How to remove limescale in the toilet? An effective toilet cleaner. How to properly clean the toilet: step by step instructions How and how to clean the toilet from the stone

The condition of the toilet over time will depend on the care of its use. This plumbing fixture needs to follow the recommendations for its operation, so as not to worry later on how and with what to remove limescale in the toilet. Quite often, a urinary stone also settles on the inner walls of the bowl.

Causes of deposits

Deposits can build up on the rim of the toilet bowl and in the drain hole due to infrequent cleaning. Another reason for this is the irregular flushing that occurs in families with babies. Untimely descent of water contributes to the fact that urine on the walls of the toilet turns into a mineral plaque. Its density increases over time, resulting in the formation of a stone. It will not be possible to remove it with the help of a brush alone; household chemicals are also unlikely to help with this.

Excessively hard water with the appropriate chemical composition can lead to limescale. To prevent the formation of plaque from time to time, the toilet bowl must be cleaned with special products and care must be taken to soften the water. The cause of the growth of lime and urinary stone is damage to plumbing. These defects are due to improper operation. For example, if you pour hot liquid into the bowl of the device, then small cracks will appear on its walls, around which plaque will form.

Cleaning and type of coating

If you are faced with the question of how to remove limescale in the toilet, you should think about the type of plumbing coverage. In the production of such products, glaze with different coatings is used, which can be:

water repellent;
anti-mud;
antibacterial.

These materials have their drawbacks. When using hot liquid, the coating cracks, which spoils the appearance of the device and becomes a source of bacteria. Although the material is resistant to external influences, it can suffer from acids.

When you are faced with the question of how to remove limescale in the toilet, you should not use abrasive powders and hard washcloths, because this is unlikely to help. In advanced cases, when the pollution is impressive, it is necessary to think about the use of expensive means. A rational option is sometimes the acquisition of new plumbing.

Use of household chemicals

If you want to clean plumbing that is overgrown with deposits, you should remove the water from the bowl. To do this, you can use a glass with a handle or a plunger. After you need to use detergents that are applied to the walls and left for about an hour. If necessary, the composition is poured again, and then removed with a brush along with the plaque. If there are old deposits on the surface, more serious compositions should be used.

Lime scale removers like Pemolux abrasive powders provide easy application. Water is scooped out of the plumbing, and the powder is distributed over the surface. It will be necessary to act mechanically on the bowl until the surface becomes perfect. The job is pretty tedious. Another disadvantage of the method is the loss of smoothness of the walls of the toilet. As a result, the coating is overgrown with microcracks, where dirt begins to accumulate.

Cleaning the toilet from a urinary stone can be done with alkaline products. This should include Domestos and "Whiteness". The composition contains a solution of caustic soda, which removes the stone. It will be possible to deal with its remnants with a brush and water. The water is pre-drained, the solution is applied to the dirt, and washed off after half an hour. The procedure can be repeated twice if necessary.

Alkali effectively corrodes urinary stone and limescale. In the process of carrying out the work, the tank is blocked, which is especially true when it flows. According to the principle of alkaline compositions, acid-based products act. One of them is Silit.

The use of folk remedies

If you are thinking about how to clean the toilet from limescale, you can use folk remedies. Ordinary vinegar will help in the fight against stone. A glass of liquid should be heated to 40 ° C and add some baking soda and medical iodine to the container.

The mixture is poured into the toilet and left overnight, thanks to which the stone is completely dissolved. When housewives think about the question of how to clean the toilet from limescale, they often resort to the decision to use citric acid. With this tool, you can remove the stone and plaque. Two packs of powder will suffice. The product is poured into the bowl, and the lid is closed. After 3 hours, the stone will dissolve. You will only have to remove it, repeating the procedure if necessary.

Oxalic acid is an alternative solution. Its technical variety is sold in powder form. Before using it, you should read the instructions in order to comply with safety measures. Rubber gloves should be used. The powder is applied to a damp cloth, which should be wiped with areas covered with plaque and urinary stone. If desired, you can dissolve the acid in the bowl of the plumbing fixture and leave it for an hour. Powder in this case will need a little more.

