How to build a coffee table with your own hands. Do-it-yourself modern coffee table: drawings and design description. New life for old things

The living room will look empty if it does not have a chipboard coffee table or other suitable material. If you wish and have free time, you can make a coffee table with your own hands. The recommendations below will help with this, as well as drawings of coffee tables. If you plan to fly a coffee table with your own hands, then you can easily find suitable drawings here.

Drawer table Metal table Transforming table

To make a coffee table with your own hands, you will need:

  • hardboard slab or plywood, if you are going to create a plywood coffee table with your own hands or a transformer coffee table;
  • boards;
  • tape measure, which will help determine the size;
  • a hammer;
  • grinding machine;
  • 3-4 legs. If your plans include a round coffee table with your own hands, then you should take 3 legs;
  • hacksaw for woodworking;
  • drill and a set of drills;
  • screws, self-tapping screws, finishing nails;
  • putty and high-quality glue;
  • paint and primer;
  • sandpaper.

You may need additional tools, it all depends on what kind of coffee table you intend to make.

How to make a coffee table?

You can create a tea table with your own hands by following the scheme:

  1. Cut the ends of the boards at an angle of 45º, cut out elements from wood material or chipboard, the length of which will be equal to the length of the blanks made.
  2. Place the parts in the center, carefully align the ends.
  3. Take measurements to determine the distance separating the extreme bars. Using the parameters obtained, cut out a pair of blanks that will be used as the lower supports. Fasten them with screws. Screw fasteners into each longitudinal rail to give the table strength and stability.
  4. Drill a couple of holes at the ends of the support rails, which will be useful for integrating the structure with other elements. If you do not have enough experience with the tool, practice by taking unnecessary wood trimmings.
  5. Place the workpieces on the sides, secure with a quick-clamping device called a clamp. Masters who create a coffee table from chipboard or from softwood (pine solid wood) do this: they put board trimmings under the fastener supports. By doing so, they avoid marks left on the surface.
  6. Firmly fix the extreme bars on the base, screw the screws into the holes made in advance.
  7. Take measurements to find out the width of the base made (this is necessary in order to understand how long the blank for the end part should be). Experts say: “I assemble a thing with an accuracy of a millimeter, because I take a sip with a small margin in length, and carefully grind off the extra centimeters.” When making a wooden coffee table, use the advice.
  8. Moisten the end parts with water, apply adhesive, assemble the individual parts. Make a belt. This will allow you to fasten the structure together and fix it in a certain position. For a stronger bond, use carnations for finishing work.
  9. Process the assembled coffee table with sandpaper with your own hands, removing irregularities. The gaps formed at the site of the seams must be filled with a putty mass.
  10. Color the assembled coffee table, made by yourself, using the finished project.
  11. Place mounting plates on the lower crossbars of future coffee tables, which will later be useful for making the lower part. Make holes and screw the legs into them.

Do-it-yourself transformer coffee table is a little more difficult to make, however, the coffee table assembly scheme is approximately identical.

A transforming table, made from improvised materials with your own hands, will complement the room and make it more functional. Transformer for the living room - this is optimal for the room.

1 2 3

As you can see, making a coffee table made of wood with your own hands is not as difficult as it might seem at first glance.

DIY coffee table on wheels

1 2 3

If desired, you can assemble a table from chipboard with your own hands on wheels. A folding coffee table is very convenient to use, as it allows you to move furniture from place to place without any extra effort. An original coffee table with your own hands is quite a feasible task. Make a lunch option according to the algorithm presented above, and then fix the wheels on the legs. You can remove this part from an old cart and equip a dining or stylish folding table from boards for magazines or other accessories.

To fix fixtures at home, use high-quality screws. Attach the wheels to the base of the structure, making sure that they do not peek out from under the bottom. It is unacceptable that the plinth makes it difficult to move the homemade table. Adjust the location that the coffee table will occupy: low or high level of supports. It is important that the wheels turn without difficulty, allowing you to move the table.

DIY glass coffee table

Tables with glass are very presentable and practical. The transparent top is perfectly combined with various types of materials. To make a coffee table out of wood with a glass top, decide how thick the glass needs to be and choose the appropriate method for cutting it.

To make a glass coffee table with your own hands, you will need a furniture board in which a hole of the desired shape is cut. Next, you need to fix the pre-cut glass in it (for this purpose it is most convenient to use a glazing bead). In the presence of a glass cutter, it is better to use this particular device, which ensures high-quality work.

There are two main types of glass cutter: roller and diamond type. Devices of the first type are suitable for working on a thinner glass plate, whose thickness is not more than 4 cm. The tool includes from 1 to 6 rollers. There must be a cut line. Experts say that models with an oil reservoir have the best properties. They are great for both professionals and beginners.

Carefully prepare the glass before cutting, that is, rinse it and degrease it. If you are dealing with a relief surface, then a diamond glass cutter is absolutely not suitable for working on it. Cut such a plate, turning the smooth side towards you. When cutting with a roller glass cutter, make sure that the line is completely covered with turpentine liquid.

After the glass has been cut, fix it using special glue. If there is no adhesive composition available, it is allowed to use suction cups for making Provence-style furniture with your own hands, which are attached first to the leg and then to the glass.

If desired, the table with your own hands can be decorated with a variety of decorative elements, which will make it even more presentable and modern. View a photo or video on our website to understand how best to arrange a table on wheels. If you don’t understand some details, ask the experts how to make a coffee table with your own hands.

Choosing a coffee table. Advantages and disadvantages of each material. Which table to choose for your interior? Do you need shelves and drawers in a coffee table? Photo ideas for inspiration: a transforming table. We make a coffee table with our own hands.

Material choice, pros and cons

The coffee table is considered the most functional and versatile piece of furniture in any interior. It is present in almost every living room. Often it can be found in. The coffee table will fit even on yours if you like to sit there reading or working on the computer. With its help, the space will become more comfortable and aesthetically more beautiful. We will tell you what types of coffee tables are divided into, what materials exist for their manufacture, as well as the pros and cons of each.

Coffee tables are subdivided
Classification:Classification characteristic:

By form;

Height;

According to the material from which the frame is made;

According to the material from which the countertop is made;

Depending on the mode of travel;

Depending on the presence of a folding mechanism.

Circle, oval, square, rectangle, triangle, polygon, arbitrary (unusual) tabletop shape;

The average height of an ordinary coffee table does not exceed 50 cm (however, there are models of lower and higher tables);

Wood (snag, stump), glass, metal (forged products), plastic;

Wood, chipboard (laminated), “wickerwork” (vine), fabric or leather upholstery, tempered glass (including tinted glass), plastic, veneer, metal sheets, mirror surface, stone, mosaic;

On wheels (mobile) and without (stationary);

Tables-transformers or ordinary.

The coffee table is considered the most functional and versatile piece of furniture in any interior. It is present in almost every living room. Often it can be found in a spacious bedroom.

from wood

Wooden coffee tables are the most popular option that can easily fit into almost any interior. It is enough to choose a shade that will be in harmony with the rest of the furniture in this room. It is desirable that the decoration of such a table was made in the appropriate style.

