How to clean the toilet from rust, urinary stone and limescale? How to easily clean the toilet, remove rust and limescale? How to remove deposits in the toilet

Every housewife dreams of her house shining with cleanliness. But the modern life of women does not always provide this opportunity. Work, children, family - now there is absolutely no time for cleaning. If the toilet is not cleaned for a long time, a urinary stone may form on its surface. A urinary stone is a build-up of minerals that, along with urine, get on the walls of the toilet. Usually, a urinary stone forms under the rim of the toilet, as well as in the place of stagnant water.

Why does a urinary stone form?

Most often, a urinary stone is formed on the toilets with untimely and insufficient draining. This is especially true in families with small children. Babies don't always remember to flush and the minerals from the urine eat into the walls of the toilet bowl.
If the drain barrel is defective, this also contributes to the formation of limescale and urinary stone.
Plumbing with a defect or a rough surface is an ideal place for the accumulation of dirt, germs, plaque and stone.
Old toilets with a long service life are most prone to the formation of urinary stone.

The urinary stone tends to grow and increase in size. If you do not fight it, it significantly narrows the lumen of the toilet bowl and pipes. Therefore, if you are faced with such a problem, you do not need to delay its solution. With a urinary stone, you need to fight here and now!

First you need to drain the water from the toilet. This is easy to do with a mug with a handle - just scoop out the water. After all, any tool works much more effectively without water.
Then put on gloves and a respiratory mask. Most modern chemicals are quite aggressive.
Take any cleanser that says on the label that it can fight urinary stones. For example, Toilet Duck, made from hydrochloric acid, is very effective even in still water. In the line of household chemicals Domestos there is a special tool designed specifically for urinary stone. According to the manufacturer, this tool completely destroys even chronic one-year-old growths. Very effective in the fight against urinary stone and Cillit, its effectiveness is noted by many housewives. Another powerful household cleaner is Mr. Muscle in granules. It not only cleans the toilet from urinary stone, but also whitens the surface. The choice of professional household chemicals is up to you.
Apply the product of your choice to the rim of the toilet bowl and to the places where the urinary stone has grown. Leave for a couple of hours. You can't use the toilet during this time.
After the indicated time, rub the walls and rim of the toilet with a brush. It is better not to use metal brushes, they can scratch the plumbing, which leads to the re-formation of plaque.
Of course, it will not be possible to get rid of a dense and thick coating at a time. If necessary, the procedure can be repeated. Thus, over and over again, you will get rid of the thickness of the urinary stone until you remove it completely.
Please note that children and animals must not be in the bathroom during treatment. Chlorine-containing household chemicals are very toxic.

How to get rid of a urinary stone with improvised means

If there are no specialized gels at hand, you can use what you have at home. Here are some effective ways to get rid of urinary stones.

Vinegar. This is a great recipe for removing a urinary stone. For this we need vinegar, baking soda and iodine. These ingredients can be found in every home. A glass of vinegar must be slightly warmed up. Take not very strong, 9% is usually enough. Be careful - do not inhale the vapors of the heated liquid. After that, add a spoonful of baking soda and a teaspoon of iodine to the hot vinegar. Mix the composition and pour it into the toilet. It is best to do this at night so that the prepared remedy has time to take effect. In the morning, go over the toilet with a brush and rinse everything thoroughly.
Bleach. This is a very aggressive and very effective remedy for fighting urinary stone. However, it does not work in water, it must first be scooped out. Pour a glass of any chlorine bleach and leave for a few hours.
Lemon acid. This is another effective way to get rid of plaque. You don’t need to do anything, just pour 3-4 sachets of citric acid into the toilet. Leave for a while. This will not completely remove the stone, but small growths can be easily removed.
Bleach. Buy a bag of bleach and pour it down the toilet. It is best to leave the product overnight. Chlorine not only helps to destroy the stone, but also disinfects the surface, which is also important. In addition, after chlorine-containing products, the toilet bowl will again shine with whiteness, like new.
Anticalc. This is a universal remedy for removing any type of plaque - scale, urinary stone, calcareous formations. Pour a packet of this powder down the toilet at night. In the morning you will find that the urinary stone has begun to fall off by itself, in pieces. Residues of dirt will need to be cleaned with a brush or brush.
Oxalic acid. This tool is suitable for hard-to-remove and chronic growths. Oxalic acid can be purchased at hardware stores and is a white powder. When using oxalic acid, it is very important to wear a respirator and gloves, as the agent is very toxic and corrosive. If the urinary stone is localized only at the drain site, the acid must be poured into the water. If the stone has formed on the rim of the toilet, you need to put a little powder on a cloth and gently wipe the contaminated areas. Leave the toilet for a while, then once again walk on it with a brush and press the drain button.
Carbonated drinks. This is a modern, but very effective means of getting rid of urinary stones. Take a couple of bottles of Coca-Cola, Sprite or Fanta and pour it down the toilet. Leave for three to four hours. A high concentration of citric acid breaks down the stone and cleans the toilet bowl.
Electrolyte. This is the most thermonuclear remedy for urinary stone. The electrolyte is used in car batteries, but it perfectly destroys various kinds of growths. However, before applying, you should make sure that all pipes of your sewer system are metal. Plastic pipes may be damaged. So, pour some electrolyte down the toilet and let it sit for a couple of hours. After that, proceed similarly to the previous methods - clean and rinse.

