Shower faucet horizontal installation. Bath faucet horizontal installation. How to replace a broken eccentric on a faucet

Sooner or later, but there always comes a time when the owners of the apartment have to change plumbing that has served its time or, in their opinion, is morally and technically obsolete, does not meet the increased requirements for functionality or even external design. One of the questions that are most often asked at the same time is “which bathroom faucet with shower should I choose?”.

This question is not as simple as it might seem at first. It was not difficult with this business even 20 ÷ 25 years ago - you go to the store, and, if you are lucky, you buy what is there, and you are already satisfied with it! But the modern range of plumbing devices offered to the consumer can even be confusing - you can make the right choice only if you are at least a little versed in the device, classification, manufacturing materials and other issues.

And the appearance of the crane, which, of course, is very important, still should not become a decisive selection criterion. Practice shows that low-quality products of dubious manufacturers are most often given an appearance that attracts increased attention.

If a new mixer is installed in place of the dismantled one, then, of course, the choice of models at their location is not very wide. But in the case when it is planned to overhaul the interior of the bathroom with the laying of new engineering communications and the replacement of all plumbing equipment, the owners have “space” in terms of selection the most optimal sample.

1. Most common and the most commonly used option in the bathroom is a wall-mounted faucet with connection to pipes hidden by decorative trim. If the pipes are not planned to be “removed” into the wall, then the mixer can also be mounted to vertically located open risers for supplying cold and hot water.

The "classic", the simplest type of connection - using ¾ inch union nuts using rubber (silicone) gaskets to horizontal nozzles. For precise centering of pipe and mixer axes and for changing from ½ to ¾ ʺ, usually, eccentrics are used.

In order not to leave the installation connection points visible, decorative caps are pre-wound on the thread of the eccentrics. Further installation - accurately set the center distance (shtikhmas) and carefully, without distortion, tighten the union nuts.

1 - protruding threaded part of the eccentric 3/4 ʺ.

3 – mixer union nut.

4 - sealing gasket.

In terms of ease of installation, such mixers have no equal, therefore, probably, they are the most widespread. In addition, models with a similar connection scheme are among the most inexpensive in price.

If there is a desire to bring novelty to the interior of the bathroom, then you can also purchase a wall-mounted faucet, the connection points of which are completely hidden from view by the mono-case of the device itself. The principle of connection in this case does not change much, but the installation itself will require more effort, accuracy and ingenuity, the obligatory following of the instructions developed by the manufacturer. But these "troubles" are justified by the very original appearance of such devices.

A rather expensive and difficult to install option, when only controls, a spout and a shower head with a hose are located on the wall, assembled according to the monoblock principle or spaced apart by separate elements on the surface.

Such mixers are a set of parts and assemblies designed for external installation and for installation in the thickness of a wall structure. A rigid or flexible connection is provided from the water pipes to the control unit and from it to the spout and shower. High-quality blocks of internal installation are protected by special cases that are not afraid of being embedded in mortars.

Such devices are very expensive, and in order to install them yourself, considerable experience is required in plumbing, general construction, and decorative and finishing works.

2. The next type of mixer installation is on the bath itself. Of course, we are talking about either bathrooms that have specially designed mounting platforms with holes, or acrylic or fiberglass, on which neat holes can be drilled for further installation. Several options are also possible here.

One of the simplest options is to use one hole, and the mixer itself is very similar to its "brothers", which are installed in or on kitchen sinks.

The principle of installation and connection here also does not differ much from mixers installed on sinks.

Another option is a kind of "retro style". Decorative pipes are installed in the mounting holes of the bathroom, supplying hot and cold water, and the faucet itself is connected directly to them.

Of course, the stand-pipes themselves are an integral part of the mixer set, they are made in the same style with it. Often they have very bizarre forms, emphasizing the unusualness of the ensemble being created. The connection to such mixers is carried out from below, under the bath, and most often flexible hoses are used for this.

For modern style bathrooms, the faucet controls, spout and shower can be spaced horizontally on the edge of the tub.

The installation of such devices should also not cause any particular difficulties for the owner, who is familiar with the basics of plumbing technology. The kit is always accompanied by detailed instructions with an assembly drawing, such as, for example, as shown in the figure:

An example of connecting a four-position mixer with installation on a bathtub:

1 - a mixing unit with an adjustable single-lever cartridge-type tap.

2 - tap-switch of the flow "spout - shower".

3 - cascade type spout.

4 - shower head, which is located in a special glass (pos. 5).

6 and 7 - flexible piping from the water supply network.

8 and 9 - flexible connections connecting the main components of the mixer.

Flexible hoses 6 to 9 are usually not included, purchased separately depending on the installation. But these are the most common water hoses with ½ inch connectors. It is always possible to arrange the elements of the mixer on the bath in a convenient location at the right distance from one another.

10 - flexible hose with an adapter for connecting a shower hose.

11 - retractable shower hose passed through a glass (pos. 5). When not in use, it is hidden under the bathtub.

Installing such a mixer, subject to accuracy and using high-quality components, should not be difficult.

In some models, instead of a flexible connection between nodes, a rigid one is used. This will require the most accurate selection of the mixer for the existing holes in the bath, or increased accuracy when marking, if the installation sockets are drilled independently.

Another variation when installing the faucet on the bath - all controls are placed on one horizontal panel located on the side.

Due to the fact that such a design turns out to be quite massive, and the load falls on a localized area, very often such mixers have their own racks, which rest against the floor. A window is cut out on the side of the bathtub, in which the mixer is mounted, on the acrylic or fiberglass wall itself, and at the same time it does not experience weight loads.

In addition, there is another possibility of installing the mixer - not on the bath itself, but close to it, from the end or side. At the same time, it will not be difficult to cover the structure itself with a decorative finish, for example, by mounting the box and lining it with ceramic tiles.

3. Following in line with the fashion trend to install a bath not in a “classic” place - near the wall, but in the center of the room (if there is enough space), the designers have developed special models of faucets that are installed on the floor.

This, of course, is a rather rare case of application in everyday practice. The cost of such models is high, they require special plumbing pipes hidden under the floor surface.

However, the demand for faucets of this layout is still stable, and the model ranges are represented by products in both retro style (for example, as shown in the picture above) and innovative, modernist execution.

The main types of mixers are considered. Now you should take a closer look at their components and accessories.

The difference between mixers by "controls"

Any bathtub/shower faucet involves mixing water from cold and hot pipes to the desired temperature, as well as the ability to switch already mixed flow onto a spout or shower head.

Adjustment of cold and hot water supply

Two valve flow mixing system

Once such a system was, in principle, the only one. And despite the fact that more modern approaches to mixing streams have appeared, a similar scheme successfully competes with them. Moreover, it is she who is used in all mixers made in retro style.

"Classic of the genre" - mixer with two valves

The standard layout is two taps with handwheels located to the left and right of the spout. Each valve regulates its own flow - cold or hot water, and the mixing itself takes place already in a separate chamber of the plumbing fixture.

Such a scheme is distinguished by the simplicity of the device, it is easy to repair. Setting the water temperature is not difficult in itself, but the simultaneous regulation of both the flow rate and the degree of heating is rather difficult. However, for systems with autonomous instantaneous water heaters (for example, gas water heaters), it is recommended to use just such a scheme.

Bushing cranes are used as locking and adjusting mechanisms. With external similarity and with the same fitting thread for installation in a mixer, they can differ significantly.

Crane box with rubber gasket - stopper

Crane boxes with a rubber gasket that blocks the flow of water. The rotation of the flywheel through the worm gear is converted into the translational movement of the rod with a valve located at the end, on which there is a round rubber gasket. It may take several turns from full opening to closing.

The advantages of such a faucet are simplicity of design, the possibility of replacing the gasket, undemanding to the purity of the water. Among the shortcomings, there is a rather rapid wear of the seal, the resulting backlash in the mechanical transmission of rotation. There is another feature that will be felt at high temperatures - the imbalance of the set heating level. The fact is that the rubber disc changes linear dimensions, thickens and increases radially, with strong heating, thereby violating the set clearance for the passage of water. It is possible that during the washing process you will have to repeatedly adjust the temperature.

