Ceresit tile grout: selection, specifications, colors and application. Ceresit tile grout: selection, specifications, colors and application Ceresit grout ce 40 white

CERESIT CE 40 grout is designed for indoor and outdoor use. This is a premium grout with a unique set of state-of-the-art technologies. Grout CE 40 is water-repellent thanks to the innovative "Aquastatic" technology. Water does not soak into the structure of the grout, but rolls off the surface, so the grout lasts longer and has a great appearance. What's more, CE 40 grout has increased resistance to dirt thanks to the Dirt Repulsion technology. Enhanced safety and protection of seams against fungus and mold is provided by the latest formula of antifungal protection - "MicroProtect". And the increased crack resistance of CE 40 allows you to create joints up to 10 mm wide. In addition, the original formulation of CE 40 creates a premium joint surface with a “velvet” effect.

Properties:

• elastic;
• water repellent;
• resistant to dirt, easy to clean;
• has an antifungal effect;
• has a smooth surface;
• waterproof;
• frost-resistant;
• suitable for use on underfloor heating;
• environmentally safe.

Application area:

Grout CE 40 is intended for grouting ceramic, glass and stone facings up to 10 mm wide, on floors and walls, in interior and exterior works, in civil and industrial construction.

CE 40 has low water absorption, increased resistance to abrasion, antifungal activity, easy to clean, resistant to dirt and is used to fill the seams of linings that are used in conditions of periodic moistening and increased hygiene requirements (in bathrooms, showers, kitchens).

Due to the increased content of the CE 40 elasticizer, it can be used:

• on deformable bases (on chipboard and gypsum boards);
• on bases subject to significant temperature fluctuations (heated floors, balconies, terraces, outdoor pools);
• at the device of facings from porcelain tile, a natural stone and glass.

Specifications

Foundation preparation:

Filling the joints of the tiled cladding should be done only after the expiration of the period specified in the instructions. If a traditional cement-sand mixture was used to fasten the tiles, the joints can be filled no earlier than 7 days after laying the tiles. Tiles should fit snugly to the base. The base and tile adhesive must be dry. The edges of the joints must be cleaned of tile adhesive, as well as dust, grease and other contaminants that prevent the adhesion of the grout.

When filling the joints of matte, rough or unglazed tiles, it is necessary to test the color of the tiles with the pigments contained in the grout.

Execution of works:

To prepare the grout mortar mixture, an accurately measured amount of clean water is taken (from + 15C to + 20C). The dry mixture is gradually added to the water with stirring. The preparation of small amounts of the grout mortar mixture is done manually, and significant amounts are made with a mixer or drill with a nozzle for viscous substances. The rotation speed of the stirrer should be 400-800 rpm.
Stirring is carried out until a homogeneous and uniform mass is obtained. Then, a technological pause of 5 minutes is maintained for the maturation of the mortar mixture, after which it is stirred again. The mortar mixture must be used up within 2 hours from the moment of preparation.

An overdose of water leads to a deterioration in the technical characteristics of the grout. The use of rusty tools is not allowed.

The mortar mixture is applied with a rubber spatula to the surface of the cladding and gently rubbed into the seams, moving the tool at an angle of the plane. The excess mortar mixture is collected with a spatula from the surface of the tiles and the operation is repeated again. After about 15 minutes, the treated surface is gently wiped with a damp, often rinsed sponge.

Do not excessively moisten the sponge and intensively wipe the surface of the cladding, as this leads to blurring of the filled joint and discoloration of the grout.

The dried plaque remaining on the tile can be easily removed with a dry soft cloth.

Technological passage through the tiled lining is possible 8 hours after filling the joints, and the first contact with water after 24 hours. During the first 5 days, only contact with clean water is allowed, without the use of any detergents.

Grout consumption depending on the width of the joint and the size of the tile

Shelf life: in dry conditions, on pallets, in original undamaged packaging - no more than 24 months from the date of manufacture.

Attention:

The manufacturer is not responsible for non-compliance with the technology when working with materials, as well as for their use for purposes and conditions not provided for in this technical description.

If in doubt about the applicability of the material, you should test it yourself or consult us.

This technical description, as well as unconfirmed written recommendations, cannot serve as a basis for unconditional liability of the manufacturer.

Works should be carried out in dry conditions, at air and ground temperatures from +5C to +30C. All quality indicators and recommendations set out in the technical description are correct for an ambient temperature of + 20 ° C and a relative humidity of 60%. In other conditions, it is possible to change the setting time and curing of the grout.

To ensure color uniformity when working on the same surface, it is recommended to use materials from the same lot.

Different absorbency of the side edges of the tiles, uneven drying of the joints, excessive moisture content in the base can lead to a difference in the color of the grout in the joints of the cladding.