It is worth noting that urinary stone appears on running plumbing when the toilet is not cleaned for a long time. Therefore, in order to avoid such growths, you need to regularly, at least once a week, clean the toilet bowl with prophylactic agents. Any household chemicals will cope with a small amount of pollution. To do this, just pour a little chlorine-containing product on the rim of the toilet, and then rinse everything with water.

Also pay attention to the serviceability of the drain tank. If the water flows constantly, it contributes to the formation of calcareous and urinary stones. This is especially true in regions with hard water. To soften the water, you can put a small filter in the tank that will protect the toilet from various kinds of growths.

An excellent prevention of the formation of urinary stone are special plates and tablets that are attached to the inner wall of the toilet bowl. With each drain, the surface is cleaned and disinfected, which is important for general hygiene.

As noted, urinary stone is formed on rough surfaces, in places of chips and cracks. To avoid this, you need to protect the surface of the toilet and do not clean it with abrasive products. Do not pour the remains of hot food into the toilet bowl - it can cause the formation of microcracks.

An old, damaged toilet is a potential site for a urinary stone to build up. Having eliminated it once, be prepared for its reappearance. To avoid constant struggle, you need to buy and install a new toilet with a glossy surface. Monitor its condition, clean its surface regularly, and urinary stone will not bother you anymore!

Video: how to wipe the toilet in 15 minutes from a one-year-old urinary stone

The mess in the bathroom will not leave indifferent any housewife. The catchphrase "The toilet is the face of the hostess" has not lost its relevance in our days.

Often you have to deal with the fact that even with regular maintenance of plumbing, the surface of the toilet bowl darkens, rust spots and traces of limescale appear on it. How to clean the toilet from dirt yourself? How to remove urinary stone, plaque and rust? What cleaning solution or powder should I use to get my toilet to a shine without damaging the surface? First you need to understand how certain types of deposits are formed.

Why is plaque formed in the toilet

The main "enemies" of cleanliness in the bathroom and the impeccable appearance of plumbing include urinary stone, limescale and rust. Let's take a closer look at the problem:

The formation of a urinary stone is a serious and intractable problem for those who do not know how to deal with it. Deposits form at the bottom, where water accumulates. Urinary stone is a complex compound based on the mineral salts found in human urine.

As a result, a persistent brown coating forms on the bottom of the toilet bowl, and when there is a lot of deposits, this can also lead to a decrease in the diameter of the drain hole. For this reason, it is necessary to get rid of a urinary stone immediately after its appearance.

The appearance of limescale is due to the calcium salts that tap water contains. The more of these compounds, the higher the hardness of the water and the more abundant deposits.

Plaque forms on the inner surfaces of the toilet bowl, as well as in the cistern. Lime deposits are an ideal "basis" for other types of pollution, and to prevent this from happening, it must be removed immediately.

Rusty streaks on plumbing appear due to poor water quality and poor condition of water pipes. If the system is old, and a large amount of rust has formed inside, its particles, along with water, fall on the surface of the plumbing, forming orange-brown streaks. It should be remembered that the “older” the stains, the more difficult it is to remove them, and to clean them in a timely manner.