A completely different device and principle of operation for a crane box with a ceramic valve. The valve itself consists of two plates tightly ground to another with "windows" cut into them. The rotation of the plates relative to each other leads to a change in the area of the lumen or to its complete closure. The operating cycle of such a crane can be limited to one revolution, half or even a quarter.

Such taps are very convenient, they allow you to accurately set the flow rate through them, which will not change with a temperature drop. The disadvantage is increased sensitivity to water pollution - solid inclusions caught between the ceramic plates can very quickly lead to their wear and failure. If you decide to install such axle boxes, you should also think about a reliable filtration system. By the way, mechanical water purification will be useful for any type of faucet.

Replacing a failed axle box is a simple task for any owner. Their cost is also low - this largely determines the wide popularity of mixers of a similar scheme.

Find out which one to choose, as well as check out the varieties and installation, from our new article.

Single lever control scheme

Mixers equipped with one lever for simultaneous regulation of both flow rate and temperature are the most popular among consumers.

"One-handed" mixers are very popular nowadays

The lever moves in two planes, and the regulation and mixing of flows is carried out in a special cartridge.

This is what a replacement faucet cartridge usually looks like...

There are also two windowed ceramic plates inside the cartridge. The principle of operation is shown in the diagram below:

... and here is how it works

The cartridge lever is shown as a dotted line.

On fragment “a”, the lever is lowered, and the plate associated with it completely blocks the flow of water from both hot and cold supply.
When the lever is raised in the central position (fragment “b”), windows open for water access to the mixing chamber from both feeds, and the passage area is equal to the left and right. The lifting height of the lever will correspond to the width of the opening of the fluid channels, that is, the flow intensity is regulated in this way
Moving the lever to the left or right (fragment "c") increases the free passage area for one of the feeds, respectively, reducing the opposite one, up to its complete closure. In this case, the total cross section of the water flow, in principle, does not change. This is how the outlet water temperature is controlled.

A slightly different scheme can also be used - the cartridge does not consist of ground-in plates, but is a hollow sphere with windows for water to enter it, moving relative to the supply holes.

A quality cartridge can last a long time. When choosing, you should pay attention to what the valve itself is made of. There are products not with ceramics, but with polymer plates, and, despite the assurances of manufacturers, their service life is much less. The cheapness of the product in this case does not justify the need for frequent replacement.

The control lever is not necessarily located in the center - there are many other design solutions

The layout of the mixer itself with one lever (joystick) can be very diverse. The developers offer models with both top, and front, and side levers, but the principle of operation does not change.

Mixers with built-in thermostat

If funds allow, then you can purchase a mixer, the water temperature in which is adjusted according to the thermostat scheme.

Usually on such devices there are two flywheels equipped with a locking system. On one side, the flywheel sets the exact temperature of the water at the outlet - for this, an appropriate scale is applied to it. On the other side of the mixer, a flow intensity regulator is structurally placed - it can be changed smoothly or stepwise in various models.

The advantages of this type of mixers are obvious:

Complete safety is guaranteed for the recipient of water procedures. Even if there is very hot water in the water supply, in the boiler or at the outlet of the instantaneous heater, there is no risk of scalding - from from A shower or shower head will run water at a strictly adjusted, pre-set temperature.
Water consumption becomes much more economical. The regulation device will produce the required pressure at the outlet, regardless of the pressure level in the pipes. In addition, such a mixer will also save in terms of energy consumption for heating water - only the right amount of it will always be spent.
Many of the models are equipped with safety devices, clearly and responsive to possible changes at the inlet - pressure drops or even interruption of the supply.

There is only one drawback of such mixers - you need to be prepared to pay a fairly “round” amount for convenience.

The most modern are mixers equipped with electronics, which are responsible for the thermostatic regulation of the outgoing water, and for the pressure, and for switching operating modes.

Such models can be equipped with touch controls, liquid crystal display panels showing the settings and current system parameters. Of course, the cost of such devices is very impressive.

Spout-shower switching mechanism

If we do not take into account the most “fancy” models, in which the electronics “manage” the switching of modes, then the mixer must have one or another external control that has the task of redirecting the mixed flow of water from from pouring into the shower and back.

The switching mechanism itself (it is often called " divoter", the name " divertor" is found) can be of several types. Some of them are shown in the figure:

Schemes of the device of switches "spout - shower"

a - spool type switch. The rotation of the lever to switch modes is transmitted to the eccentric shaft. That, in turn, moves the spool rod to the extreme positions, on both sides of which there are plugs with rubber seals. Thus tightly overlapping one from the exits faucet - either a shower or a spout.

The advantages of such a mechanism are simplicity, reliability, it is easy to sort it out on your own, replace worn parts.

The disadvantage is the rather rapid wear of the rubber gaskets, after which unwanted water bypassing begins. In addition, there are cases of breakdown and jamming of the eccentric mechanism.

b - diver with a spherical valve. The ball connected with the flywheel axis is surrounded by polymeric gaskets tightly adjacent to it. There is a channel in the body of the ball, which, depending on the position of the switch, connects the outlet from the mixing chamber either with a shower or with a spout.

The system is very simple and reliable. There is simply nothing to break in it, and its service life is limited only by the gradual wear of plastic gaskets. But such divers are usually integrated into the hull, and in case of failure, as a rule, entail the replacement of the entire mixer.

c - cartridge type switch. The design is somewhat similar to the cartridge of a single-lever mixer - two ground-in ceramic plates with windows, the position of which determines the direction of the water flow.

Such switches are famous for their very light, smooth operation, duration of uptime use. The cartridge is located in the mixer body, and in case of signs of wear of the plates, it is easy to replace it with a new one.

Extremely widespread switches of the exhaust principle of operation.

Their body uses a poppet type valve, connected by a stem to an exhaust handle (button). By default, the valve, under the influence of a spring, is held in a position that interrupts the exit to the shower, leaving a free path for water to the spout.

If you pull the button, the valve will change position, shutting off the spout and opening the shower hose into the connection. The valve is held in this position by the pressure of the water. If the pressure decreases or stops completely, then the spring will return the valve plate to its original position, tearing off the outlet to the spout. It is very convenient from the point of view that if one of those who took water procedures forgot to switch the diver, then there is no risk of getting a “water charge” by the collar from a shower head hanging on the wall.

Often there is not enough pressure in the plumbing network to keep the switch in the “shower” position. Faucet developers provide for such an opportunity - the button can be fixed in an extended position by turning around the axis to the left or right by 90 degrees.

Such switches are simple in device, inexpensive, but it is often difficult to find a replacement or repair kit for a specific mixer model if the device is integrated into its body.

Based on what was said about the flow switches above, it is worth dwelling on one more of their features. Look at the picture below. It would seem that it has three almost identical mixers. However, they differ radically in the location of the diver.

a - the switch is integrated into the body from the mixer. Such a scheme is considered the most reliable, since leakage is practically excluded. Another advantage is the compactness of the entire device. The diver can be placed as shown in the figure, or it can be placed on a fixed spout, which, in principle, is structurally part of the body.

The disadvantage of such a scheme: if the switch fails, then the repair is very difficult (unless, of course, it's not a cartridge), and in some cases - and not possible at all. Thus, the failure of one unit can lead to the replacement of the entire mixer.

b - the switch is a separate block, which is placed between the mixer body and the movable spout. Advantages - high versatility, since the thread size usually fits most models of this type. The failure of the mechanism is just a minor nuisance, since acquiring a switch and replacing it in this arrangement is a couple of trifles.

