Plaster vetonit pro gypsum 30 kg. Weber.vetonit pro gypsum (30kg) white gypsum superplastic plaster, reinforced. When performing manual work,

GYPSUM PLASTER WEBER.VETONIT PROFI GYPS

Gypsum plaster white superplastic.

PURPOSE:

Basic alignment of walls and ceilings in dry rooms with normal humidity, as well as in the kitchen, corridor, bathroom. node (except bathrooms);

Alignment of walls with a layer up to 50 mm (locally up to 100 mm);

Manual and mechanized application;

Suitable substrates: concrete, foam concrete, brick, plastered surfaces, gypsum surfaces.

BENEFITS:

Reinforced with microfiber - up to 50 mm without cracks;

High quality finish surface;

Easy to spread and level;

Crack resistant;

It is superplastic in drawing manually and in the mechanized way.

INSTRUCTIONS FOR USE:

Plaster preparation:

Mixing should be done with a drill with a nozzle for 1-3 minutes until a homogeneous consistency is obtained.

In the process of applying the solution to the surface to be plastered, it is impossible to add water or a dry mixture! It is not allowed to add other components to the solution.

Foundation requirements:

The substrate must be solid, clean, free of dust and dirt. Substances that weaken adhesion such as grease, dust, etc. must be removed. Windows and other untreated surfaces must be carefully protected.

To increase the adhesive strength of the plaster mixture with the base, it is necessary to treat the surface with a weber.prim contact primer. After applying the primer, it must be allowed to dry completely (drying time 24 hours). Avoid dusting the primed surface.

Application:

Spread the prepared plaster mortar on the surface within 30 minutes after mixing with a trowel with a layer of 5-50 mm, locally up to 100 mm. Then smooth the rule with zigzag movements.

When applying several layers, the second layer of plaster is applied without waiting for the first layer to dry completely (after 1-1.5 hours). Plaster ceilings only in one layer no more than 15 mm thick.

As soon as the plaster mortar begins to set (approximately 40 minutes after mixing), level the surface with a metal trapezoid rail or a wide spatula, cutting off the excess and filling in the recesses.

To obtain a smoother surface for decorative finishing (wallpapering, painting), the surface must be treated with finishing and superfinish putties: weber.vetonit KR, weber.vetonit LR+, weber.vetonit LR Pasta.

To achieve the best result, it is necessary to carefully plan the plastering work, taking into account the curing time of the gypsum plaster. During the work, the temperature must be above +10 °C. The water temperature for mixing the dry mix should be between +5 °C and +30 °C.

PRECAUTIONARY MEASURES:

When working, rubber gloves must be used;

Avoid contact with skin and eyes;

In case of contact with eyes, rinse with plenty of water;

Thanks to the use of modern microfibres in the production, weber.vetonit PROFI GYPS has high strength characteristics and special elasticity, which ultimately allows for a high quality finish surface.

• Basic alignment of walls and ceilings in dry rooms with normal humidity, as well as in the kitchen, corridor, bathroom (except bathrooms);
• Alignment of walls with a layer up to 50 mm (locally up to 100 mm);
• Manual and mechanized application;
• Suitable grounds:
  • concrete, foam concrete;
  • brick;
  • plastered surfaces;
  • plaster surfaces.

SPECIFICATIONS

* Gypsum dry mixes can be of various white colors. It depends on the natural impurities in the gypsum stone. The color of the mixture does not affect its characteristics.

COLOUR

Weight of packing: 30kg

INSTRUCTIONS FOR USE

Foundation preparation

The substrate must be solid, clean, free of dust and dirt. Substances that weaken adhesion such as grease, dust, etc. must be removed.

Windows and other untreated surfaces must be carefully protected.

To increase the adhesion strength of the plaster mixture with the base, it is necessary to treat the surface with a primer. weber.prim contact. After applying the primer, it must be allowed to dry completely (drying time 24 hours). Avoid dusting the primed surface.

Preparation of plaster

Gradually pour a bag (30 kg) of dry mixture into a container with 13.5-16.5 liters of pure water, while stirring. The recommended water temperature is + 20°С.

Mixing should be done with a drill with a nozzle for 1-3 minutes until a homogeneous consistency is obtained.

In the process of applying the solution to the surface to be plastered, it is impossible to add water or a dry mixture!

