Interesting amateur radio designs. Amateur radio circuits. Do-it-yourself power supply from an energy-saving light bulb

You can make the simplest electronic circuits for everyday use with your own hands, even without deep knowledge in electronics. In fact, at the household level, radio is very simple. Knowledge of the elementary laws of electrical engineering (Ohm, Kirchhoff), general principles of operation of semiconductor devices, skills in reading circuits, the ability to work with an electric soldering iron is enough to assemble a simple circuit.

Ham radio workshop

No matter how complex the scheme would have to be, you must have a minimum set of materials and tools in your home workshop:

• Side cutters;
• Tweezers;
• Solder;
• Flux;
• Circuit boards;
• Tester or multimeter;
• Materials and tools for the manufacture of the body of the device.

You should not purchase expensive professional tools and devices to begin with. An expensive soldering station or digital oscilloscope is of little help to a beginner radio amateur. At the beginning of the creative path, the simplest instruments are quite enough, on which you need to hone your experience and skills.

Where to start

Do-it-yourself radio circuits for the home should not exceed the level of complexity that you own, otherwise it will only mean wasted time and materials. With a lack of experience, it is better to limit yourself to the simplest schemes, and as you accumulate skills, improve them, replacing them with more complex ones.

Usually, most of the literature from the field of electronics for beginner radio amateurs gives a classic example of making simple receivers. This is especially true of classical old literature, in which there are not so many fundamental errors in comparison with contemporary literature.

Note! These schemes were designed for the huge power of transmitting radio stations in the past. Today, transmitting centers use less power to transmit and try to get into the shorter wavelength range. Do not waste time trying to make a working radio using the simplest circuit.

Radio circuits for beginners should include a maximum of a couple of active elements - transistors. So it will be easier to understand the operation of the circuit and increase the level of knowledge.

What can be done

What can be done so that it is not difficult and can be used in practice at home? There can be many options:

• apartment call;
• Christmas tree garlands switch;
• Backlight for modding the computer system unit.

Important! Appliances to be powered by household AC power should not be designed unless there is sufficient experience. It is dangerous for life and for others.

Pretty simple circuits have amplifiers for computer speakers, made on specialized integrated circuits. Devices assembled on their basis contain a minimum number of elements and practically do not require adjustment.

You can often find circuits that need elementary alterations, improvements that make it easier to manufacture and configure. But this should be done by an experienced master in order to make the final version more accessible to a beginner.

On what to build

Most of the literature recommends designing simple circuits on circuit boards. At present, this is quite easy. There is a wide variety of circuit boards with different hole patterns and printed tracks.

The principle of installation is that the parts are installed on the board in free places, and then the necessary conclusions are connected to each other by jumpers, as indicated in the circuit diagram.

With due care, such a board can serve as the basis for many circuits. The power of the soldering iron for soldering should not exceed 25 W, then the risk of overheating the radio elements and printed conductors will be minimized.

The solder should be fusible, such as POS-60, and it is best to use pure pine rosin or its solution in ethyl alcohol as a flux.

Highly qualified radio amateurs can design a printed circuit board pattern themselves and execute it on foil material, on which radio elements are then soldered. The design developed in this way will have optimal dimensions.

Design of the finished structure

Looking at the creations of beginners and experienced craftsmen, one can come to the conclusion that the assembly and adjustment of the device is not always the most difficult part of the design process. Sometimes a properly working device remains a set of parts with soldered wires, not closed by any case. At present, you can no longer be puzzled by the manufacture of the case, because on sale you can find all kinds of sets of cases of any configuration and dimensions.

Before you start manufacturing the design you like, you should fully think through all the stages of the work: from the availability of tools and all radio elements to the version of the case. It will be completely uninteresting if in the process of work it turns out that one of the resistors is missing, and there are no replacement options. The work is best done under the guidance of an experienced radio amateur, and, in extreme cases, periodically monitor the manufacturing process at each stage.

Video

Beginner radio amateurs who are interested in independently assembling circuits and repairing various electronic devices are lost in a sea of ​​numerous terms and details. Meanwhile, you can give a number of tips on what knowledge is needed in the first place, what devices to use, how to navigate when choosing circuit elements.

Required knowledge

For radio amateurs it is very important:

• know and understand the basic laws of electrical engineering;
• be able to navigate the schemes;
• clearly define the role of each element in the diagram and represent visually how it looks.

Important! Theoretical knowledge must be constantly reinforced by practice.

Tools and devices

To assemble amateur radio circuits and home-made structures, you must have the following tools:

1. Soldering iron, the power of which must be chosen average - no more than 40 watts. More advanced craftsmen are thinking about purchasing a soldering station;
2. Side cutters. Not too massive tool for working with radio devices;

1. Tin-lead solder exists in the form of a wire.

Important! Among all devices, the main, and often the only one, is a digital multimeter or analog tester, through which you can measure all the main parameters of the circuit.

Before you start assembling simple and interesting do-it-yourself radio circuits, you can practice dismantling old radio equipment. At the same time, a practical skill is formed in soldering work.