The disadvantages are obvious. Firstly, an extra connecting node appears, that is, a vulnerable spot. Secondly, when using a shower, dynamic forces are transferred through the hose to this interface of the body, switch and spout, which leads to its loosening of the assembly and the appearance of leaks. And thirdly, the height of the entire mixer assembly is seriously increased, which can be very inconvenient. However, due to its high maintainability, the scheme has the widest popularity.

c - this option is most likely a tribute to "vintage", and not a rational approach. It will hardly be convenient to use a shower that is connected by a hose directly to a movable spout, and even so that the point of application of force forms a lever with respect to the gander's axis of rotation. And how long will the seals and threaded connections between the body and the spout last in this case? As is clear even from the figure, in case of any breakdown of such a switch, it will be necessary to look for a new spout. True, nothing will prevent the owner from switching to option "b".

Spout design

Long swivel spouts are still at the peak of popularity. They are convenient in that move location jet falling from it, especially in those cases when you need to draw water into a bucket, basin, or if washing and rinsing clothes is being done in the bathroom.

Once upon a time, during mass urban housing construction, the typical layout was the scheme, in which it was located at the end of the bath, somewhat rising above the edge and blocking it. This is where the design of faucets with a long curved spout came from, which could be rotated either for use in the bath or for washing.

Today, most owners prefer to put separate devices at each draw-off point, but, nevertheless, this design shows an enviable survivability.

When choosing such a mixer, it is necessary to take into account the length of the spout, the sector of its rotation. The rotating knot is always a weak point, so you should pay special attention to its quality.

Faucets with a fixed short spout, which is essentially a continuation of the body, are deprived of such shortcomings. Yes, the jet is always directed to the same point, but this is quite enough for taking a bath. But the device itself is much more compact, lighter, more reliable in operation.

Faucets with a short fixed spout are more reliable

Design execution of fixed spouts can be very different - from retro style to the most unusual modern forms.

A completely separate niche is occupied by spouts the so-called "cascading" type. Water flows out of them like a beautiful waterfall. At the same time, its consumption is much higher than when using conventional spouts.

It certainly looks very original. And how to evaluate the practicality of such a spout from the point of view of everyday use is, of course, a moot point.

Shower head and connecting hose design

Undoubtedly, the most important elements of the entire bathroom faucet set are the shower and the hose or pipe leading to it. Let's take a closer look at these accessories.

The simplest option is watering cans, which simply break the water stream into many thin jets, and do not have any other functions. It is interesting that such souls are becoming less and less common - they are gradually being replaced by more modern multifunctional models.

Nevertheless, for many such a simple design is quite enough. And the designers of manufacturing companies, for the sake of consumers, produce ordinary watering cans in a wide variety of designs.

However, a discerning buyer will often prefer to choose a shower head with switching modes. In the simplest models of this type, there are two or three modes, for example, normal, soft with flow aeration, and hard massage jets.

Models are also produced with a significantly larger number of available modes - the only question is how often they will be used in practice.

The material for the manufacture of watering cans is plastic or metal. Polymer watering cans are cheaper, but the quality is lower, they can crack if handled carelessly. On the other hand, it will not be a pity to replace them from time to time. Metal watering cans are more durable, but also heavier, and if accidentally dropped on the enamelled surface of the bath, they can damage it.

The most important attribute is the hose that connects the watering can to the mixer ( divoter).

The usual inexpensive hoses in a spiral metal sheath with a rubber or plastic tube inside are extremely short-lived. From constant use, the braid begins to diverge, frays the cabin with sharp edges, and the hose can be safely thrown away. Another disadvantage of the metal braid is that it acts abrasively on the bath - acrylic models especially suffer from this.

Such hoses are gradually being replaced by silicone ones, which can have a metallized, nylon, foil inner or outer reinforcing braid. Such hoses last a very long time, look very attractive, do not require special care - unlike metal, they do not leave traces of limescale. And if you really want to have a metallized surface, then it’s better to choose a herringbone silicone hose sheath - it looks beautiful, and it won’t be demolished.

The length of the hose is very important. The choice should be made based on the actual size of the bath, the height of the people who will take water procedures. However, too long hoses will also become an inconvenience. It is optimally considered - about 1.5 ÷ 1.6 meters.

As a rule, all hoses are fully standardized in terms of threaded connections to both the faucet and the shower head, so it will not be difficult to replace in case of wear. By the way, the connection nodes are perhaps the most vulnerable places, as they are constantly subjected to twisting stress (this is especially true for the “hose-watering can” node). To avoid a quick breakdown, it is worth looking for a modern model of a hose in which a swivel is installed - a plastic plain bearing that allows the shower head to rotate 360 ° relative to the connecting fitting without any damage.

The optimal solution is a hose with a slide bearing at the junction with the shower head

It is worth paying attention when choosing the convenience of a bracket for a shower head. On some faucet models, it is located directly on the body, on others it is included in the wall mounting kit. Often, special racks are offered that allow you to install the shower at the right height, while simultaneously adjusting its angle of inclination for comfortable taking procedures.

Such racks can to be included in the set of bath accessories, or to be purchased separately.

Read the article, as well as how not to get confused in their diversity.

Faucet models that combine both a shower on a flexible hose and a stationary sprinkler stand somewhat apart.

It is very convenient - you can always arrange a “tropical shower” mode for yourself. In such models, an additional switch is provided that redirects the flow either to a flexible hose or to a stationary pipe mounted on the wall.

Faucet material and outer coating

Whatever model was the mixer itself, the material of its manufacture is of paramount importance. Alas, in this matter, many are promiscuous, for which sometimes you have to pay with the purchase of a new device.

Silumin - an alloy of aluminum and silicon additives, has only one advantage - low cost. Although it seems to be a metal, it is extremely porous and fragile. Some details from silumin can be easily broken with the force of the fingers. In addition, silumin is not protected from oxygen corrosion, and its fragility and brittleness are constantly increasing.

At the same time, such mixers are actively and quite successfully “made up” for quality products, especially by the manufacturers of our “great eastern neighbor”. But no matter how beautiful the device may look, immediately refuse to buy a silumin mixer - it will not serve for a long time.

Stainless steel products show themselves well in everyday practice. As a rule, all of them have a high-quality chrome plating. There is only one drawback - the excessive massiveness of the mixer.
The best metals for any plumbing products are copper alloys. Brass or bronze faucets are not subject to corrosion, withstand the most severe thermal and mechanical loads, and do not have any negative chemical effect on water. And by longevity they have no competitors at all. Naturally, all this will be fair if really high-quality metal is used.
Ceramic materials can be used for the manufacture of individual mixer assemblies. It looks very cool, especially if the bathroom is decorated in retro style. However, it should be remembered that ceramics are afraid of impacts, and they should be handled with extreme care in order to prevent chipping of the surface or the formation of cracks.

There are mixers in which a large number of external parts of the body are made of high-strength ABS plastic. As a rule, these are modern models with thermostatic regulation. In the "classic" versions of mixers, leading manufacturers do not use polymers for the manufacture of bodies.

So, it is best to purchase a mixer made of brass or bronze.

Hiding the noble color of bronze is simply unwise

Bronze is usually not "hidden" behind any external coating - its noble color in itself is an adornment of the mixer. It can have a mirror finish, imitating even gold, or be matte, covered with patina.
Brass faucets are usually covered with a decorative coating. It can be chrome-nickel plating - from mirror-shiny to matte, pure silver or with interesting tint filling for various types of metals.

For lovers of a non-standard approach to bathroom interior design, models with a highly resistant, durable polymeric colored enamel coating are offered.

Baths made of composites imitating natural stone - granite, marble, etc. are popular. You can also match them with a faucet that has a similar external design.

Faucets with composite coating "under the stone"

In a word, and in terms of the external design of the mixers, the choice is quite wide. But even if some model really liked, you should not immediately purchase it recklessly - you need to take into account some more recommendations.

Useful tips for choosing a bathroom faucet

First of all, if such an opportunity is given, you should purchase products of well-known brands.

