Clinker brick for wall decoration. Clinker brick for interior decoration. English style - a combination of aristocracy, sophistication and restraint

When choosing a material for finishing an apartment or a country house, you should pay attention to decorative tiles imitating stone or brick. It can be used for uniform wall cladding or combined with wallpaper. Despite its apparent simplicity, brick-like tiles for interior decoration have a number of installation features that must be taken into account when planning work with it.

Bare brick walls give the room a gloomy and uninhabited look. However, today many choose just such a design, because it is concise, non-standard and makes it easy to select accessories.

To create the effect of bare walls, you can use:

wallpaper with a pattern of bricks;
special panels;
imitation of brickwork on wet plaster;
brick tiles;

Consider the advantages and disadvantages of each of the finishing material separately.

The most inexpensive and easiest material to install is wallpaper. To create with their help the effect of bare brick walls, it will take a minimum amount of time. These wallpapers are perfect for any style decision of the room.

If we talk about the advantages of this material, they are obvious:

their gluing does not require special experience in construction work;
when finishing, a minimum amount of debris and dirt remains;
calculation of the required amount of material can be done directly in the store;

the period of finishing work is extremely short;
there is no need to use special tools;
a large selection allows you to choose the best option at an affordable price.

Note! Textured non-woven wallpaper allows you to get the effect of real brickwork. However, a significant disadvantage of this material is the ability to accumulate dust and low water resistance.

On the Internet there are a large number of photos of brick wallpaper in combination with other materials.

Decorative wall panels

Brick-like panels for interior wall decoration are wear-resistant and highly resistant to moisture. They are actively used for exterior and interior finishing work.

Among the advantages are:

durability;
light weight;
long-lasting excellent appearance;
high soundproofing characteristics.

For the manufacture of panels, plastic is used, which is easily attached to the wall with screws or self-tapping screws. Due to the fact that each panel is mounted separately, in case of damage, it is easy to replace a single fragment.

Brick tiles for interior decoration

Indoors, facing brick tiles began to be used relatively recently. Prior to that, it was a material for outdoor finishing work. At first, the cost of the tile was quite high, and it did not feature a wide variety of design options. Gradually, the color range was expanded and various texture solutions were proposed.

Among the advantages of brick tiles, it is worth highlighting:

environmental cleanliness;
the ability to use with various materials (wood, plywood, metal, concrete, etc.);
durability;
good sound insulation;
high resistance to moisture.

Despite the large number of advantages, one should not forget about a number of significant disadvantages. Among them is the need to involve specialists in the work and the mandatory use of special materials. Not the last negative point of laying tiles is dirt, the need for preparatory work and a large amount of construction debris.

However, the design solutions obtained through its use will please the eyes of the owners for a long time and give the room an individuality.

Types and materials for making tiles

The building material used for interior finishing works is not exposed to intense sunlight, temperature extremes, high humidity, etc. However, this does not mean that it is worth inattentively and frivolously approaching his choice. This is due not only to the quality of the tile, but also to the features of its laying, which differ significantly from the laying of ordinary tiles.

Before dwelling on a specific type, it is necessary to answer the question of what is planned to be obtained as a result: a complete imitation or a fairly distant similarity? The answer to this question will allow you to choose the right one, which is produced in the form of one brick or several rows.

The latter option is easier to install, because it is large in size, and docking takes place according to the chess principle. In this case, the brick wall will differ from the usual texture, but this will allow you to get an unusual effect and give the room a unique look.

Note! When choosing the type of tile in the form of panels, it is necessary to remember the increased fragility in places where the seams are simulated.

It is worth noting that the choice of material from which it is made also has a significant impact on the strength of decorative tiles for bricks. For these purposes, clinker, ceramics, polymer cement or gypsum can be used. Each of the materials has its own characteristics, which must be taken into account when choosing tiles for finishing various rooms.

Types of decorative brick tiles for interior decoration

Each apartment owner independently decides on the choice of one or another type of tile for wall decoration. In this case, it is necessary to take into account many points, among which are operational characteristics (bathroom or living room). In addition, do not forget about the advantages and disadvantages of each material from which the tile is made.