During outdoor work, the tiled lining after filling the joints during the day should be protected from precipitation.

The dry mix CE 40 contains cement and reacts with water to an alkaline reaction, so it is necessary to protect the eyes and skin when working with it. If the mixture gets into the eyes, rinse them with water and consult a doctor.

Packing: 2 kg.

RECOMMENDATIONS ON CRITICAL FACTORS FOR APPLICATION OF CEMENT GROWS

1. Before grouting, make sure that the substrate and tile adhesive are dry and that moisture cannot enter from the side of the substrate. After applying the tile adhesive, a time period of at least that specified by its manufacturer must elapse.

2. Works should be carried out at a temperature of the base and ambient air not lower than +5°C and not higher than +30°C and relative air humidity not higher than 80%.

3. For outdoor work, the cladding must be protected from precipitation, wind and direct sunlight. During interior work, drafts, uneven heating and early contact with water should be excluded.

4. The joints must be completely cleaned of tile adhesive to the full depth. The ends of absorbent tiles must be moistened evenly.

6. Gradually add the dry mixture to the water while stirring, achieving a homogeneous mass without lumps. Mixing of all brands of grout should be done only with a mixer or a drill with a nozzle at a rotation speed of 400–800 rpm. Pause for about 5 minutes for the mixture to mature and mix it again.

7. In the case of facings made of matt, unglazed tiles, natural or artificial stone, before starting work, test the color of the tiles on a small, least visible area of ​​the facing.

8. Carefully fill the joints with grout using a rubber spatula. Gather excess from the surface with the same spatula, moving it diagonally to the seams

9. Once the grout has thickened (approximately 15 minutes), gently wipe the surface of the cladding with a slightly damp, well-wrung and frequently rinsed sponge, while shaping the surface of the joints. Avoid too early, long and intensive troweling and excessive wetting of the joints, as this leads to blurring and discoloration of the grout!

10. Remove dried deposits from the tiles with a dry soft cloth no later than the period specified by the manufacturer for each specific type of grout. Failure to comply with the deadlines may lead to permanent contamination or damage to the tiles!

11. After completion of work, contact of the grout with water should be excluded, as well as cleaning of the cladding using detergents, within the time specified by the manufacturer for each specific type of grout

When laying tiles in the kitchen, in the bathroom or when creating ceramic cladding on the street, you need to take care of the surface finish - grouting. This will help protect the tile from moisture and prolong its life. It is for these purposes that the cement-based Ceresit CE 40 grout is intended, which is characterized by frost resistance and water-repellent properties. Further in the article, we will consider the scope and color palette of grout from Ceresit.

To work with this grout, the width of the joint should not a exceed 10 mm.

Scope of grout Ceresit CE 40

Due to its excellent performance, the mixture can be used for outdoor and indoor work on vertical and horizontal surfaces. This can be filling joints in ceramic or porcelain stoneware surfaces, facings made of natural stones, such as marble, granite and others.

High elasticity allows the grout to be used even on deformable substrates, such as chipboard, drywall, DSP. Ceresit CE 40 is also suitable for underfloor heating systems, terraces and other substrates that are subject to rapid temperature changes.

In the photo - grout ceresite ce 40

Modifiers for water resistance and antifungal properties - Aquastatic and MicroProtect, respectively, allow the grout to be used for rooms with high levels of humidity. For example, bathrooms, showers and baths. The joint filler is not superfluous on the street either: it can be used for building facades or tile coverings near the pool.

The manufacturer produces other products. Read about what a primer is good for.

Contraindications for use: the mixture is not suitable for fillet and expansion joints, as well as those adjacent to plumbing. For these purposes, silicone fillers are more suitable.

Specifications

Color palette

The palette of the mixture includes 30 colors, which allows you to choose the tone for any tile. Popular colors are white, gray-blue, dark blue, chili, caramel, anthracite, sugar.

Estimated costs can be found below:

Fact: the specific consumption of the mixture during work depends on the width of the seam, the size of the tile, as well as the general qualifications of the master.

User manual

After laying the tiles, it is necessary to withstand a technological pause. The specific time depends on the adhesive or cement-sand mixture used. For the latter, the exposure period is 7 days. After this time, you can proceed to the preparation and filling of the seams.

The quality of the result is directly affected by the presence of moisture, grease, cement and other contaminants on the tiles and edges. All this must be wiped off the lining before grouting. It is recommended to dampen the edges of the tiles with a damp cloth or sponge.

How to breed

It is necessary to dilute Ceresit CE 40 grout in water having a temperature of 15-20 0 C. It is necessary to strictly observe the recommended proportions, alternately mixing the dry mixture with the liquid. If the mixture is small, then manual mixing is allowed. To create large solutions, it is recommended to use a construction mixer or a drill with a special nozzle. The optimal number of revolutions is 400-800 per minute.