Mixers of the German companies Grohe usually do not cause any questions about the quality of workmanship. , Hansa, Hansgrohe, Danish Damixa, Italian Mamoli and Carlo Frattini Visentin, Russian Aquatica, French Herbeau and Jacob Delafon, Swedish Gustavsberg, Finnish Oras, Spanish "Teka", American "Ideal Standard" and "Supergrif", Swiss " Geberit»

If the name of the manufacturer does not mean anything, then it would be reasonable to give a search query on the Internet, and then carefully read the company's website, or even better, read real, and not far-fetched product reviews on the forums.

But if suddenly the name is clearly “disguised” as a well-known brand, for example, you come across a Teko, Herbean, Mammoli or Grehe mixer, you should immediately say a resolute “no”. And do not listen to the seller's assurances that these products are manufactured under license - no self-respecting manufacturer will allow his name to be distorted. This is an absolute fake. no matter how shiny and beautiful she looks.

Never buy such plumbing from your hands, from random sellers in the bazaar - with a very high degree of probability you will run into low-quality counterfeit goods.
In any normal salon, they are required to present documents confirming the authenticity of the product, put a mark on the date of sale, from which the warranty period will begin to count. This should not be neglected - the mixer can be quite expensive, and leading manufacturers give good guarantees for several years. He always pays special attention to issues of quality and his own reputation, therefore, if the device fails, you can count on a replacement according to a complaint or compensation for losses.
Be sure to check the completeness of the delivery - everything must exactly match the product passport.

You can find out and also study the nuances from our new article.

We hope that the information provided in the article has given the reader sufficient information on choosing a bathroom faucet. Choose from the catalogs a model that matches your tastes, desired functionality, bathroom design style and personal financial capabilities, and go to the salon for a purchase.

Video: how to choose a bathroom faucet?

A bathroom faucet is one of the important plumbing items that ensures the comfort and functionality of the room. Designed for mixing hot and cold water.

There are many types of mixers available. To select the right product, the design, equipment, type of installation, type of control, additional equipment are taken into account.

What to pay attention to

Spout shape:

arcuate the mixer is made in the form of an arc. The upper point in relation to the outlet of the spout is located higher. Additional space under the crane is formed.
Straight. The pipe is guided horizontally or at an angle.
Rectangular. Spout bends in one or two right angles. Such products are more difficult to manufacture, more expensive.

spout type

Classical. The mixer is made in the form of a tube. Common to most designs. Straight, curved, corner products with a round, square, triangular section.
cascading. Water enters through outlets (thin slots or wide chute). The result is good throughput. The original appearance of the product resembles a waterfall. But the high cost makes the device not common.

Control type

single valve. Differs in one supply, water pressure is regulated. The temperature of the liquid does not change. Designed to supply hot or cold water only. Installed in quantities of one or two (English style, when hot and cold water are mixed in the sink).
Double valve. Classic system of two faucets with opposite temperatures and one spout.
single lever or joystick. The design is represented by one lever, which adjusts the temperature and pressure by turning to the sides (degrees), up and down (flow force). Models with ball valves are difficult to adjust.
Contactless. Contact with the mixer is not required, the user raises his hands, the water automatically (sensors built in) opens. This guarantees economical consumption, but eliminates temperature control.

Shower set. The design consists of a hose or pipe with a watering can at the end. The advantage is the complete set of necessary cranes.

Mounting method

Wall. The mixer is mounted vertically to the wall.
Horizontal. The faucet is attached to the side of the bathtub.
Floor. With the help of a special stand, the mixer is mounted on the floor. Used as a design solution, requires additional space in the room. convenient if the bathtub is freestanding and not near the wall.
Embedded. The crane is mounted in a hidden way. Usually fully equipped behind the wall of the room or under the bathroom. Remain available, control panel and spout.
This method of installation saves space, but it is not always possible to carry out a convenient tie-in due to the placement of pipes. Another difficulty will be maintenance, repair work in the event of a breakdown.

Long bow. Universal products are designed for use in the bathroom and washbasin. The flow of water is directed by changing the turn of the tap.

swivel spout. Allows you to rotate the spout and direct the flow of water into the tub or sink.

Auto switch to shower/bath. Automatically works in one direction when one faucet is closed, returns in the opposite direction to the sink. This prevents flooding in case of accidental activation of the watering can.

Housing material

Brass. The composition is made by a combination of copper and zinc. The low price of the product gives increased strength, eliminates the occurrence of corrosion. Therefore, the material is one of the most common.
Silumin. The alloy includes aluminum and silicon, is characterized by oxidation resistance, but is not strong enough. It is used in budget models.
Stainless steel. The material is durable and expensive models.
Zinc. Inexpensive but fragile material. The disadvantage of products is considered to be low corrosive qualities.
Granite. Pleasant appearance, variety of colors is easily matched to the design of the room. The advantage of the composition is increased resistance to corrosion, strength, antibacterial properties.

Coating

Chromium applied to a metal surface. It acquires a beautiful appearance, shine and mirror reflection. The advantages of the material are resistance to corrosion, oxidation, so it is common. The downside is that prints remain on the surface.
Under gold. The case is covered with a yellow alloy that imitates gold. Typical for premium models.
Resistant to oxidation, easy to get dirty, but also easy to clean.
Chrome with granite. The design is characterized by an attractive appearance, materials are used in different parts of the equipment.
Brass. Durable, corrosion-resistant compound with a pleasant appearance, but fingerprints remain.
Copper. Vintage design items are made in retro style. Sometimes it is replaced by bronze, which is much cheaper.

What to ignore

check valve. The detail stops the movement of water in the opposite direction. Actual to install in the presence of counters.
Removable watering can. The add-on is equipped on a flexible hose.
spring spout. The structure is made in a curved spiral with a hose inside. Original appearance and practicality (spout bends in any direction).
bottom valve. The element closes, opens the drain hole, there is no need to mess around with plugs that are lost. The control is carried out by a button on the mixer.
Connecting to a filter. The mixer is connected to the cleaning device. This requires two inlets and a separate faucet for filtered water.
Neon lights. The design includes LED lamps that are placed under the spout. The lighting increases, the original design of the product improves (it looks especially original in combination with onyx). Some models change color depending on the water temperature, acting as a hint to the user.

with shower

Grohe Europlus 33547

Competent design and functionality distinguish the model from a number of similar products. The smooth travel of the lever ensures precise, easy control.

The design feature is a cartridge with ceramic discs. The polished surface is coated with a special Teflon compound, which guarantees precise control and smooth glide.

The design is based on water-saving technologies. A small amount of water is used without loss of pressure.

Characteristics

External coating - chrome.
Mounting type - wall.
Classic spout.
Ceramic shut-off valve.
Consumption - 20 liters per minute.
Mounting holes - 2.
Mixer - joystick.
The composition of the body is brass.
Depth - 184 mm.
Automatic switching of water to bath/shower.

pros

No splash or noise.
Attractive appearance.
The design is characterized by economical water consumption, as pressure regulation is available.
Self-cleaning SpeedClean aerator.
Reverse flow protection.
Wear-resistant outer coating (scratch-resistant, increased hardness).
Simple service.
Resistant to dirt, abrasion.
Quick temperature setting.
Surface burns are excluded.
The innovative water supply guarantees complete silence.
Reliable construction.

Minuses:

High price.
Gets dirty quickly.

Auto

Options include temperature control, water volume, tub filling height. Electronic is controlled by two elements. One turns on the water, changes the degrees, the second adjusts the level and switches the shower mode.

The design is installed on the wall or edge of the font, relevant for steel or. The settings are changed with a light touch of the hand, the luminous ring indicates all changes. Automatic bath filling eliminates the need for process control.

Characteristics

Management is one-handed.
Production material - brass, plastic.
External coating - chrome.
Installation - built-in.
The piping is flexible.
The option to save the desired temperature and filling level of the container is available.
Management - touch / push.
Style is designer.
Mounting holes - 2.
Chrome control display.
The memory includes 3 groups of settings.
Power supply - network.

pros

Attractive design.
Convenient display control.
The model combines modern technology and sophisticated design.
A light press brings up the user menu.
Flexible installation.
The main structure is hidden behind the wall, leaving only the control element visible.
The electronic controller reports the heating status and filling volume.
An indicator light indicates changes to the settings.
Easy access to menu settings.
An interesting feature is considered to be control via Ipad through a special application.
All settings are password protected.