Clinker bricks for interior decoration

This type of tile was originally used for outdoor finishing work, but recently it has been actively used indoors. This is due to the large number of advantages of this material:

simplicity and ease of laying on a surface of any complexity;
resistance to ultraviolet radiation, bacteria and friction;
long service life due to high surface strength;
water absorption;
ease of cleaning from dust and dirt.

Despite the advantages, clinker tiles for interior decoration also have disadvantages:

low impact resistance;
high cost, which is especially taken into account when choosing between clinker and conventional ceramic products.

Advantages and disadvantages of using gypsum tiles to imitate bricks. Styling methods. Features of working with different bases.

Brick-like ceramic tiles

For the manufacture of this type of tile, sand and clay taken in certain proportions are used, which results in an environmentally friendly finishing material that is great for both outdoor and indoor work. This type differs from other types of brick-like wall tiles with a smooth texture, which makes the masonry with its use as similar to the real one as possible.

This type of material is great for all types of rooms, and also combines well with wood, wallpaper, etc.

Polycement tiles

A crushed mixture of sand, cement and shells is used to make this type of brick tile. Among the advantages of this type, it is worth noting light weight, high breathability and a beautiful textured surface. However, this tile has a significant drawback - increased fragility. Therefore, its transportation and installation is carried out with great care or with the help of professionals.

It is used for finishing living rooms, bedrooms and a corridor, but in the bathroom it should not be used, as the tile will quickly deteriorate and the repair will have to be done again.

Flexible tile for interior decoration

For the manufacture of this type of tile, a mixture of cement, acrylic polymer and pigments is used. A distinctive feature of this material is the ability to bend at any angle. Therefore, it is excellent for finishing various rounded surfaces. To bend the tiles, a regular or building hair dryer is enough.

Among the advantages of flexible brick tiles, it should be noted:

high heat and sound insulation;
ease of installation and no special requirements for work;
light weight;
the minimum amount of waste after installation;
cladding does not require the use of a special agent, ordinary cement is sufficient;
high resistance to temperature extremes and high humidity;
the surface of the material is pleasant to the touch.

Among the shortcomings, it is worth noting the high price of brick tiles for interior decoration.

Advantages of decorative bricks for interior decoration

Any type of tile allows you to create the illusion of brickwork, but it has several advantages over its progenitor:

ease of cladding. This makes it possible to significantly save on repairs;
brick wall decoration does not require preliminary surface preparation. The exception is gypsum walls, which require additional mesh reinforcement;
thanks to a wide price range, everyone can buy brick tiles;
it is possible to choose this finishing material for any design solution due to the wide color range and surface texture. At the request of the client, manufacturers can make tiles with his last name or family coat of arms;

material is excellent for finishing door and window openings. The result obtained looks unusual and stylish;
the ability to use with any modern style - Italian, art deck, loft, Provence, rustic, etc.

Helpful advice! The use of tiles allows you to hide irregularities and surface defects.

Design techniques for laying tiles

Many people refuse to use stone tiles for interior decoration in the apartment, being afraid to add gloom to the room. However, these fears are groundless, because there are many compromise design solutions when it is possible to veneer not the entire room, but only one of the walls, a niche or a ledge. The main thing is to think over the general design concept for the whole room.

Imitation of protruding brickwork from chipped plaster is an interesting idea, but it must match the overall style. Sometimes protruding corners are trimmed with brickwork, but such a design decision depends entirely on the desire of the owner of the apartment.

If the room has a fireplace or stove, then you should take care of the appropriate decoration of the space around it. Designers do not recommend completely covering the walls with imitation brick for interior decoration, it is better to do it around the hearth or in a small area.

Helpful advice! The all-brick walls near the fireplace smear this decorative element, and it is completely lost. A combination of several finishing materials will help emphasize the hearth and give it charm.

When choosing a tile for a room, do not forget about its color. Too dark tones will give the room gloom and barracks. And sand tones, on the contrary, will add warmth and space. Proponents of conservatism may prefer the red tones of natural masonry in the living room, and choose white brick-like tiles for the bedroom.