It is not allowed to add other components to the solution.

Application

Spread the prepared plaster mortar on the surface within 40 minutes after mixing with a trowel with a layer of 5-50 mm, locally up to 100 mm. Then smooth the rule with zigzag movements.

When applying several layers, the second layer of plaster is applied without waiting for the first layer to dry completely (after 2-3 hours). Plaster ceilings only in one layer no more than 15 mm thick.

As soon as the plaster mortar begins to set (approximately 60 minutes after mixing), level the surface with a metal trapezoid rail or a wide spatula, cutting off the excess and filling in the recesses.

To obtain a smoother surface for decorative finishing (wallpapering, painting), the surface must be treated with finishing and superfinish putties: weber.vetonit KR, weber.vetonit LR+, weber.vetonit LR Pasta.

TOOL CLEANING

Use clean tools and containers for work (contaminated tools and containers reduce the time of using the plaster). Wash tools with water after use.

To achieve the best result, it is necessary to carefully plan the plastering work, taking into account the curing time of the gypsum plaster.

During the work, the temperature must be above +10°C.

The water temperature for mixing the dry mix should be between +5°C and +30°C.

PRECAUTIONARY MEASURES

When working, rubber gloves must be used; avoid contact with skin and eyes; in case of contact with eyes, rinse with plenty of water; keep away from children.

DISPOSAL INSTRUCTIONS

Dry mix and hardened material must be disposed of as construction waste. The material must not be released into the sewer. Dispose of the paper bag as normal trash.

Among the wide range of plasters on the market, Vetonit building mixtures are very popular. The product of this brand is of excellent quality and affordable price. In Russia, it is produced by the branch of the international construction group "Saint-Gobain" "Weber-Vetonit".

Types and scope

Firm "Weber-Vetonit" produces powder mixtures for a wide range of construction works.

The following types can be found on the market:

• "Vetonit Gypsum Plaster";
• Primer "Vetonit";
• "Vetonite Dispersion";
• Vetonit TT;
• Vetonit EP.

Insert your text here

Depending on the type of plaster, it can be used to:

• create a decorative layer inside or outside the room;
• level surfaces (walls or ceiling).

« Vetonit Gypsum plaster» is used for leveling indoor surfaces. It is a non-water resistant white plaster that can be applied by hand or machine. The end result is a surface ready for painting.

Primer "Vetonit"(or plaster mortar for leveling) is used for indoor work on concrete and brick surfaces.

« Vetonit EP» is a non-waterproof lime-cement based plaster mixture. It is most often used, like gypsum, in order to level large areas in one go. It is not recommended to be applied on weak lime and cement-lime substrates.

« Vetonit TT» is a waterproof cement-based stucco mix. Most often used for indoor work. This mixture is universal and can be used for plastering most substrates.

In the building materials market there are also decorative plasters of this company. It is recommended that you carefully read the instructions on the package before purchasing in order to obtain a high-quality end result.

Specifications

By comparing the characteristics of different types of plaster, it is easy to make an informed choice in favor of this brand or another.

Compound

Depending on the type of plaster, its composition differs.. So, the composition of "Vetonit EP" includes cement and lime. The main component of the most common Vetonit TT mixture is cement. The basis of "Vetonit T" is adhesive organic binders. "Vetonit L" is a plaster on a polymeric binder. So you must first study the composition of the mixture.

Colors

This product is intended mainly for subsequent painting, therefore, neutral colors are provided: white, gray and light gray.

Layer thickness

Vetonite can be applied in a layer of 2 - 10 mm, the maximum thickness is 3cm. Please note that it may vary depending on the type of mixture. More details can be found in the tables below.

Adhesion (stickiness)

The plaster has a high level of stickiness. The average adhesion strength is 0.5 MPa.

Frost resistance, moisture resistance

Dry powder is quite frost-resistant. He able to withstand 75-100 cycles of complete freezing and defrosting. Therefore, this product is recommended in cold climate regions.

Insert your text here

Strength

The strength of plasters of different types differs slightly. Thus, a gypsum-based mixture is less durable than a cement-based one. On average one month after plastering the surface can withstand a load of 6-8 MPa.

Having considered the technical characteristics, we can come to the conclusion that Vetonit is indeed an ideal material for interior and facade plastering.

