Interesting ideas to close the pipes behind the toilet. How to close the pipes in the toilet: how best to hide and hide the pipeline. Installation of duct frames and false walls

Hidden pipes in the toilet - a necessity or a tribute to the construction fashion?

An unambiguous answer cannot be given. On the one hand, the absence of open pipelines is a more aesthetic appearance of the room, increased sound insulation and, finally, a higher degree of hygiene. On the other hand, difficult access for taking readings from water meters or carrying out repairs.

Modern technologies help to formulate such an answer: "Hidden pipes are a necessary tribute to the building fashion."

There is a very common opinion that it does not make sense to “mask” the pipelines in the toilet until the pipes are completely replaced with plastic or metal-plastic. However, this is not quite true. Firstly, hidden pipelines will significantly improve the visual perception of the room.

Secondly, they will greatly facilitate the process of cleaning the toilet, especially capital. And thirdly, the use of components such as plastic, the role of shutters or blinds will allow you to quickly dismantle the shelter structure or simply provide unhindered access to the pipes.

Existing plumbing and sewer products made of plastic theoretically allow them to be buried forever in the thickness of the walls. But this option is suitable for linear sections of water-bearing communications.

Access to water metering units, shut-off valves and revisions is required. And preferably comfortable. The ergonomics of such access is equally dependent on both plumbers and installers hiding pipes.

The designs of systems for concealing pipelines in the toilet can be divided into four subgroups:

Frame. These include structures assembled on a metal frame, or wooden slats and timber. Further cladding is made with GKL, PVC panels or DSP boards.
Mounted. They are made-to-measure roller shutters or horizontal blinds fixed to the ceiling.
Combined. In this case, part of the protection is assembled on a frame, and part is a lifting system in the form of roller shutters or blinds.
Finished construction. This is usually a one-piece array, mounted as an assembly. A typical example is a metal-plastic frame with a window for access to the water meter assembly. Filling - sandwich panel.

Frame types of pipe shelters differ in the form of assembly and types of finishing.

Forms of installation of frame systems for "masking" pipelines

Solid barrier. It is a wall, assembled along the far or side walls of the toilet room. A distinctive feature of such a false panel from a conventional partition is the presence of a frame sheathing only from the visible part. An undoubted advantage of this design will be the possibility of the same type of finishing of the entire toilet - plastic panels, ceramic tiles, washable wallpaper, fiberboard panels, etc. The disadvantages are the impossibility of carrying out plumbing work behind a false wall and a rather significant decrease in the total area of \u200b\u200bthe toilet. Basically, the footage is compressed due to the unsuccessful location of pipelines, mainly sewer risers. As a result, you have to change the location of the toilet bowl - push it to the front door or move it to the side.
Corner partition. The principle of the device of an oblique false wall is the same as that of a solid partition. Only it does not close the wall, but the place where the walls of the room meet. Behind the corner structure it is convenient to place pipelines located in the corner. Ideal when the back of the frame touches the pipes farthest from the walls of the toilet room. However, if the sewer riser and plumbing are mounted at some distance from the corner of the toilet, then an oblique false wall can take up an unreasonably large area. In addition, uneven inner corners can significantly complicate the interior decoration of the toilet room. This can be especially true when lining walls with PVC panels.
Rectangular box. They are used to "mask" both vertical risers and horizontal sections of pipelines. The frame is mounted close to the existing pipes. Unlike false walls that completely cover a wall or corner, boxes cover only segments of the wall space. The horizontal sections sewn in this way can be used as shelves. Some difficulties can be caused by sewing hot water risers with heated towel rails. This is due to the features of the possible replacement of the heating device.
Multilevel boxes. This is a kind of symbiosis of walls, false panels and boxes. The boxes perform the function of "protection" of pipelines. They are mounted close to the pipes, and at the same time, as far as possible from the plane of the walls. The design in rectangular reflection repeats the relief of the indentation of pipelines from walls or false panels. Such stepped boxes save usable area as much as possible. An interesting option is to create multi-level structures with niches. The back side of the recess is the existing walls, the protruding plane is the outer part of the boxes. But such systems are relevant for toilet rooms of rather large dimensions. Frame facing material - plastic or drywall.

Hinged systems for concealing pipelines

Blinds. This "disguise" is more of a decorative character. But it will absolutely not interfere with the repair work. The installation location is often limited to the rear wall of the toilet room. With a lateral arrangement of pipes relative to the entrance, the installation of blinds simply does not make sense. Cross plates made of aluminum are preferable to plastic lamellas. Standard powder-coated colors allow you to visually connect the blinds with the materials of the toilet room wall decoration without transitions that cut your eyes.
Roller shutters. Roleta quite organically fit into the interior of the toilet room. Are made only under the order. There are no standard sizes. Separate roller shutters usually close the rear wall of the toilet. When mounting on the side, you can not do without boxes assembled from drywall. In this case, the issue of the device of the revision hatch is eliminated. If the size of the installed shutters corresponds to the dimensions of the linear projection of the pipelines, then no problems are expected during plumbing work.