Minuses:

Overpriced.
The package does not include a hose and a watering can.

with short spout

Jacob Delafon Talan E10105RU

Model of the French brand, combines style, European quality, reasonable cost.

Particular attention is paid to the design of the product; smooth, soft lines are characteristic, combined with or products made of natural stone. They repeat the stream of water, merging into a single image.

Two valves are equipped on the sides, regulate the temperature with easy movements.

Characteristics:

The material of manufacture is durable - brass.
Strict classical style.
Control type - two-valve.
Stop valve made of ceramics.
Spout - classic.
Water consumption - 20 liters per minute.
Wall mounting - vertical.
Number of mounting holes - 2.
The depth of the structure is 197.

pros

Chrome plating is durable.
Long service life.
Space saving thanks to the short spout.
Quality casting.
The appearance remains unchanged.
Increased reliability due to metal design.
Environmental friendliness and reliability of manufacturing materials.

Minuses:

The package does not include a shower head.
Manual temperature setting for each use.
High price.

without spout

WasserKRAFT BERKEL 4833

An aerator is installed in the mixer, which reduces water consumption, purifies water from small particles and impurities, which is important for.

The body is made of high quality brass with a nickel-chromium plating. The surface is characterized by a mirror shine, which remains unchanged for a long time.

Inside, the faucet is equipped with a ceramic cartridge that covers 500,000 openings and closings.

Characteristics

Type - built-in.
Spout - non-return valve.
Classic form.
Shut-off ceramic valve.
Working pressure - 1 - 5 bar.
Temperature max 65 degrees.
Complete with mounting kit.
Mounting method - hidden (internal).
Control - thermostat.
Style - hi-tech.
Mounting holes - 2.
The body is brass.

pros

The temperature is constant, without interruption.
The risk of burns is excluded.
Stylish and aesthetic appearance.
Increased strength.
Resistance to mechanical, chemical influences.
The material is characterized by durability, strength.
Precise, comfortable regulation of temperature, water pressure.
Smooth control.
The surface is fade resistant.

Minuses:

High pressure is not set.
Careful maintenance required.

Floor

One of the main criteria for choosing a product is the aesthetic appearance of the system, which this model fully corresponds to. Suitable for freestanding or stone.

The model is made in a classic style, characterized by functionality and convenience.

Characteristics:

The cone of the watering can rotates.
The height of the structure is 89.6 cm.
Built-in aerator for economical consumption.
Reverse fuse.
Automatic bath/shower changeover.
The length of the vertical pipes is 73 cm.
Color options: silver, matte platinum.
Shower type - manual.
Sliding sockets - 9 cm.
The maximum shower flow is 9 liters per minute.
Finishing - chrome.
Fastening - floor.
The cartridge is ceramic.
Shower holder - swivel on the right side.

pros

Optimal choice of pressure: 3 types of jet.
Protection against limestone deposits.
Long hose 1.25 m.
The design includes a towel holder.
There is a special place for storing soap.
The distance between the axes is 15 cm.
Easy installation.
Full set.

Minuses:

High price.
Additional mounting space required.
The shower has to be held by hand.

Thermostatic

Hansgrohe RainBrain 15842000

Unique device with electronic control. The touch panel changes three types of a jet, a hand shower, atomizers, regulates degrees, water consumption.

The main operating element of the mixer is a thermostat that maintains a certain temperature. The user specifies the required value, and the automatic system selects the ratio of cold and hot liquid.

When used, there are no jumps, as the device adjusts the parameters. Pleasant equipment adds lighting settings, an MP3 player, Bluetooth, which will be useful in.

Characteristics

Water mixing is electronic.
Mounting holes - one.
Installation - wall.
Style is hi-tech.
The eyeliner is hard.
Type - built-in.
White color.
Material - brass.

pros

A special temperature fuse limits the temperature when it reaches 40 degrees.
A modern way of control - the touch panel makes setting the state of the water as convenient as possible.
The pre-heat option works with five individual settings that are stored in the equipment's memory.
Convenient rotary temperature control button.
Clear control (large characters).
Excellent appearance.
Possibility of a pause in the shower mode.
Innovative technologies make using the system comfortable.

Minuses:

High price.
The outlet is missing.

Without a soul

Grohe Grohtherm 1000 34155

The model is characterized by simple, clear control. High quality materials guarantee ease of use.

Increased reliability is provided by:

SafeStop - protection against burns,
CoolTouch - cold thermostat surface,
StarLight is a chrome plating technology with an ultra smooth surface,
savings programs.

Characteristics:

The mixer is thermostatic.
The spout is a classically shaped non-return valve.
The valve is ceramic.
Consumption - 20 liters per minute.
Type of installation - wall.
Mounting holes - 2.
The body is brass.
Chrome plated.
Automatic switch to shower.
End caps made of plastic.

pros

Economical water consumption.
Lightweight, smooth handles.
Easy switch to shower.
Holds temperature.
Adequate cost.
Scalding exclusion.
Setting the desired temperature.
Easy installation.

Minuses:

Short spout.
Noise during work. If air is present in the pipe, a squeak is heard.
Degrees of heating slightly do not coincide with the actual temperature.
Tough handle. The pressure is regulated by the left handle.
The hose is close, sometimes it interferes with the flow of the jet.

wall recessed

Lemark Shift LM4322C

The model is intended for home or public use. Mortise products are popular due to hidden plumbing communications. The control panel remains visible.

One lever control. Options include water start, regulation, mixing, flow shutoff.

A special switch - a diverter, is equipped with ceramic plates, so the design is resistant to changes in the flow of water when switching spout, shower modes.

Characteristics:

Mounting type - recessed into the wall.
Mounting holes - 3.
Spout - a classic form.
Style - hi-tech.
Management is mechanical.
Color - chrome.
Spout 170 mm long.
The control element is a ceramic cartridge.
Hot water side on the left.
Shower hose - 2 meters.
Water consumption - 23 liters per minute.
Maximum heating up to 90 degrees.
Management - single-lever.
Type is fixed.

pros

Increased reliability.
Easy installation.
Affordable cost.
Long service life.
Aesthetic appearance.
Withstands strong pressure.
Silent operation.
Soft stroke of the crane.
Complete tightness when the tap is closed.
Protected overhead shower, manual watering can from deposits.
Easy maintenance of the outer surface.

Heavy weight.
Long hose.

built-in board

Jado PerlRand Cristal H3981A4

The model has an aesthetic appearance and excellent quality. Device with a swan on the structure.

The faucet is made in the form of a bird, and the valves on the sides are made of crystal, which gives sophistication and sophistication to the object. It is distinguished by small elaborated elements of valves and spouts.

The design impresses with its original appearance and true German quality. Suitable for exquisite products made of natural stone, wood or.

The mixer is one of the most original models, not typical of the German manufacturer.

Characteristics:

Hidden installation.
Management - two valves.
Installation - on board the bath.
Mounting holes - 5.
The spout is traditional, of the usual structure.
Control type - mechanical.
The eyeliner is flexible.
Color - gold.
Depth - 17.3 cm.

pros

Convenient operation due to separation of mixer parts.
Attractive design style.
Saving space around the bath.
Comfortable operation.

Minuses:

High price.
Limited access to built-in elements in case of breakage.
There is no switch to the shower.

Double valve

IDDIS Classic 27014E1K

The standard model is characterized by simplicity and reliability in use, which is relevant for. The design is represented by two valves and one gander. The first element is responsible for cold water, and the second for hot.

Distinctive criteria - attractive classic design and durability due to the simplicity of the design.

Characteristics

The body is made of brass.
Type - two-way.
Water consumption up to 20 liters per minute.
The eyeliner is hard.
The finish is chrome.
Mounting holes - 2.
Spout - swivel, traditional shape.
Color - silver.
Stainless steel hose.

pros

Rugged construction.
The high spout gives space under the faucet.
Clear installation instructions.
democratic value.
Soft, smooth control.
Stable fasteners.
The hot water handle gets hot.
Wide equipment.