After the cleaning is completed, the plumbing is washed. If you are still undecided about how to remove limescale in the toilet, you can use electrolyte. This method is most effective in the case of old pollution. When performing the procedure, you must use a respirator, goggles and rubber gloves. The electrolyte is poured very carefully, it is important not to splash it. This tool will not work in the presence of plastic pipes.

Strong chemistry in the fight against deposits

Before proceeding with the procedure for cleaning the toilet with potent chemistry, you must read the instructions. There you can find out how much of the drug for a single use should be applied. It is also important to observe the time of action. A person needs to protect the respiratory and vision organs, as well as the skin of the hands from accidental contact with alkalis and acids.

Before dissolving the limescale in the toilet, you should consider whether the product is suitable for household conditions where the piping is made of plastic. Such compositions should not be used for local treatment plants like septic tanks. This applies to liquid alkalis and acids. An example is phosphoric acid in the form of a 7% solution. It can clean the toilet from stone, as well as free the internal components of the drain tank from corrosion.

For use, pour 100 g of the solution into the tank and the toilet. After 15 minutes, the water is washed off and the surface is cleaned with a brush. Acid has an affordable cost, and does not affect plastic, rubber and enamel. Before you clean the toilet, you must choose a product. One of them is hydrochloric acid solution. This composition is very strong, so it requires some caution. It is forbidden to inhale vapors, and hands must be protected.

The walls are wiped, and then the acid in the amount of one glass is poured into the bowl. In 15 minutes you can rid the plumbing fixture of contamination. After pouring the mixture, the lid is closed. This product is not suitable for toilets connected to plastic pipes.

Use of chlorine

Chlorine is an excellent toilet cleaner. On its basis, many compositions are produced, where “Whiteness” should be attributed. Chlorine-containing drugs are detrimental to health, so their use in recent times is not recommended. But if you still decide on this, then the composition must be applied to the surface, and after an hour, clean the toilet with a brush and rinse the bowl.

tank tablet

When choosing a toilet cleaner, you should pay attention to the tablets that are placed in the tank. They act as a plaque remover and are suitable for the prevention of urinary stones. These products have a pleasant smell, disinfect and disinfect the surface of plumbing, extending its life.

One tablet is placed in a bottle. As soon as it begins to dissolve, the water will turn into some shade. If the coloring pigment disappears, this will indicate the need to add a new tablet to the tank.

Use of soda

If you started cleaning the toilet from a urinary stone, then you can use quite unusual means. For example, Sprite or Coca-Cola. This popular recipe appeared recently. It consists in the need to pour one or two bottles of the drink into the toilet bowl. These liquids contain citric acid, which quickly corrodes deposits.

Finally

Plaque in the toilet can appear due to irregular cleaning. You can reduce its likelihood or completely avoid the formation of a stone with the help of simple tips and means. It is important to eliminate the leakage of water from the drain tank. In some cases, it is enough to adjust the float.

If desired, you can use tablets, thanks to which deposits will not form, and plaque on the walls will partially dissolve. We remove limescale and rust from the toilet every week with special tools. To do this, the gel is applied to the surface, and after 30 minutes it is washed off.

We spend quite a lot of our time in the bathroom, so it already happens :) Therefore, everything should be beautiful, clean and comfortable there. But here's the problem - on the walls of the toilet often formed outgrowths of urinary stone, which must be removed. Otherwise, cleanliness and comfort are out of the question. The Seasoned Plumber's Advice blog offers time-honored, time-tested methods on how to remove a urinary stone in a toilet bowl. Moreover, advice using what can be found in every home. So…

When does a urinary stone appear and how to remove it

Most often, deposits on the walls of the toilet are found in crowded apartments, where there is one bathroom for several people. An ugly and foul-smelling plaque on the walls of the toilet does not appear immediately, but growths are formed necessarily. Unless, of course, preventive measures are taken :)

Therefore, the removal of a urinary stone will take a minimum of time if you pour half a glass of Whiteness (household bleach solution for bleaching linen and disinfection) into it once a week for 1-2 hours. Don't forget to cover the toilet with a lid - the smell of bleach spreads quickly. Then it remains only to drain the water after an hour or two, carefully remove the deposits with a wooden stick and forget about this unpleasant procedure for a week or two.

But if you got a running plumbing fixture or the hostess was absent from the house for a long time and no one looked after the toilet, then more drastic measures are needed.