From glass

Decorating their home in a modern style, people began to pay more attention to models of coffee tables made of glass. They look quite "airy" due to their transparency. Nevertheless, the most unusual materials can be selected as a support at such tables - tree snags, deer antlers, corals and others.

metal

The metal is difficult to process, which is why the models of such coffee tables are expensive. They are also heavy in weight, which makes it difficult to move them around the room. But they are durable, they are not afraid of any damage.

Choosing a coffee table depending on the overall style of the room

Look at the examples of interior design, including the presence of a coffee table, in the catalog - you can see how diverse they can be (in form, materials, decor elements and purpose):

When choosing a coffee table for the living room, clearly consider what “duties” you assign to it.

Classical

The most ordinary small coffee table made of wood will best fit into the classic interior. An exception can only be the bright decor of the base and legs of the table, matched to match all other pieces of furniture and decoration. It is very important in such situations to take into account the careful selection of wood tones so that the furniture looks like a single set.

Provence

Pastel shades of furniture, including naturalness (unpainted wood), are considered a feature of the Provencal style, carved legs at tables and antique design (artificial aging) are no less popular. For example, coffee tables that are massive in size will fit better in a large living room. But for a small room, small models are ideal. If you prefer French style, then these tables are for you:

Country

Most ethnic styles (by the way, which include country music) amaze with original ideas and unusual use of the most ordinary materials. Some surprise with bamboo models, others with multi-colored complex mosaics made of small shells. Country, on the other hand, is able to accept a table made of roughly hewn wood or logs into its interior. Also in appearance, models of this style are represented by the roughness of the surface of unpolished wood. See for yourself:

Modern

Where there is truly no end to the design fantasy, it is in a modern style. Fortunately, materials for the manufacture of such coffee tables can be found everywhere - wood, stone, glass, metal, plastic. The most important thing is to observe the conciseness of forms and lines. A little creativity and a unique coffee table will appear in your interior.

Pop Art

The main task of the pop art style is to remake ordinary things into something from the realm of fantasy. By creating such “works of art”, this style allows you to transform the gray everyday life with bright decor elements. Coffee tables are no exception. Designers do not spare inspiration, I improve existing simple things.

Loft

The presence of rough metal details and rough-hewn wood, as well as the creation of a peculiar kind of "street furniture" - this is all loft style. It is original and brutal. At the same time, everyone likes it without exception. If you see a coffee table resembling a cart, know this is also a loft. Many ideas came to the minds of designers when they visited "specific" places - semi-abandoned old factories and manufactories, it was there that they drew their inspiration.

Coffee table-transformer

When choosing a coffee table for, clearly consider what “duties” you assign to it. If you need a decorative element of the interior, then take a closer look at the tables of an unusual shape, which are often offered by various designers. However, if you want to get not only a coffee table, but also a dining or computer table in one person, then you should look at folding models -. With some effort, in just one minute, you can turn your nondescript coffee table into a full-fledged dining area for several people. Isn't that what you dreamed of?! It is great if such a model is on wheels - this will facilitate the movement of the table around the room.

DIY transformer table:

Coffee table as an element of the storage system

Its very name - "magazine" suggests that this table is designed to store magazines, as well as books, newspapers and other small items (remote controls, phone chargers, etc.). In order not to clutter up its surface, most models have shelves or drawers that create additional storage space for the necessary things. Such elements of the storage system will not necessarily be located outside - in front of everyone, they can also be built-in (hidden, secret), which only you will know about. Here are just a few models with original ideas:

DIY coffee table - video and drawings

DIY coffee table
Materials and tools:Working process:

Prefabricated parts made of fiberboard or wood.

2 wheels.

Special glue for wood.

Drill and drill bits for it.

Electric screwdriver, screwdrivers.

Jigsaw, wood saw.

Screws and dowels.

Roulette and level.

Sandpaper or grinder.

Wooden hammer.

We cut out the details according to the drawing.

We make holes for the tongues in a rectangular partition and in the center of the base of the countertop, at an approximate distance of 10 cm.

Now, at a height of 36 and 48 cm, we make 2 holes on the partition itself for the subsequent fixing of 2 semicircular shelves on it.

You can install dowels. We assemble the table, after making sure that the overall structure is even. We disassemble it again and make several holes in rectangular blanks (36, 48, 23 cm).

We proceed to the final assembly. To do this, we sequentially assemble - the base, the central and lower partition, semicircular shelves, the upper partition and the tabletop itself.

We assemble with a wooden hammer and tongues, planted on glue.

We complete the assembly process by attaching the wheels to the screws (during the subsequent movement of the table, they should not touch the base). Everything - the table is ready!

We invite you to watch a few videos with vivid examples of original coffee table models that you can make without leaving your home.

The coffee table is an optional piece of furniture. At the same time, its presence makes any living room more comfortable. On the table you can put a newspaper, put a cup of tea or coffee. We will make this piece of furniture ourselves, making it truly original and comfortable.

Low table - a practical interior decoration

The very first coffee table was created in the middle of the 19th century in England. Within a couple of decades, this furniture adorned the living rooms of all European houses. In the 20th century, the fashion for it came to our country. True, in Russia the tables we are interested in are called coffee tables, not coffee tables. But this does not change the essence of the matter. Such a piece of furniture is understood as a small table no more than 40-50 cm high, which can have any ergonomics, look and design. It all depends on the preferences of the consumer.

In furniture stores, low tables are sold in a wide range. You can find both an inexpensive design and a designer thing that can make any interior chic and unusual. But many home craftsmen want to make an original table themselves using a variety of improvised materials. We put a piece of our soul into home-made furniture. So, it will turn out really comfortable and will be able to fill the home with comfort and warmth.

Coffee tables are made from wood and glass. It is also possible to assemble unusual and beautiful designs from:

  • an old window and ordinary books;
  • unused heating radiator;
  • wooden pallets or boxes;
  • dismantled interior or entrance door;
  • car tire;
  • wicker basket;
  • coils from the electric cable.

There are a lot of options for making a table for tea parties. You just need to show your imagination and listen to the advice of experienced craftsmen who are engaged in self-decoration of their homes. Next, we describe the most popular ways to build coffee tables. And you stop your choice on the most suitable option.

We make furniture from chipboard - as easy as shelling pears!

Chipboard is the most affordable material to create. Chipboards are processed without problems, easily cut to the required dimensions, and have an affordable price. For the assembly of low tables, it is recommended to use laminated boards, as they are characterized by an attractive appearance, and products from them are durable. There are many sites on the Internet where it is not difficult to find various drawings with dimensions for making furniture from chipboard. We propose to make a table, focusing on the sketches below.

The design we planned consists of the following elements:

  • shelf dimensions 500x700 mm;
  • countertop 736x736;
  • 4 strips 100x464;
  • 4 plastic corners and the same number of legs (or wheels);
  • 2 bottoms (the dimensions of each of them are 500x700);
  • 4 strips 100x464.

We will fasten these elements with cofirmats, they will need 8 pieces, and 16 3.5x16 mm.