How to clean the toilet from urinary stone, rust stains and lime deposits? Dealing with dirt on the surface of plumbing is not difficult if you know how to do it and act in accordance with the rules.

How to clean the toilet from a urinary stone at home

Cleaning the toilet from plaque, rust and urinary stone will be most effective if you follow these recommendations:

Remove water from the toilet. It is enough just to scoop it out with a small mug, and the remnants can be “wet” with a rag.
Protect the skin of the hands with gloves, and the respiratory tract with a medical mask.
Apply the selected cleaner to the surface and leave for the amount of time required according to the instructions.
Clean the rim and walls with a brush. It is better not to use brushes with a metal base, this will lead to scratches on the surface.
After cleaning, rinse the toilet several times by flushing the water from the tank.

Be prepared for the fact that dirt may not disappear after the first cleaning. If necessary, manipulations will have to be repeated several times.

How to remove a stone in the toilet with folk remedies

If you need to tidy up your plumbing, you can use a number of products that will help not only remove plaque, urinary stone and rust, but also return the lost shine and whiteness to the surface.

Cleaning chemicals

In household chemical stores you can choose the necessary product, a variety of gels, liquids and powders are presented in a wide range. How to wash the toilet with a store-bought product? You will only need to carefully follow the instructions, and the problem of cleanliness in the bathroom will be solved.

However, many housewives avoid the use of special tools. This is due to the high cost of chemicals, as well as strong toxicity. In such a case, there are a number of folk remedies that can be used without fear of harming your health.

Baking soda

This tool perfectly copes with pollution on plumbing equipment and is suitable for cleaning the toilet bowl from various contaminants. Pour a pack of baking soda into the previously "dehydrated" toilet and leave it overnight. You can carry out these manipulations in the morning, before leaving for work. The main thing. To not use the toilet for 8-10 hours.

After the specified time, clean off the dirt with a brush, and rinse off the remnants of the product with water. Soda not only has the ability to eliminate various kinds of pollution, but also whitens the surface.

Warm vinegar solution

Heat 1 cup of 9% vinegar and pour it into the toilet without water for 2-3 hours, then clean the surface from stains. Vinegar is effective against limescale and also dissolves urinary stone.

To achieve the maximum effect, you can make such a toilet bowl remedy with your own hands: add iodine, soda or salt to the vinegar solution (in the proportion of 1 teaspoon of the product per glass of vinegar). In this case, you need to withstand the product for at least 8 hours.

Lemon acid

Empty the toilet bowl and pour 2-3 tablespoons of acid into it. Leave the product for 3 hours, then clean with a brush. The procedure will need to be repeated several times to get rid of plaque and urinary stone.

Citric acid will not only remove dirt, but also unpleasant odors. With it, you can make your own toilet freshener. Just dissolve a couple of tablespoons of the powder in 1 cup of water and treat the surface.

Acetic essence

If the vinegar solution has not coped with the pollution, you can use a 70% concentrate. Remove the water from the toilet and pour the essence inside. After 3 hours, clean the surfaces with a brush and flush the water several times to wash away any remaining caustic.

"Coca Cola"

A drink of little use for quenching thirst, however, it is very useful in the household. It will also help with cleaning the toilet bowl.

Pour 1.5–2 liters of drink into the toilet at night, during which time the caustic substances will loosen the plaque, and you can easily remove their remnants with a brush.

These products are effective provided that plumbing is cleaned regularly. But what to do with strong and old deposits? There are several "serious" means.

How to clean rust, plaque and old urinary stone in the toilet

In the case when gentle means turned out to be ineffective, you can use "heavy artillery" in the form of aggressive chemicals.

Iodine monochloride

This substance can be bought at a veterinary pharmacy. Pour the solution on dirt, and after 1-2 minutes, rinse with water from the tank. This time is enough to remove plaque, urinary stone or rust. If necessary, remove the remaining dirt with a brush.

It is important to know that the use of iodine monochloride is not recommended in cases where the sewer pipes are cast iron or aluminum.

Hydrochloric acid

Hydrochloric acid can be purchased at a plumbing store. Pour the liquid into the toilet bowl and let it sit for 30-50 minutes. Rinse off the remaining substance with water from the tank, and clean the toilet with a brush.

The tool is undesirable to use if the works of the sewer system are plastic.

