How to make a crossbow from a wooden clothespin. How to make a matchstick from a clothespin. Crossbow from a clothespin or Matchshot

Nowadays, you can buy almost any children's toy in the store, although their quality and usefulness are very doubtful. And Soviet schoolchildren often made their own toys. For example, a matchstick. This homemade shoots not far, but it is made quite simply.

To make a matchshooter, you will need a thin felt-tip pen and a powerful spring. By the way, the spring can be removed from the lighter. Or from the mechanism of an automatic ballpoint pen.

Using a hacksaw, cut the felt-tip pen into two equal parts. Then remove from it the writing tip, core, and plug, which is located on the top of the felt-tip pen.

Insert a small metal (or plastic) plate into the spring. This must be done so that when using a matchbore, the match does not fall inward.

Take the bottom of the marker and place the spring in it. Close the top tightly with the cap.

So, the matchstick is ready. To start using it, insert a match into the hole, press it with your finger and release it sharply. The spring will unfold and push the match out. The firing range of this homemade product is about five meters and entirely depends on the length and elasticity of the spring.

You can not be afraid to make a matchshooter for your child, because the joint production of any craft is a great pastime, and a ready-made matchshooter will be no more dangerous than a gun bought in a store that shoots plastic or rubber bullets, because matches in this case are not used for their intended purpose and they can remove the sulfur head. A matchgun can be made from a variety of improvised means and materials, and in this case we will make it from a clothespin.

TO MAKE A MATCHBOOT FROM A LAUNDRY PEGS YOU WILL NEED:

=>Knife,
=> Clothespin,
=> Narrow tape or spool of thread.

SELECTING A CLOTCH FOR MANUFACTURING A MATCHBOOT

Not every clothespin is suitable for making a matchstick, and it doesn’t really matter if it is plastic or wooden. It is important to take a clothespin for a matchbox that has a certain design. Clothespins with a spring inside used as a spacer and something like that will not work.

For a matchshot of this option, you must use a clothespin with a spring that does not burst from the inside, but the pressing part of the clothespin from the outside. Such a spring will be used as a trigger and a mechanism for pushing a match out of a match gun.

MANUFACTURING A MATCHBOOT FROM A LAUNDRY PEGS

After we have found a suitable clothespin for a matchbore, we will proceed to its manufacture.

1. Let's disassemble our clothespin in parts, into a spring and two blanks.

2. On the outside of one part of the clothespin, cut a groove with a knife or other sharp cutting tool.

3. In the other part of the clothespin, we make exactly the same cutout and now you can connect both elements of the matchstick and see how it will look.

5. Now we have to choose one of the blanks for making two more cutouts, for which the spring from the clothespin for shooting will be attached. We make external and internal transverse cuts and proceed to the sixth stage of manufacturing a matchstick.

6. At this stage, along one of the parts of the workpiece, we cut a channel for loading and firing the match arrow with matches.

7. In another blank, we make exactly the same channel.

9. At this stage of work, with the help of adhesive tape or threads, we fasten both blanks and get a ready-made matchgun, but without a trigger and a trigger.

10. In order for our matchstick to fire a shot, we equip it with a spring that was pulled out of the clothespin at the very beginning.

12. We stretch the spring and fix its edges into the notches previously cut across. We insert a match and you can shoot from a match gun.

13. After pressing the trigger, the inner part of the spring will pop out of the recess and push the match out of the match gun.

In order for the match shooter from the clothespin to shoot again, we stretch the spring, load it with a match and pull the trigger.

Every grown man was once a child. And the greatest entertainment in those happy times of childhood was to play with friends in the yard. It doesn't matter what, the main thing is to play. What did you play most often? Of course, in skirmishes, war, guerrillas and much more, it was impossible to list everything. And if there was an opportunity to shoot from something, then it was the ultimate dream of any boy! Slingshots, crossbows and other charms of the world of boys simply excited the imagination. And if something is blown up to the whole yard, then this is the height of bliss! And if it is possible to shoot burning matches at a decent distance? It was, as they say now, "The Hit of the Season"! We will tell you about one of the types of boyish fun. It's called scarecrow.

A pugach is a device that makes noise. The main purpose of its creation is to scare someone. In fact, a scarecrow is considered to be a children's toy in the form of a pistol, which, when used with caps, makes a loud popping sound. But there are also so-called "adult" pugachi - blank cartridges, for example.

However, there are also many ways to make a scarecrow at home. What can this product be made from?

1. from a copper tube and a piece of plywood;
2. from a clothespin;
3. from a metal tube;
4. from a bicycle spoke;
5. from two bolts and a nut;
6. from a dowel, etc.

Show all

A pugach from a clothespin, or, as it is also called, "Matchshot", was invented a very long time ago, when the Soviet Union still existed. A whole era of children have been amused by this kind of "weapon" when playing war with friends in the yard. The design is so simple, and the materials for its manufacture were so accessible to everyone that only the lazy or those who had not heard anything about it did not make a clothespin scarecrow. Compactness, ease of use and reliability have made the device very popular. Another feature is that it was possible to shoot both conventional and incendiary shells from it.

Nowadays, a clothespin scarecrow is no longer popular. One of the main reasons is that in Soviet times, clothespins were wooden with a weak spring, and now they are made of plastic. Another important factor: now children have so much entertainment (the Internet, games, movies) that they are not even interested in doing something with their own hands. And with the development of the Internet and social networks, you rarely see school-age children in the yard who would play something.

However, there are still enthusiasts! For them, we wrote this article, in which we will tell you in detail how to make a scarecrow from a clothespin with your own hands. So let's get started.






Now let's go directly to the description of what needs to be done to create this miracle weapon.

First stage

You disassemble the clothespin into three parts - you should get two of its wooden bases and a spring.