We make the table step by step. First (position 1 in the diagram) we make a shelf from a chipboard (preferably, as it was said, laminated) board. Cutting is done with an electric jigsaw, using a file with a small step. Such a tool will eliminate the likelihood of chips. Then (position 2) we attach the planks to the tabletop (we sit them on plastic corners). We mount the shelf (pos. 3) in the center of the strips installed vertically. We make holes in it with a cross section of 4.5 mm (you will need a drill with an appropriate drill). We fix the shelf with confirmations. Without them, our tea table may not be very stable and reliable in operation. With the help of confirmations, we screw the bottom of the structure (pos. 4).

After that, we fasten the legs (pos. 5). They are not fastened from the very edges of the table, but retreated from them by about 15 mm. Instead of legs, it is allowed to mount small wheels (fixed with self-tapping screws). Then we get a mobile coffee table that can be moved throughout the home. It remains only to bring home-made furniture to mind. We glue with a melamine edge all the visible joints of our table. Visually, the design of laminated chipboard will look perfect! By the way, instead of wood chip blanks, you can use MDF (wood fiber products). The result will be about the same.

Glass table - stylish and elegant

The interiors, made in a modern theme, are perfectly complemented by compact glass tables. They are installed on wooden or chrome legs. It is desirable to use frosted glass. It usually has a special film that protects the countertop from mechanical damage. In addition, stains from spilled tea, coffee, other drinks and fingerprints on frosted glass will not be so noticeable.

The recommended tabletop width is up to 120 cm. There is no need to build a table with large parameters. It will be difficult to fit it into the interior of a standard apartment or a small private house. Choose any form of construction. But if you are making a glass coffee table with your own hands for the first time, it is better to stay in a rectangular configuration. We can buy chrome legs in a furniture store. And wood components are easy to make yourself. A drawing of a table with standard dimensions is shown below.

Let's get to work. First, we cut the glass according to the given geometric parameters. This operation must be done slowly. Place the glass on a flat surface. We outline the cut lines with a simple pencil. Wet the glass cutter with sunflower oil (or other lubricant). We apply a metal ruler to the intended line. Gently (without strong pressure) we go through the markup with a glass cutter. Then we shift the glass from the surface, ensuring that the extra pieces of material are on weight. We tap our fingers along the marking line, lightly press. After these actions, unnecessary parts of the glass break strictly along the lines made.

The cut material needs to be processed. First, we clean the edges of the glass with a file, then with a grinder equipped with a diamond tool. Additionally, it is recommended to sand potentially unsafe parts of the glass with sandpaper (fine grit). Then we take a thin felt, mount it on the edges of the countertop and press it against it. This will protect our furniture from scratches. Flip the table face down. We make marks for mounting the legs. From the edges of the tabletop, it is desirable to install them at a distance of at least 50 mm.

We drill holes at the top of the bases of all legs. They will be required to attach the suction cup. Everything is simple here. We process the suction cups with an adhesive, mount them in the prepared holes, press the elements as tightly as possible. After the glue sets, we turn the home-made structure into its normal position and wait about two days. After 48 hours the coffee table will be ready for use.

We will build a structure from wood - a win-win option

Wooden tea tables are suitable for any living space, no matter what kind of decor is implemented in them. Wood products look great both in classic interiors and in the most modern ones. Making wooden furniture with your own hands is really simple. Moreover, we can build a table of any design - the simplest, with many additional drawers, stands, shelves. With the right approach to business, we will get a piece of furniture that is no different from expensive store tables.

We will not offer a drawing of a wooden structure. Any craftsman is able to draw up a simple sketch of such a structure with the desired dimensions. But let's say a few words about the materials and tools that will be needed to complete the work. Stocking up:

  • bars or trimmings of wooden boards (of which we will make table legs and crossbars);
  • two thick boards;
  • varnish and stain;
  • grinder, sandpaper;
  • wood saw;
  • glue;
  • electric drill.

We start creating. We cut thick boards to the required dimensions to make a countertop out of them. We connect them with each other with glue. We are waiting for the structure to stick together firmly. At this time, we make crossbars and legs from scraps of boards or bars. We give the tabletop the selected shape. It can be rectangular or square (it's easier), but tables with a variety of roundness and curves look better. Wood is easy to work with. With the help of a hacksaw, we can easily create a countertop of the configuration we need. After that, using a grinding machine, we carefully process the finished elements. Additionally, we rub their surface with sandpaper.

On the countertop, legs, crossbars we apply stain. This composition gives the tree a noble look, providing the effect of antiquity. These elements are completely processed with a stain. We need to apply it not only on the surface, but also on the end parts of the coffee table parts. Nuance. The ends of wood products can be covered with decorative materials, for example, butterflies often used for this purpose.

Next, we attach the crossbars to the tabletop, assembled from two boards. The operation is performed using glue and round spikes inserted into pre-made holes. The latter are drilled in the right places with an electric drill. We fix the legs in the same way: we make holes, grease the spikes with glue, insert them into the grooves. The tea table is ready. Let's cover it with varnish so that the design looks perfect, and enjoy the new piece of furniture in the house.

Books, waste paper and an old window - you can even make a table out of them!

As we have already noted, the original coffee table can really be made from various improvised materials. If you have a lot of old magazines and newspapers, you don't have to throw them away. Let's make an unusual table out of them according to the following scheme:

  1. 1. We roll waste paper into tight tubes.
  2. 2. We fix the resulting blanks with rubber bands.
  3. 3. Immerse the prepared tubes into a bucket filled with a water-polymer emulsion.
  4. 4. We are waiting for 5-7 minutes.
  5. 5. We take out the soaked paper blanks and hang them on a rope on wire hooks. Drying should be carried out in a room where there is no dust. Don't forget to put plastic wrap under the rope. Streams of water from waste paper will flow onto it.
  6. 6. From the dried tubes we form a cabinet for a coffee table - just glue them together (as tightly as possible) with PVA glue.

The created cabinet is usually fixed with strong threads and left to dry. Then we cut our homemade table from the top and bottom. We get a neat bedside table. We glue ordinary or mirror glass on top of it, using silicone, which is used to repair aquariums. Advice. Glass should be 1.2–1.5 cm thick. Thin countertops will be unreliable in operation. One careless move and they will crack.

In cases where the old window structure in the dwelling is changed to a new one (for example, to a plastic one), the dismantled product can also be adapted for a coffee table. We are waiting for a minimum of difficulties. We remove hinges, handles, other accessories from the window, wash the canvas well. If necessary, peel off the old layer of paint, polish the surface and paint with a fresh composition. Before us is a finished tabletop. You can install it on any legs. A great option is to make them from volumes that have been collecting dust on bookshelves in your home for decades.

We fasten the books to each other, forming legs of the required height from them.

The procedure is performed using superglue. Another option is to drill neat holes in the books and thread a steel bar through them. We install the updated window frame on homemade legs and rejoice at our ingenuity. Such coffee tables are good for interiors in retro, vintage, Provence styles. Instead of a window, by the way, it is allowed to use old doors, a mirror or just a large board, which had no place in the household.