Acid battery electrolyte

Any unwanted stains and deposits will disappear if the electrolyte is used. Apply the substance to the dirt, and leave for 1 hour. After several times, flush the water to wash off the residue, and brush the surface with a brush.

This tool can cause significant damage to plastic pipes, so in homes where the system is made of this material, it is better not to use electrolyte for cleaning toilet bowls.

Dry oxalic acid

This substance is actively used by the chemical industry and is a fine powder. Removal of stains and plaque is carried out as follows: the acid is applied to a rag and the resulting dirt is wiped off, after which the residues are washed off with water.

You can do it differently: pour dry acid into the toilet with water and leave for 20 minutes. Then drain the water and clean the surfaces with a brush.

When you work with these substances, be sure to protect your hands with gloves and wear closed clothing. You should also wear a medical mask or respirator, as toxic fumes can cause serious harm to your health. It is better to leave the door to the bathroom open, and open the windows in the room closest to the toilet.

The best way to solve a problem is to prevent it. Of course, it is impossible to avoid the appearance of deposits, but it is quite possible to make sure that their number and intensity of appearance are significantly reduced. Use the following guidelines:

Unfortunately, even the cleanest housewife is not immune from dirty plaque on the walls of the toilet. It is sometimes very difficult to clean it - limescale and urinary stone deposits are very firmly eaten into the enamel surface. Therefore, it is necessary to know how to quickly and effectively remove all contaminants from the walls of the toilet bowl.

Causes of pollution

The water that enters our homes and, in particular, the toilet tank, can hardly be called clean. It has a lot of impurities and, often, it is very tough. It is the hardness of the water that leads to the fact that limescale begins to appear on the walls of the toilet bowl. In addition, if the toilet bowl is not cleaned after each use, over time, urinary stone deposits are added to the limescale. This contamination is a plaque of yellowish minerals. It accumulates mainly under the rim of the toilet bowl. Added to these two problems is the rust that comes out of the tank with every flush.

Over time, the enamel of the toilet bowl becomes rough; if aggressive and abrasive substances are used to clean it, various defects may appear on the enamel. Such a surface becomes dirty even faster, and it is much more difficult to clean it. Therefore, it is very important to properly care for the toilet from the moment you buy it.

General rules for cleaning the toilet

Whatever means for cleaning the surface of the toilet bowl you choose, you must be guided by a few general rules:

First of all, before starting work, you need to put on gloves on your hands. This is necessary in order to protect the skin from exposure to aggressive chemicals, as well as for reasons of hygiene;

It is necessary to clean the entire surface of the toilet bowl. Therefore, before using the selected detergent, you need to completely get rid of the water at the bottom. To scoop up water, you can use a jar, disposable cup or syringe. Dry the rest with a rag;

To effectively remove dirt from the walls of the toilet, you must carefully read the instructions for the cleaning agent. Keep the product on the walls of the toilet for as long as the manufacturer advises. If you decide to use home cleaning products, then, in most cases, they should be left overnight. This rule does not apply to the use of very aggressive substances (for example, electrolyte) - it should be used only in extreme cases and kept on the walls of the toilet for a short time.

How to clean the toilet with folk remedies

Sometimes it happens that you need to clean the toilet, but there are no suitable household chemicals at hand. In order not to have to run to the store and waste your money and time, you can use those improvised means that you will probably find at home. Moreover, the result from their use is often no worse than from purchased chemicals. Let's look at what home remedies can be used to clean the toilet from pollution.

How to clean the toilet with household chemicals

To date, the shelves of the household departments are littered with various cleaning products specifically designed to remove difficult dirt from the walls of the toilet. Cleaning agents containing hydrochloric acid showed themselves best in the fight against plaque on the toilet bowl. Alkaline-based cleaners are just as good, but they're better for fresh stains. It will not be so easy for them to cope with an old raid. And it is best to apply alkaline cleaners for a long time (for example, at night) - then the effectiveness will be much higher.

Most often, liquid bottles are equipped with a special spout, with which it is easy to process the surface of the toilet bowl under the rim. After applying such a product, you must wait about an hour for all the main plaque to come off (check the time in the instructions for the product). Then it remains only to treat the surface with a brush and rinse off the water. With strong old pollution, in order to obtain the desired effect, the cleaning procedure will need to be repeated 2-3 times.

