrink

BENEFITS:
Can be applied to concrete without prior priming of the surface.
It has good adhesion to all common building substrates.
Easy to apply, hardens without shrinkage.
It is moisture and frost resistant.

SPECIFICATIONS:
Leveling of mineral surfaces with a layer of 5 to 30 (50) mm, before tiling, puttying, painting.
For vertical and horizontal surfaces, indoors and outdoors.
Suitable for application on the following substrates: concrete, ceramic and sand-lime bricks, cellular concrete substrates, over previously applied cementitious plasters.

INSTRUCTIONS FOR USE
*Preparatory work:
The base must be dry, solid and must not shrink or warp.
The base must be cleaned of dust, dirt, old paint, mortar and degreased.
At an ambient temperature above 25°C, before applying the plaster, it is recommended to moisten the base.
The substrate temperature must be at least +5°C.
For work at temperatures from - 10 ° C to + 10 ° C and with possible night frosts, use weber.stuk cement winter.
Highly absorbent substrates must be primed with weber.prim multi or weber.prim A10 (pre-diluted 1:4 with
clean water).

Mixing:
Pour 6.25 liters of water into a container and pour 25 kg of plaster (bag).
Mix weber.stuk cement in clean water at a temperature of approximately 20°C.
It is necessary to knead the mixture mechanically using a drill mixer at an average speed (400 - 600 rpm) to achieve a homogeneous mass without lumps.
Leave the mixture for 5-10 minutes to "ripen", then mix again.
After that, you can apply the plaster on the wall by throwing or using a grater and trowel.
The permissible thickness of one layer is up to 30 mm, a greater thickness can be obtained by applying the solution in several layers with intermediate drying of each layer
at least 12 hours.
At 20°C and normal humidity, the prepared solution remains viable for at least 2 hours.

Note:
During drying, the plaster must be protected from high temperatures, direct sunlight and wind.
When applying weber.stuk cement for the first time or when environmental conditions change, it is advisable to check and establish the optimal proportion of water and mixture on a small area, and then adhere to it.
If there are expansion joints on the base, then when applying the mixture, it is also necessary to make expansion joints, repeating their geometry and filling with polyurethane sealant.

Application:
The prepared solution is applied manually or by machine on a previously prepared surface.
Without waiting for the surface to air, the solution is smoothed out using the appropriate tool.

TOOL CLEANING:
Working tools and equipment are washed with water immediately after completion of work.

PRECAUTIONARY MEASURES:
Rubber gloves must be used when working
avoid prolonged contact with skin and eyes
In case of contact with eyes, rinse with plenty of water. Keep out of the reach of children.

DISPOSAL INSTRUCTIONS:
Dry mix and hardened material must be disposed of as construction waste.
The material must not be released into the sewer.
Dispose of the paper bag as normal trash.

Packing:
Paper three-layer bag with a middle layer of polyethylene - 25 kg.
Pallet 48 bags/1200 kg.

Storage:
12 months from the date of production, when stored in its original packaging on a pallet in a dry place.

Description
Vetonit TT - waterproof cement-based plaster-primer; the best material to use as plaster for a brick wall. Can be used in dry, damp and wet areas. Plaster Vetonit TT is an economical, practical and durable material that is easy to apply, excellent adhesion, sanding and does not shrink.

Areas of use

• Preliminary leveling of surfaces of internal walls made of mineral materials.
• Alignment of wall surfaces from.
• Leveling and repair of old, plastered surfaces.

Foundation and application
Vetonit TT can be applied directly to brick, concrete, aerated concrete, as well as new cement plaster or primer. The basis under Vetonit TT has to be firm, dry, cleared of dirt and dust. Substances that weaken adhesion to the surface, such as dust, paint, oil, etc., as well as water-soluble leveling compounds, must be removed. Windows and other surfaces that are not processed are recommended to be closed with film and adhesive tape. If necessary, dry and absorbent surfaces are moistened.