1. In ancient televisions with lamps, a quite suitable thing is a supply transformer. It can be used in many DIY radios. For example, to assemble a charger for a car battery or a power supply unit for a sound amplifier. The main thing is to know its technical data;
2. In obsolete radio electronic devices: television equipment, video recorders, conventional tape recorders, there are whole microcircuits ready for use. An example would be an audio amplifier whose circuit is constructed by simply assembling components, without etching on printed circuit boards, etc.;
3. The tone control is also used in finished form. At the same time, the assembled sound amplifier will receive new options: the ability to control the low-frequency and high-frequency ranges, change the balance in stereo speakers;
4. Basically, all devices manufactured by radio amateurs operate on five-, nine- and twelve-volt power supplies. Such power supplies from old equipment will be the most useful.

As cases for circuits, you can use any improvised designs or buy ready-made ones, of different sizes and shapes. Shrouds from non-working devices are often used for new radio homemade products.

A non-working PSU from a computer is very valuable, where it comes from:

• many radio components: transistors, capacitors, diodes, resistances that are useful for assembled devices;
• cooling radiators are an important accessory for high power transistors;
• good wires;
• the hull itself is a great place to place new structures.

Circuit Assembly Methods

1. Hanging installation. Simple soldering of components in accordance with the developed scheme. Soldered nodes can be installed on supporting platforms. The method is suitable for constructing radio circuits from a small number of parts;
2. Mounting on a printed circuit board - a textolite platform on which foil tracks are made as connecting conductors.

The second method is divided into several options:

1. Mechanical. Cutting tracks with a sharp object to exclude contact connections in unnecessary places;
2. Chemical. With the help of varnish or paint on the foil, you need to draw the required scheme. Then immerse in a special composition - a solution of ferric chloride. After processing, a wiring corresponding to the drawing will be obtained, and all areas without varnish will be removed by dissolution;
3. Laser ironing.

What schemes to start with

The classic start for radio amateurs is to make a simple detector receiver. The circuit contains a small number of components, and its assembly will be within the power of everyone. Then you can supplement the device with an audio amplifier using transistors. With the advent of experience and understanding, work with microcircuits begins.

A large number of interesting and very simple radio homemade options with a description of the details, the provision of diagrams are on the RadioKot website. You can, for example, assemble color music, pulsed clock illumination, a stereo transmitter, and much more. There are also useful forums where you can clarify complex issues, chat with experienced craftsmen.

As skills are acquired, interest in assembling complex devices will increase. Radio-electronic homemade products are one of the most exciting activities for people of all ages.

Video

Those who are engaged in radio electronics at home are usually very inquisitive. Amateur radio circuits and homemade products will help you find a new direction in creativity. Perhaps someone will find an original solution to a particular problem. Some homemade products use ready-made devices, connecting them in various ways. For others, you need to completely create the circuit yourself and make the necessary adjustments.

One of the easiest crafts. More suitable for those who are just starting to tinker. If you have an old but working cell phone with a button to turn on the player, you can use it, for example, to make a doorbell to your room. Benefits of this call:

First you need to make sure that the selected phone is capable of producing a sufficiently loud melody, after which it must be completely disassembled. Basically, the parts are fastened with screws or brackets, which are carefully bent. When disassembling, you will need to remember what goes for what, so that later you can reassemble everything.

The player's power button is soldered on the board, and two short wires are soldered instead. These wires are then glued to the board so as not to tear off the solder. The phone is going. It remains to connect the phone to the call button through a two-wire wire.

Homemade for cars

Modern cars are equipped with everything you need. However, there are times when homemade devices are simply necessary. For example, something broke, given to a friend, and the like. Then the ability to create electronics with your own hands at home will be very useful.

The first thing you can intervene in without fear of damaging the car is the battery. If at the right time charging for the battery was not at hand, you can quickly assemble it yourself. This will require:

The transformer from the tube TV is ideal. Therefore, those who are fond of homemade electronics never throw away electrical appliances in the hope that they will someday be needed. Unfortunately, two types of transformers were used: with one and with two coils. To charge the battery at 6 volts, anyone will go, and for 12 volts, only with two.

The wrapping paper of such a transformer shows the winding leads, the voltage for each winding, and the operating current. To power the filaments of electronic lamps, a voltage of 6.3 V with a large current is used. The transformer can be redone by removing unnecessary secondary windings, or left as is. In this case, the primary and secondary windings are connected in series. Each primary is designed for a voltage of 127 V, therefore, by combining them, they get 220 V. The secondary ones are connected in series to get 12.6 V at the output.

Diodes must be capable of withstanding at least 10 A. Each diode requires a heat sink of at least 25 square centimeters. They are connected to a diode bridge. Any electrical insulating plate is suitable for fastening. A 0.5 A fuse is included in the primary circuit, and 10 A in the secondary circuit. The device does not tolerate a short circuit, therefore, when connecting the battery, the polarity must not be confused.

Simple heaters

In the cold season, it may be necessary to warm up the engine. If the car is parked where there is electricity, this problem can be solved with a heat gun. For its manufacture you will need:

• asbestos pipe;
• nichrome wire;
• fan;
• switch.