How to clean a toilet bowl from a urinary stone

Do not try to scrape with an iron mesh or a brush: the process is long, traces of metal remain on the sanitary ceramics, and it will not be possible to completely get rid of the growths.

You can dissolve a urinary stone that has grown over a long time in several simple ways:

The most effective one has already been described - pour bleach. To improve the effect, repeat the procedure until the urinary stone is completely removed. A small note: if the hostess is in an “interesting position”, then the bleach method cannot be used.
Fall asleep at night ½ pack of baking soda ash. It is washed off in the morning in several doses, but it works well. Provided that no one used the “night vase” during the entire procedure.
Pour a bottle of Coca-Cola or Sprite (1.5 l) into the toilet at night. The citric acid and carbon dioxide found in these drinks “eat up” unsightly growths on the walls of the toilet bowl. How it works - see the video at the end of the article.

Note: meet tips clean the toilet from urinary stone with very exotic methods- pour in heated vinegar (think about what will happen to the enamel after scalding) or electrolyte from under the battery (the plastic corrugation to the toilet will not withstand, and the sewer riser will be at risk of leakage), pour oxalic acid (destroys enamel) and other methods. Don't take risks. The toilet is an expensive device, and its replacement requires financial costs. Just try one of the above methods. Definitely work, check it out :)

And one more piece of advice: if you have a cup for a toilet brush that closes tightly, pour some bleach (“Whiteness”) into it. This will ensure the cleanliness of the cup itself, the brush, and will disinfect the toilet every time you use this brush.

I will be grateful if you press the buttons :)

Lime deposits form on the surface of any plumbing fixtures, with which you constantly have to fight. The toilet bowl, in addition to limescale, also pleases us with the appearance of urinary stone on the walls over time. And the hostess is faced with the question: how to clean the toilet from limescale and urinary stone? The task, it would seem, is not an easy one. But in our age of scientific progress, there are many ways to get rid of these malignant misfortunes. Let's take a closer look at the ways in which you can return our toilet bowl to its former whiteness.

Causes of urinary stone formation

We all know that limescale appears as a result of the deposition of minerals contained in our water. But not everyone knows what a urinary stone is and where this attack comes from. Such plaque is essentially the interaction of the same minerals from the water with minerals that are excreted in the urine. As a result of their interaction, a dense gray-yellow coating is formed, which housewives do not like so much.

Let's look at the reasons why it begins to grow rapidly and bring inexperienced housewives to nervous spasms:

Very often this can be seen in a house where there are small children who do not remember what needs to be drained behind them. That is, the main reason for the occurrence of urinary stone is untimely or insufficient draining. In this case, mineral deposits from the urine settle on the walls of the toilet and remain there.
Such a problem can occur if the drain tank is malfunctioning.
If you have a toilet bowl with a rough surface or an old toilet bowl at home, then the likelihood of a raid increases many times over.

Important! The urinary stone grows and increases over time, therefore, at the first signs of its appearance, you need to “take the bull by the horns”, or rather, begin to fight it immediately.

How to wash the toilet from urinary stone at home? How to do this - we will tell you now.

Dealing with urinary stone

How to clean the toilet from urinary stone at home? The easiest way to get rid of this scourge is to use household chemicals.

Special household chemicals

Find the right toilet cleaner. This can be done by examining the labels or by consulting with the seller.

Important! Don't forget that you will also need gloves and a respirator. But children and allergy sufferers need to be evacuated at this time.

Operating procedure:

For the best effect, you need to drain the water from the toilet. This can be done with a mug or in any other way convenient for you.
Now you need to put on uniforms - gloves and a respirator.

Important! You don't have to, of course, but most chemicals are very aggressive and can get you into a lot of trouble when working in a small space with bare hands.

The remedy of your choice should be applied to the places where the urinary stone appeared and left for several hours.

Important! During this time, you can not use the toilet.

When enough time has passed, rub the treated areas with a brush.

Important! Do not use metal brushes. They can scratch the surface of plumbing, as a result, plaque will form even faster.

If the layer of plaque was thick, then you are unlikely to be able to get rid of it on the first try, but several repeated procedures will do their job and help to cope with the problem.