Plaster Vetonit TT can be sprayed onto the base using a compressor or applied manually using a steel ruler or. If the surface is uneven, then it is possible to apply several layers of the composition, after making sure that the previous layer is completely dry. Each dried layer requires grinding with an abrasive material and is additionally moistened in dry rooms. The drying time of the layer is one day at room temperature. To make the surface smoother, a slightly dried layer is wiped with a damp sponge. The completely dry surface can be veneered or painted with alkali-resistant paint. But usually coarse-grained "TT" (maximum fraction - 1 mm) is coated with fine-grained compositions before painting: in damp and damp rooms - "V" - "VH", and in dry ones - "LR" or "T" - "KR".

ATTENTION!
Vetonit TT mixture is not suitable for painted surfaces, for surfaces leveled with water-soluble substances, for example, Vetonit T, KR, L, LR or lime levelers, not suitable for leveling floors. Leveling mortar can clog pipes, do not pour the remaining primer mass into the sewer. Vetonit TT mixture is not suitable for leveling floors.

Vetonit is a brand that produces powdered building mixes used for a wide range of finishing and construction work. Among the most popular products are wall and ceiling finish putty, floor leveling screeds, and tile adhesive. The products have gained mass distribution due to their excellent qualities and affordable price. The production of dry mixes in Russia is carried out by Weber-Vetonit, which is an industry division of the international industrial and construction group Saint-Gobain. The article will discuss the main features of dry mixes vetonite.

Briefly about the manufacturer

• The Saint-Gobain company is one of the largest corporations in the world for the production of building products. It was founded in France in the middle of the 17th century, and today it has 1.5 thousand companies in more than 60 countries around the world. The head office is located in Paris. Building mixtures are just one of four areas of activity in which the corporation consistently occupies a leading position.

• In 1992, the Weber company, specializing in the production of building materials, joined the Saint-Gobain industrial group. Weber has been leading its history since the beginning of the 20th century, when J. Weber and J-B. Bruten began to make facade plasters. Today, Saint-Gobain Weber has more than 200 branches in 42 countries, and after the acquisition of the Maxit industrial group (MaxitGroup), its factories appeared in the Russian Federation.
• All manufactured products meet the highest European requirements, which is confirmed by international quality certificates. Vetonite are versatile and highly specialized materials for finishing almost any surface.

Consumers who opt for Vetonite are guaranteed to get excellent results, but how can this be achieved?

Vetonite characteristics

Putty vetonit

• Putty mixtures are used for the final leveling of surfaces, the quality of their application directly affects the overall impression and appearance of the finished renovated room. Vetonit putties create a perfectly flat surface, and their main purpose is to seal gaps, layers and cracks after rough basic construction work.

• Like all types of putty, Vetonit mixtures are divided into three subspecies: cement, polymer and gypsum. Basically, these are finishing putties intended for facing the ceiling and walls. The basis for their application can be a variety of materials - concrete, drywall, brick, gypsum and others, even a putty has been developed that is applied to painted surfaces.
• Mixtures are universal and are used both indoors and outside the building. Although putties create a perfectly flat and smooth surface, they still do not have special decorative qualities, therefore it is allowed to apply almost any decorating materials over the layer - wallpaper, relief plasters, tiles, acrylic or water-based paints and so on. Putties themselves are not adhesives.

• These are environmentally friendly products that are created only from safe components for humans and nature.
• Due to the excellent water resistance, the mixtures are versatile and can be used even in areas such as swimming pools (the package should be labeled "waterproof mixture").
• Powder mixtures have such a fine fraction that the applied layer acquires an ideal, almost mirror-like smoothness.
• The applied layers of putty are not afraid of adverse weather conditions, including frost, rain or hail, which means that they can reliably serve even with facade decoration for many years. In addition, products have been developed that can be applied even at negative temperatures (snowflake marking on the package).
• The putty layer enhances the heat-insulating and sound-absorbing properties of the walls and ceiling.

Technical specifications

• Release form. All Weber putty products are produced in paper three-layer bags, the middle layer of which is made of polyethylene (dry powder) of 5, 20 and 25 kg or in plastic containers (paste-like substance) of 10-12 liters.
• Astringent. Cement, polymer glue, limestone, gypsum can act as a binder.
• Main purpose. There are several varieties of putty, distinguished by their main purpose:
  1. for leveling a plastered surface or a concrete base before subsequent finishing (painting, wallpapering, ceramic tiling);
  2. for sealing seams formed between sheets of drywall;
  3. applying a putty layer on a previously painted surface.