The diameter of the asbestos pipe is selected according to the size of the fan to be used. The performance of the heater will depend on its power. Pipe length is everyone's preference. You can assemble a heating element and a fan in it, you can only have a heater. When choosing the latter option, you will have to think about how to let the air flow to the heating element. This can be done, for example, by placing all components in a sealed enclosure.

Nichrome wire is also selected by the fan. The more powerful the latter, the larger diameter nichrome can be used. The wire is twisted into a spiral and placed inside the pipe. Bolts are used for fastening, which are inserted into pre-drilled holes in the pipe. The length of the spiral and their number are chosen empirically. It is desirable that the coil does not heat up red-hot when the fan is running.

The choice of fan will determine how much voltage you need to apply to the heater. When using a 220 V electric fan, you will not need to use an additional power source.

The entire heater is connected to the network through a cord with a plug, but it must have its own switch. It can be either just a toggle switch or an automatic one. The second option is more preferable, it allows you to protect the overall network. To do this, the tripping current of the machine must be less than the tripping current of the room machine. A switch is also needed to quickly turn off the heater in case of malfunctions, for example, if the fan does not work. Such a heater has its drawbacks:

• harm to the body from asbestos pipes;
• noise from a running fan;
• the smell of dust falling on a heated coil;
• fire hazard.

Some problems can be solved by applying another homemade product. Instead of an asbestos pipe, you can use a coffee can. So that the spiral does not close on the jar, it is attached to a textolite frame, which is fixed with glue. A cooler is used as a fan. To power it, you will need to assemble another electronic device - a small rectifier.

Homemade products bring to the one who deals with them not only satisfaction, but also benefit. With their help, you can save electricity, for example, by turning off electrical appliances that you forgot to turn off. For this purpose, you can use a time relay.

The easiest way to create a timing element is to use the charge or discharge time of a capacitor through a resistor. Such a chain is included in the base of the transistor. The diagram will require the following details:

• high capacity electrolytic capacitor;
• p-n-p type transistor;
• electromagnetic relay;
• diode;
• variable resistor;
• fixed resistors;
• DC source.

First you need to determine what current will be switched through the relay. If the load is very powerful, you will need a magnetic starter to connect it. The starter coil can be connected via a relay. It is important that the relay contacts can operate freely without sticking. According to the selected relay, a transistor is selected, it is determined with what current and voltage it can work. You can focus on KT973A.

The base of the transistor is connected through a limiting resistor to a capacitor, which, in turn, is connected through a bipolar switch. The free contact of the switch is connected through a resistor to the minus power supply. This is necessary to discharge the capacitor. The resistor acts as a current limiter.

The capacitor itself is connected to the positive bus of the power supply through a variable resistor with a large resistance. By selecting the capacitance of the capacitor and the resistance of the resistor, you can change the delay time interval. The relay coil is shunted by a diode that turns on in the opposite direction. This circuit uses KD 105 B. It closes the circuit when the relay is de-energized, protecting the transistor from breakdown.

The scheme works as follows. In the initial state, the base of the transistor is disconnected from the capacitor, and the transistor is closed. When the switch is turned on, the base is connected to the discharged capacitor, the transistor opens and supplies voltage to the relay. The relay operates, closes its contacts and supplies voltage to the load.

The capacitor begins to charge through a resistor connected to the positive terminal of the power supply. As the capacitor charges, the base voltage begins to rise. At a certain voltage value, the transistor closes, de-energizing the relay. The relay disconnects the load. To make the circuit work again, you need to discharge the capacitor, for this the switch is switched.

Since you have decided to become a self-taught electrician, then for sure after a short period of time you will want to make some useful electrical appliance for your home, car or cottage with your own hands. At the same time, homemade products can be useful not only in everyday life, but also made for sale, for example,. In fact, the process of assembling simple devices at home is not difficult. You just need to be able to read diagrams and use a tool for radio amateurs.

As for the first point, before you start making electronic homemade products with your own hands, you need to learn how to read wiring diagrams. In this case, ours will be a good helper.

Of the tools for beginner electricians, you will need a soldering iron, a set of screwdrivers, pliers and a multimeter. To assemble some popular electrical appliances, you may even need a welding machine, but this is a rare case. By the way, in this section of the site we even talked about the same welding machine.

Special attention should be paid to improvised materials, from which every novice electrician will be able to make elementary electronic homemade products with his own hands. Most often, in the manufacture of simple and useful electrical appliances, old domestic parts are used: transformers, amplifiers, wires, etc. In most cases, it is enough for beginner radio amateurs and electricians to look for all the necessary tools in a garage or a barn in the country.

When everything is ready - the tools are assembled, spare parts are found and minimal knowledge is obtained, you can proceed to the assembly of amateur electronic homemade products at home. This is where our little guide will help you. Each instruction provided includes not only a detailed description of each of the stages of creating electrical appliances, but is also accompanied by photo examples, diagrams, as well as video tutorials that clearly show the entire manufacturing process. If you do not understand some point, you can clarify it under the entry in the comments. Our experts will try to advise you in a timely manner!