In addition to various popular toilet cleaners, there are other ways to clean the toilet from lime deposits and urinary stone using chemistry.

How else can you remove a urinary stone in the toilet?

Bleach

You can buy a bag of bleach, pour it down the toilet and leave it overnight. This will destroy the stone and kill the bacteria. And yes, it will cost you less.

Anticalc

This tool will cope with any plaque. Pour it into the toilet and leave it overnight, and in the morning remove the remaining dirt with a brush.

Oxalic acid

Oxalic acid copes very well with similar problems. It is crystals. They can simply be poured dry on problem areas or diluted with water or alcohol.

Hydrochloric acid

A very good remedy is a 33% hydrochloric acid solution. But this requires great care - the product is toxic, it is necessary to protect hands, respiratory organs.

Wipe the walls, pour a glass of product into the toilet bowl, and you will quickly get rid of all kinds of dirt in 15 minutes. At this time, the toilet lid must be closed.

Important! Do not use this tool if the toilet is connected with plastic pipes.

Liquid battery electrolyte

This method can be used in rare cases - this powerful tool will perfectly clean your toilet from any plaque, because sulfuric acid is included in the composition.

Tank tablets

How to wash the toilet from stone and plaque? On sale there are special tablets for the tank, which are suitable both for the fight against urinary stone and limescale, and for prevention. It is enough just to put one tablet in the tank. The water will turn into any color.

Important! This tool disinfects and disinfects the surface of the toilet bowl, extending its service life. In addition, it usually has a pleasant aroma.

Cleaning folk methods

In the fight against urinary stone, all means are good, and especially folk methods, because they have been tested for more than one year. Remember to protect your hands and respiratory organs and protect your eyes from splashes when using any of the following:

In the fight against urinary stone, table vinegar will help you. It will soften any deposits on your plumbing. Before applying it to problem areas, pump out the water from the toilet and wipe the inside with a dry cloth. Leave for 2-6 hours and then brush with a brush, not a metal one. This cleaning can be repeated several times until the toilet is completely clean.
If just vinegar did not help, then mix it with baking soda - one tablespoon of soda goes to 200 grams of vinegar, or with iodine in a ratio of 1 to 1, and heat it up to 50 degrees.
How to remove a urinary stone in the toilet? One of the simplest and most affordable remedies is citric acid. A few sachets of this remedy per night can dissolve any plaque. Moreover, the procedure can be repeated several times until the problem is completely solved.
Help to cope with the problem and baking soda, generously sprinkled on places with deposits. They also fall asleep at night and leave it, and in the morning they clean it along with the remnants of plaque. For greater efficiency, any cleaning agent can be added to soda.
As a last resort, you can try the power of Sprite or Coca-Cola. They contain a lot of citric acid, which will dissolve plaque. You will need 2-3 liter bottles, which will have to be poured into the toilet.

Prevention measures

To avoid such serious problems, you need to take preventive measures and not bring your toilet to the point where you have to clean it with hydrochloric or sulfuric acid. Urinary stone appears gradually and grows on running plumbing. Therefore, we take preventive measures:

Periodically clean the toilet bowl with special means. Any product, especially chlorine-containing, will cope with small pollution.
Make sure your tank is not leaking. If it is faulty and flows all the time, this leads to the formation of plaque. Especially in areas with hard water.
An excellent prevention will be special plates that are attached to the walls of the toilet. They clean the surface with every flush.
Urinary stone forms faster on rough surfaces, so do not pour hot waste into the toilet so that microcracks do not form.
If you have a very old damaged toilet, then the problem will not be solved so simply, you need to buy a new one with a glossy surface.

Cleanliness in the toilet is one of the priorities of a conscientious hostess. All items in the bathroom are kept clean not only for aesthetic reasons, but also for hygiene purposes. The toilet is no exception. This item of plumbing must be washed from ordinary daily dirt and periodically arranged for a general cleaning: wash all parts of the device (cistern, lid, toilet seat, etc.) and prevent the appearance of rust, stone, and plaque. Otherwise, the toilet will become a breeding ground for bacteria or even become clogged and cause a lot of unpleasant trouble. There are many ways to clean surfaces from dirt.

How to clean the toilet

Today, the range of cleaning products for plumbing is very wide. But in addition to household chemicals, there are folk recipes for compositions. We list the main folk and professional means.