Sound insulation of pipelines behind the boxes

This event is relevant only for multi-apartment high-rise buildings. The noise of the "waterfall", coming from behind decorative boxes and false panels in the toilet, rarely brings joyful feelings. Especially such discomfort is created by sewer risers.

Mineral wool will help solve this problem. Moreover, it is necessary to isolate not the plane of the partition, but the pipelines. Noise from pipes wrapped with glass wool becomes an order of magnitude lower.

Installation of duct frames and false walls

Metal carcass. It is made at the installation site from metal profile pipes by welding. The main frame is attached to the walls, floor and ceiling with anchors. The thickness of the metal is not more than 1.5 mm, which will make it possible to fasten the skin with ordinary self-tapping screws with a drill. Cladding material - DSP boards. Such a powerful design is designed to hang and hold heavy pieces of furniture or equipment on it. Typical examples are a cabinet for storing preservation for the winter or an electric water heater with a capacity of 100 liters or more. The complexity of the installation work and the cost of materials make such a frame a rather expensive structure.
Frame made of CD and UD profiles for drywall systems. The very name of the materials for the manufacture of the structure says that it is intended for gypsum boards. But, in addition to drywall sheets for sheathing, PVC panels can be used. For drywall, the usual installation scheme is used - a grid with a mesh size of 600 by 600 mm. But plastic will require horizontal fastening of CD-slats every 500 mm. GKL is fastened with self-tapping screws for metal, plastic - with a press washer. The biggest plus of this design is the speed and accuracy of installation.
Frame made of wooden beams and slats. The most economical version of the frame "camouflage". PVC panels, drywall, fiberboard, and OSB boards can serve as cladding material. But the cheapest is almost always not the best. A structure assembled from wood in rooms with high humidity is very susceptible to the risk of deformation. Therefore, further tiling cannot be carried out. And the rest of the materials on curved racks will lose all attractiveness.

Materials for sheathing systems for covering pipelines

Building components for frame cladding are divided into two categories:

Materials suitable for use immediately after installation work. These include:
- PVC panels. Lightweight and beautiful material that has proven itself when decorating rooms with high humidity. Seamless versions of plastic panels give the impression of solidity of the assembled planes. Plastic is very easy to work with. An extensive range of colors and a variety of textures of products can satisfy the most picky tastes. The disadvantage is excessive fragility.
- Chipboard boards. Such a furniture component gives a certain comfort to the toilet room. Especially if the finish of the box is made in the same style as the front door. In addition, laminated chipboards can be mounted as part of a wall cabinet with opening or sliding doors. It is quite appropriate to use mirrors. The downside is the high cost of the project.
- Wooden lining. Wood is always in fashion. But it is very difficult to harmoniously combine wooden parts with tiles or plastic. But to completely sheathe the toilet room with clapboard may not allow the area of \u200b\u200bthe room.
Sheet materials are the basis of future finishing.
- CSP boards. Reliable, but very heavy material, even if you use sheets with a thickness of 8 mm. Cut to size with an angle grinder. Absolutely not afraid of water. Particular difficulties may arise when constructing an inspection hatch.
- Plasterboard sheets. For sheathing the shelter frames, it is recommended to use moisture-resistant wall plasterboard with a thickness of 12.5 mm. Drywall has proven itself in the construction market. Very easy to process. Does not lose its properties under various finishing materials - primers, putties, decorative plasters and ceramic tiles. The main drawback loses its structure under the influence of water. Well, cases of flooding of bathrooms in multi-storey buildings are well known.

Finishing boxes

There are several options for finishing the finishing touches in the process of covering the pipes in the toilet. Here are the most common ones:

Ceramic tile. An old and yet modern way of finishing fragments of toilet rooms. A solid "experience of operation" of tiles is the best argument in favor of ceramics. The advantages are visible to the naked eye - ergonomics, durability, aesthetics, etc. etc. In the case of boxes, there is only one technical difficulty - the device of an inspection hatch, which looked organic and would be functionally convenient.
Textured plaster. The embossed surface of such a decorative coating may require more frequent and thorough maintenance of the raised panels. But there is a big plus - the plasterer is devoid of linear dimensions and quite easily hides minor installation errors.

Use as a screen to "mask" the remnants of cabinet furniture. Any used chipboard (wardrobe wall, countertop) will perform the same role as custom-made ones.
Temporary false walls can be fastened to ordinary mounting foam. The false panels do not bear special loads, therefore, the main thing is to fix them during the foam solidification.
The role of the inspection door can be successfully performed by a removable ventilation grille.

Numerous pipes, risers, bends, meters and valves - all this is located in a small bathroom, which is already not very beautiful. It is not surprising that when doing, many people think about how to hide pipes. As part of this article, we will understand and show a photo of how to properly hide pipes in a toilet or bathroom.

In standard apartments, as a rule, the bathroom is separate and the bulk of communications, such as the plumbing system, the water supply is also connected there and all this is located in the toilet, turning it into a kind of technical booth where the toilet was accidentally installed. In a private house, things are simpler and, nevertheless, there are a couple of pipes that catch your eye. There are many ways to decorate them, but before you hide the pipes in the toilet, you need to carry out a number of preparatory work.