Cleaning the toilet with harsh chemicals

Sometimes pollution is so strong that all household and folk remedies cannot cope with them. In this case, in order to clean the toilet with high quality, it is necessary to use stronger means. When using them, care must be taken not to neglect rubber gloves, as there is a risk of serious chemical burns during operation. And remember: aggressive substances should not be left on the walls of the toilet for a long time, as this can damage the surface. So, how else can you clean heavy dirt on the walls of the toilet?

How to prevent urinary stones

It is always easier to prevent the formation of complex contaminants than to get rid of them. Following a few simple rules will allow the toilet to always remain snow-white.

Be sure to monitor the serviceability of the drain mechanism - water should not continuously run into the toilet. If the drain works properly, this reduces the formation of limescale. When choosing a new toilet, pay attention to models that have two buttons - so you can control the volume of flushed water yourself.
Buy a special product from the hardware store that softens the water and disinfects the surface with each flush. Usually they are released in the form of tablets that fall into the tank. And you can buy a tool that is attached under the rim of the toilet.
Use a brush regularly - it is advisable to walk it on the surface after each visit to the toilet.
Use a detergent to clean the toilet bowl at least once a week. This way you can avoid the formation of a strong plaque.
Remember that on a damaged rough surface, plaque builds up much faster. Therefore, when cleaning, it is not recommended to use strong abrasive substances.

If your toilet is already old, scratched, and the surface has become rough, then the easiest way is to replace it with a new one. When buying a new toilet, remember that only proper care and regular cleaning will help maintain its original whiteness.

If the toilet is cleaned in a timely manner, the condition of this plumbing fixture will always be good.

You should not only follow the rules of operation, but also use special tools to remove corrosive dirt, such as urinary stone.

Article content:

Reasons for the appearance

The main factors for the appearance of urinary stone:

Urinary stone accumulates in large numbers insufficient cleaning of the toilet bowl.
In some cases, the reason is irregular drain, which is an actual problem for families with small children. If regular flushing is not carried out or occurs in insufficient quantities, mineral deposits appear on the inside of the toilet bowl. When it becomes hard enough, it is much more difficult to remove it, as it turns into a urinary stone. Neither a brush nor standard household products can cope with these deposits.
One of the most common causes of a urinary stone with regular plumbing maintenance is coating damage. If you do not clean or use the device according to the instructions, there is a risk of unpleasant consequences that will appear even after the surface has been completely cleaned. The final solution to this problem can only be updating the protective coating.

Cleaning methods

To clean the surface of any household appliances from plaque, it is necessary at the first stage to remove the liquid from the internal structure. To do this, you need to use a plunger. In the absence of this element, you will have to use a glass with a handle.

Only after bailing out water or piercing the system should detergents be used. A special liquid is evenly applied to the surface, and then left for about 60 minutes.

If during this time the plaque has not succumbed to the splitting processes, it is necessary to re-apply the agent, and then use a brush or similar object to remove the plaque. The older and thicker the deposits, the stronger the funds will be required.

All methods of cleaning the toilet from urinary stone are reduced to the use of one of the following varieties of funds:

Household chemicals purchased at a hardware store or supermarket.
Folk remedies that can be made from materials already in the house.

Purchased cleaning products

abrasive powders. The most famous of this group of funds is Pemolux. Using these elements is quite simple. You should perform the following actions:

Clean the plumbing fixture of liquid.
Wear thick enough rubber gloves.
Pour the powder onto the surface and spread evenly over its entire length.
Using a brush or other brush-like element, clean the surface of all contaminants.

It's pretty hard work. The presented method is not recommended for faience coating, as it may lose its smoothness and become covered with small cracks.

The same negative effect is possible for other types of surfaces, so you should clean the toilet carefully. If microscopic cracks are allowed to appear, dirt will accumulate in them.

Alkaline funds. Of this group, "Whiteness" and "Domestos" are most often used. The composition of these funds is characterized by the presence of caustic soda. It acts directly on the urinary stone, completely dissolving it. Residues of harmful substances after applying the product can be removed with a brush, after which it is necessary to pour plenty of water on the cleaned places.