• The color of the finished composition. The main shades of the applied layer are white, gray or yellow, which corresponds to the color of the purchased dry mix.
• Granule size. Fine-fraction powder mixture, the size of which is 0.3-0.5 mm, the fraction of the pasty substance is not more than 0.06 mm.
• Temperature. The surface during processing and the ambient temperature should be in the range from +5 to +25 degrees (for frost-resistant species from -10 degrees).
• Consumption of products vetonit. On a surface of 1 m2, when applying a layer of 1 mm, 1.2-1.4 kg of dry matter will be required, the consumption when filling joints is 100-200 g/m2.
• To prepare putty, it is necessary to add 290-350 ml of water per 1 kg of powdered substance.
• Viability. The prepared cement mixture should be used within 2 hours, after which it loses its qualities, it is not recommended to dilute it again, if polymer binders are included, then the viability of the finished solution can be 12-24 hours, and if stored in a closed container, up to 2 -x days.
• Full dry time. The applied layer hardens within 3 hours, for complete drying, you should wait at least a day, the greater the thickness of the layer and the number of layers, the longer it takes to dry.
• The thickness of the applied layer. It is recommended to apply 1-3 mm at a time (depending on the brand of goods, a layer of up to 5 mm can be applied in one pass).
• Frost resistance. At least 75 freeze / thaw cycles for powder products and 10 cycles for ready-made solutions.
• Strength factor. After one month, the layer is able to withstand a mechanical load of up to 10 MPa.
• Adhesion coefficient. Adhesion strength to the surface is approximately 0.9-1 MPa.
• Shelf life. The product can retain its quality for 12-18 months, while maintaining the integrity of the original packaging, as well as under proper storage conditions - a dry room where the air humidity is not more than 60%.

Stages of work

• Putty mixtures can be applied to the surface to be treated both manually and mechanized using automatic installations.
• The base must be properly prepared - cleaned of dust and dirt, it must be strong, dry, solid and free of substances that reduce adhesion (oil or grease stains). In the room in which the decoration takes place, windows and doors must be closed to exclude the possibility of drafts.

• To prepare the solution, it is necessary to pour the required amount of water into a large container, preferably made of plastic, the temperature of which is approximately equal to 20-25 degrees (no more than 40 ° C). Then dry powder is poured into the container (it is not recommended to change the sequence) and thoroughly mixed with a construction mixer or a drill with a special nozzle for 5 minutes. After that, the prepared mixture is kept for at least 10 minutes, for better dissolution of the binder, it is stirred again and you can start using it.

• When applying several layers of putty vetonit, it is necessary to dry each previous one. The dried surface, before subsequent finishing, is recommended to be sanded with fine sandpaper and cleaned of dust.

Plaster vetonite

Several types of dry plaster mixtures from the Weber-Vetonit company are supplied to the Russian construction market, which are produced both directly at factories in Russia and in other countries, for example, in Finland.

• Vetonit plasters are, as a rule, cement mixtures, in which sand and limestone can be used as a filler, and additional components such as microfiber are added. The most popular product is the production of "Weber. Vetonit TT" - a universal plaster for most bases.
• Decorative plasters that can create a unique relief are widely used. They can be applied on surfaces previously treated with any type of plaster (cement, gypsum, lime-cement), as well as on gypsum board and gypsum fiber substrates.

Main competitive advantages

• Products can be used on most known materials - concrete, aerated concrete, ceramic or silicate bricks, foam concrete, and so on, preparing the base for subsequent finishing with tiles, glass or plastic plates, as well as for applying putty.

• Vetonit plaster is distinguished by its special frost resistance and water resistance, due to which it can be used for facade work, as well as for plastering bathrooms, warehouses and other rooms with high humidity or low temperatures.
• Non-shrink hardening and excellent adhesion to the surface.

