Installation of the hob in the countertop above the drawer. How to install the hob: a master class. Electric hob

This step-by-step instruction on how to cut a hole in a chipboard or MDF countertop for a hob with your own hands. When you do, you probably need to know how to cut holes in chipboard or mdf countertops if you're installing a sink or hob. This task may seem simple, but we can assure you that there are many nuances that need to be taken into account for a good result.

On the one hand, you must carefully follow the contour of the gas stove using a template or follow the instructions indicated on the product. In most cases, there are certain restrictions that you should pay attention to, such as the minimum distance from the stove to the back or both sides, to. Use a large L-shaped square to draw a rectangle on your desktop, otherwise the corners will not be square.

To get an accurate hole, you must use a good saw with the right blade. Therefore, the blade must have teeth oriented downwards, otherwise it will split the surface. Drill initial holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).

Work plan for installing the hob in the countertop

Materials:

countertop;
carpenter's pencil;
insulating tape.

Tools:

Protective gloves, goggles;
Saw or jigsaw;
Roulette, level, square;
C-clamps.

Wear safety goggles when making cuts.
Choose a blade with fine teeth.

Deadline

10 minutes

When installing a gas hob or hob, you must cut holes in the countertop.

Tip: Follow the manufacturer's instructions when cutting a hole in a kitchen countertop if you want to prevent potential problems..

How to cut a hole in the countertop for the hob

Guide line markings

The first step is to define the outline of the slab. In most cases, it should contain instructions on how to do this, but there is a technique in which only the recommended hole sizes are indicated. Place the hob on which is located on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the countertop.

Draw a median on the countertop and mark the cut lines using the manufacturer's instructions.

Marking the countertop for the hole for the stove

As you can see in the picture, you need an L-shaped square, a tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. In addition, the rectangle must be symmetrical.

Tip: Check that the rectangle under the kitchen cabinet where the extractor will be built into is correctly positioned and that there is enough space around it (according to the manufacturer's instructions).

Installing under-counter pads

To get an accurate result, you must place several spacers under the countertop. However, the tabletop must be level.

You must leave about 2 inches of space between the cabinets and the countertop, otherwise the saw blade could damage them.

Making initial holes for drilling

Use a drill with a special drill bit to create initial holes along the corners. It is very important to align the bits correctly, otherwise you may drill out of the contour.

Tip: Make sure you are using good RPM controlled drilling equipment. Set the drill at low speeds and hold the drill with both hands if you want to have good control over it. Repeat the process for each corner of the rectangle.

Passage of the laminated layer

In this image, you should notice that the drill is going through the top layer. Do not apply too much pressure to the drilling equipment or it may slide out of place.

We remove the residues from the process with a vacuum cleaner

Drilling a hole in the countertop with a drill will create a lot of residue, so we recommend that you have someone clean it up as you make the hole.

Tip: Work with great care and attention, as it is important to make holes exactly in the indicated places.

Starting holes for cutting in the worktop

After drilling the corner pilot holes, cuts must be made along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. In this way, you will help prevent chipping of the edges.

Cutting a hole with a jigsaw in a countertop

To make the cuts, we recommend that you use a jigsaw. Choose a blade with downward facing teeth. In addition, the blade must have set teeth. If you have not worked with a jigsaw before, we recommend that you fix the countertop. Make sure the blade goes exactly along the cut lines.

Tip: Clean up chips that form frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.

Finished hole in the countertop for the stove

Last but not least, you need to take care of installing the hob into the countertop yourself. If you followed our advice and read the manufacturer's instructions, the hob should slide easily into the hole. However, if the edges aren't quite straight, you can smooth them out with silicone or caulk.

Tip: Use sandpaper to smooth out the cutting edges.

Installing the hob in the countertop

After that, you just have to install the hob in the countertop, connect it and secure it with the screws that should come with it.

Thank you for reading our step by step guide on how to cut a hole in your countertop and install your hob yourself, we encourage you to check out our other articles. Don't forget to share our projects with your friends using social media widgets.

Thinking about making your own kitchen furniture? Then it's time for you to find out that making it is only half the battle, and the second half of this business is to complete the furniture with all kinds of equipment. These are built-in washing machines and dishwashers, and a sink, and an oven, and, of course, a hob, which will be discussed in this article. Together with the website, we will deal with the question of how to install the hob with our own hands and how to connect it to the home gas pipeline and electrical wiring.

Mounting the hob photo

Installing the hob: marking the installation site

The markup is perhaps the most important stage of work associated with the installation of a do-it-yourself hob, which, oddly enough, has the most nuances. Judge for yourself - the whole appearance of the kitchen depends on how clearly and accurately you can mark, and then cut a hole for the hob. This is just the case in which an error of one centimeter can be irreparable - you always need to remember the cost. Buying a new one is not that cheap. The fact is that the panel itself should fit clearly above the cabinet, and there is practically no margin for width there.
There are two ways to mark the landing hole - you can simply lay it on the tabletop, center it on the eye and circle it with a pencil, or you can go the way of professionals and calculate everything down to the millimeter. Naturally, it is better to choose the second option for resolving the issue, since in this case there is a minimum chance of making a mistake. This is done in the following way.