To use this tool correctly, you must follow these steps:

Fluid is draining from the toilet.
The solution is distributed over the entire surface contaminated with urinary stone.
After half an hour, it is necessary to wash off the product.
If dirt remains, the above steps must be repeated again.

Alkali is able to achieve complete dissolution of the urinary stone. These funds must be used carefully. You should check the condition of the tank. If it leaks even a little, it is necessary to turn off the water for a while.

Means with acid in the composition. This group includes Silit, Duckling and Comet. These tools must be used according to the principle that is relevant for alkaline solutions. Often, acid-based substances are produced with an antibacterial effect. Their use allows you to get rid of not only the urinary stone, but also the infection.

Folk methods

To ensure the toilet is in impeccable condition, you can use folk methods.

The toilet bowl is bleached, disinfected and cleaned not only with the help of purchased products, but also with the use of substances that almost every housewife has.

Alkali

Recently, the use of caustic soda has become widespread. With its help, any pipes are cleaned, even from severe blockages. Together with the urinary stone, the toilet bowl is cleaned of fat, since this chemical agent is able to dissolve organic matter.

To clean the toilet, you must put on high-quality rubber gloves in advance, and then do the work, carefully distributing the product over the surface. Often housewives make a choice in favor of purchased gels, which contain alkali.

If the surface is excessively contaminated, you must use the following algorithm of actions to clean it:

Remove all liquid from the toilet. If there are no special plumbing fixtures, it is fashionable to simply scoop out the water.
Gel or liquid with alkali is poured.
You have to wait a few hours for it to take effect.
The surface is thoroughly cleaned with a brush.
You should use a toilet flush to remove the alkaline product with excess dirt.

The yellow-brown crust is a urinary stone. This plaque is best removed with alkali. Other means work worse. Together with this crust, you can simultaneously get rid of rust and other contaminants.

Acid

This product is also great for getting rid of dirt. The toilet bowl is cleaned of the most corrosive substances, so the complete elimination of urinary stone with the correct use of the product is guaranteed. If you leave it for a long time, the top layer of the coating may partially come off.

It is advisable to constantly check the degree of cleanliness of the toilet bowl, trying to remove the dirt with a brush in order to remove the product after it has been completely eliminated. It is necessary to add water to the mixture every 5-10 minutes or rinse and reapply.

Usually homeowners use vinegar essence for various purposes, so almost everyone has it. Sulfuric acid can be obtained from the battery, as it is necessarily contained there to maintain the function of the electrolyte.

Bleach

To remove dirt and bacteria from the toilet along with the urinary stone, you can use a solution of ordinary bleach. This substance has excellent whitening properties, however, to achieve maximum results, you will have to work the surface with a brush.

To remove traces of urinary stone, you can use a pumice stone. Cleaning the toilet with an ordinary pumice stone is not very convenient, so it is advisable to purchase a special device on a stick. You can wear gloves while doing this.

When bleach is mixed with abrasive, a better stain remover is hard to come by. In rare cases, plaque remains. In this case, you will have to additionally clean the surface with acid.

What to do in advanced cases?

The greatest difficulty arises when cleaning an old toilet bowl. Its surface is rough, as there are scratches, roughness, and sometimes chips. Even with regular and sufficiently high-quality cleaning, constant pollution leads to the formation of an indelible urinary stone. Usually, only replacing the old plumbing fixture with a new one helps.

To whiten the inside of the toilet, you can use "Coca-Cola". Pour the drink into the container and wait a few hours. When using this or a similar strong agent, the following must be observed:

To protect yourself from inhaling fumes, you should work without leaning over the toilet, or use special masks.
Put on high quality rubber gloves.
Cleaning liquid should not spread over the skin, and should not be allowed to get into the eyes.

The easiest home remedies to use

If a person has developed an allergy to chemicals, you will have to clean the toilet without them. Can apply soda, without dissolving the substance in the liquid. First, remove the water from the container using a small glass or similar element. The remaining liquid must be removed with a rag. Soda is poured abundantly on the surface, after which it should be rubbed with a brush.
To remove the stone with improvised means, it will come in handy vinegar. It is poured into a container, measuring one glass of liquid, and then heated to a temperature of 35-40 degrees. A small amount of soda or iodine should be added to the mixture. The solution must be poured into the toilet and left for a long time, for example, overnight. In the morning, the deposits will be completely dissolved.
Lemon acid copes with any type of plaque, including urinary stone. Enough 2 packs of purchased funds. The substance must be completely poured into the toilet, wait about 2-3 hours with the lid closed, and then open it and see the result. To remove strong deposits, it is necessary to repeat these steps several times, and then regularly carry out such cleaning of the plumbing fixture.