More information about the most common types of mixtures can be found in the tables:

Having studied the technical characteristics, you can start plastering work.

Preparations for work

It should be taken into account that the solution should be applied at a temperature of +5 to +30 degrees. But if the package has an asterisk or there is the word "winter", which means that it can be used at low temperatures from -10 degrees.

It is necessary to take breaks between applying layers for up to two days and only after that proceed to the next stage. A week after the final work, the plaster acquires 50% strength.

Surface preparation

Surface preparation largely determines the final result.

The order of work is as follows:

• pre-clean the surface of dirt and level;
• cut protruding corners;
• all irregularities should be repaired.

You can strengthen the base with a reinforcing mesh.

When plastering concrete surfaces, it is desirable to treat it with a primer so that the concrete cannot absorb moisture from the mixture.

Solution preparation

For this you need:

• pour a package (25 kg) of dry solution into a container of 5-6 liters;
• knead the solution in water at room temperature;
• mix until a homogeneous consistency is obtained. You can use a powerful drill for this;
• Stir again after 10 minutes.

The plaster should be used within 3 hours.

Insert your text here

Working methods

Plastering can be done manually or mechanically.

When performing work manually, you must:

• apply the resulting solution to the previously treated surface;
• sand with a sponge;
• fill in the recesses;
• level the surface.

If you need to apply several layers, it is better to let the first layer dry for two days. and then move on to the next one.

The procedure for working with Vetonit is no different from the procedure for working with other types of plaster.

Advantages

This plaster is universal.

Among the advantages are the following:

• frost resistance and water resistance;
• non-shrink hardening and good level of adhesion;
• the possibility of plastering manually and mechanically;
• small expense;
• moisture resistance;
• application on different types of surfaces.

Products can be used on most known materials - concrete, aerated concrete, ceramic or silicate bricks, foam concrete, and so on, preparing the base for subsequent finishing with tiles, glass or plastic plates, as well as for applying putty.

disadvantages

There are not many disadvantages and they are insignificant.

The main ones are:

• the plastered surface dries slowly;
• crumbles when sanding.

Due to its numerous advantages and ease of use, Vetonit is in demand on the modern market of building materials.

By following the advice of professionals, you can avoid problematic situations.

Here are some of them:

• to increase adhesion (stickiness), you can use a special solution "Vetonit Dispersion";
• you can not use Vetonit as a base for tiles;
• tools and equipment must be cleaned immediately after each use.

Price

The price of Vetonit plaster is quite high. The price may vary depending on the type. The average price is from 400 rubles. for 25 kg. The goods are packed in packs of 5 or 25 kg. It is recommended to store in dry rooms in the original packaging. Shelf life is 1 year.

You can see more about Vetonit products in the video:

Gypsum plaster Weber.Vetonit Profi Gyps is used for basic leveling of walls and ceilings in dry rooms with normal humidity, as well as in kitchens, corridors, bathrooms (except bathrooms); for leveling walls with a layer up to 50 mm (locally up to 100 mm). It allows you to create a reliable basis for finishing due to the high strength of the composition. Plaster can be applied both manually and mechanically.

For use on the following substrates:

concrete, foam concrete;

• plastered surfaces;

  plaster surfaces.

Plaster gypsum Weber.Vetonit Profi Gyps contains microfiber, which guarantees high strength, gives super plasticity by improving the viscosity and consistency of the mortar, promotes uniform drying over the entire plastered surface and guarantees the absence of cracks. Superplastic plaster due to finely ground gypsum is easier to level and smooth. The quality of the final surface is smooth and uniform.

Plaster Weber.Vetonit Profi Gyps has increased adhesion to various substrates. It is easy to apply, does not slip, minimizes the possibility of delamination with a thick layer.

Features of gypsum plaster Weber.Vetonit Profi Gyps:

Reinforced with microfiber - up to 50 mm without cracks.

High quality finish surface.

Easy to spread and level.

Crack resistant.

It is superplastic in drawing manually and in the mechanized way.

Attention! Gypsum dry mixes can be of various white colors. It depends on the natural impurities in the gypsum stone. The color of the mixture does not affect its characteristics.

During the work, the temperature must be above +10°C. The water temperature for mixing the dry mix should be between +5°C and +30°C.