Minuses:

Some noise despite built-in aerator.
There is no automatic switch to the shower.
Regular replacement of rubber gaskets is required.
Handles are difficult to turn with soapy hands.
The filter needs to be cleaned regularly.

with long spout

Teka MF-2 Forum

The exclusive design is combined with the refined interior of the room.

The distinguishing element is the cartridge's ceramic disk, which is durable due to the sintered alloy. The coating is formed by condensation (surface transformation), which makes it stable.

The porous surface is covered with grease, which guarantees smooth movements.

Characteristics:

The cartridge is ceramic.
Pressure regulator - aerator.
The spout is swivel.
Case material – brass.
Color, coating - chrome.
The mixer is single-lever.
The spout is swivel.
The lead is flexible.
Spout - 140 mm high, 227 cm long.
The number of modes is one.
Mounting bracket - one.
Installation - external.
Style is purism.

pros

Special anti-limestone protection against pollution.
The convenient long crane moves easily, softly.
The water temperature is adjusted with one lever.
Increased reliability.
Affordable cost.
The kit includes the necessary mounting materials.
Easy temperature control.
Structural strength.
The surface of the mixer is resistant to detergents.
Stylish appearance.
Fast installation.
Long service life.
Scratch resistant.
Exclusion of corrosion.
Easy cleaning.
Doesn't leave fingerprints.

Minuses:

Over time, leaks from under the rubber valve occur.
Lack of watering can.

For 4 holes

Grohe Allure Brilliant 19787

Increased reliability due to metal structural elements made using special technologies.

Equipment elements are built into the bath or other surface, which is beneficial in terms of space saving.

The set includes the Euphoria Cube hand shower.

Characteristics:

The bend is a rectangle.
Shut-off valve - ceramics.
Classic spout shape.
Mounting is horizontal.
The body is made of brass.
Flexible supply.
Number of mounting holes - 4.
The finish is chrome.
Spout height - 253 mm.
Jet - 198 mm.
The depth of the structure is 198 mm.
The cartridge is ceramic.
Built-in spout holder.
Water consumption - 25 liters per minute for the spout, 8 liters for the shower.
Control type - joystick.

pros

Easy temperature control with one hand.
The design of the faucet includes a complete shower set.
Robust, corrosion resistant housing.
With automatic changeover from bath to shower, the option is quick and easy.
Convenient hose length.
Economical fluid flow is guaranteed by the built-in aerator.
Reverse flow protection.

Minuses:

Complicated installation.
The cost is high.

For bath and sink

Milardo Labrador LABSBL0M10

The universal fixture includes a classic forward-facing gander, a shower hose with a watering can.

The model is used for a washbasin, filling the bath thanks to a rotating long spout. A feature is the low cost of products with good performance in appearance and internal content.

The complete set includes all necessary elements of fastening of a shower set.

Characteristics

Body made of brass.
Chrome finish.
Color - silver.
Management - one lever.
Installation - wall.
Stop valve - ceramic.
Spout - classic.
Mounting holes - 2.
The lead is hard.
Depth - 368 mm.

pros

Convenient joystick control.
Silent operation.
Automatic switching from bath to shower and vice versa.
Long headband adds comfort.
Excellent exterior design.
Affordable cost.
Simple control.
Spout rotates 360 degrees.
Smooth, soft jet thanks to the removable plastic aerator.

Minuses:

Complicated installation.
Sometimes you can hear the movement of water.
No automatic temperature control.
Takes up a lot of space.

single lever

IDDIS Viola VIOSB00I02

Brass is the basis for manufacturing, which is resistant to temperature extremes and withstands increased pressure in pipes. The thickness of the coating exceeds the usual standards.

To control the setting of the water, a light touch of the hand is enough.

Special insulators are mounted in the handle, which will prevent surface heating.

The streamlined shapes of the handle, spout and fixtures give the model elegance and grace.
Characteristics:

The cartridge is ceramic.
Material - stainless steel hose.
Length - 1.5 m.
Watering can mode - 1.
The aerator is equipped with a special mesh for silent operation.
Management - single-lever.
Mounting holes - 2.
Spout - traditional form.
Case material – brass.
Mounting is vertical.

pros

Exclusive look.
Complete set for installation.
The holder of a watering can is regulated.
Corrosion resistance.
Quiet work.
Convenient joystick, does not slip.
Avoid temperature fluctuations.
The unique diverter mechanism guarantees switching with minimal head pressure.

Minuses:

Inconvenient wall mounted shower holder.
Average cost.
Limited number of watering can modes.

Three position

Saneko CM-11.R-300-01

Flush-mounted model with “I-box” control unit. The advantage is easy installation thanks to the universal indoor unit, which represents the unique technology of Italian craftsmen.

The composition of the “I-box” is a one-piece cast brass mounting plate. Three flow positions include overhead, hand shower, classic spout.

Additionally, a tropical rain can is installed (not included in the standard package).

The case is fitted into the wall, the panel and the lever remain visible.

Characteristics:

Diameter - 18 cm.
The supply is an eccentric.
Production material - brass.
External coating - chrome.
Mounting type - hidden.
Lever control.
The shape is a circle.
Color - silver.

pros

Easy regulation of water pressure.
The crane unites quality, modern technologies, the increased reliability.
Simple operation.
Attractive design.
The device occupies a minimum of space.
The elastomer housing guarantees quietness and protection of the inside of the unit.
The equipment is controlled by the manufacturer at several levels.
Easy mode switching.
Functional equipment.

Minuses:

Complicated installation.
High price.
Does not include shower set.

Angular

Bravat Fhillis F556101C-RUS

The model is completed with a complete set for a complete shower system:

aerator,
shower hose,
watering can,
divertor,
switch,
mount.

The device is mounted in special holes in the corner or on the side of the bathroom.

The design is embedded, which frees up free space.

Taking a bath is comfortable, as all the equipment is at hand. Attractive appearance of high-tech components will decorate the bath and the interior of the room. These mixers are especially relevant for.
Characteristics:

Installation - on the corner of the side of the bath.
Management - two-valve.
Traditional spout, 20.5 cm long.
Production material - brass.
The eyeliner is flexible.
Gander height - 77 mm.
The cartridge is ceramic.
Color - chrome.
Rectangular shape.
Style - hi-tech.
Mounting holes - 5.

pros

High quality durable coating.
Easy gander rotation.
Stylish design.
Silent operation.
Comfortable management.
Save space with built-in hardware.
Affordable cost.

Minuses:

There are traces of drops on the surface.
Difficult maintenance of internal elements.

Ball

Vega Grand 91А1725122

The device is attached to special holes in the corner of the bathroom. The design is embedded, which frees up free space. Taking a bath is comfortable, as all the equipment is at hand.

Attractive appearance of high-tech components will decorate the bath and the interior of the room.

The body includes a metal ball with holes. When it moves, cold, hot water opens.

Characteristics:

Three elements include spout, mixer, watering can.
High l-shaped spout.
The eyeliner is flexible.
Universal installation: on the side of the bathtub, on a separate platform or podium.
Mounting holes - 3.
Shower head - 3 positions.
The maximum heating is 85 degrees.
Color - chrome.
Case material – brass.
Pressure – minimum 0.5 bar, maximum 10 bar.
Spout - cascade.
The length of the hose is 2 meters.

pros

The cascade type of the device is distinguished by the original flow of water.
The product is massive, distinguished by the strength and beauty of Italian plumbing.
The spout is made of high quality steel.
Protection of the hose from bending, chafing.
Corrosion resistance.
Convenient regulation of temperature, pressure by means of the control unit.
Easy, comfortable pulling out of the hose from the stand.
The package includes spare parts (shower hose).