Now it's up to the small - cut and mount the hob in the hole. We will talk about this further. For those who do not like to read and delve into what is written, we are attaching a video on installing the hob in the countertop.

Installing a gas hob: two ways to cut a hole

You can cut the mounting hole for the hob using three different electric tools - a jigsaw, a drill or a manual milling machine. The most accurate and beautiful cut is obtained when using a manual milling cutter, but you don’t even have to ask about its presence in the home workshop of a person not related to construction. Not everyone has a jigsaw either, but at least it is not very expensive, and you can buy it to carry out these works. Well, almost every economic man has a drill. We’ll start with it, but first I’ll warn you about the quality of the hole obtained with the drill - it can be said to be disgusting. Torn edges are quite difficult to seal, but this must be done, and problems will arise in this regard. In principle, they are solvable, but more on that later.

After the hole is ready, it is imperative to waterproof it - if water or even just moisture gets into the end of the countertop, there is a very high probability that the material from which it is made will swell and the countertop will deteriorate. As a rule, the end face of the cutout is treated with silicone. If you cut a hole with a drill, then it will be quite difficult to do it qualitatively - you have to tinker.

Installing an electric hob: mounting and connection

To make it easier to understand how the hob is installed into the hole in the countertop, we will present it as a sequence of work - so to speak, in the form of a small but understandable instruction for installing the hob.

Basically, everything. In exactly the same way, an electric hob is mounted. The only exception is the absence of a gas hose in it. There may, of course, be other nuances - for example, if we talk about a hob-dependent, here the installation process looks a little different. To begin with, and then the panel, which is connected directly to the oven itself.

Basically, everything. Now judge for yourself whether this work is difficult or not. You can deal with it yourself or, perhaps, contact specialists. In general, based on experience, I can say that most people who are wondering how to install the hob with their own hands do this job easily. In fact, it is not complicated, and all that is needed for the successful completion of the case is to clearly observe all the subtleties and nuances.

If you need to save space in the kitchen, it makes no sense to install a gas stove that takes up quite a lot of space. Moreover, not everyone uses the oven that comes with it, especially with the advent of a large number of microwaves and electric ovens at an affordable price. For the most part, the cooking surface is used directly for cooking. There is no fundamental difference in the installation of gas and electric hobs, only some of the nuances that will be discussed later in the article.

Necessary tools, materials

To install the panel, you do not need any expensive and outlandish tool, nor the passage of special courses. Everything is quite simple, overpowering the process is within the power of any more or less friendly person with hands. During the work you will need:

roulette;
a drill with a drill with a diameter of 8 mm or more to drill a couple of holes into which a jigsaw file will fit;
electric jigsaw (you can also cut it manually, but it will take longer and more tiring);
sealant;
special plasticine, self-adhesive sealant or aluminum tape.

This list includes accessories that will definitely be needed. Also, depending on the type of surface, other materials will be needed, for example, Teflon or tow for winding threads, terminals, electrical tape for contacts. The main thing is to get involved in the battle, and there it will be clear what else is needed.

measurements

The easiest option to markup is to carefully trace the contours of the panel directly on the countertop, ensuring an equal indent from its edges. You can also go the other way:

first transfer to the countertop the contours of the shelf above which it is located;
find the center of the resulting rectangle, mark it on the countertop with a cross and make it the middle of the outline under the stove;
after measuring the dimensions of the plate with a tape measure, give an additional 5 millimeters of allowance on each side to the hole being prepared, the marked cross is the intersection point of the diagonals and the middle of the hole (it is advisable to verify the accuracy of the markup by drawing the diagonals in the image).

pruning

To carry out washed down with a jigsaw, it is necessary to drill holes in the corners of the intended contour with a drill so that the file enters freely into them. It is enough to make two holes located diagonally relative to each other. Two cuts are made from each hole according to the markup. Most clearly, such cuts are made using a manual router, but not everyone has it, so a jigsaw is a more realistic option. Carefully, according to the markings, at medium speeds, slowly lead the jigsaw clearly along the markings, making sure that it does not go to the side. It is strongly recommended to try to perform several cuts on some unnecessary bar.

Important nuance- some advise marking and trimming on the back of the countertop. The problem is that the laminate with which the front side is covered can chip, and the plate will not block the chip. Therefore, it is easier to make markings with a marker on the front side, and drill and cut also with the front side up.