Furniture for tea parties from pallets and boxes - simple and original

Wooden pallets are products used for the transportation and storage of various goods and cargo. Pallets perform the same function. But they are considered more modern designs. Both the first and second are ready-made countertops. Low tables from them turn out well. At the same time, the entire process of making home-made furniture from such products requires a minimum of time and labor from the home master.

We just need to thoroughly clean and wash the pallet, process it with a grinder and sandpaper, and paint it in the chosen color. It is not necessary to apply a single color paint. Color the table to your liking. Apply any ornaments and symbols to the pallet. And if you wish, you can not paint the workpiece at all, leaving the wood in its natural form. Small chips, scratches, cracks emphasize the natural texture of the structure.

We install the prepared tabletop on low wooden blocks or on wheels. Here you need to understand that the mass of pallets is quite serious - up to 15–25 kg. Therefore, wheels and legs for a table from a pallet should be selected wisely. They must withstand a given load. However, a pallet of sufficient height may not be equipped with legs. The design and without them will turn out convenient and reliable.

If there are no pallets at hand, it is really possible to make a table from any empty wooden boxes. Suitable containers for wine, vegetables, fruits. From two drawers you can build a small coffee table, and from four - a spacious structure for gatherings with friends. We assemble the boxes into square or rectangular furniture. We fasten them together with nails, putty the installation sites of the hardware with a mixture of glue and sawdust. We decorate the structure, cover it with varnish. We get a chic table.

In the free space between the boxes we put a vase or a pot of flowers. You can also cover it with a suitable sheet product. Nuance. Design experts advise making a plastic countertop coating if the interior of the home is made in the style of minimalism and modernity. For high-tech and art deco decors, it is better to use a sheet of polished steel. Country-style interiors are perfectly complemented by wooden flooring. And the glass, placed on a table of drawers, will harmoniously fit into any decor of the room.

Other ideas for assembling structures - a little more creativity

It is really possible to build a massive coffee table from an old cast-iron radiator. It is enough to tint it a little, install it on strong wheels, and cover it with glass on top (if possible, with rounded edges). The functionality of such a design, of course, is in question. She, nevertheless, weighs 60–80 kilograms. But here she does not hold originality. Not a single guest of your home will be able to ignore such an unusual piece of furniture.

And car lovers have the opportunity to make a convenient table from an old tire from their iron horse. Very often, tires are used to decorate the garden and vegetable garden. But even in the house, with proper preparation, they will look out of place. To create a table from a tire in the now popular eco-style, you need to stock up:

Table from an old tire

  • two circles cut out of a plywood sheet (we take their cross section a little less than the diameter of the tire used);
  • superglue;
  • cord, plait or decorative rope;
  • varnish;
  • self-tapping screws, electric drill;
  • wheels.

We attach plywood circles to the tire on both sides. Products can be put on superglue or (more reliable) on self-tapping screws. If you want the homemade plywood cover to open, one of the circles should be installed on small loops. Then in the niche of the tire it will be possible to store a variety of household trifles.

After that, we proceed to decorate the coffee table. We make a small circle from a rope (harness). We coat the middle of the plywood countertop with glue. Carefully fasten the rope element to it. Similarly, going from the center to the edges, we decorate the rest of the surface. Then we turn the tire over and continue to braid it on the sides. The bottom of the structure can not be decorated. Attach the legs to the bottom sheet (as an option - wheels). The table is ready. It remains to cover it with varnish or a special wax composition.

Fantasize more! Original tables for tea parties can also be made from other improvised materials. The more creative the craft will look, the more positive emotions you will experience when looking at it. Decorate your home with unusual homemade furniture, creating unique interiors. Good luck.

The table is the second object after the stool, which a novice furniture maker should take up. The design of a simple table is no more complicated than that of a stool; an unpretentious comfortable table for a summer cottage or for a picnic can be built in half a day using a hacksaw, a hammer and a drill. But a table made using the same technology and slightly ennobled can also look great at home, on the left in the figure, instead of an expensively purchased one. However, the table also gives greater freedom of creative self-expression, it can be a significant and even key element of interior design, it is not for nothing that handicraft furniture makers are called carpenters, and not sofa makers, cabinetrs or bedside tables. Having mastered the carpentry craft, it will be possible to take up exclusive tables over time, the rest of the poses. there.

This article discusses how to make tables out of wood. Wood is an environmentally friendly, affordable and easily processed material with remarkable aesthetic qualities. In utilitarian products, she forgives rather gross mistakes for beginners, but fine woodwork requires high skill. Having learned how to make wooden things, then mastering glass, metal and plastic will be much easier.

Tool and workshop

To make a table with your own hands, you need a production room separate from the living rooms: woodwork, as you know, is dusty. In addition, such good means of toning and protecting wood as wood stains emit harmful fumes during staining; nitro-varnishes, too, although to a lesser extent. Therefore, home carpentry should be well ventilated, and preferably with forced ventilation. You can use the garage, but there will be a lot of sawdust, and they will not benefit the car. Better to work in the barn; if it doesn’t exist yet, then you can build it, but on the farm it will come in handy for a lot of things.

The usual carpentry tool, on the left in the figure, is enough for a start. But the work will go much faster, and the result will be better if modern achievements are brought to the rescue, right there:

  • Swivel miter box, pos. 1, allows you to make saw cuts exactly in size and in angle in 2 planes. It is advisable to take it with a complete bow saw, so everything together will be cheaper, and the work will be more accurate. The miter box is a universal device, it will always come in handy and it is better to buy it.
  • Also universal is a manual electric jigsaw with an inclined shoe, pos. 2, which allows you to cut at an angle to the vertical plane.
  • Disc grinder, pos. 3 and 4, it makes it possible for a beginner to get the surface of a wooden plate in 5-15 minutes, on which an experienced carpenter with a skin in his hand will take at least an hour, and tape, pos. 5, also quickly and efficiently process the ends; there are also belt grinders for grooves and recesses with a protruding working body. These are already specialized tools, unsuitable for other work, and quite expensive, so it’s better to rent them first. True, craftsmen still successfully brush with grinders; artificially aging, a tree, but this is a delicate work.
  • It is also preferable at first to rent a manual wood router, pos. 6, with a set of cutters. They process shaped edges, choose holes and grooves.

A universal household woodworking machine (UBDS) of various modifications is very useful on the farm. It is compact, fits on a table, powered by 220 V 50/60 Hz 380-500 W. UBDS combines a circular saw, planer, wood lathe and a set of cutters. True, you can’t just grind the table legs on it, the tailstock caliper overhang is too small. But the caliper itself is just a steel round pipe, it is not difficult to lengthen it. The stop of the cutter remains regular, it is mobile, the leg and with a long caliper are sharpened in one setting.

How to choose a tree?

A wooden table can be made from any wood of medium resistance to decay, except for the softest species: poplar, aspen, alder, willow, ailanthus. Of the domestic ones, these include:

The rocks are listed in order of availability. For example, horse chestnut, sycamore and juniper are not harvested at all: the former are too valuable for landscaping in the southern regions, while juniper is endangered and protected. Industrial blanks of elm are almost completely used for shoe lasts, weaving shuttles, etc., and mountain ash - for weapons stocks; There is no full-fledged plastic replacement for them yet. Stone birch grows very slowly, in limited places, does not renew well, so its harvesting is strictly regulated, and the wood is expensive.