Before starting work

When planning a bathroom and toilet renovation, be sure to consider a way to mask the water pipes.

First of all, you need to make sure that the communications are working properly. In no case should there be corrosive areas and, especially, leaks. Before hiding heating and water supply pipes, it is advisable to insulate them.
In advance, you need to determine the location of technological hatches and install main filters for water purification. Recently, roller shutters for the toilet have been especially popular. This option combines a neat appearance and full access to communications.
Be sure to pay attention to the condition of the walls. You need to make sure that there are no traces of mold or fungus on them. In the presence of the latter, a thorough mechanical cleaning and double treatment with fungicides are carried out.

Important! Plumbing hatches will provide free access to those areas of communications that need periodic maintenance, such as meters, filters.

How to choose a plumbing hatch: access to communications

A plumbing or inspection hatch installed in the walls allows you to maintain access to the main elements of communications. There are several options on the construction market:

Finished hatches. Usually, plastic, can also be made of metal or stainless steel. Do not need additional finishing.
Inspection hatches are installed if the question is how to hide all the pipes in the toilet or in the bathroom under the tiles. They belong to the category of invisible hatches. The sanitary door is decorated with the same finishing materials that are used for the walls, making it almost invisible.
The frame of such hatches is steel, and the doors are made of gypsum fiber. They are used for openings of different sizes, so that the piping in the toilet becomes as accessible as possible.

Inspection hatches: plastic (left) and decorated with tiles (right)

Paintable sanitary hatches are an aluminum frame and a drywall door that can be painted in any chosen color. The design does not imply finishing with other materials.

Pipe box: configuration, installation

A decorative box for covering pipes is suitable in most cases. Depending on the placement of communications, it can be made in several versions.

False wall. An easy and quick way to hide the pipes is if they are located along one of the walls, usually behind the toilet. Of course, the wall will take at least 50 cm, the already small length of the toilet. But this problem can be solved by installing a hanging toilet, which is mounted on a special module hidden behind the wall.
The drain tank will also be located behind the wall inside the pipe box. In this case, in order to provide access to important communication elements or to change the coarse water filter, several simple plumbing hatches are installed.
Beveled false wall. This option is resorted to when thinner branches go in different directions from the nodal riser. The wall in this case is located at an acute angle to the side and back walls. This option looks interesting, but it will take a lot of usable space.

Beveled false wall (left) and flat false wall (right)

Multilevel boxes. In some toilets, if you protect all communications with a wall, there simply will not be room for a toilet bowl. In this case, resort to a multi-level box. Each individual structural element masks a certain section of the pipe. Multi-level designs look very interesting and allow you to functionally use the end part of the pipe box.
A square box is mounted when the piping in the toilet is simple, all pipes and a coarse water filter are located in one corner. It takes up little space.

The choice of material for finishing the box

Usually, the same material is used for lining the boxes as for the walls. And the most popular, of course, is. And not only for aesthetic reasons, it is easy to clean, resistant to disinfectants and durable.

Finishing the box with plastic (left) and tiles (right)

In addition to ceramics, plastic panels are laid. They are cheaper and less reliable, but if pipe repairs are required, such a box is easier to dismantle. Sometimes the construction of a box made of drywall is only painted, but the option is not practical and durable. In addition, dirt accumulates in the pores of the paint, and this contributes to the development of bacteria.
Facing stone, brick or mosaic are more often used only fragmentarily, to highlight certain areas. Thus, for example, it is possible to allocate a plumbing hatch for ceramic tiles.

Box installation

At the initial stage, it is necessary to decide on the choice of material for finishing the box. If it is ceramic tiles or, the frame is made of a metal profile and sheathed with drywall. For plastic or wood panels with a waterproof coating, the frame can be made from wooden blocks that do not need additional sheathing.
The installation of the box is carried out in several stages. Preparatory work includes measurements and marking the location of the structure, taking into account the thickness of the material. The structure of the box must be at least 3 cm from the pipes.
The next step is fixing the frame elements. When a profile is fixed around the perimeter of the future structure, guide elements lead from it and form an angle. Sheets of drywall are cut in such a way that the box for covering pipes, if possible, consists of separate strips.

Drywall is attached to the profile with self-tapping screws. If further finishing involves painting or wallpapering, the structure is primed, puttied and sanded with sandpaper.
In no case should you close the so-called revision areas, they are used to clean sewer pipes. They also provide access to the meter, taps and open the coarse filter of tap water.

Roller shutters in the toilet

Plumbing modern roller shutters in the toilet are installed if all pipes are located along the back wall. They represent a canvas of lamellas, which moves along vertical guides, and is wound on top of a shaft protected by a box.