Installation and sealing

After the cut has been made, the edges of the slot are treated with silicone or other sealant to protect against moisture. Along the perimeter of the hole prepared in this way, a sealant, which is usually included with the plate, is glued on the upper side. Then the plate is inserted and aligned along the contour of the hole, after which the fasteners located on the back side are pressed. If the sealant protrudes beyond the edges of the surface, carefully cut off its excess with a knife, trying not to scratch the countertop.

Features of installing a gas and electric panel

Important! According to the safety regulations, when using gas appliances, it is FORBIDDEN to connect gas appliances without authorization, including hobs.

This provision is enshrined in the current legislation. Connection is carried out, as a rule, by employees of Gorgaz, for an appropriate remuneration. You can install the device yourself at your own peril and risk, but you should expect possible sanctions from the organization supplying the gas, up to turning it off and sealing the valve. All installations of gas equipment must be carried out in agreement with the relevant organizations.

If, nevertheless, there was a desire to manage on their own, they act in the following sequence:

a flexible hose is connected to the gas valve through a squeegee or fitting;
a hole is prepared in the furniture for the hose;
the presence of jets for the main connection of the stove is checked, if they are not installed, it is necessary to install them;
the gas supply nut is connected to the stove, and it is obligatory with a sealing ring, the connection angle is usually included in the kit.

Checking the absence of gas leakage is carried out by applying a soap solution to the joints. It should not bubble, if there are bubbles, this indicates a leak, as well as the presence of a characteristic smell of gas.

Installation of an electric hob is carried out strictly according to the scheme given in the instructions. If you have little experience with electrical appliances, you should not experiment, it is better to contact specialists. If the power supply is connected incorrectly, both the device may not work properly, and it may fail, as well as the wiring in the apartment. The power supply is connected before the tiles are installed in the socket prepared in the countertop.

Various models provide options for connecting the wire either to a socket or directly to an electrical panel. Keep in mind that an electric hob consumes a fairly large amount of electricity, and make sure that the wiring meets the requirements for power consumption.

And again a photo-lesson for installation. This time I got my hands on a gas hob from Hansa. Not a bad company, by the way, had many years of experience with the stove of this company (albeit electric) - only pleasant memories.

The design of this panel is quite original - I liked it - separate burners are fixed on the frosted glass ...

Instructions are also included. Here are some pictures of the installation. The first scheme, in my opinion, is rather useless.

The second scheme is of much greater practical importance. We will be guided by her. True, this was not fully done, due to the peculiarities of the kitchen project. But more on that along the way.

We take a joiner's square and transfer these dimensions to the countertop. It was impossible to move the panel to the adjacent box due to the nature of the project, so I just moved it as far as possible from the wall (as a result, instead of the recommended 100 mm, I got 80 mm).

The next step is drilling out the marking angles with an 8 drill and connecting them with straight cuts using an electric jigsaw (it is better to use a file with a reverse tooth - the cuts on the front side are simply exceptional)

Since the panel should go onto the wall of the box, I took out the box itself and made a centimeter cutout on its side wall. By the way, after installing the plate in the tabletop, it turned out that I did it in vain on the left, it is thinner by about 4-5 mm and does not go beyond the thickness of the tabletop. But, guided by previous experience, I did just that in advance.

The instructions do not say anything about the next step, but I always silicone the ends of the chipboard in places where the equipment is tie-in. This case was no exception.

Now we take up the hob itself. We turn it over (trying to make the burners crumble at the same time - they can be removed in advance))) and paste a foamy insulating tape around the perimeter (it is included in the kit)
Now we need the help of a professional, namely a gasman, to make the connection. It is forbidden to do it yourself. But the lesson needs to be completed, so I will put the stove, and then I will take everything apart)).

It remains for us to push the plate into the cut out niche, align it and screw it with special clamps.

The instruction sees this process as follows:

True, the width of the tabletop did not allow to do it as in the diagram, namely, to place one edge of the clamp into the cutout on the plate, and the second on the tabletop ...

But this did not affect the degree of fixation much ... As a result, you should get something like this:

By the way, this hood for the functioning of auto-ignition requires connection to a power outlet.

Installing the hob in the countertop: 6 steps

You can install the hob yourself if you first read the instructions Many years ago, kitchen sets did not represent the possibility of mounting a hob in them. Today, this is a common phenomenon, which saves space in the kitchen, and also makes cooking more convenient and comfortable. Installing the hob in the countertop can be done independently. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the size of the future opening.

Do-it-yourself hob installation

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen sets, which qualitatively affects the interior of the kitchen and its functionality. Inserting the hob does not take much time.

You can read more about the features of electric hobs in the article “3 types of hob”.

First of all, on the countertop, you need to make a markup that will fit the size of the hob.

Next to each side of the niche, you need to drill a hole, the diameter of each should be from 8 to 10 mm. The next step is to cut out the niche and treat it internally with silicone. The tabletop is installed on the lower level of the headset. The inside of the panel is attached with double-sided tape or a little plasticine. The tabletop is covered with silicone.