Note: walnut is especially valuable for furniture - its wood combines high hardness with excellent viscosity, the most openwork walnut carving does not prick. And walnut wood from burls - large growths on the trunk - is not inferior in texture to Karelian birch.

At the beginning of a carpentry career, it is better to limit yourself to pine, birch, oak, acacia and boxwood. Pine or oak will go to the countertop; birch - on the legs of a pine table; in the countertop, it is strongly warped from the spilled. Acacia and boxwood make excellent dowels, see below.

On a pine countertop made of boards, you can and even need to take low-grade cheap boards - knotty, serpentine. But, of course, without falling knots, cracks, wormholes and traces of rot in the form of spots of unnatural color: black, gray, blue, green, in general, not similar to this tree. For example, rot marks on black (ebony) wood may be whitish or yellowish.

Why is the countertop substandard? Perhaps also unedged, which needs to be finished on a circular and jointer? And after skillful processing of them, plates of remarkable beauty are obtained, on the left in fig. Manufacturers do not like such a tree: the production cycle is delayed, waste increases. But for yourself with your own hands, this is not so scary compared to the result.

wooden humpback

Commercial pine has a clearly defined zoning of wood in the form of annual growth rings; other conifers and many hardwoods also have it. On the saw cut of the board, the rings form the so-called. humpback in the form of thin concentric arcs. If the top of the tree is directed across the face of the board, as in fig. in the center, then when rallying the shield for the tabletop (see below), the boards are oriented with humps alternately up and down, from below in fig. If the ridges are directed towards the end of the board (on the right in the figure), then the boards are placed in the shield with ridges in one direction. These subtleties are necessary so that during operation the countertop does not split or warp.

Varnishes, paints, impregnation, glue

A free means of protecting wood from decay is used motor oil, but for what they eat from, this is not the best option. Optimal will be 2-fold, with a break of 3-5 days, impregnation with a water-polymer emulsion (WPE), it will give protection to the table for the entire time of its life. Even birch plywood impregnated with WPE is suitable for furniture front panels: it is also varnished on top and does not delaminate.

Old furniture nitrocellulose varnishes NTs-218 and NTs-2144 with solvent No. 647 are gradually falling into disuse: they are superior to water-based acrylic varnishes in all respects; in addition, they are safe to use. Also, glues, bone carpentry and BF-2 on alcohol are inferior to PVA; however, to obtain a high-quality seam, the latter requires applying glue to both surfaces, keeping them tack-free before joining, and holding them under pressure for 1-3 days, but this is acceptable for home production.

Wood for furniture can be pre-tinted and protected with a stain, which allows you to make beautiful typesetting parts; an example will be given below. To tint the assembled units, you can use paints based on the same lacquer and artistic (not paint!) dyes: oil in tubes for NC lacquers and acrylic water-based for the same lacquer.

First, they prepare a “painting”: they take 30-50 ml of varnish and squeeze 1-1.5 cm of paint into it with continuous thorough stirring with a paintbrush. The coloring is stored in a tightly closed vial and added to the varnish to the desired tone; a test for it is done on a piece of wood, the tone is determined by the complete drying of the varnish. Colored varnishes on NC and oil paints can be mixed according to the rules for mixing oil paints for painting; acrylic - no restrictions.

The first steps

The country table is the first of the homemade ones. If 1-2 brick pallets remain from the construction site, then the pallet table will be the first of the first. Not only because it is extremely simple, but also because it is very useful on the farm.

From one pallet, sanded, impregnated and varnished, you get a garden table like a coffee table, on the left in fig. If there is a pair available, in just half an hour you can make a wall-mounted desktop-rack, in the center and on the right. Chains for it can also be woven yourself from soft wire, covered with a PVC tube or, better, heat-shrinkable. To fully raise the tabletop, a small tool is placed on a shelf of a wall pallet.

With a little more work, a collapsible cutting table for a summer residence is made from one pallet, which allows you to transfer the summer-autumn harvesting campaign to the street without littering with husks and without trampling on the stumps. For the winter this table is collected in a compact package. The construction is clear from Fig; a bucket is placed under the hatch in the tabletop.

The next in order of complexity is the well-known country table-goats, colloquially a goat. Its construction of 40 mm boards is shown on the left in the figure, and in addition to it is a bench of the same device. And on the right - a country folding table on the same principle. It has swivel joints (M8-M12 bolts, washers and nuts with locknuts); in the place marked in green, a stop boss is placed on the nails between the crossbars of the tabletop. When folded, this table fits in the trunk of a car, so it will also go to a picnic. If this is not expected, or the trunk is larger, the countertop can be made longer.

Finally, it also does not require special tools and skills for a gazebo table, see fig. below. Material - the same magpie board and some inexpensive fasteners.

One step closer to art...

To advance in table building, now you need to learn some of the basics of carpentry. The table, in general, consists of a tabletop, its support frame, possibly with niches and / or mechanisms, or simply a plate - underframe - legs, and knots holding everything together. Let's go through them starting with the connections along with the legs, because. their fastening is the weakest point of the table.

Connections and legs

At first, we need to master the connection on dowels - round wooden bosses, see fig. Dowel joints are assembled on a quick-drying glue that does not require exposure: carpentry, BF-2, acrylic. Sometimes, instead of dowels, nails with bitten off hats are used to connect thin boards, pos. 4, but this is bad: the wood dries out, but the metal does not, and over time the connection becomes loose.

For dowels, a thin-layered tree is taken stronger than both connected parts, i.e. the hardest rocks. A pine table with birch legs can be joined on oak or beech dowels. On sale there are ready-made round sticks for cutting dowels; before use, chamfers are removed from the edges of the dowels. Plastic dowels are also sold, but they are intended exclusively for detachable connections, for example. inserts in sliding tables.

Legs for industrial tables are attached with detachable drawers, see fig. on right. Pos., marked in yellow - the simplest, cheapest and worst. With its shortcomings in the complete absence of advantages, buyers of Shiroptrebov's Soviet furniture are well aware, even if it remains there. Reliable, well-kept, except for the legs, and underframe boards, drawers with mortise jibs, “green” pos. They also require the least cost, but are quite laborious, so they are rarely used in industry, but just right for an amateur. Drawer side with shaped steel jib, top right in the figure, even stronger; in this way it is possible to fasten legs with a round head and in general any, however, purchased shaped parts made of high-quality steel are required.

Note: legs are attached to the round table, as shown below in fig.

Detachable legs are needed not only for ease of storage and transportation. In a small apartment with a narrow corridor, a table with legs is often simply impossible to push to the living room, no matter how you turn it. Modern apartments are more spacious, and in 1-story private houses the table can be served / given out the window, so in such cases, the strength and durability of the table with tightly fixed legs comes to the fore.