Do not forget about such an important point when choosing a tile as its surface. It can be either smooth or matte. Experts truly believe that the shiny surface looks unnatural. However, if it is combined with the appropriate elements and decoration of the rest of the room, the result can be unexpected and interesting.

White glossy brick-like tiles are actively used for facing the kitchen or bathroom. The smooth surface is well cleared, does not absorb moisture and various pollution.

Features of installation of decorative tiles

Brick-like ceramic tiles for interior decoration in the form of panels are laid using the groove-to-groove snap-in technology, in this case the sheet imitates several rows.

If a single tile is a cut of one brick in size and shape, then many difficulties arise. In this case, it is necessary to lay it in a checkerboard pattern, otherwise the imitation of natural masonry will not work. Experts recommend using ordinary building crosses, which must be placed in pairs from two corners of ceramic brick tiles. This will make it possible to obtain an even masonry without displacement.

When installing facing bricks for interior decoration in the interior, do not forget about the seams. They should be wider than when laying ordinary tiles. To achieve this, you need to choose large wide crosses.

Upon completion of installation work, do not forget about grouting. It must be chosen according to the color of the tile or a contrasting shade. Professionals recommend abandoning the use of grout altogether, and using the remaining cement mortar or. This is due to the fact that real brickwork is not overwritten.

Regardless of the room for which the brick-like tile is chosen - for the kitchen, living room or bedroom, it looks beautiful and interesting in any interior. A wide range allows you to choose any material option and not violate the overall style of the home - red tiles, white brick, black clinker, etc. Laying is also not a laborious process, which allows even a beginner to do the job.

The decoration of the walls inside the premises of the apartment, as well as the facade of the house with decorative bricks or material imitating brickwork, has never gone out of fashion. However, unfortunately, it is not always possible to use real brick for interior decoration of housing, as it will make the floor slabs of multi-storey buildings heavier. In addition, it is not so easy to make an ideal masonry “for jointing”, because this requires at least a minimum experience of a bricklayer.

It is much easier to use other interesting ways to achieve the desired result. Imitation of a brick for can be made in different ways and, which is typical, is available for installation by anyone, even a novice finisher.

Given the fact that brickwork has been popular for decades and has been used in reproducing various interior styles, manufacturers have not missed this moment and have developed several types of material that can replace natural brick.

Such a finish is made in different forms - it can be flexible or rigid tiles that have the size of the end side of a brick, or large wall panels that cover an entire section of the wall at once, made from polyvinyl chloride (PVC), MDF or fiberglass.

Flexible tiles "under the brick"

Flexible tile that imitates brickwork is great for interior and exterior wall decoration. This modern material is not only decorative, but also a protective coating for surfaces and has a number of positive qualities - this includes resistance to external atmospheric influences, impact resistance, vapor permeability, inertness to microorganisms, as well as to ultraviolet radiation, and, of course, aesthetic appearance and a fairly simple process of processing and installation.

"Flexible brick" is easily mounted not only on straight flat surfaces, but also perfectly bends around the outer and inner corners of the premises.

A similar material is used for wall decoration inside apartments and houses, in particular, rooms such as hallways, corridors, kitchens, living rooms, loggias. It is also suitable for external, facade walls. It is very convenient to use such tiles for facing columns, fireplaces, small architectural forms, as well as in any areas where such a design is conceived. Regardless of the complexity of the surface configuration.

The tile can be used to finish the entire wall completely or fixed to its individual sections. Since the material has many colors, it is possible to make the finish monophonic or use tiles of different shades, harmoniously combining them with each other.

Installation of "flexible brick"

Installation of flexible tiles does not require complex electrical tools. It will only be necessary to prepare:

- smooth spatula 120÷150 mm wide - for mixing and applying glue;

- notched trowel with a comb 4 mm high and 150 ÷ 200 mm wide;

- building level with a length of 1000 ÷ 1500 mm;

- a ruler with a length of 1000 ÷ 1500 mm;

- marking colored cord for beating lines;

- a simple pencil;

- powerful scissors;

- a brush with a width of 12 mm for leveling the mortar in tile joints.