Second phase

Using a penknife, it is necessary to process both halves of the base of the clothespin, which is not at all difficult. First, cut a gutter on one of the wooden bases. Don't rush or you could cut your fingers! Then divide the second half into two parts.



Third stage

Now carefully pull the spring back to the chute so that its protrusion fits exactly into the chute. Then you need to attach the short part to the long one. In order to avoid mistakes, you should focus on the factory gutter. The final stage: when everything has risen as it should, it is necessary to fasten all the details with an elastic band. Everything is ready! As you can see, making a scarecrow is not at all difficult!



The next thing to do is to test our creation. This is the most enjoyable stage, isn't it?

Checking the product

To do this, perform the following steps:

1. 1. Pull the upper part forward until the spring is its protrusion in the factory chute. Once you have done this, you must pull this part back until the clothespin with its protrusion is in the groove that you made.
2. 2. Now you must select a projectile and load it. To do this is simple: slightly lifting the top part. In this case, matches or paper clips are best suited as shells.
3. 3. Then we retract the spring until the start bar is released. After that, there should be a shot. If so, cheers! You did everything right!

What to do if the device does not work?

The reason may be the fact that the second part of the spring is not held in place. What should be done? It is necessary to deepen the groove in which the spring is held.

Believe it or not, even such a simple device can be upgraded! Yes, yes, don't be surprised. Now we'll tell you how.

Glue a strip to the bottom of the scarecrow, which we cut out of the matchbox. We cut out a fragment where sulfur is located to set fire to matches. As a result of this improvement, the match will light up at the moment of the shot.

Safety precautions for use

Since the range of the projectile can be up to five meters, never use it at home or in other areas. Also, do not aim at other people, children or animals. Also keep your crossbow away from flammable objects. It is highly advisable to wear goggles to protect your eyes when using burning shells, caution does not hurt. Happy use!

A matchstick from a clothespin was invented back in the days of the Soviet Union. He was also called "pugach" in the common people. Schoolboys gladly used this "weapon" in their battles. Due to the simplicity of design and components that are always available, the crossbow was very popular among students in high and low grades. Everyone knew how to make a scarecrow. This device is compact, and you can shoot from it with both conventional and incendiary ammunition. It depends on individual desire. Although firing fire projectiles had more of a psychological impact, as it also caused physical harm. The effectiveness of such a charge is negligible. Now this weapon has lost its former popularity. To a certain extent, this was influenced by the fact that now clothespins are mainly made of plastic, and wooden ones have a very weak spring. Yes, plus to this, the kids are now lazy and not particularly hardworking. But still there are still real connoisseurs of this uncomplicated weapon who would like to know the process of its manufacture. Here for them further it will be told about how to make a pugach with your own hands. In the hope that they will pass on this secret to others, as a result of this it will not be lost.

Fixture base

How to make a pugach from a clothespin - a children's weapon from the times of the Soviet Union? The answer to this question is quite simple. Some people still use wooden clothespins.

One of them can be taken as a basis in the manufacture of this throwing weapon, which can shoot lit matches like a real military weapon.

improvised materials

In this case, the following is required:

1. Clothespin made of wood.
2. Elastic.

Instruments

Here you will need:

1. Penknife.
2. Protective glasses.

Ammunition

In this regard, you can use:

Manufacturing process

Now let's move on to the question of how to make a homemade scarecrow.

For this you need:

Disassemble the clothespin itself into three parts. Namely: two halves of wood and a metal spring.

With the help you need to finalize both halves. It is not difficult to do this. First, you just need to cut a small groove on one of the wooden halves. Take your time, your fingers are much more valuable than any clothespin. Then divide the second half into two parts.

Then the spring must be pulled back to the indicated groove. This must be done carefully. So that her protrusion enters this very gutter.

Then attach the short piece to the long one. In order not to make a mistake during assembly, before making a scarecrow, be guided by the factory grooves. After everything fell into place, you need to fasten the elements with an elastic band. That's all. The pugach from the clothespin is ready.

Remember that the indicated wooden parts tightened with an elastic band should still move apart a little. That is, so much so that the upper part makes it possible to cock the spring.

Check for "combat readiness"

In the question of how to make a bugger, it should be taken into account that this device must be ready to fire. That is, you need to check. To do this, you need to perform the following steps:

1. Pull the top forward. Until the protrusion of the spring is in the factory groove on its surface. When you achieve this, then pull this part back. Until the moment when the protrusion of the clothespin is in the groove you made at the bottom of the matchbox.
2. Then select a projectile and load it by lifting the top part of this device. In this case, ordinary matches or metal paper clips are ideal.
3. After that, pull back the spring so that the starting bar is released. This will result in a shot. That is, the device works.

Cause of malfunction

It may also be that the matchgun will not shoot. This may be due to the fact that another part of the spring is jumping out of place. Then you have to further deepen the groove into which it enters. This malfunction appears from the fact that the depth of the groove is not the right size.

Fixture upgrade

In the future, you can improve your scarecrow. To do this, glue a fragment of a matchbox on which sulfur is located to its lower part. It's easy to do. After such an upgrade, the matches will light up when fired. This will add additional efficiency to this device. Also, part of the matchbox can be completely replaced with a piece of sandpaper. However, in this case, you will have to insert the matches into the pugach back to front. It won't be very convenient. This problem is much easier to solve by lighting matches before firing. In this case, do not neglect the danger posed by burning shells. Never use them indoors, do not shoot at flammable objects and it is advisable to wear them at the same time. And of course, in no case should you aim at people and animals. The matchgun is capable of shooting at a distance of up to five meters, and sometimes even further.

Conclusion

After reviewing the foregoing, everyone will be able to figure out the question of how to make a matchstick gunner. It is only necessary in this case desire, scrupulousness and diligence.