In order to properly install the hob, you should follow the step-by-step instructions

Step by step installation:

The tabletop is placed on the bottom of the headset. If the walls are uneven, the countertop will need to be trimmed. And if gas pipes pass through it, special holes must be made for them. The countertop should be ready for installation down the kitchen.
Inside the box in which the hob will be installed, it is necessary to make markings. To do this, you can simply make pencil outlines that will help you make further markup.
The tabletop is laid face down, and markings are made on the reverse side for a future tie-in.
In each intended cut, small holes must be made so that you can work with a jigsaw.
Carefully cut out the niche with an electric jigsaw.
You need to make sure that the tabletop does not deviate under its own weight. In the process of cutting, it is better to carefully support it.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone from the outside. This is done in order to create an additional hydro-barrier, since the fasteners may not be pressed against the countertop enough.

The gas hob must be chosen very responsibly, because it should last for many years. After the choice is made, the panel must be installed so that it is convenient and safe to use. You can embed the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can contact a specialist for help.

When installing it yourself, it is important to prepare all the necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work related to gas is unsafe to carry out. It is best to perform the installation together with a wizard or someone who thoroughly knows the entire installation process. One of the most important stages of installation is the choice of hose.

If you need to install a gas hob, it is better to seek help from specialists

Hose Selection Tips:

Check hose for damage. There should not be a single defect on the hose.
The hose must be certified. When buying, you should ask the seller to present all the documents for the goods.
The hose can be corrugated metal or rubber.

When installing the panel, the calculation of dimensions must be given special attention. Sometimes in the kit for the hob you can find a template that you need to use in order to properly saw through the countertop. It is important to remember that water should not get on the surface of the panel. The gas countertop must be placed at a safe distance from furniture and textiles.

How to properly install the hob in the countertop

The built-in electric stove is a very convenient device for installation in the kitchen. It works just as efficiently as a stationary stove, but does not take up as much space. Installing such a panel can be quick and easy, without resorting to the help of specialists. The surface can be combined with an oven, which will make cooking even more convenient.

If the master does not carry out independent repairs for the first time, then installing the hob will not cause difficulties.

Before installing the panel, you need to properly cut a hole in the countertop. To facilitate the installation work, manufacturers indicate the required dimensions in the instructions for the device. Pre-marking greatly simplifies and speeds up the installation process.

Before installing the hob, special markings must be made on the countertop

Installation steps:

On the countertop, you need to make markings that will correspond to the dimensions of the panel.
Using an electric jigsaw, you need to make a cutout in the countertop. To get started, you need to drill a small hole for a jigsaw. The cut will be even if you use a jigsaw file with fine teeth.
The dimensions of the hob must match the cut hole. Sections must be treated with a sealant or nitro-lacquer. Sealing self-adhesive tape can be used for processing.

The electric tabletop is connected, focusing on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to control the activation of the burners and their temperature.

What to look for: fixing the hob to the countertop

The installation process of the hob is simple, but requires careful preparation. First of all, it’s tedious to choose the right hob, check its passport data, prepare the tools and decide on the installation location. The installation of a gas and electric hob is practically the same.

You need to mount the panel on the countertop, in which you need to make the appropriate cutout.

It should be noted that to install the electrical panel, you will also need to install an electrical outlet. For a gas panel, care must be taken to carry out gas communication. The built-in panel must be installed so that the maximum gap between it and the worktop is 1-2 mm.

When installing the hob, special attention will need to be paid to attaching it to the countertop.

What to look for:

Correctly measure the dimensions of the panel and transfer them to the cutout in the countertop.
Cut out the necessary segment in the countertop in order to perform the installation correctly.
Treat the countertop with special materials that will protect it from the effects of external negative factors.
Push the panel into the cutout.

It is important to remember that the mortise panel should not enter the gap with force. If there is a backlash, the location of the countertop must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the countertop will avoid contamination of the panel.

hob seal

The sealing gasket must be attached to the hob. If the panel is removed after some time of use, you will notice that the seal will be covered in dirt and grease. The gasket needs to be replaced from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass seal. The table and cutout can be pretreated with a transparent sealant. Sealant residues must be wiped off or carefully removed with a spatula.

Many prefer to use sealing tape because it is safe and environmentally friendly.

Benefits of sealing tape:

Reliability;
Ease of use;
Environmental friendliness.

Bosch seals are known for their high quality. Just placing a panel is not enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening, and a gap is formed, then the tape and the treatment of the gaps with sealant will help save the situation.

Installing the hob in the countertop (video)

The built-in hob is a convenient device that saves space in the kitchen and provides comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to embed a panel qualitatively only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well treated with sealant to protect the panel from water and dirt. All actions should be phased and coordinated.