Minuses:

Rapid wear of rubber seals.
Sensitive to water quality.
An additional coarse filter is required.
At low pressure, a reducer is required.

with high spout

Vidima Storm В7848АА

Bulgarian brand products are tested for quality. Mixers are made using special technologies from zinc and copper alloy.

Chrome-plated finish resists corrosion and chemical attack.

The appearance is represented by a graceful silver-colored vertical spout with a control lever on the right side.

Characteristics:

Classic swivel spout.
The design is straight forward.
Mounting hole - one.
The lead is flexible.
Installation type - horizontal.
Management - single-lever.
The valve is ceramic.
The resource of opening / closing the tap is 1.5 million cycles.
Cartridge - 47 mm.
Low cost.

pros

The products are simple and reliable.
Comfortable operation.
Improved water mixing quality.
Versatile, sleek look.
Temperature control and economical water consumption.
Built-in aerator
Comfortable, elegant handle.
The surface is easy to clean.
The non-return valve is equipped with a water backflow fuse.

Minuses:

Ease of design.
Lack of shower facilities.

Universal

Grohe Multiform 32708

The difference between the model in saving space and versatility. It combines the functions necessary for a bath, sink and shower. The crane rotates in the right direction.

The external design inspires reliability with a strong construction and massive dimensions.

Classic design: a stylish watering can and a faucet with a long spout that takes up some space.

Characteristics:

The length of the classic spout is 461 mm.
Chrome plated.
Material - brass.
Mounting - wall.
The lead is hard.
Water consumption - 13 liters per minute.
Mounting holes - 2.
Two modes of operation of the watering can.

pros

Rugged construction.
Stable shower hose attachment.
Long service life.
Easy installation. Complete set for installation.
Convenient long spout.
The valve does not shut off the water well when changing the mode.
Comfortable mixing is controlled by a joystick.
Smooth, easy controls.
Clear installation instructions.
Nice design.

Minuses:

Noisy cartridge.
Inconvenient spout attachment.
Weighty watering can.
Complex self-repair.
Fragile flexible hose.

Rating

Grohe Europlus 33547
Viega Multiplex Trio E3 684655
Jacob Delafon Talan E10105RU
WasserKRAFT BERKEL 4833
Dornbracht for Villeroy&Boch Square 25 943 910-00
Hansgrohe RainBrain 15842000
Grohe Grohtherm 1000 34155
Lemark Shift LM4322C
Jado PerlRand Cristal H3981A4
IDDIS Classic 27014E1K
Teka MF-2 Forum
Grohe Allure Brilliant 19787
Milardo Labrador LABSBL0M10
IDDIS Viola VIOSB00I02
Saneko CM-11.R-300-01
Bravat Fhillis F556101C-RUS
Vega Grand 91А1725122
Vidima Storm В7848АА
Grohe Multiform 32708

For 74% of consumers who buy a bath faucet, the horizontal installation of the design plays a decisive role in the choice. Why?

There is no need to spoil the finishing materials - a case of wall mounting.
Repair of the mixer or its complete replacement is carried out in 20 minutes. This advantage of the horizontal faucet mounting technology is particularly attractive when compared to the flush mounting method.
Low cost models. Although designer bathroom faucets from foreign manufacturers will have a high price.

Quick and clean faucet installation without the need for professional help. On the sides of plumbing fixtures, holes are already provided for installing a faucet. All you need is to assemble the spout, connect it to the water supply.
The wide design possibilities of the body of the models allow you to choose a bathroom faucet that will become a true decoration of the room and a bright addition to the interior solution.

Popular among consumers in the first half of 2016 was the horizontal faucet for the washbasin in the bathroom from Lemark model Plus Advance LM1206C.

Types of horizontal faucets?

In the manufacturers' catalogs you can find a decent selection of single-lever and two-valve models. Domestic and imported brands have non-contact and elbow taps. The last two types of mixers differ not only in the mechanism for adjusting the water supply, but also in cost. Market analysis has shown that sensor models are 5-35% more expensive than classic single- or double-arm cranes. Rarely, but there are also portion-pressure spouts. Their control mechanism is presented in the form of a button, by pressing which the user opens the water supply for 10-20 seconds. After this time, the faucet will automatically turn off.

Horizontal mount bath faucets are classified not only by the control mechanism. The main division of cranes is carried out according to their intended purpose:

On a washbasin or sink

Models of the horizontal type of fastening differ in the characteristics of the spout. It is this parameter that determines the usability of the model. Today, taps with a spout from 80 to 150 mm long are offered. In the presence of a shallow and small sink, it is better to use a faucet with a shortened curved spout - less splashing, it is more convenient to wash your hands and wash your face. Straight shapes of short spouts and high curved taps are more comfortable to use with deep and wide sinks. When choosing a mixer, you should pay attention to the height of the product. Models are available from 90 to 200 mm high. Popular model for washbasin Milardo Cadiss CADSB00M01.

On the bidet

87% of models have exactly a horizontal mount on the side of plumbing. Most spouts of this type are single-lever designs, although decent 2-valve options are also found. A feature of sanitary equipment is a rotary aerator, with the help of which the direction of the water flow is performed. The height of the spout is always no more than 80 mm, the length can reach 120 mm, but the height of the structure itself can vary from 80 to 155 mm. A convenient and reliable bidet faucet for horizontal installation, according to consumers, is Grohe Supra 24474 with heat-insulated handles.

To the bath

There are several varieties of taps - a horizontal mixer with or without a shower. Horizontal mounting models are also called built-in - the design is designed so that only functional elements are placed on the side of the plumbing. Faucets of this type in 80% of cases are produced with a short spout. This ensures the convenience of taking a bath and shower - the faucet does not interfere, since there are no protruding structural elements. The shortened spout can have a length of 100 to 160 mm. But there are also models with a spout over 200 mm. The height of the faucet can be up to 240 mm, and the height of the spout ranges from 30 to 190 mm. A convenient faucet, according to buyers, was a model with a shower Jacob Delafon July E16043-4-CP.

Many consumers believe that a horizontal mixer is more convenient to use and practical. Models are suitable for both modern minimalist interior styles and classic ones. The design of the crane can be any, as well as the color scheme.

Functionality of horizontal faucets

Modern horizontal models can be supplemented with:

Elements for adjusting the pressure of the jet.
thermostat. Built-in device that allows you to set the required water temperature. The mixer is connected only to the cold water pipe and is recommended for installation where there is no hot water supply or is unstable.
Water saving aerator.
The ability to adjust the source mode.
Nozzles with massage properties. Such an addition may have a horizontal mixer with a shower or a hygienic watering can.

Some features of cranes with a horizontal type of fastening

Many consumers are convinced that this type of faucet looks rustic. The statement is not true, since manufacturers offer models that look unusual in the interior and at the same time are cheaper than those built into the wall. For example, the Hansgrohe Metris Classic 31313000 is a horizontal recessed rim mount.

The body of sanitary devices is made of:

Chrome plated brass or bronze. Optimum material in terms of durability and resistance to operational loads.
Silumin is a moisture/water resistant alloy of aluminum and silicon. Disadvantage: the material quickly ages.
Plastics. Inexpensive and short-lived models of mixers. A faucet with a shower head made of ABS plastic or reinforced plastic has a shower head.
Nickel alloys.
Ceramics.
Steel.

When buying a faucet with a horizontal type of installation, pay attention to all the characteristics of sanitary equipment: the geometry of the body and the material of its production, the dimensions of the faucet (coordinate with the dimensions of the sink), water consumption and others. This is the only way to choose a comfortable and durable crane.

Buy a bathroom faucet

Buy a bathroom faucet - cheap bathroom faucets are the best

A bathroom is an essential attribute of human life, a faucet is an essential attribute of a bathroom. Choosing a bathroom faucet means giving your room a unique personality.

In our online store you will find a full range of models of the best bathroom faucets and you will be able to choose the model that suits you best.

When it comes to buying a bathroom faucet, there are several important factors to consider.

Bath faucets can be of different designs with different functionality.