Roller shutters for masking pipes in the toilet and bathroom

The main advantage of roller shutters is that they are able to provide free access to pipes. More often, roller shutters in the bathroom are attached directly to the wall and ceiling. Installation is carried out both at the initial stage of repair work, and after their completion.
Before proceeding with the installation of blinds, it is necessary to measure the diagonals of the openings. The difference between the two measurements should not exceed 5 mm. And make sure that the vertical and horizontal slopes correspond to the level. The most practical for the toilet will be a built-in installation, a box in or out.

Important! It is better to install roller shutters before laying tiles. Thus, it will be possible to hide the gaps between the wall and the guides.

Installation of roller shutters

Markings are made on the guide rails. 10-15 cm recede from each edge of the tire, on the rest of the segment the marks are distributed evenly, in increments of 45-50 cm. Holes with a diameter of 11.8 mm are drilled in the inner wall of the tire to attach the box to the opening.
On the edge of the front flanging of the box and its cover, joint holes with a diameter of 4.2 mm are drilled, two on each side. In the future, they will be used to fix the box cover with rivets. Further, a hole with a diameter of 8 mm is distinguished and drilled in the upper flanging of the box panel for fixing it in the opening.

Scheme of installation of roller shutters for a sanitary cabinet

Assemble the roller shutter frame (box and guides) and install it in the opening strictly according to the level. The iron sheet is led over the drive shaft from the side of the rear wall of the box into the guide rails. At the edge of the canvas, traction springs are fixed and fixed to the shaft. Fix the box cover. Close the holes with plugs. Check system operation.

Advice! Roller shutters to the toilet are usually plain, and this does not affect their aesthetic qualities in the best way. You can make them more attractive and match the finish with the help of airbrushing.

The interior of a modern toilet room should carry not only an aesthetic component, but also be as comfortable as possible.

An important role is played by the method of laying sewer pipes. Few people like open pipes in the toilet. In addition to their appearance, cleaning them can be quite a hassle.

To prevent this, concealed mounting is the best solution.

Depending on the required throughput and technical standards, pipes of the following types and sizes can be installed in the toilet room:

plastic from polypropylene. The recommended diameter for connecting a toilet bowl is 110 mm. In this case, the pipe must be directly connected to the riser.

For other plumbing fixtures (sink, bathtub, etc.), the diameter of the supply pipes must not exceed the diameter of the appliance outlet. Traditionally, this is a size of 50 mm.

cast iron pipes. Currently, they are practically not used due to poor performance, high price and complexity of installation.

When replacing cast-iron pipes with plastic ones, it should be borne in mind that the wall thickness of cast-iron pipes is much greater than plastic ones.

Photo: piping in the toilet, which must be hidden

Selection should be carried out according to the internal dimensions of the pipe.
Upon completion of the selection of material, work is underway to install the sewer line.

Installation methods

Currently, there are 2 types of installation of sewer pipes:

open. The entire pipe area is in the free access zone;
closed. Pipes are hidden using special structures or by strobing.

Using the first method allows you to save space in the toilet, since additional structures will not be present in it.

In the second method, the pipes are not visible, which allows you to give the toilet a more aesthetic appearance.

closed installation

With closed installation of pipes, it is necessary to adhere to certain rules, non-compliance with which can lead to unpleasant consequences.

Important! A feature of the hidden installation of sewer pipes is the ability to check their condition and carry out cleaning and repair work.

Before deciding how to hide pipes, you need to familiarize yourself with the installation rules.

Flush mounting rules

in the process of designing a structure, it is necessary to take into account the location of water and sewer meters. You can provide free access to these devices using inspection hatches or a freely removable panel;
before starting work, all pipes must be installed in accordance with the standards: have a certain, connecting joints are checked for tightness;
when it is necessary to provide access to their design for periodic cleaning and checking the condition;
during installation, pipes that tear off structural elements should not be subjected to mechanical stress.

Compliance with these rules will prevent unforeseen problems in the operation of the sewer system.

How to close pipes in a box

Closing pipes with additional structures is the most common way. In this case, you can choose from several options for shapes and design solutions.

The material for the manufacture of the structure can be varied: drywall, plastic panels.

false wall

With a relatively large area of \u200b\u200bthe toilet, the most optimal way would be to make a false wall.

It is a solid structure, the dimensions of which are close to the dimensions of the wall.

Photo false wall:

Being at a certain distance necessary to hide the sewer pipes, its installation is done right next to the ceiling and floor.

Depending on the external cladding materials used (plastic, drywall, tiles), the technology and method of mounting the supporting structure is used.

Photo: false wall installation

The advantage of this concealment of sewer pipes is the variability of forms.

Video: Repair of a typical toilet in a multi-storey building

For optimal distribution of free space, the following types of false walls can be used:

oblique;
box;
multilevel box.

Oblique false wall

With small dimensions of the toilet room, you can use the method of spot hiding pipes. In particular - the construction of the riser.

To do this, all pipes adjacent to the wall are closed not with rectangular boxes or a solid wall, but with a structure located at an acute angle to the load-bearing walls.