Technical specifications

• Release form. The manufacturer delivers its goods in paper bags, with packaging of 5, 20 and 25 kg. Decorative plasters can be produced in the form of a ready-made solution, in a plastic container of 15 kg.
• Astringent. The binder is cement.
• Main purpose. Depending on the type of product, it can be used in the following cases:
  1. creation of a decorative layer for subsequent painting with water-dispersion paints both inside and outside residential and public buildings;
  2. preliminary leveling of ceilings or walls in rooms with any level of humidity;
  3. local application when leveling surfaces for subsequent construction and repair work.
• The color of the finished layer and mixture. The shade of the resulting layer is gray for simple plasters and light gray for products intended for subsequent painting.

• Granule size. The powdered substance has a maximum fraction size of not more than 1 mm. Decorative plasters, depending on the texture, have fractions from 1.5 to 4 mm.
• Temperature. The solution can be applied at temperatures from +5 to +30 degrees, if the package is marked with an asterisk or there is an inscription "winter", then the plaster is used in the cold season, at a temperature of -10 degrees.
• Consumption of products vetonit. To apply a layer of 1 mm on an area of ​​1 m2, from 1.2 kg to 2.4 kg of dry matter is consumed.
• The volume of water for mixing the mixture. Water consumption per 1 kg of dry matter is from 160 ml to 300 ml (the exact amount is always indicated on the package and it is necessary to follow the recommendations in order to get the finished layer as durable and of high quality as possible).
• Viability. Cement mortars lose their viability very quickly, as a rule, it fluctuates within 2-3 hours.
• Full dry time. Each applied layer must be kept up to 2 days and only after this period of time, you can proceed to subsequent repair work. Within a week after the completion of the finishing, the plaster is gaining 50% strength.
• The thickness of the applied layer. Vetonit plaster can be applied in one pass with a layer of 2 to 10 mm, the maximum thickness is 3 cm.
• Frost resistance. Dry powder is capable of withstanding 75-100 total freeze/thaw cycles.
• Strength factor. After 28-31 days, the applied plaster is able to withstand a load of 6-8 MPa.
• Adhesion coefficient. On a concrete base, the adhesion strength will be within 0.5 MPa.
• Shelf life. It is necessary to store the product in its original packaging, without damage to its integrity. In a dry room, the product is able to maintain its properties and qualities for 1 year.

Stages of work

• The surface for applying the solution must be properly prepared. To do this, it is cleaned of dust and dirt, if necessary, the base is strengthened with a reinforcing mesh. If there are oil or grease stains, they should be removed as they will reduce adhesion. All large irregularities close up. Before applying the diluted mixture to the concrete base, it must be treated with a primer so that the concrete does not absorb moisture from the solution.

• Knead the solution in clean water, room temperature (20-25 degrees). Be sure to follow the sequence in which the dry powder is added to the liquid, and not vice versa. To improve adhesion, 10% water can be replaced with a dispersion primer. Stir the solution with a construction mixer or drill until all lumps are dissolved. In the process of application, the finished mixture is stirred without additional addition of water or other liquid.

• When finishing facades, it is important to protect the applied layer from rain, snow and direct sunlight for 24 hours. The resulting decorative surfaces can be painted after 72 hours; to reduce paint consumption, it is recommended to treat the relief layer with a silicone or silicate primer.

Self-leveling floors / leveler for the floor

Bulk floors are self-leveling mixtures used for floor screed. Products "Weber.vetonit" allows you to create a perfectly flat surface, with a layer thickness of 1 mm to 25 cm in one pass. The solution can be used for floors in residential and office premises, both in new buildings and in structures with a long service life.

Main competitive advantages

• The resulting surface has an almost mirror-like appearance and does not require additional grinding or leveling.
• It can be used as a base for all floor coverings, even for subsequent finishing with very thin materials.
• Due to the high compressive strength, the finished coating is able to withstand heavy loads, in addition, internal reinforcement allows the use of mixtures even on deformable surfaces.

• The mixture has the fastest set of strength, which allows you to walk on the poured layer in an hour, and to lay floor coverings in 2 hours.
• It can be used even on difficult substrates, for example, over old wooden floors, ceramic tiles and other materials, thanks to the addition of special polymer components to the composition.
• Forms a sound-proof, heat-resistant and moisture-resistant layer.