For tables on a rectangular base, the heads of the legs for blind fastening must also be rectangular, pos. 1 in fig. By the way, the tsargs are also one-piece: then the legs with dowels that pass through a mortise wooden jib. From the inside, the dowels are cut flush and wedged with dogwood or boxwood wedges inserted across the fibers of the jib wood. Assembled with glue, such a connection is so strong and durable that these 200-year-old tables can be fought by grabbing the leg.

Sufficiently high-quality tables on turned legs are assembled simply on dowels, pos. 2. For simpler tables, the legs are made of timber and fastened with self-tapping screws after attaching the tabletop to the tabletop, pos. 3. Even simpler and lighter are the legs of a pair of boards each, pos. 4 and 5. So that they do not cling to the floor, you need to stuff the thrust bearings on them below or put the table on wheels.

table top

The easiest, but not the cheapest way, is to order a countertop made of laminated chipboard (chipboard, laminate). Chipboard for countertops is available in the form of the so-called. postforming - slabs 3.6x1.2 m 20-60 mm thick with a decorative coating. The upper edge of the postforming plate is rounded, the bottom face with a drip collector, see fig. Modern furniture laminate is quite environmentally friendly, no matter what gossip does not want to forget the co-furniture, which stank of phenol for months.

Postforming is well bought by small furniture enterprises. They always have his scraps; of them, they will gladly and for a very affordable price cut the tabletop to size, if the company has a jig saw. Perhaps such an order will be accepted by a single individual entrepreneur if he is sitting idle. The finished slab will be closed, i.e. cover the PVC end with a piping (edge). If you will be edging yourself (sometimes they ask for an awkward surcharge for edging), then keep in mind:

  • The upper and lower flanges of the edging have a different profile, see on the left in fig. Confuse - there will always be a piping of dirt on the table.
  • Kant must be taken exactly according to the thickness of the plate. It is possible to put on a 24 mm edging on a 25 mm plate, but it will soon slide off.
  • The groove for the crest of the edge must be selected with a manual disk cutter; saw, it seems that no one has yet succeeded as it should.
  • Before installing the edge, a thin layer of silicone sealant is applied to the end surface and the "sausage" is squeezed into the groove; in this case, the silicone will also be a lubricant, without which the ridge of the edge can simply be crushed.
  • The comb is inserted into the groove with light blows of the mallet, gradually moving along the contour. The tabletop must lie face up on the support; squeezed out excess silicone is immediately washed with a clean rag slightly moistened with table vinegar.

Plank tabletops are rallied in plank clips with wedges and spacers - wimahs. Wimes are quite possible to make yourself; You need 3-4 for a table top. Wym boards (cheeks) are wrapped in polyethylene so that the shield does not stick to them. On fig. for example - the process of manufacturing a round tabletop; rectangular rally in the same way, only cropping to size is easier. The shield is rallied onto the countertop with glue and dowels (see below); if the boards are grooved, dowels are not needed. When rallying to PVA, the next plot is kept until the applied glue is tacky before installation in the wyma.

Often, countertops are assembled without a wym on a plaza - a flat surface covered with plastic wrap. It will not work to assemble a good plank shield on the plaza: either it will come out slitted, or the boards will stand on end when assembled. But inlaid countertops from fragments are simply wonderful in skillful hands. For example, at pos. 1-3 fig. - a tabletop made of sawing waste, tinted with wood stain. And on pos. 4-5, the base of the tabletop was the plaz itself made of thick plywood. The tile and its break are glued with tile adhesive, then the depressions are filled with grout for drinking, the surface is lacquered and the contour is edged with a wooden lath.

Note: these examples do not illustrate all the possibilities of making do-it-yourself inlaid art tabletops.

Underframe

The underframe of the table with non-removable legs is a simple wooden frame, on the left in fig. Niches and details of mechanisms are not involved in the power circuit. If the table is longer than 1.2 m, or the tabletop is removable/sliding, or heavy operational loads are expected (for example, a work table), the underframe is reinforced with stiffeners in the center. If the legs are fastened with drawers, then the underframe is made integral with the table top, so that a single power circuit is obtained, on the right in fig.

no frame

Tables without underframes are also known, in which the tabletop with legs work in a single carrier system. Very durable, eg. plywood table on the left in pic; its connections are shkantovye. Unfortunately, this is not an economical design for an amateur: the sidewalls cannot be assembled from pieces, they must be solid. In mass production, the waste is not very large, but a sheet of plywood with a thickness of 24 mm or more will go one piece for large sidewalls, and 1 more for smaller ones. The table on the right is already quite possible to make with your own hands: the supporting frame is prefabricated; connections - in a spike with a tightening bolt and half a tree. However, the countertop in this case should be round or square, with rounded or right angles.

... and get into the kitchen

Exactly. The table for the kitchen is the next in order of complexity after the simplest country ones. It must already meet the requirements of apartment ergonomics, dimensions - 75 cm in height for people of average completeness; the width of the seat for 1 eater / rider is 60-80 cm, depending on its corpulence, the width of the tabletop is at least 70 cm. The countertop should be easy to clean, durable, resistant to spilled heat from hot dishes.

All these requirements will be satisfied by a table made of chipboard on metal legs; they are also sold separately in sets of 4 pieces, with fasteners, on the left in fig. Factory legs for tables, as a rule, are supplied with height-adjustable heels. The table, the manufacture of which will be reduced to screwing the nests of the legs with confirmatory screws, will cost 30-50% cheaper than the whole purchased one, but in appearance it will not yield, on the right in Fig.

If you are not too lazy to put your hands on it, steel legs can be made with your own hands. This is not only a cheaper, but also a more durable option: the sockets of branded legs are cast from a rather fragile silumin, the fasteners weaken over time, they need to be tightened. You yourself can cut out nests from good steel, and weld your own legs into them.

The kitchen is more spacious, perhaps there is room for a larger table. In such a case - on the trail. rice. drawings of a kitchen table in a rustic style. "Rustic" this table is not only in appearance: it does not have a single nail and metal fasteners in general. Just wood and glue. A connoisseur, seeing such, nods his head in understanding and approval, and the design is simple and accessible to a beginner. True, in addition to the tabletop, you will have to rally the shields on the sidewalls, but in this case, the extra work is worth it.

Kruglyashi

A table with a round top is appropriate in any room, if it fits there. But a tabletop made of boards in this case is not the best option: due to the presence of sharp corners, it is subject to splitting without a frame, which is very complex and time-consuming. Type-setting countertops from small fragments, like the one described above from waste, are free from this drawback; unlike laminate rounds, they are decorative, stylish, unique, and practically free.

There are even more sharp corners in a small-type table top, but here the “broom law” works. Not the American senator Venik, who loves democracy in Russia to the point of complete oblivion of it at home, but the broom with which they sweep the rubbish. As you know, it is impossible to break him (a broom, not a senator) tied up, and a child will break twig after twig. So here, due to the ease of distributing loads between small fragments, the table top made of them works like a solid plate, and you can cut it off after assembly even with the letter zyu.