From materials other than tiles, you will need a primer for walls and a special

For installation, a dry mortar can be used - ordinary tile adhesive, but it is more convenient to use a ready-to-use composition packaged in plastic buckets. In any case, when purchasing a tile, you should immediately consult with the seller about the adhesive suitable for a particular material.

In order for the masonry to be even and neat, the wall must be put in order before installation begins, by cleaning and leveling its surface. After the leveling mortar has dried, the wall must be primed with an antiseptic compound, which will give the materials higher adhesion and prevent mold from appearing under the cladding layer in the future. When the primer is dry, you can proceed to the installation of tiles.

In addition, it is necessary to take into account the fact that installation work must be carried out at a temperature not lower than +5 degrees, otherwise the adhesion between the materials will be insufficient, and the tile may subsequently begin to peel off from the surface of the walls.

Brick imitation prices

brick imitation

The first step is to draw the surface of the wall into even zones, along which glue will be applied and the tile will be fixed. If the entire wall is to be completely lined, then it is imperative to beat off the upper and lower limiting lines.
The glue is not applied to the entire surface, but to separate lined zones, which are about 1000 × 500 mm. The layer of adhesive mass should be approximately 2 ÷ 3 mm - it is applied with an even spatula, and then distributed over the entire area to be lined with a notched trowel to obtain grooves of the same height.

The tile is glued in order, and if the first of the rows starts with a whole tile, then the second - with a half or one third of the "brick", depending on the desired location of the masonry joints.

Dividing a “flexible brick” into parts at any angle, without the use of any power tools, is quite simple: it is marked and cut along the line with ordinary scissors.

The seams between the rows can have different thicknesses - this parameter will depend on the preference of the master, but usually the clearance is left at 10 ÷ 12 mm. The selected size of the seams is taken into account immediately when marking the wall into zones for installation.

"Flexible brick" easily bends around ledges formed at any angle, as well as internal corners or rounded walls, if any, on the finished surface.

When the intended surface area is tiled, you must immediately level the mortar in horizontal and vertical joints, otherwise the glue will seize and it will not be possible to accurately level it. The smoothing of the solution is carried out with a relatively thin brush of medium hardness, lightly moistened with water.

The fact that flexible tiles do not require additional purchase of grout for joints can also be safely called the advantage of the material, since you do not have to make extra costs.

Video: flexible facing tiles with excellent imitation of clinker bricks

Rigid facing tiles "under the brick"

Clinker tiles

Clinker tiles are not used for interior wall cladding as often as other types of material that imitate brick, as it has a fairly high price. It is often purchased for facades, given its highest performance. However, it can also be used for interior decoration, especially if you have to line a stove or fireplace.

It is made from natural highly plastic clays, without the use of artificial dyes and plasticizers. The raw material is pressed and fired at high temperatures reaching up to + 1150÷1200 degrees. Thanks to this, clinker tiles are an environmentally friendly material with unsurpassed natural qualities of durability and reliability, which are multiplied during the production process.

Such a finishing material is excellent for both interior and exterior cladding. It has a very low moisture absorption coefficient, high frost resistance and wear resistance, inertness to temperature extremes and almost any chemical attack.

The decorativeness of clinker tiles is not inferior to its physical and technical characteristics, since the variety of design options allows you to choose the material for every taste and style of the interior of the premises or the facade of the building. Finishes can have a rough, glazed or natural, unfinished surface. On sale are tiles of different sizes and shapes, and this factor also allows you to realize the most daring design ideas.

Installation of facing tiles "under the brick"

As mentioned above, all tiles that have a certain rigidity are mounted on the wall in approximately the same way. The work will require the same tools as for the "flexible brick", and in addition, to cut this material, it will be necessary to prepare a hand circular saw or a grinder with a stone disc.

The work on laying the cladding from this type of material is more complicated, since the finish already has a significant weight, and after installation it requires careful sealing of the joints between the tiles.