Photo: oblique false wall oblique false wall with a hatch

When designing this structure, the following recommendations should be followed:

after installation, the panels should not come into contact with pipes. This is necessary to prevent the ingress of moisture that occurs on the surface of the pipes;
the size of the front side of the false wall must be calculated so that inspection hatches can be installed. Ideally, this is a composite wall with removable panels.

square box

The square design of the decorative wall is the most common and can be of the following types:

floor-to-ceiling box. Hides the riser pipe;
a rectangular structure having an upper horizontal surface at an arbitrary level (multi-level type).

Photo: square box complex box design

The requirements for installation rules for this design are the same as for oblique false walls. This method is optimal when deciding how to close the pipe in the toilet.

Tiered box

To maximize the useful use of false panels, a combined pipe closing method is often used when square and multi-level boxes are mounted.

Photo: three-level box

This technique will allow you to hide all sewer pipes, while maintaining the free space of the toilet.

The horizontal surfaces of short boxes can be used as shelves.

Gating

Chamfering is the process of making mounting recesses for pipes in a wall.

The use of this installation method allows not to reduce the size of the toilet due to additional structures.

Photo: strobe under pipes

This method has strict limitations on the technical parameters of walls and pipes:

maximum pipe diameter 50 mm;
when gating a load-bearing wall, the depth of the furrow should not exceed 15% of the wall thickness;
due to the specifics of the technology, it is impossible to hide the riser and pipe from the toilet in this way;
it is mandatory to provide for the installation of inspection hatches throughout the entire pipeline.

Open mounting

In modern bathrooms it is almost impossible to meet the traditional open installation of sewer pipes.

Photo: open pipe installation

Its technology is simple and consists only in observing the laying standards - sewer pipes, choosing the correct pipe diameter and manufacturing materials.

Often, when planning open installation, they try to combine sewer and water pipes in one bundle. At the same time, the minimum distances between them must be observed.

How to close the pipes

The most important issue when hiding sewer pipes is the choice of material for the manufacture of false walls.

To do this, it is necessary to take into account the specifics of the toilet room - high humidity and a small area of \u200b\u200bthe room. Consider the most popular ways to hide pipes.

Closed with plastic panels

Photo: plastic panel box

Plastic panels are measured sheets made of PVC. Their main characteristics are:

thickness - 5 to 10 mm. The larger it is, the stronger the panel;
dimensions - length (260 cm, 270 cm, 300 cm and 600 cm) and width ( from 10 cm to 50 cm). The size is chosen taking into account the minimum residues after installation;
method of attaching panels to each other- suture and seamless.

Before starting work, you need to take care of the availability of materials and tools.

Materials and tools

The optimal set of tools includes:

building level and tape measure;
a drywall knife or a special saw for plastic. Necessary for cutting panels;
metal scissors;
screwdrivers - slotted and cross;
drill;
screwdriver Facilitates the installation of panels.

List of required materials:

plastic panels;
steel mounting profile - UD and CD;
floor and ceiling plastic plinths, corners - internal and external.
start line;
mounting dowels for fastening a steel profile;
metal fasteners - suspensions. Required to install the mounting profile from the wall plane to the required distance;
transparent silicone;
press washers with a drill 3.9 x 16.

Before purchasing materials, it is necessary to calculate the area of the future false wall and choose the optimal size of the panels and the mounting profile, taking into account the minimization of residues after cutting.

Installation process

Calculate the required distance from the wall to the installation of the trim panels.

Photo: installation calculation

Install hangers on the wall, taking into account the location of the inspection hatches. They should be at a distance of at least 300, but not more than 600 mm from each other.

Installation is carried out using a drill and dowels.

After installing the suspensions, we proceed to fastening the steel profiles. Bend the mounting ends of the hangers perpendicular to the plane of the wall.

Photo: installation diagram of a box of metal profiles

Using the level, start fastening the profiles so that their common plane is the same over the entire area. It must also be strictly perpendicular to the plane of the floor.

After installation, you should get the following picture.

Photo: profile frame

Install inspection hatches in previously prepared places.

Installation of panels starts from the door, they are installed vertically.

Photo: mounting panels on a profile

Using a drill, they are screwed to the mounting profile with press washers through special shelves on their structure.

To hide the edges and corners, additional profiles are used - the starting strip, skirting boards and corner profiles.

At the end of the installation, the joints located near sources of moisture can be treated with silicone.

Close pipes with roller shutters

Photo: masking pipes with roller shutters

Installing a roller shutter in a toilet as a building envelope is more practical than installing inspection hatches. They allow free access to the interior space between the wall and the bezel.

Materials and tools;

drill;
level and tape measure;
fixing material;
installation kit for roller shutters;

Mounting process

Depending on the size of the roller shutters, they can be mounted on the entire wall area or in separate blocks.

To install the roller shutter over the entire area, the following preparatory work should be carried out:

align the walls so that the distance between them is the same over the entire height;
installation can be done both before the final cladding of the remaining walls, and after;

Installation of a small roller shutter is carried out in a structure made of steel profiles, similar to the fastening of plastic panels.

Important! The distance between the profiles must correspond to the required opening for the installation of the roller shutter.

Guides and the upper box are installed according to the instructions.