Technical specifications

• Release form. It is produced in the form of a dry powder packaged in three-layer paper bags of 5 and 25 kg, for reliable protection against environmental influences, the middle layer of the package is made of polyethylene.
• Astringent. Special cements are used as a binder.
• Main purpose. Mixes are intended:
  1. for leveling concrete and cement-sand bases;
  2. to create screeds for the subsequent installation of flooring;
  3. to create the main floor layer on balconies and terraces;
  4. for the installation of the "warm floor" system.
• The color of the finished composition. The shade of the mixture is determined by the presence of cement in the composition, which gives the finished layer a gray tint.
• Granule size. The maximum size of the powdered substance is from 0.6 mm to 3 mm.
• Temperature. The solution is poured in rooms with an air temperature of +10 to +25 degrees, it is considered optimal to maintain the temperature within +15-+20 degrees.
• Consumption of products vetonit. When applying a layer of 1 mm to an area of ​​1 m2, 1.4-1.8 kg of dry matter is consumed.
• The volume of water for mixing the mixture. To prepare a working solution for 1 kg of dry matter, 200-300 ml of liquid is added.
• Viability. The prepared mixture requires immediate use, as after 15 minutes it begins to solidify.
• Full dry time. After 1 hour it is allowed to walk on the filled layer, after 2-3 hours you can lay the floor covering.
• The thickness of the applied layer. It is allowed to make a layer, the thickness of which varies from 1 mm to 25 cm.
• Shrinkage. A month after application, the layer may shrink to 0.5 mm/m.
• Strength factor. After 28 days, the self-leveling floor is able to withstand loads up to 30 MPa.
• Adhesion coefficient. Adhesion to concrete base 1 MPa.
• Shelf life. Bags with the mixture are stored unpacked in a dry place for 6-12 months from the date of production.

Stages of work

• The mixture is used indoors. When pouring the floor, it is necessary to tightly close windows and doors and maintain a constant temperature within + 10- + 25 degrees for at least 7 days.
• The base under the self-leveling floor must be cleaned of dust, and also make sure that it is dry and durable (if it is concrete, then it must stand for at least 2-3 months). If the top layer of the treated surface has peeling materials, they should be removed. The place of possible leakage of the mixture is sealed without fail.

• It is best to prime the surface with a special compound, for example, the Weber Vetonit MD 16 dispersion. If it is intended to apply more than 1 layer, then each of them must be treated accordingly. Dispersions and primers prevent the formation of air bubbles and provide better adhesion to the substrate.

• To prepare a working solution, clean water is poured into a plastic or silicone container, and then the dry ingredients are poured out and everything is thoroughly mixed with a construction mixer.
• It is best to use the mixture immediately. It can be applied both manually and mechanically. It is optimal to fill in strips, the width of which varies between 30-50 cm. Starting from the corner, the poured solution is distributed with a steel spatula and rolled with a spiked roller (to release the existing air).

• It is not allowed to take breaks during pouring, if too large an area is being processed, then it should be divided into small sections by setting limits.

Assortment of goods and approximate prices per package

The industrial group "Weber. Vetonit" produces, in addition to plastering and putty products and self-leveling floors, a lot of dry building mixtures that have proven themselves in the domestic market. These materials include adhesives used for the installation of heat-insulating slabs (mineral wool, expanded polystyrene) and for laying porcelain stoneware, tiles, stone slabs, including at sub-zero temperatures. Almost any surface can be used as a base - concrete, drywall, brick, wood, and so on. The table shows the average prices for dry mixes vetonite.

In addition to dry building mixtures, Weber factories produce acrylic, silicate and bituminous paints, primers and dispersions for pre-preparation of foundations and subsequent application of self-leveling floors, putty or plaster, as well as all kinds of impregnations, antiseptics, substrates and injection materials (bituminous pastes, suspensions, improving the properties of the screed, mastics for insulation, and so on).

Entering the store, it is very easy to get lost among the huge selection of goods and products, but Vetonit products can be found right away. These are yellow paper bags (rarely white), on the left side of which there is a strip with the name of the product - 2/3 black (indicate the name of the manufacturer), and 1/3 red, orange, green and other shades (indicate the brand of the product) . By purchasing powdered building mixtures or ready-made solutions of vetonite, you can always be sure that the repair will be of high quality and durable.