Note: the idea of ​​the broom senator, sorry, Venik, was suggested by the statement of his compatriot Samuel Clemens, world-famous as Mark Twain: “I affirm, and undertake to prove it, that Mr. Cooper has no more fantasies than a bull. But not the bull that lows in the pasture, but the one that is the support of the bridge.

How to make a semi-folding round table is shown in fig; on the right there are the dimensions of the countertop and the assembly order. And in fig. on the right above - a small round table for the hallway, according to the old classification - a business card. Its feature is the minimum number of connections; glue assembly. Any kruglyash will go to the countertop, from a stump saw cut to a cardboard one, made according to the method of manufacturing cardboard shelves, but the underframe must be durable, made of wood (dvuhsotka board) or chipboard.

Moving on to the living room

The table in the main room of the house should be in line with the whole house. At the same time, with the modern desire for laconic design (which also saves living space costs), the table should not catch the eye for the time being, and take up less space. Therefore, one of the most sought-after pieces of furniture of our days has become a transforming table.

The simplest transformable table, which, with all its transformations, remains a table, and does not turn into a closet or bed - a bedside table; it is quite possible to make it with your own hands "from scratch". There are 2 most common options here. On the left in fig. - the table is deployable, it has a record ratio of occupied areas in expanded and collapsed form. These are most often placed in studio apartments perpendicular to the wall on the border of the kitchen and living areas. With the tabletop wings lowered, it will serve as a bar. By raising the wings one by one, you can get a kitchen or everyday dining table, and fully extended (in the center), it will provide a place for a rather crowded banquet.

A bachelor living in a small apartment is more suitable for a folding bedside table, on the right in fig. These are, in essence, 2 small round folding tables, described above, connected by a rectangular insert. You can have lunch alone from it folded, because, unlike the previous version, there is where to put your legs. And having unrolled, spend a romantic evening with a beautiful stranger or sincere gatherings with friends.

All of the above qualities combine coffee-dining tables-transformers with a mechanism. The variety of transformation mechanisms is great, but for tables that are always tables, they basically come down to 2 types: an elevator (pantograph) and a book. How one and the other work, see the video:

Theoretically, a book is more stable than an elevator, although much depends on the quality of execution. It is more popular among book lovers, because the mechanism-book can still be made independently, and the elevator outside the production environment is unlikely.

How the table-book is laid out is shown in stages in fig. on right. For its independent production, you need to know that the key unit is the damping-balancing elastic link. In fairly expensive branded designs, very soft gas dampers (gas lifts) are used, but it is better for an amateur to stop at a spring damper, and not because a gas lift is much more expensive.

The fact is that the gas lift must be coordinated within fairly narrow limits with the kinematics of the lever system, the weight of the table top, underframe and the own weight of the levers. If the balance of the entire system does not fit into its characteristics, the mechanism simply will not work. And the spring can always be tightened / loosened; replace as a last resort. In general, an unsuccessful home-made transforming table with gas lifts rarely manages to be “brought to mind”, and spring almost always. If you still decide to suffer with a homemade acrobat table, in fig. - drawings of the spring transformation mechanism.

Without the availability of or access to drilling, turning and milling machines for metal, most parts of the transformation mechanism will have to be ordered. Then its production will cost a little about $40, and you can buy a good ready-made one for $50-$60. A factory-made transforming coffee table rarely costs less than $200, so even in this situation, the savings are significant.

The transformer table is made under the mechanism. One of the most popular are the Mazetti transformation mechanisms, due to their good quality at a moderate price for this class of products. In addition, Mazetti movements are available in a supporting frame (inset in the center in the figure), which greatly simplifies installation. The rest of the pos. in fig. show the device and dimensions of the table for this mechanism.

For a strong feast

Whatever you say, but in a normal family with children, friends and relatives, crowded gatherings at the table cannot do without, and here the transforming table will not always help out. However, we will leave more or less full banquet tables for the living room, as they say, for later: these are products of a higher order of complexity; primarily because of the extension mechanism.

By the way, the good old “sliders” with wooden guides and wooden sliders of the halves of the table top (item 1 in the figure) are quite convenient and reliable if properly executed, in addition to this, they can be made by yourself, but such a process requires a special detailed description. Modern sliding mechanisms with telescopic full extension guides, pos. 2, allow you to use not 1, but up to 3-5 inserts, which increases the capacity of the table by 6-10 people, respectively, but they are quite expensive, and their installation requires a description of no less voluminous.

There are banquet tables with clamshell inserts, pos. 3. In elite models, when sliding / sliding the halves of the tabletop, the insert raises, unfolds and puts in place or puts back in the underframe a very complex mechanism, but its manual versions are available for home production.

As for banquet tables with retractable individual tables, arranged like a keyboard stand in a computer desk, they cannot be called popular by any means: leaning forward (and how to avoid this if the house is without servants?), We get the board back into the underframe, and our portion of treats - for festive clothes.

But let's not talk about sad things. Recall that the table is not always pushed apart, and you can use the side table, but the whole table is in any case more reliable. Therefore, in the series of drawings below - a way to make a very durable and inexpensive dining table, and how it looks "alive" - ​​see the left in fig. at the beginning.

In addition

A table, and indeed any furniture, often wants to be painted not just with stripes or artistically painted. To protect the drawing from external influences and to ensure the possibility of updating the varnish if necessary, the paints should not be applied, but rubbed into the wood before varnishing. The technique of painting by layer-by-layer rubbing of paints is called glazing. So in conclusion, we offer a master class on wood glazing.

Video: wood glazing master class

Do you love designer clothes, but sigh in frustration when you look at the price tags that adorn them in stores? Try to become a designer yourself. Think it's difficult? Nothing like this! Following the instructions, you can easily create an original piece of furniture from improvised materials with your own hands. And we suggest starting with a coffee table - such a simple, but very important piece of furniture. Believe me, at such a table you will be happy to give tea to your guests, who will admire your skills. In addition, by creating a coffee table with your own hands, you literally fill your home with warmth and put a piece of your soul into it. So it's definitely worth a try.

Romantic idea. All year round, drinking your favorite drink at this table, you will remember the warm sea, the gentle surf and the moonlit path. "Marine" table is tenderness, sophistication and originality in the heart of your home.

How to do?

1. Take an old window frame and clean it of dust and dirt. If the old glass is cracked, insert a new one, then get rid of the layer of old paint and sand the surface. Next, you should remove the metal corners, which additionally fix the frame parts.

2. Cover the frame with white enamel or acrylic paint. If you chose acrylic paint, after drying, sand it with sandpaper so that the wood shows through - this will make the table look aged, which will give it a special sophisticated look. You can also use two colors by choosing a white and blue gamut. First, paint the frame with blue paint, and after the first layer has dried, cover it with white. When the second layer dries, rub it with sandpaper - then blue will come out from under the white paint.

3. We make legs for the table. To do this, take the cutting and cut it into 4 equal parts (each about 34 cm), then go over them with sandpaper to remove all the roughness.

5. Now each blank needs to be drilled in 4 places. Pre-mark and then drill a hole for attaching the legs, as well as another one - in any convenient place - in order to secure the legs more securely.