The mixer faucet can be of a single design or have two handles for regulating the supply of cold and hot water separately.

The switch for the shower can be made in the form of a rotary knob, installed either directly in front of the "spout" of the mixer, or on its body. There are also models with a shower switch in the form of a spool switch.

A special feature of faucets with a rotary switch is the possibility of an even distribution of the flow between the shower screen and the spout.

The length of the spout affects the comfort of using the faucet in the bathroom. In small bathrooms, it is better to choose a faucet with an elongated spout to be able to use it both directly in the bowl of the bathroom itself and in the washstand adjacent to the bathroom. If your room is spacious enough and the washstand is located at a considerable distance from the bathroom, then there is no need for an elongated spout.

Farming in RusavKINO

Internet shop — smesiteli_dlya_vann

Complete set: eccentrics with noise-absorbing effect, reflectors

Brand: Hansgrohe

Installation method: horizontal

Connection diameter: G1/2

Complete set: Wall-mounted mixer, stainless steel hose. steel, watering can (1 function), spout

Brand: Waterline

poultry farm

The farm was created by Leonty Matveyevich Volkov in 2002.

At first, rabbits were bred, which gave dietary meat. We sewed hats and mittens.

Then, they learned about the unprecedented productivity of quails and chickens, acquired good cages and began to breed birds.

They began to improve the breeds and also began to breed geese, ducks, turkeys, ostriches and peacocks.

A goat appeared with kids.

The neighbor has a cow with good fresh milk.

Recently, two milk pigs have been brought in, which get along well with poultry.

The owner is a retired veterinarian who is passionate about breeding pets.

Children from a nearby school come to our zoo for biology lessons and lessons about getting to know the outside world.

Come and you. Welcome.

We also have an equestrian base where you can ride or lodge your horse with us, and we will take care of it.

Basin faucets

Sink mixers, presented in a wide range in the catalog of our online store, are the most compact types of mixers.

They are designed to equip sinks in the bathrooms of residential premises, as well as for use in the bathrooms of cafes, restaurants, hotels and other public and entertainment establishments. Including this type of product is great for installation on mini-sinks.

Each basin faucet from the world's leading manufacturers is distinguished by high quality, durability and sufficiently wide functionality with minimalistic dimensions. All basin mixers are designed for horizontal installation and are installed directly on the side of the basin.

The product range includes:

Basin faucets with one (more often) or two (less often) ergonomic handles for adjusting the water.

Basin faucets, located perpendicular or at an angle to the plane of attachment.

Basin faucets with water flow limitation, with individual setting of the water temperature limiter, with a built-in filter, which additionally purifies the water significantly and increases the equipment.

Models with a hygienic shower.

Models suitable for working with instantaneous water heaters.

Basin faucet on photocells, with temperature control system.

All plumbing equipment is certified.

Bath mixer range

A huge role in the beautiful and functional design of the bathroom is played by a bath faucet, because the comfort and convenience of such a room as a bathroom depends on how high-quality and reliable the water supply will be. Bath faucet - plumbing, which differs from other faucets in the shape of the spout, as well as the presence of a shower head (although not all models may have it). But the quality of the faucet depends not only on its configuration, but also on the materials from which the faucet is made, on the reliability of the assembly, on the functionality and guarantee of dryness in the bathroom, which the manufacturers promise. In our online store you can buy a variety of bath faucets, as there can be a huge number of types of such products.

Selection of collections of bathroom faucets in the catalog of our online store

First of all, bath faucets are products that are divided into single-lever, two-valve and thermostatic faucets. Single-lever models are the simplest and easiest to manage, two-valve models are the most reliable, and thermostats are the most attractive in terms of design, they automatically regulate the pressure and temperature of the water, therefore they are considered the safest of the above faucets.

Also, recently, many manufacturers have begun to produce cascade mixers, in which water flows in a wide massive jet. Such faucets look original on modern bathtubs equipped with hydromassage and other functional systems.

Order bathroom faucets from various manufacturers at an affordable price

For all bath faucets, the price offered in our catalog is quite low. We were able to implement a special marketing program that allowed us to work directly with manufacturers and buyers, which influenced the pricing policy of our company. We offer mixers of only high quality. Basically, they are made of brass - a reliable and practical material, but the filling in such products can be very diverse (both metal, alloys, and ceramics).

Separately, it is worth mentioning the design of mixers. They can be made in a classic style, they can be gold-plated, silver, chrome or matte. Some models are decorated with rhinestones, others with carved elements - all this gives the bathroom interior a special charm and sophistication.

Bath faucets are a purchase in which there is no need to rush, so we advise you to study our catalog in detail and choose the faucet you like.

Installation and connection of the bath faucet

On the picture:

1 What should be considered when choosing a mixer? Firstly, the installation method: horizontal (on the wall) or vertical (on the sink). In the case of vertical installation, study the washbasin and bath: how many mounting holes it has - one, two, three or four. Measure their diameter, etc. "centre distance" (from the center of one hole to the center of another). Having trouble with measurements? - Purchase faucet models recommended by the manufacturer of bathtubs and sinks for this particular model: quite often such “pairs” are already compiled for your convenience.

2 What is the most common faucet installation method? The vast majority of models on the market are designed for vertical mounting under one mounting hole. The faucet is mounted directly on the sink or on the countertop next to it.

1 of 3

On the picture:

Most models of mixers are designed for vertical installation under one hole.

3 What you need to know about the eyeliner with a vertical installation method? The vast majority of faucets are universal: they can be mounted with any type of piping. The eyeliner can be flexible (easier during installation) or rigid (considered more reliable). Flexible eyeliner is used more often. The rigid one will have to be sawn to length during installation: make sure that the chips do not get inside the tubes and then do not end up between the cartridge plates. Getting rid of it is quite simple: unscrew the aerator from the “nose”, and water will blow sawdust under high pressure.

4 What types of mixers are more popular: with a lever or a valve? It's purely a matter of your taste. A mixer with a lever is easier to control, and two-valve ones allow you to more accurately regulate the temperature of the water.

1 of 3

On the picture:

Two-valve mixers can be mounted on one or on three openings.

5 What mixers are the most reliable? Models with a ceramic cartridge are preferred: it (unlike a disk metal one) is able to withstand hundreds of thousands of switchings. Of course, the manufacturer of the faucet with a ceramic cartridge is important: a well-known brand is a guarantee of durability.

Examples of single lever faucets with ceramic cartridge.

6 How often should the cartridge be replaced? Typically, the manufacturer indicates a service life of at least 5 years. Keep the instructions in order to buy a cartridge of the required article in time for a replacement that you can make yourself.

Price. You can buy a faucet with all the modern features you need for reasonable money, as most manufacturers apply new technologies at once in all price segments of their products.

In the photo: AP8420CR model from the Apell factory.

7 How to evaluate the convenience of the mixer? Twist and touch the lever of the selected mixer, evaluate the smoothness of its movement. Some manufacturers offer models with particularly smooth running and a wide angle of rotation of the lever and spout.

8 What decorative coating is preferable? High quality chrome plated as it stays clean longer. By the way, when installing a mixer with any coating, you should use a tool with sponges without teeth (otherwise there is a high risk of damaging the coating). Or put copper or brass or cardboard strips under the sponges.

1 of 3

On the picture:

Chrome plating of faucets is not only a decorative finish, but also a reliable protection against corrosion.

9 What are the features of the best faucets?

The limiter of the maximum and minimum temperature of the given water. This is convenient for families with children and the elderly. The maximum allowable temperature is usually 38 °C.
Water flow limiter up to 5-7 l/min.(at a typical flow rate of 14 l/min.).
aerator- a nozzle on the spout that mixes water with air. The flow of water becomes softer, the consumption decreases. And the jet seems to be as “full-flowing” as without an aerator.
bottom valve, which rises with a lever on the mixer: the drain plug does not have to be pulled out manually.
Water filter built into the mixer. Supplements, but does not replace the mechanical filter, which is desirable to have on the water pipes.

Categories

Popular