Can a urinary stone be prevented?

To prevent the appearance of a persistent plaque of urinary stone and other contaminants, it is not necessary to constantly use strong products. You need to follow some instructions:

Monitor the health of the drain system, if necessary, carry out repairs in a timely manner.
Do not flush down the toilet objects that are not allowed to be placed in relatively thin pipes.
Plaque and other contaminants should be cleaned regularly, blockage should not be allowed.
When performing general cleaning, it is necessary to clean the drain system with the help of special products from a number of household chemicals.

It should be remembered that expensive toilets should be cleaned regularly, as getting rid of heavy dirt can damage the top coating, which will negatively affect the appearance of the item.

More modest furniture also needs to be washed on time so that you do not have to spend a lot of time cleaning.

There are rules in housekeeping that remain unchanged for many generations of housewives. A clean toilet is just one of those. However, maintaining the radiance of plumbing is quite troublesome, even with the huge amount of cleaning products that are offered by the modern market for such products. It is especially difficult to get rid of a urinary stone that turns your toilet into a cluster of mineral growths with a disgusting smell and gray-orange smudges on the surface of the sanitary ware. How to clean it at home?

Where does urinary stone come from in the toilet

In fact, this is a mineral deposit that forms on the walls of the toilet bowl, under the rim and in the place of stagnation of water due to the fact that drops of urine fall on the surface. The growth of a urinary stone occurs because

after using the toilet, not everyone remembers to flush (this problem is especially relevant for families with small children - kids often forget to flush after themselves);
a leaking tank contributes to the spread of mineral deposits;
defective plumbing, for example, with an uneven, embossed surface, provokes the accumulation of microbes, dirt and plaque;
the toilet is too old, which means it is prone to all kinds of damage.

Such a stone is not only an aesthetic problem. The fact is that if you do not fight the build-up, then it can grow to the point that the clearance of the toilet bowl and sewer pipes narrows. That is why it is necessary to start the fight with the stone immediately.

How to clean a urinary stone inside the toilet bowl at home

There are several options for removing urinary deposits from the toilet. First of all, this is a mechanical method: the stone is cleaned from the surface with a knife, a metal brush or sandpaper. However, this option is only suitable for old toilets, that is, “when there is nothing left to lose”: such processing will certainly leave scratches that will grow even stronger over time. So solutions remain for an effective fight. These must be acid-base compounds. These can be found in the lines of professional cleaners or make your own.

Preparatory stage

Regardless of the choice, the surface for cleaning must be prepared.

Instruction:

Drain the toilet and scoop out the rest. To do this, it is convenient to use a bucket with a long handle. This is a very important point, since any cleaning agent will be much more effective if water does not interfere with its action.
We put on gloves - acid-base solutions are very aggressive to the skin.

store funds

Popular among consumers

powders (abrasives) for cleaning - Pemolux, Komet;
gels (they corrode the stone as much as possible due to the fact that they slowly flow down the walls) - Domestos, Toilet duck;
creams (may be combined with powders) - Cif.

Empirically, the three leaders in removing the stone from the drain, from under the rim and from the bottom of the toilet were determined.

Table: the most effective commercial urinary stone removers

Before applying the product, you need to carefully study the instructions and follow them carefully (especially regarding the duration of action!), Otherwise, you can damage the toilet bowl coating and the integrity of the pipes. And one more important nuance: after one cleaning, it is unlikely to get rid of the urinary stone. So the procedure will have to be repeated several times, depending on the degree of neglect of pollution, and then regular preventive cleanings should be carried out. By the way, the latter is relevant for any option for removing the build-up.

It is interesting. It is better to entrust the care of the enamel of colored toilet bowls to industrial products. Some manufacturers even supplement the instructions for use with a cleaning point for colored plumbing. But home cleaning methods can give an unpredictable result, since the chemical composition of the enamel that was used in the manufacture of such a designer toilet model is very important.

improvised means

In the matter of cleaning the toilet, improvised means can be called radical, since they work very effectively, but require even more careful handling. So thick rubber gloves, a respirator (if possible) and a brush (but definitely not metal!) Will be relevant. Here is what the modern rating of the most effective and fastest ways to remove the stone looks like.