Photo: installing guides

Lamellas are attached to the drum shaft. They must be in the grooves of the guide rails.

Photo: lamella fastening

After installing the last lamella, the structure is checked for opening and closing. The result should be a design, as in the figure.

Photo: health check

However, it is worth noting that the installation of roller shutters requires qualifications and experience. It is best to involve specialists for this.

Roller shutter installation video

We close with drywall

Drywall, as a material for making a false wall in a toilet, is considered as the basis for cladding (moisture-resistant wallpaper, tiles, painting).

Materials and tools

To carry out the work you will need:

roulette and level;
drill and screwdriver;
fixing canopies;
drywall sheets.

For work in a room with high humidity, it is necessary to use moisture-resistant drywall. Standard sheet dimensions are: width - 1.2 m; height - 2, 2.5 and 3 m. Thickness 12.5 mm.

mounting dowels and press washers for fixing drywall;
finishing putty and paper tape for insulating joints.

Mounting process

Fastening the frame for mounting drywall panels is completely similar to the frame of plastic panels.

Photo: installation of profiles

Marking is made for the installation of a steel profile, canopies are attached to which the profile is installed.

Before installation, it is not necessary to install inspection hatches - upon completion of all work, holes are made in the plasterboard wall equal to the dimensions of the hatches and placed in these openings.

Photo: plasterboard sheathing

The surface is treated with finishing putty.

Hiding pipes under tiles

The traditional use of ceramic tiles for wall cladding in the toilet is also possible in the manufacture of a false wall.

Photo: box under the tiles

Materials and tools

For work you will need:

roulette and level;
drill and screwdriver;
slotted and cross screwdrivers;
steel profile for the manufacture of the frame;
fixing canopies;
drywall or other moisture-resistant material that will become the basis for the tiles;
tile;
tile adhesive;
tile cutter.

Mounting process

Installation of tiles can be carried out both on a false wall, and in the case of using gated concealment of sewer pipes.

A layer of glue is applied to the surface prepared for installation. The mounting part of the tile is moistened for better adhesion to the adhesive.

Photo: box frame

Installation of tiles is done from the corner.

After the final installation, inspection hatches are installed in pre-prepared holes.

Photo: cut holes for hatches

In order not to spoil the aesthetic appearance, you can use special designs of hatches on which tiles can be glued.

Photo: glue tiles

Video; hiding pipes in the toilet under the tiles

Hiding horizontal pipes

Hiding is possible in several ways:

installation of a structure from profiles with subsequent cladding;
purchase of special decorative boxes for hiding pipes.

The choice depends on the specific configuration of the pipeline and the area of \u200b\u200bthe room.

If the decorative box matches the general style of the toilet, then such an installation will be optimal. It won't take much time or money.

When solving the problem of hiding sewer pipes in the toilet, one should adhere to the "golden mean". The design should be in harmony with the functional component.

Video: Installation of an invisibility hatch in a box

When renovating hygiene and toilet rooms, many prefer to close pipes that spoil the view. This is how you can add aesthetics, beauty and attractiveness to the room. It is worth noting that sometimes it is much easier to finish the walls and floor than to sew up the back wall with pipes. There are many ways to mask the bathroom and toilet from pipes, and each has its own characteristics and disadvantages.

The most popular way to hide a sewer pipe is to sew it up with plastic panels. The only drawback is that the masking with plastic panels stands out significantly from other walls, but you can fix the drawback if you completely finish the bath with plastic.

This option has a number of advantages:

Ease of installation;
Safety for human health;
It is possible to get close to the pipes in case of an accident or simply to inspect the integrity and suitability for operation;
Long service life;
Ability to quickly dismantle if necessary.

The disadvantage of the box also lies in the fact that the design is too voluminous and in an emergency it is not too easy to get to the pipes. The principle by which a box is installed for closing sewer pipes is the same, and you should not be afraid of such upcoming work and contact a specialist for large sums of money. Spending will be completely thoughtless, since it is possible to do everything with your own hands.

What material is better to use to sheathe pipes on the back wall with your own hands? There are many options, however, the choice must be made by choosing according to the design decision, the area of \u200b\u200bspace for which sheathing is required and the budget.

Before you close up the niche and hide the pipes, you need to take a number of important actions that are essential to prevent serious consequences:

It is necessary to replace the pipes with new ones;
Defects need to be fixed;
Be sure to check all tees, couplings and taps for leaks.

If you want to decorate a niche and save a lot, you should give preference to products such as blinds or a plastic curtain, however, the cheapest option is a drywall box. It is advisable to choose plastic pipes. They have a long service life, and practice shows that there are practically no problems with them, such as leaks and breakthroughs.

The principle of assembling a box for pipes in a toilet

How beautiful to hide the pipes in the bathroom? It is necessary to choose not only the material, but also to decide how the stitching will be carried out. It is important to note that not even an experienced craftsman can make such a plumbing decor, and for the construction it will be necessary to prepare a metal profile, a wooden beam and material to close the communication.