Folk remedies

Folk recipes for cleaning the toilet are designed primarily for regular care. Old deposits and pollution will require special professional tools.

Vinegar. Heat a solution of 9% vinegar to 40 - 50 degrees, after covering the container with a lid. For the procedure, one glass of 250 ml is enough. Add one tablespoon of soda and a drop of iodine. Pour the toilet with this solution or apply a damp cloth to the dirty place. Wait two to six hours and proceed to remove the dirt. This product is suitable for removing lime scale, as the acid corrodes mineral deposits.
Vinegar helps in the fight against limescale on the walls of the toilet
Lemon acid. Citric acid, like vinegar, will help get rid of plaque and urinary stone. Cover the dirt with citric acid crystals and leave overnight. The powder should not remain completely dry, it is necessary that the acid is wetted to the consistency of gruel. The amount of the product depends on the area of the dirty place. If citric acid did not help from the first application, you can repeat the procedure. Some housewives advise adding wood ash to citric acid, which will give the effect of foam.
Crystals of citric acid will serve as a cleaner for the toilet
Baking soda. Baking soda helps to get rid of dirt on various surfaces. It can also be used to clean the toilet bowl. Sprinkle baking soda on dirty areas and leave overnight. In the morning, thoroughly treat the stains with a brush or sponge and rinse with water. Repeat as needed. Another way to clean with baking soda: pour baking soda on the surface to be cleaned and wait half an hour. Then pour in the vinegar and, while the reaction is going on, wipe with a brush. Soda will help in the fight against greasy deposits and disinfect the surface, while acetic acid will cope with limescale and rust.
Baking soda is an all-purpose cleaner
Coca Cola. Finally, to make the toilet shine, you can pour the well-known cola into it, which includes phosphoric acid. She will remove plaque and stone. It is better to fill in at night, so that the remedy is guaranteed to work.
Mustard powder. Mustard is perfect for everyday cleaning - it disinfects and washes off the greasy film. Mix dry mustard (1 tbsp.) With starch (100 gr.) And citric acid (1 tbsp.). Add water to make a slurry and apply to the walls. After a couple of hours, wipe with a sponge. Mustard cannot cope with old plaque and rust, therefore, with a thorough cleaning, it can only be added as a disinfectant.
Mustard powder can serve as an antimicrobial agent

professional tools

The composition of special tools includes strong acids, alkali or chlorine. Therefore, before using them, take care of your safety: put on rubber gloves, protect your respiratory organs. Unlike folk "soft" cleaners, professional household chemicals quickly cope with dirt on the surfaces of the toilet, acting more aggressively.

Oxalic acid. The product is sold in pharmacies and hardware stores. Apply this powder to a wet rag and rub the contaminated area. If possible, pour the acid into the toilet and leave it overnight. There are also professional products based on oxalic acid - Sanoks Ultra, Sarma - gels of domestic production.
Oxalic acid corrodes deposits on the walls of the toilet
Orthophosphoric acid. A 5-7% solution of this acid will do an excellent job of removing dirt in the toilet bowl. Moreover, this tool can be poured into the tank. Plastic pipes will not be damaged when using phosphoric acid. Pour acid into the toilet and cistern for 15 minutes, then wipe thoroughly and flush. This product removes rust and limescale. But you can buy a miracle reagent in car dealerships or in stores specializing in radio products, since phosphoric acid is used for soldering for its intended purpose.
Phosphoric acid helps eliminate rust
Chlorine. Quite often in public toilets we encounter a pungent smell of chlorine. This is not surprising, since chlorine has antibacterial properties and is excellent at bleaching, which is why it is used in common areas. But at home, it is not recommended to regularly use chlorine for cleaning, because it can damage the ceramic surface of the toilet bowl, and is harmful to health. But in isolated cases, such a tool can still be used. Especially if you need to properly disinfect and whiten the bowl. The well-known bleach based on chlorine "Whiteness" is suitable for everyone. Apply "Whiteness" on the surface, and after half an hour wipe with a brush or sponge and rinse with water.
Whiteness bleaches and disinfects
Hydrochloric acid. There are tips on the Internet for using a hydrochloric acid solution, but in its pure form it is very dangerous, so we recommend using only products based on it: Silit Bang, Toilet duck, Domestos. In addition, all professional products are equipped with a convenient thin spout for cleaning the surface under the rim and have a thick gel consistency. In addition, many packages with factory products have child protection.
Domestos contains hydrochloric acid
Pemolux. Pemolux is a soda-based cleaning powder. The composition of Pemolux also includes marble chips, surfactants and fragrances. The effectiveness of Pemolux is achieved due to the abrasive structure. Therefore, it is good for them to clean plaque and urinary stone. Before using the powder, pump out all the water from the toilet. Pour the product on dirty areas and rub with a sponge. The downside is that the powder scratches the surface, and dirt is further clogged into microcracks.