First place - electrolyte for batteries

Please note that this method is only used if metal pipes are installed in the system, since plastic can be severely damaged by such cleaning.

Instruction:

After carrying out the preparatory procedures, pour a little electrolyte on the problem area.
We leave for 1.5-2 hours.
We clean the plaque with a brush, wash it off.

It is interesting. An alternative to the electrolyte is hydrochloric or phosphoric acid. For processing, a 33% solution is used, the action time is 15 minutes. But acid will corrode plastic pipes.

Second place - bleach

In this cleaning option, there is one indisputable advantage - after the procedure for removing growths, the surface of the toilet bowl will dazzle with its whiteness.

Instruction:

Pour a bag of bleach into the toilet.
We leave the remedy for the night.
We clean the remnants of the build-up with a brush, wash it off.

Please note that bleach also neutralizes harmful bacteria. An alternative to packaged bleach is "Whiteness". Usually one cleaning takes a standard bottle.

The disadvantages of this method include the duration of exposure, as well as some inconvenience: it is very problematic to pour bleach under the rim of the toilet bowl, so “Whiteness” remains.

Third place - oxalic acid

A white powder, which can be purchased at hardware stores, does an excellent job with old and stubborn urinary stone stains.

Instruction:

Pour the acid into the drain (or use a cloth to “fix” the powder under the rim).
We leave for 1-2 hours.
Rinse off, brushing off residue.

Vinegar, soda and iodine

This composition is easy to apply under the rim due to its consistency.

Instruction:

Slightly heat up 1 tbsp. 9% vinegar.
Add 1 tbsp. l. baking soda and 1 tsp. iodine.
Mix and pour into the toilet.
We leave for the night.
We clean the surface with a brush, rinse.

It is interesting. You can only use soda: it will not be able to completely get rid of the stone, but it will perfectly prepare the toilet bowl for further “war”.

Anticalc

Means in the form of a powder for removing scale, limescale, urinary stone deposits; sold in hardware stores. The application is the same as for bleach. Works well on not too old growths.

Lemon acid

This is a good option to remove small growths; citric acid will be ineffective for old ones. But this way you can only remove the stone in the drain, but to clean the walls and the rim you will have to pick up something else.

Instruction:

Pour out 3-4 packets of lemon.
We leave for 4-5 hours.
We clean the deposits with a brush, wash off.

Coca Cola and Sprite against urinary stone

The action of carbonated drinks such as Cola, Sprite or Fanta is based on their high content of citric acid. Pour 2-3 bottles of the drink into the toilet, leave for 2-3 hours, clean off the plaque and rinse.

It is interesting. As with citric acid, drinks will only work on small deposits. Many cat owners use Cola to remove stone from the walls of the pet's tray, as other means adversely affect the animal's sense of smell. Although experienced cat lovers advise a more drastic way to deal with deposits - replacing the tray.

Video: how to remove a urinary stone with Pepsi

Prevention

In order not to have to look for means to combat old deposits, it makes sense to take care of weekly prevention.

It is interesting. The rough surface of sanitary ware is prone to urinary stone growths, while on glossy walls with regular cleaning there are no such problems.

In order to negate the chances of deposits in the toilet, you can apply

tablets that are placed in the drain tank - fight growths under the rim;
gel blocks that are fixed under the rim - prevent the growth of stone in the drain.

In addition, it is worth remembering the weekly cleaning of the “white friend”, as well as the need to maintain the drain in working order, that is, to prevent leakage in a timely manner. And, of course, you should not clean the plumbing with metal brushes or pour hot food into the toilet bowl - all this provokes the formation of microcracks, from which it is very difficult to completely clean the urinary stone. Another important preventive measure is the absence of stagnation of urine, that is, it must be washed off after each trip to the toilet.

It is possible to clear the "white friend" of urinary stone at home. True, it must be taken into account that acid and alkali should not be recklessly poured into the toilet if the pipes in the house are plastic. In this case, it is better to use more gentle cleaning methods: soda, anticalc, etc., or use professional plumbing care products.

Categories

Popular