When closing pipes with a box, you can use canvases such as:

Waterproof plywood;
Sheet of waterproof GKL;
Plastic panel.

If we cover it with a sheet of drywall, then it is required to decorate it, and you can decorate it with tiles. In order not to violate the integrity of the interior and design ideas, it is best to choose exactly the GKL sheet and tiles. This is how the room will be completely in one form and there will be no places that stand out against the background of the rest of the room.

If sealing requires too much effort and time, which simply do not exist, then you can always order the manufacture of such a box or purchase a ready-made one. At a cost, these methods are much more expensive, but can be better. You can block the pipes with a box, with a different configuration. False wall. This option of the box is suitable if the room is decorated with too small dimensions. When installing a false wall, many people prefer to change the usual stationary toilet to a hanging-type equipment with installation.

A square-type box is perfect for decorating pipes located in one part of the room. Be sure to make a window for tracking data on the counters. An oblique false wall lies in the fact that it is installed at an acute angle relative to the back or side walls. Using this option, it is possible to close thinner pipes extending from the main part of the riser.

It would be inappropriate to install a large box here, since it is easier to make a small bevel.

The multi-level box is suitable for those rooms in which pipes have to be fenced off into the space of the room. In other words, when they are sewn up, a kind of small wall is constructed, which can divide the area of \u200b\u200bthe toilet and bath, if they are combined. In general, the process of creating a box consists in the installation of a metal profile, the installation of reinforcements from a bar, as well as the build-up of sheathing material.

Before carrying out all the above works, you need to create a project, make markings on the wall, and only then install the guide profiles. To install the profile, use fasteners in the form of dowel-nails, mounted using a perforator.

Do I need a box in a drywall toilet with shelves

Finishing PVC pipes or just ordinary cast iron pipes in the toilet is carried out in order to hide them from prying eyes, significantly improve the aesthetics of the room and get another flat surface that can be decorated with shelves or any other accessories. The easiest way to sew up pipes in a toilet or bathroom is to install a drywall box.

This method has a number of advantages that cannot be ignored:

Installing the canvas is not difficult;
If necessary, it can be easily dismantled;
For the construction of the structure, you do not need to use super skill skills;
The material is completely safe for human health, even with strong heating;
The canvas does not emit toxic substances;
It is the GKL canvas that is great for subsequent decoration with plastic panels, tiles and other materials.

It is worth paying attention to the fact that drywall has a drawback and this is that if you need to remove the box to repair or replace pipes, then it must be completely dismantled. Drywall itself has a number of advantages, which only increases the demand for it when installing the box in the toilet - a long service life, optimal cost, availability.

It is easy to cut and for this you need to use a regular or clerical knife.

If the material is impregnated with an additional soil composition, then its properties will be improved. The canvas has a soundproof property. If you purchase a moisture-resistant coating, then you can not worry about the formation of problems such as mold, fungus and similar consequences. As for the shelves, whether to install them or not depends only on personal preferences, since if the room is too narrow, then additional shelves can help remove excess furniture from the room, for example, a wardrobe on which the door takes up a lot of space when opened, and thereby release the quadrature.

Blinds and a box in the toilet or how to fix pipes

As already noted, there are various ways to sew up pipes in a toilet, and blinds are one of the newest. Thus, it is possible to emphasize the presence of aesthetic taste among the owners of the house and at the same time make the toilet more beautiful and stylish. Blinds are a great option for a small room, and also one of the cheapest.

Blinds can:

Save square footage;
Quickly disguise the back wall;
Inspect pipes, if necessary;
Install shelves in a niche and have constant access to them.

Blinds have their drawback, and it lies in the minimum period of preservation of the proper form. As a rule, they quickly turn yellow and darken. It is better to choose blinds in which you can easily replace their chassis or, in other words, the curtain. If you purchase a ready-made box, then there will be no problems, and you only need to install the structure in its rightful place. However, not every feature of the toilet allows you to install such products, and therefore you need to first familiarize yourself with the configuration of the room and all the possibilities.

Methods: how to close the pipes in the toilet (video)

If you correctly form the project, take into account the nuances in it, and at the same time select only high-quality materials, then you can make a simple and stylish finish for the toilet, through which sewer pipes will be hidden.

In the toilet rooms of well-maintained houses and apartments, sewer risers and various water supply pipes equipped with various taps and meters are installed. Most often, undisguised communications are laid along the walls, which spoil the look of the toilet room. You cannot remove them, but you can close or hide them.

To solve this problem with your own hands and without unnecessary hassle, there are many ways that will help not only hide the pipes, but also make the interior of the toilet more harmonious.

Choice of material for closing pipes

The modern construction market offers a large selection of finishing materials. However, not all of them can be used to hide pipes in the toilet.

You should choose materials that will not corrode and change their shape at high humidity and temperature. In addition, with their help it should be possible to build a compact and lightweight structure.

Finishing materials with similar characteristics include:

drywall;
moisture resistant grades of plywood;
plastic panels;
simple and ennobled MDF;
roller shutters;
tile.