The lining process is carried out in the following order:

Laying should be carried out on a prepared, primed and relatively even wall.
The marking of the wall surface takes place in the same way as for the installation of any piece facing material: straight lines are beaten off along the upper and lower levels of the masonry, then, it is recommended that the entire distance between them be calculated and divided horizontally so that the intended number of rows can be accommodated in this area masonry, with the obligatory consideration of the thickness of the seams between them. It is especially important to carry out this process if there is not enough experience in wall cladding - marking will help to make the masonry perfectly even.

When marking, 10 ÷ 12 mm should be allocated for each of the seams between the rows.

Further, the adhesive mass is prepared, which is selected in accordance with the type of material on the basis of which the finishing tiles are made.

The laying starts from the bottom row, which is carefully verified by the building level, since the accuracy of the entire wall cladding will depend on its horizontalness. If the first row starts with a whole, then the second and all subsequent even rows with ½ or ⅓ tiles.
Further, glue is applied to the wall with a spatula with a layer of 3 ÷ 4 mm. After that, the mass is distributed with a notched trowel, which leaves grooves of equal height, ensuring the most even distribution of glue when pressing the tile. When laying some heavy types of tiles (the same clinker), it is additionally recommended to apply glue on the back side of the facing material. Therefore, before starting work, you should definitely study the instructions attached to the package, which clarify the nuances of installing a particular material.

During the installation process, it is necessary to control the evenness of each of the stacked rows.

To ensure that the width of the seams between the tiles on the entire surface to be lined is the same, some craftsmen use special calibrator tabs of the same size. They are temporarily installed between the rows, and after the adhesive mass has set, they are removed and installed again, but already on the upper rows. As such calibrators, you can use a wooden glazing bead or silicone posts.

For facing external corners, special curly elements are used that are able to mask existing chips and make the corners neat and protected.

Upon completion of the masonry and after the glue has completely dried, the seams between the tiles must be securely and accurately sealed with grouts specially designed for this purpose. You can fill the seams in different ways:

- Use ready-made formulations in tubes, using a special gun.

- Place the mixed grout in a plastic bag, and then cut obliquely one of its corners to the width of the seam and gently squeeze the grout into the gaps between the rows.

Unlike PVC panels, MDF trim is not recommended for use in rooms with high humidity, but it is perfect for leveling the walls of hallways, corridors, insulated balconies, and living rooms.

Manufacturers also thought about the design of the corners, making special curly elements for this.

Fiberglass panels

Special mention should be made of fiberglass panels. This facing material is made on the basis of ordinary cement with the addition of glass fiber fibers, which increases the strength of the plates tenfold. For external finishing, panels can additionally be reinforced with metal elements, which increase the weight of the structure, but make it resistant to mechanical stress.

Reinforced only with fiberglass, the panels have a not particularly frightening weight, and dimensions that are relatively compact in thickness. The solution for their manufacture is colored in bulk, so the plates are not afraid of small chips and abrasions. Some manufacturers add colored fiberglass to the molding sand, which is somewhat darker or lighter than the main tone, but in perfect harmony with it - this gives a very interesting effect. In addition, additional application of paint on the surface of already finished and assembled products is allowed.

Well suited for interior decoration, but still more often it is used to transform the facade of the walls of the building.

Environmentally friendly plates do not make the walls heavier, as they have a small mass. They perfectly protect surfaces from moisture and mechanical influences, as well as from the penetration of radio emissions into the house, and have a number of other attractive advantages. However, the cost of such facing materials is quite high, so not every owner can afford such a finish.

Installation of panels "under the brick" on the wall

If the wall surface is sufficiently flat, then the panels can be fixed to it without installing a frame structure. Lightweight PVC boards are glued to a cleaned and primed surface using one of the polymer adhesives. For example, "liquid nails" are well suited for this.

Finishing panels based on MDF have a much greater weight, therefore, in addition to glue, they are fixed on the wall with dowels in four to five places.

Fiberglass panels can be fixed to a flat wall with cement-based tile adhesive.