On the video - dilution of the grout Ceresit ce 40:

The result should be a homogeneous mass without lumps, which should be infused for 5 minutes. After that, the solution must be mixed again. To achieve a uniform color result on tiles, it is best to use grout from the same batch.

Important: after preparing the solution, it must be used within 2 hours.

How to apply on tiles

To apply the grout, you will need a rubber spatula, which should capture a small amount of the mixture from the container. When filling the joints, it is necessary to collect excess mixture from the tiles and apply them to the unfilled places. Work with grout should be even, applying medium force to fill.

After wiping all the seams, you need to wait 15 minutes and wipe the surface with a damp sponge. Excessive moisture can cause a difference in the tones of the grout, so the sponge must be squeezed out well.

On the video - the use of grout Ceresit ce 40:

After filling the seams and wiping them, it remains to remove the dried plaque, which must be done no later than 8 hours from the moment of grouting. The same period for the technological passage. You can walk on the tile one day after filling. During this time, it is necessary to protect the grout from drying out, moisture, wind, sunlight and mechanical damage. Moisture is allowed no earlier than 7 days after application.

Important: if the tile is located outdoors or in conditions with an open source of water, then it is necessary to cover it for 7 days until the solution has completely set.

Price

The cost of grout Ceresit CE 40 is 370-590 rubles. It all depends on the packaging, the chosen color and the offer of a particular store.

But where you can use epoxy grout for litokol tiles, this will help you understand

What is the price of grouting tiles in the bathroom and which one should be used and what name will help to understand the content in this

But how to use a moisture-resistant grout for tile joints in the bathroom and what is the consumption of this material when used, this will help to understand

Ceresit CE 40 Aquastatic grout is designed for joints up to 10 mm wide. It is water and frost resistant. It can be used for grouting joints in the bath along with such grouts as Ceresit CE 35 Super.

CE 40 Aquastatic - elastic water-repellent grout
for joints up to 10 mm

• available in 30 colors, including white;
• has an enhanced antifungal effect (Trio Protection "Micro Protect" formula);
• water-repellent (Aquastatic effect);
• resistant to dirt, easy to clean;
• elastic, resistant to deformation;
• has a high color fastness;
• perfectly smooth;
• water and frost resistant;
• can be used on underfloor heating;
• suitable for indoor and outdoor use;
• environmentally safe.

Application area

Grout CE 40 Aquastatic is intended for grouting ceramic, stone (including marble) and glass facings on floors and walls inside and outside buildings, with a joint width of up to 10 mm. Due to its high elasticity, the grout can be used on deformable substrates (chipboard, chipboard, drywall, etc.) and substrates subject to temperature fluctuations (heated floors, terraces, outdoor pools, etc.).

Thanks to the Aquastatic effect (hydrophobic properties) and the MicroProtect formula (high resistance to fungus and mold), CE 40 grout is optimal for use in rooms with constant humidity: bathrooms, showers, kitchens, etc.

It is recommended to fill corner, deformation and seams adjacent to sanitary equipment.

Foundation preparation

The grouting of tiled cladding joints should only be carried out after the expiration of the period specified in the instructions for the adhesive used. If a traditional cement-sand mixture was used to fasten the tiles, the joints can be filled no earlier than 7 days after laying the tiles.

The base and tile adhesive must be dry. The edges of the joints must be cleaned of tile adhesive, as well as dust, grease and other contaminants that prevent the adhesion of the grout. It is recommended to moisten the edges of the tiles with a damp sponge. When grouting existing tile facings, the old grout must be completely removed.

In the case of matte, unglazed or stone tiles, it is necessary to test the color of the tiles with the pigments contained in the grout.

Execution of work

To prepare the mixture, take a measured amount of clean water with a temperature of +15 to +20 ° C. The dry mixture is gradually added to the water with stirring, achieving a homogeneous mass without lumps. Mixing must be done with a mixer or a drill with a nozzle at a rotation speed of 400-800 rpm. Then, a technological pause is maintained for about 5 minutes to mature the mixture and mix again. The ready-to-use mixture must be used up within 2 hours of preparation.. An overdose of water leads to a deterioration in the technical characteristics of the grout!

The joints are filled with grout with a rubber spatula, collecting excess from the surface with diagonal movements. After about 15 minutes, the surface of the lining is gently wiped with a damp, well-wrung out, often rinsed sponge. Excessive wetting of the seams can lead to uneven tone!

Dried plaque from the tiles is removed with a dry soft cloth no later than 8 hours after grouting. Technological passage is possible after 8 hours, and the first contact with water - 7 days after filling the joints.