Do not use electrolyte for cleaning, as some sites advise. The risk of getting a chemical burn outweighs the possible effectiveness.

It is worth noting that if you have a colored toilet, then you should not use products with citric acid and chlorine. They can bleach the surface or leave streaks.

To summarize: folk remedies are safe, but require a lot of effort and time to cleanse. Special tools are hazardous to health, but when used correctly, they clean more efficiently and faster. The choice is yours.

How to wash the toilet properly

When the tool is selected, proceed to cleaning.

Tools

For washing you will need:

Let's start cleaning

To be satisfied with the results of cleaning the toilet, follow the following procedure:

Clean everything around the toilet to avoid splatter. Do not place your funds and tools on the tank: they may simply fall inside.
Before cleaning the toilet bowl, remove water from the toilet with a plunger.
If sand has accumulated inside, which is not washed off by a simple drain, try pouring a bucket of water at the same time as draining and work with a plunger. The sand must go.
Wet the inside of the toilet bowl with warm, but not hot, water. This will make it easier for your product to deal with dirt.
Apply the cleaner to the dirty areas inside the bowl, not forgetting the surface under the rim. The time to wait after application depends on the type of product, but not less than 30 minutes. This is necessary to disinfect the toilet bowl.
While the product is in effect, we proceed to cleaning the outer surface. Start at the top: wipe the tank, handle, lid. To do this, use the same tool as for the inside of the bowl.
Wash the seat thoroughly and wipe it dry.
Apply the product to the hinges on which the seat is attached and clean with a hard sponge or brush. An ordinary rag will not be able to reach all sections of the loops.
After the seat, wash the glass - the lower part.
Next, we return to the inner surface and, using a brush or sponge, rub the product and clean it from dirt. Be sure to clean under the rim, where a lot of dirt and bacteria accumulate. Then we wipe the bottom of the bowl, and then we clean the drain to the bottom.
Close the lid and drain the water with the remnants of the product.
After cleaning, do not leave the brush wet in the tray, but dry it by placing it under the toilet lid - the water will drain into the bowl. This way you will avoid the growth of bacteria in the tray and the unpleasant smell in the toilet.

Preventive measures

In order not to have to deal with rust, stone and plaque, prevent their appearance by following these recommendations:

do not allow a direct flow of water, for this, make sure that the drain tank is in good condition;
do not throw food leftovers into the toilet, especially fatty waste;
use devices that maintain cleanliness at each drain - discs, tablets, containers with washing gel, attached under the rim;
Wash the toilet bowl with a cleaning agent at least once a week.

Toilet cleaning. Video

To ensure that plumbing always pleases the eye and does not become a source of disease, clean the toilet regularly, using adequate means and methods. And timely prevention will save you from additional efforts when cleaning the toilet.

The condition of the toilet directly depends on how carefully they are used. Any plumbing product requires special care. In order for you not to have to look for an answer to the question of how to remove a stone in the toilet bowl, you should follow all the requirements for the operation of the product. Neither limescale nor urinary stone appear in one day. Such defects are formed gradually due to improper operation of the toilet bowl. So how to wash the toilet with your own hands?

Formation of a urinary stone

Rare hygienic cleaning of the product leads to the formation of a urinary stone on the rim of the toilet bowl, as well as on the drain hole. In addition, the cause may be an irregular pressing of the toilet flush button. Usually families with small children have to face such a problem. The thing is that untimely flushing of urine leads to the deposition of mineral plaque on the walls of the drain hole. Subsequently, its density increases, a urinary stone is formed. It is absolutely impossible to clean such a formation with a brush. Your usual household detergents are also unlikely to help remove them.

limescale

The reason for the appearance of limescale is the degree of hardness of the water, as well as its chemical composition. Timely hygienic cleaning of plumbing will prevent such formations, and you will not have to deal with the issue of removing a stone in the toilet. In addition, do not forget about special products designed to soften water.