In the event that the wall surfaces have significant distortions, they are corrected by fixing the frame structure, consisting of metal guides or wooden beams, set exactly in the desired plane according to the building level. Some manufacturers make special subsystems for their products, mounted on a wall or on an installed frame. In this case, panels are hung on special elements of subsystems.

Subsystems can have different designs, therefore, when purchasing cladding boards and their fastening systems, it is necessary to check compatibility and the presence of the attached installation instructions.

It is clear that if it is planned to mount the panels on a subsystem, the frame elements must be located in accordance with the feature of this model.

The simplest type of fastening is plastic panels made according to the principle of siding construction. They have a special perforated mounting plate in the upper part, through the holes of which the plate is fixed on the wall or frame. In this case, horizontal elements of the crate are fixed to the wall surface, at a distance of the visible part of the slab.

Facing brick prices

facing brick

Installation of any cladding panels starts from the bottom of the wall, usually from the corner elements.

Homemade options for decorating walls under brickwork

If you want to save money by making an imitation of brickwork on one of the walls of an apartment or house with your own hands, you can use the original techniques developed by craftsmen.

There are several options that do not require special costs for the purchase of facing plates or panels, and also do not create any particular difficulties in installation:

Independent production of tiles from expanded polystyrene with a thickness of 10 ÷ 12 mm. For this purpose, it is recommended to use extruded material with higher performance than conventional white foam.
Creating a brickwork relief using a stencil.
Reproduction of the desired pattern on the wall using masking tape.

Tile "under the brick" of expanded polystyrene

If it is planned to use the process of melting the edges of the foam plastic in the manufacture of tiles, then work should be carried out outdoors, protecting the respiratory tract with a respirator, since this material is combustible, and when burned and melted, it releases toxic substances.

The first step on the prepared leveled and primed wall surface, with the help of a ruler, a plumb line, a building level and a simple pencil, is the marking of the “brickwork”. The wall is drawn into horizontal stripes and vertical partitions, which determine the size of the brick and the seams between them and the masonry rows.
The second step is to mark the expanded polystyrene sheet on tiles of the selected size.

Then the material is cut into individual elements with a clerical knife. The number of such blocks should correspond to the number of bricks required to decorate a certain section of the wall on which the markup was made.

Further, in order to achieve the most reliable effect of imitation of a brick, you need to work on the resulting tile - this can be done in different ways. Its surface is treated with sandpaper in different or one direction, with a knife or other sharp instrument, notches and grooves are made on it. You can also use a heated soldering iron for this purpose.

Another option is to melt the edges and outside of the tile with a regular lighter or burner. In this case, the front surface acquires soft smoothed shapes.

After painting the tile in the selected color, its relief will be more pronounced. The application of paint can be done before the installation of the tiles or after the wall cladding is fully completed.

Coloring can be done with a brush or by spraying the coloring composition from a cylinder. The main thing is that the paint does not cause the dissolution or softening of expanded polystyrene - it is better not to experiment with organic-based compositions, preferring water-soluble ones.

Styrofoam tiles are laid according to wall markings using liquid nails glue, which is applied to the back surface with three points 3 ÷ 4 mm thick.
The final step will be the design of the seams between the bricks and rows.
It should be noted that if the design does not provide for the selection of tile joints in a different color, then the lining can be painted even after the grout solution has dried.

Imitation of brickwork using a stencil

In order to make an imitation of brickwork using a stencil, you will need a cement-based mortar. It is best to purchase it in the form of a ready-made dry mortar for plastering, as it already has all the necessary additives that make it plastic and easy to work with.

The solution can be made independently from two materials - it is a plaster and adhesive cement mixture, which are taken in 1: 1 proportions. To increase the plasticity of the solution, add a tablespoon of liquid detergent to 5 kg of the finished mixture.