In order to determine how much material is needed to close the pipes, it is recommended draw a toilet plan on a scale, put on it the location of communications and draw various options for the location of the box. Thus, it will be possible to understand which of them will look more organic and save more space in the room.

In addition, do not forget that when building a box with your own hands, which will hide the pipes, you should leave an opening for free access to pipes. Its dimensions should be such that plumbing work can be carried out freely.

It should also be borne in mind that the box with which communications will be closed must be made so that in the event of an accident or if pipes need to be replaced, it can be easily disassembled.

How to close pipes with a drywall box

A false wall made of drywall or drywall is the easiest and cheapest option for hiding pipes in a toilet. GKL should be waterproof, with the greatest thickness of the sheet.

For the construction of a drywall box, first of all, it will be necessary build a frame consisting of guides and rack profiles. A tight connection will need to be ensured between the concrete or brick base and the frame.

Materials that will be needed for the manufacture of the structure:

Metallic profile.
Drywall.
Self-tapping screws for metal.
Dowel for fastening the profile.
Putty.
Finishing materials (ceramic tiles, wallpaper or paint).

Required tools:

Perforator or drill.
Level.
Roulette.
Screwdriver.
Sandpaper.
Putty knife.
Drywall knife.

Do-it-yourself work on the construction of the box is recommended to start from the floor. With the help of a tape measure measure a piece of profile, cut off its length and evenly attach to the floor. In the floor, through the profile, make holes with a drill into which to hammer the dowels.

Before attaching the profile to the side walls, its location must be determine by level. To do this, the profile is placed along the edge of the piece attached at the bottom and aligned. A line is marked with a pencil along which the profile will need to be fixed.

If the box is solid, then between the side sections of the profile it will be necessary to install longitudinal ones, to which drywall will subsequently be attached.

After all profiles are installed, to them sheets are attached. To do this, the necessary piece is measured, which is cut off with a knife and fastened with self-tapping screws. The step between the fasteners must be at least 20 centimeters.

Seams between sheets of drywall sealed with putty and reinforcing mesh, which prevents the appearance of cracks at the seams. The opening left for free access to the pipes can be closed with a pre-purchased special hatch with a magnetic lock.

After completing the installation of the box, you can proceed to its lining. An inexpensive and quick finishing option is box painting in the color of the walls of the toilet with water-based or oil paint. First you should not forget to putty the finished structure. However, it should be borne in mind that from time to time it will be necessary to make cosmetic repairs by updating the paint.

The most durable option for finishing a false wall is the use of ceramic tiles. This is quite expensive, but at the same time the most common way.

Facing the box with ceramic tiles

For laying tiles you will need:

Primarily adhesive is being prepared with which the tile will be attached to the structure. To do this, the dry mixture is added in small portions to the water and stirred with a mixer. The resulting solution should be of medium consistency, that is, not too thick and not too liquid.

Laying tiles starts from the floor. At first the rail is laid and leveled, and then a tile is glued on it.

To attach a tile to its inner surface with a spatula, you need to apply adhesive mixture and distribute it evenly. Then the tile leans and presses a little against the wall.

Between tiles insert plastic crosses, leaving a gap of 2-4 mm thick. Subsequently, it will need to be rubbed with a special mixture for tile joints.

How to close pipes with plastic panels

Installing plastic panels is an easy and cheap way to close communications in the toilet. Plastic is flexible and lightweight, easy to use and affordable.

Panels are attached to the frame, which is constructed from metal profiles or wooden slats. Using self-tapping screws, a starting F-bar is installed on the frame, into which pieces of the panel cut off to the required size are inserted.

Each subsequent panel with the one already installed must be connected using the lock on the edge of the strip. Long panels in the middle part desirable additionally fasten with self-tapping screws.

To hide the corners and edges of the sheets, it is recommended to use additional corner profiles, skirting boards or starting line. The joints of the panels, which are close to sources of moisture, can additionally be treated with silicone.

How to close the pipes in the toilet with roller shutters

Installing roller shutters is more practical, as they provide free access to pipes. You can mount them in separate blocks or on the entire wall.

However, the installation of roller shutters is quite complicated.

Necessary tools and materials:

installation kit for roller shutters;
fixing material;
roulette;
level;
drill.

Before starting work on the installation of roller shutters, the walls in the toilet must be leveled so that the distance between them is the same.

Roller blinds are installed in the structure from steel profiles, the distance between which should be equal to the width of the roller shutters.

When installing roller shutters in the first place guides are installed. Then the upper box is attached, to the drum shaft of which lamellas are attached.

Having installed the last lamella, the design must be check for closing and opening. In this case, it should be noted that the lamellas should be in the grooves of the guide bars.

Since for the installation of roller shutters experience required it is best to seek the help of a specialist.

When solving the problem of closing pipes in the toilet, it is necessary to take into account the fact that the functional component must be in harmony with the design of the room. The design can not be mounted independently, but bought and installed special decorative boxes designed to hide pipes. The choice depends on the area of \u200b\u200bthe room and how the pipeline is laid in the toilet room.

Categories

Popular