6. After that, using a long self-tapping screw, you need to attach each leg to the base.

7. Next, you need to attach the legs to the frame using self-tapping screws. The window frame is a kind of “box” in which it will be necessary to put all the sea gifts brought from the rest - the front part of the frame, which stands on legs, will be facing the floor, down.

8. Now you will need a coarse thin rope, which will need to be braided around each leg. Fix the rope using a glue gun.

9. Now you need to wash and degrease the glass on both sides. Next - pick up and place on the glass "seafood". Arrange them so that it seems as if they are casually scattered and at the same time flow from one corner of the table to another - and their number should gradually disappear. Now you need to attach each element with a two-component transparent adhesive. At the same time, marine elements should not protrude above the edges of the flat “box”.

10. You will need to order glass from the glass workshop, the thickness of which will be 4 mm. The size of the glass should be such that, leaning on the frame, it can cover the “box”. At the same time, 1.5 -2 cm of the frame should be open on each side. In the workshop, you need to ask that the edges of the glass be processed and holes 4 mm in diameter should be drilled into them. The glass needs to be wiped and covered with a table. From leather or thin rubber, cut out spacers that will be under the washers. Fix the glass with self-tapping screws. Screw them in carefully so that the glass does not crack.

11. Take a coarse thick rope and make a loop at one end, which will be equal to half the length of the table. Using a hot glue gun, glue the folded rope in half from the center of the long side of the table to its edge. The loop itself (about 12-15 cm) does not need to be glued - it should be free so that you can then tie a knot. “Bypassing” the glass around the perimeter and going around all its corners, continue to glue the long end of the rope to it. When you reach the loop, you need to thread the end of the rope into it so that you have a sea knot. Now, stretching the rope in the opposite direction (doubling), you need to glue it.

12. Decorate the outer corner of the table - on the side where the most marine elements are located. Make a continuation of the composition by placing additional details as if they are “draining” from the table leg right under the glass of the tabletop.

Ready! Enjoy your creation and give joy to your guests!

Table-suitcase for travel lovers

A very original solution for an old favorite suitcase that has seen other lands with you and that you don’t want to throw away because of the memories.

How to do?

To get started, go to the store where you will need to purchase furniture legs (wooden or metal). If you want to make a mobile table - then you need to take the wheels. You will also need plywood, screws and a screwdriver.

Now we make markings on the bottom of the suitcase for future legs and drill holes. Since it will not work to attach the legs to the fabric, we put plywood inside the suitcase, make markings on it through the holes and also drill it. Now we attach the mount to the bottom of the suitcase and fasten the legs. Using hot glue, glue the felt inside the suitcase.

To give the table an original appearance, reminiscent of distant travels, you can decorate it with stickers made in the form of stamps, or decorate it at your discretion.

That's all - an unusual coffee table is ready! By the way, there are a lot of options for turning suitcases into tables: choosing the legs to your liking, you can make a table in retro or classic style. You can not attach the legs at all if you have a massive suitcase - it will look truly incredible: such a table will bring a sense of adventure and adventure into the interior, the spirit of travel and unexplored distant countries.

Log table for nature lovers

A table made of logs for connoisseurs of the nature of a summer house or a country house is warm and natural, it will always evoke the mood of a weekend, in which everything is saturated with tranquility, birdsong and the scents of nature. Making such a wonderful table is also quite simple.

We take wooden bars (in this case, birch) of the same height and width, only 32 pieces. You also need to take the base for the table, legs (4 pieces), putty to match the wood, a screwdriver and glue designed for wooden surfaces.

First you need to assemble the base for the table, then glue wooden bars around the perimeter, and sew up the middle with cardboard. Then we fasten the legs to the bottom. Next, we glue thin wooden dies to the inner surface - thanks to this, it will seem that the table is completely wooden. Now we take the putty and carefully close up all the voids, after which we overwrite until an absolutely flat surface is created. Voila! Now you are the owner of an unusual table that will become the highlight of your interior.

If you like the idea, you can create other tables according to this scheme, using, for example, branches instead of bars. To create such a table, you need to take a plywood box painted with black paint, the size of which is 40x40x60 cm (or any other size of your choice).

To glue the frame, we take branches, from which we first remove the loosely holding bark (we do this with sandpaper). What is the procedure for gluing: first we glue the branches on the long side of the table, and then we select wooden dies and, like a mosaic, lay them out on the ends. The thickness of the dies should be approximately 1 cm, they can be cut with a parquet or circular saw. And finally - install the glass, which will be the countertop. If desired, by screwing wheel supports to the table, it can be made mobile.

Using the same technology, you can create many more unusual pieces of furniture. You can lay out the branches horizontally and then you get such a wonderful table. Such furniture looks not only very original, but also incredibly stylish.

original pallet table

An original table made of pallets of pallets, which are probably lying around in every country house? And you can make them a very convenient and functional element of the interior.

How to do?

To get started, collect all the tools you need for your idea: the pallet itself, a drill, clamps, a hammer, screws, a nail puller, glue designed for wood, wheels, soap, a primer, a screwdriver. In addition, take paint brushes, a petal brush head with abrasive bristles for a drill, varnish and a colorless primer.

First of all, you should take a drill with a nozzle designed for processing wood and clean the surface of the boards from dirt with it. Now carefully disassemble the sanded pallet into parts. Lightly tap the rusty nails with a large hammer and carefully pull them out with a nail puller. Glue the broken pieces of boards with wood glue. At this stage you will need clamps. They need to carefully clamp the boards and wait until they dry out.

Now the parts prepared for the countertop need to be nailed and glued on the reverse side, then clamped with clamps and wait until they dry.

Then cover the table with a colorless primer, and then varnish. Next, on the back of the table, mark the places for the screws to attach the wheels. Drill holes for the fasteners. In order for the screws to easily enter the wood, grease them with soap. Using a ratchet, you can quickly and conveniently tighten hex screws.

Stylish, compact and quite functional table is ready!

Photo instructions for making a coffee table from pallets

Table from boxes

A table made from drawers of drawers? But it has come, and now you yourself can create such an unusual piece of furniture at home. Surely you yourself will be delighted, and your guests will appreciate the originality of this idea.

How to do?

Take 4 wooden boxes, sandpaper, water-based varnish, roller and brush, dowels, 10 mm plywood sheet, PVA glue, 4 wheels and self-tapping screws.

First you need to sand the boxes and varnish them. Then, using a drill with an emphasis, make holes at the ends of the boxes. Using wood glue, you need to fix the dowels in the attachment points and connect the ends of the boxes to each other. Attach the wheels to the plywood sheet, and then attach the sheet to the boxes with self-tapping screws. The table is ready!

These extraordinary things can be created from quite ordinary materials. Having imagination and a desire for originality and comfort in your home, you can easily work wonders. Look around: maybe the old window frame has every chance to turn into an interesting element of the interior?

Or maybe a huge wooden reel from an industrial cable that can become an elegant piece of furniture?

Believe me, there are a lot of things around us that can turn into something truly unique and precious. You just need to look at them from a slightly different angle.

Fitting © 2022 Design and interior of apartments