The wall must be well cleaned, primed and dried.
The solution can be applied to its surface with a wide spatula or simply with a rubber-gloved hand. The thickness of the applied layer should be equal to the thickness of the stencil strips. This moment will depend on what surface the brick should have - smooth or rough.
Further, so that the stencil does not have “stickiness” with the layer of the applied solution and is easily separated from it, it should be moistened with water - this can be done with a sponge or a damp cloth. If the stencil is made of rubber, then you can simply dip it into a basin of water, but in this case you need to wait until its excess stacks, otherwise excess moisture can ruin the whole job.
After that, the stencil is pressed against the applied fresh plaster and gently pressed, so that the relief of the brickwork remains on it.
Further, the stencil is removed and applied further, next to the freshly pressed relief. Here you need to try and attach it so that the masonry is even, and its horizontal seams do not skew.
When the relief is applied to the entire surface, it is left to dry completely.
After drying, the wall should be completely covered with one color - usually light shades are chosen for this, since it will be easiest to apply any color on them, as well as highlight with a dark shade or leave all the masonry seams light.

Painting imitation brickwork is already a creative process, so you can afford various fantasies. In this case, of course, it must be borne in mind that the chosen color will set the mood for the entire interior of the room.

Creating a brickwork relief using plaster and masking tape

For this technology of reproducing brickwork imitation on the wall, the composition of the cement plaster mortar and masking tape already mentioned above will be required. Some masters even use electrical tape, however, it sticks worse to the wall, and high-quality masking tape has excellent adhesion to any surface.

The width of the tape should be no more than 14 mm, and if you could not find an adhesive tape of this width, you will have to buy a wider one and carefully cut it right in the skein along the width in two. If its edges are not perfectly even, this is not at all scary, since this factor will not affect the accuracy of the relief, but rather, it will play into the hands.

The first step is the prepared surface of the wall to be lined under the brickwork.

Further, masking tape is glued along all the marked lines on the wall. It should be fixed in such a way that the edges of the horizontal segments of the adhesive tape extend beyond the edges of the surface being formed, and the solution should not be applied to them, and the vertical segments should be well glued to the horizontal ones, always on top of them.
Then, on the surface of the wall, over the pasted lattice of adhesive tape, using a wide spatula, a solution is applied, with a layer thickness of 5 ÷ 6 mm - the height of the relief will depend on this parameter. Do not apply too thick a layer, otherwise you will have to cover the seams with grout.
After applying the solution completely to the entire wall, it can be walked over with a wet rubber glove to create a surface texture. If you plan to leave the surface of the “bricks” even, then you should not touch the mortar layer.

The most interesting stage in this method of imitating brickwork is the removal of masking tape, since after this operation the relief of the wall will be immediately visible. Several strips of adhesive tape are picked up from one of the free sides and begin to gently peel off from the wall, and as a result, seams between the “brick tiles” are formed in place of the peeled off tape. After removing the tape from the entire surface, the wall must be left to dry completely.

It is recommended to dry the wall before painting - this operation will make the surface more pliable for the next stage - painting, as the paint will lie on the surface evenly and will not be absorbed into the plaster layer. What shades to choose for the wall - it already depends on the preference of the master.

Video: How to imitate brickwork with plaster and masking tape

From all of the above, we can conclude that the construction market has an overabundance of various materials that ideally imitate brickwork or other stone surfaces. Sometimes the quality of the imitation is such that, when finished, it cannot be distinguished from real brick in terms of texture and color. Well, if the finished tiles or panels do not fit into the family budget in any way, then it is quite possible to use one of the more economical methods and decorate the wall using affordable materials for this.

Interior decoration with clinker bricks is an elite class solution that only wealthy people can afford. You can buy clinker bricks for interior wall decoration in Moscow at a price of 18 rubles apiece.

Consider what exactly attracts in this option wall cladding:

Excellent sound insulation performance is achieved due to the large width of each clinker product. The structure of the material also contributes to the complete neutralization of the sound wave, taking all the impact on itself.
The combination of color schemes and textured surfaces provides designers with complete freedom in interior design.
There are legends about the strength and resistance to exerting loads of clinker. A special industrial manufacturing technology has been developed over the centuries. Numerous attempts have led to the successful completion of the search for the ideal formula of the chemical composition.
Environmental Safety. Clinker is a "green" material in terms of compatibility with the environment and harmlessness to living beings.
The appearance of clinker bricks for interior decoration creates an atmosphere of fundamentality and wealth.