• Works should be carried out at air and substrate temperatures from +5 to +30°C and relative air humidity not higher than 80%.
• High humidity of the base, different amount of mixing water, uneven drying and too intensive smoothing of the seams can lead to uneven tone. In order to avoid differences in the shades of the joints, it is recommended to use the grout of the same batch on the same plane.
• When working, use tools made of stainless materials.
• Within 24 hours after filling the joints, the grout must be protected from drying out (protected from direct sunlight, wind, heat, etc.), and within 7 days - from contact with water (for outdoor work, provide protection from rain).

Shelf life

In dry conditions, on pallets, in original undamaged packaging - no more than 24 months from the date of manufacture.

Package

Dry mix CE 40 Aquastatic is supplied in 2 kg plastic pails.

Specifications

Color range CE 40 Aquastatic

The product contains cement and when interacting with water gives an alkaline reaction, therefore, when working with it, it is necessary to protect the eyes and skin. If the mixture gets into the eyes, rinse them with water and seek medical attention.

In addition to the technical description, when working with the material, one should be guided by the relevant building codes and rules of the Russian Federation. The manufacturer is not responsible for non-compliance with the technology when working with the material, as well as for its use for purposes and conditions not provided for in this technical description. If in doubt about the suitability of a particular application of a material, you should test it yourself or consult the manufacturer. The technical description, as well as recommendations not confirmed in writing, cannot serve as a basis for the unconditional liability of the manufacturer. With the advent of this technical description, all previous ones become invalid.

When renovating a bathroom, two colors of grout were used to finish the tile joints - light (on the top of the wall tiles) and brown - for the floor and the bottom of the wall tiles). Light decided to take Ceresit CE 40 water-repellent, for the dark one they used Fugue KIILTO (grout for joints of wall ceramic tiles and tiles). Initially, they wanted to take both colors only Ceresit, since it seems that the brand is always well-known, has established itself in the market and in the previous repair, which we did 12 years ago, also used Ceresit. But on the advice of a consultant, we decided to take a slightly more expensive Finnish KIILTO for a sample for one of the flowers. Too bad there's only one.

The first disappointment Ceresit CE 40 befell when we prepared the grout mixture (diluted according to the manufacturer's instructions) - color does not match palette. Since our upper part of the wall tile was not pure white, but rather cream, we chose the jasmine shade for the grout according to the palette in the hardware store. We compared the color both on a paper palette and on probes, like these.

It is clearly seen that the shade of "jasmine" is not blindingly white, but calm milky, which was exactly what was needed. And here is what we got as a result.

In fact, the color of the grout is more like “caramel” or “peach”, which in the end looks like a dirty seam with our tiles. Also, the color of the grout was uneven, no matter how much we knead it, when filling the seams, a red pigment still climbed out somewhere and stretched out with a “dirty” strip.

The texture of the grout is bad - viscous, does not go well into the seams, reaches for the spatula. When the moment comes (according to the instructions again), wipe it with a damp sponge to remove excess - it still reaches for the sponge. If you overdo it a little - the excess dries right on the tile and removing them from it is another "pleasure". As a result - humpbacked, uneven and "multi-colored" seams.

And here are the seams made with KIILTO grout. The difference is obvious.

Also, in some places, after 3-4 months, cracks appeared on the Ceresit grout.

But that's not all of her flaws. In our bathroom, like in any other, there is condensation. In order for the walls to dry faster, we installed an artificial draft fan that turns on with the light. At one time, after bathing, I wiped the walls with a moisture-absorbing napkin. About a year ago, we moved and our parents live in this apartment, and they don’t always want to wipe the walls every time after bathing, especially since the fan is running. And now, 2 years after the repair, mold spots appeared ONLY ON Ceresit GUT. The grouting technology was maintained, everything was according to the manufacturer's instructions. After grouting the joints in the bathroom, they did not bathe for another 4 days in order to play it safe and prevent moisture from entering.

If it were not for the fugue from KIILTO, I would still consider that such a problematic application and mold on waterproof (!!!) grout is the norm. Because in the past bathroom renovation, parents also used Ceresit grout, and then mold spots also appeared. But then we had a shower stall, and the humidity in it went through the roof, everything was written off on it.

BUT here is a visual photo, where the "shock" wall is visible, on which the main moisture falls (water from the shower pours onto it). Everything is fine with KIILTO grout. Although it is dark, but if there was black mold, whatever one may say, it would be visible.

And in the work of KIILTO was simply divine, the price at the same time is slightly more. I recommend giving preference to her, and stay away from Ceresit CE 40).

Happy repair!

I hope it was useful))))