Another reason for the formation of urinary stone or limescale can be a damaged surface of a plumbing fixture. Typically, such defects occur due to improper use of the product. Few housewives know that hot liquid poured into the toilet bowl can cause microcracks to appear on it, in which plaque buildup begins.

How to clean the toilet

In the case of relatively unsettled plaque formed by urine or lime, less complex cleansing measures can be dispensed with. In order to wash the toilet and remove the urinary stone, you should remove the water. This can be done using a plunger or a regular cup with a handle. For further actions, you can use any means for washing the toilet. Apply the composition to the walls of the product and leave it in this state for at least an hour. If necessary (if you chose a liquid detergent, it will drain), you can repeat its application several times. After that, a thin, unsettled coating of urine and lime can easily be cleaned with a brush.

Cardinal methods of washing plumbing

To work, you may need:

hard brush (non-metallic);
gloves;
vinegar;
baking soda;
white;
lemon acid.

If the limescale and urinary stone in the toilet have formed a thick layer of compacted, ordinary detergents will not help here. How to remove a stone in the toilet without damaging the surface of the product? Washing using coarse metal brushes, as you understand, is not recommended. There are more gentle methods for cleaning the toilet.

How to remove stone using vinegar. In order to remove a stone in the toilet bowl, 9% vinegar is often used (apple vinegar is also possible). A glass of vinegar should be heated to about 40ºС. In order not to breathe in a pungent odor, cover the container with a lid. Pour baking soda into heated vinegar, you can add a little iodine. Pour the prepared composition into the toilet. It is advisable to leave the vinegar overnight so that the stone is completely dissolved. If necessary, you can repeat the steps until you get the desired result.
Removal of urinary stone with the help of whiteness. First you need to remove all the water from the toilet. Next, pour out a bottle of the product and leave it overnight. If the result suits you, rinse the plumbing fixture with warm water. If plaque remains, repeat the procedure.
How to wash a plumbing fixture using citric acid? In addition to the above means for washing the toilet bowl, this method is also suitable. For one procedure, two sachets of the product will be enough. Pour citric acid into the toilet and close the lid. In three hours, the stone should partially dissolve. Most likely, it will not be possible to completely get rid of contaminants in one procedure. You should repeat the steps until the toilet is completely clean.

The heaviest pollution and means for their purification

Depending on the chosen method, you may need:

rubber gloves;
protective glasses;
respirator;
hard brush;
brush;
oxalic acid;
battery electrolyte.

The use of technical oxalic acid. How to wash the dirt in the toilet, formed over several years of operation? Cleaning with ordinary household detergents is absolutely useless here. In such cases, you can use technical oxalic acid. This product is sold in the form of a dry powder. Before using it, carefully read the instructions on the package. When working with oxalic acid, all safety precautions must be observed. All the following actions are carried out strictly with rubber gloves. Apply the powder to a wet piece of tissue, after which they should wipe the formation of urinary stone. You can also dissolve technical oxalic acid in the toilet itself and leave for an hour. But keep in mind that this option will require a much larger amount of powder. After the procedure, it is necessary to thoroughly rinse the toilet.
Using an electrolyte to remove the stone. The use of an electrolyte is considered the most effective method for removing an old urinary stone. But working with electrolyte requires the most serious safety measures. Procedures are carried out in goggles, gloves and a respirator. It is very important not to splash the electrolyte when pouring into the toilet. This method of cleaning the toilet bowl is used for extremely heavy pollution. Please note that if your plumbing pipes are made of plastic, electrolyte is contraindicated.

In addition to all methods, you can use Coca-Cola as a toilet cleaner. The method of removing urinary stone using Coca-Cola is quite effective. How to clean the toilet bowl using this product? To do this, pour two bottles of Coca-Cola into it. Leave in this state for several hours, after which, using a brush and household detergents, remove plaque.

Categories

Popular