Carrying out facing works

The preparation of the surface to which the bricks will be attached is to create an ideal flat plane. All small irregularities, bulges and bends must be eliminated. Holes and cracks must be sealed with mortar.
Processing with a special moisture-resistant composition, which will also create an additional dust-proof layer of bricks from particles from the wall.
Facing is made in the direction from the bottom up. It is necessary to carry out operations with due care and precision for the correct joining of the seams of the edges of clinker bricks. For a more expressive look of light tones, it is recommended to additionally paint the gaps between the products in a darker color.
It is not worth making additional coloring, because. the color of interior clinker is extremely resistant to chemical agents and UV rays. Over time, it does not fade due to the special chemical composition.

It is also impractical to strengthen the bearing supports and the foundation, the products are light in weight and do not exert increased loads on the system.

Differences from other options

It serves as an alternative to brick. It is cheaper and installation work in this case is also simplified. However, the tile does not give that feeling of reliability and solidity of the structure, which is typical for brick blocks. In addition, it does not have high rates of heat and sound insulation.

You should also distinguish between the concepts of decorative stone and brick. The sizes of clinker bricks, although varied, are still strictly standardized. Facing stone, on the other hand, is a product of various shapes and textures, which is folded into a mosaic.

In the construction industry today, a variety of decorative clinker is extremely popular. This type of brick for interior cladding has a lot of operational advantages and is distinguished by unique physical and technical characteristics. Use of finishing material, both in household, and in commercial conditions is allowed. An extensive palette of colors and textures allows you to implement design ideas of any degree of complexity (full finish, combination of materials, surface zoning).

Advantages and style of decoration

Among the key positive qualities of clinker material:

resistance to temperature changes and moisture;
frost resistance;
ultimate service life;
mechanical resistance to operational defects;
unpretentiousness in care.

Using this, you can equip the premises in the following styles:

loft - maximum free space and ease of environment;
hi-tech - most furniture products are combined with white clinker;
English style is an ageless classic in which brick is combined with wood and metal;
country - yellow or milky white brick complements shelves, racks, chairs and other wood products, which determines the originality of the interior.

Benefits of cooperation with Bauff

Our online store offers each client to buy building materials from reliable manufacturers at competitive prices. Leave a request or contact the company's managers directly to purchase clinker of any color. Thank you for choosing Bauff!

String(76) "Interior clinker"

Decorative clinker brick is used to finish the hallway, corridors and entire rooms. Due to its strength, smoothness and attractive appearance, this material is great for walls not only in residential areas, but also in offices, photo studios, cafes, bars and other establishments. Clinker bricks for interior decoration can be used in combination with other materials to implement design ideas, for example, when zoning space.

Material Features

Clinker brick is characterized by the following advantages:

resistance to temperature extremes, hygroscopicity, low thermal conductivity, moisture resistance;
long service life;
resistance to mechanical damage, chips, cracks;
unpretentiousness in care.

Clinker brick is suitable for creating interiors in styles such as:

loft. "Brutal" masonry creates a feeling of freedom and ease;
high tech. Here, white brick or material in the color of the furniture is best suited;
English style. In spacious rooms, the clinker brick finish goes well with wood and metal, creating a harmonious and complete design;
country music. Yellow and milky-white colors of brick in combination with wooden shelves, racks, chairs and other furniture create coziness and a special flavor.

Our offer

The KlinkerStone online store offers to buy clinker bricks from Feldhaus Klinker and other manufacturers for interior decoration. You can purchase material in white, sand, terracotta, burgundy, dark gray, which fully corresponds to the concept of interior design. To order products in the required volume, select a shade from the catalog and place an order through the "Basket". You can also leave a contact phone number on the site, and the company manager will call you for a free consultation. We organize delivery in Moscow and the region, we offer self-delivery and special conditions for customers from the regions of the Russian Federation.

Categories

Popular