Different mechanisms with their own hands. Electronic homemade products for radio amateurs and novice electricians. Blacksmith's forge from a cylinder

Interesting homemade products for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, a country shower, a dryer from improvised materials.

Useful homemade products for giving - do-it-yourself washing

Not everyone has the financial ability to buy a Karcher car. If you can't buy it, why not invent it? Do-it-yourself washing will allow you to do without plumbing, reduce water consumption and thoroughly wash your car, fence, garden path or other items.

Here's what you need for such a homemade to give:

• plastic canister with a capacity of 5–20 l;
• hose connector kit;
• automobile nipple;
• piece of hose;
• silicone sealant;
• sharp knife;
• compressor or car pump;
• irrigation gun.

Take a set of hose nozzles, which includes 2 connectors, a 3/4 threaded fitting, a 1/2 adapter.

Here is the principle of operation of such a homemade product for giving: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.

Fill the container with water, but not to the top. Then screw on the lid and pump air in. This will create pressure, and the water will run well when you start to pull the trigger of the gun. Here's how to assemble such a mini sink.

Carefully cut a hole in the lid with the tip of a knife. It should be slightly smaller than the diameter of the nipple stem. Also cut a circle of the desired diameter at the bottom of the sidewall of the canister.

Insert the nipple into the cap.

Now, helping yourself with the wire, place the coupling in the hole intended for it. Apply silicone sealant to secure the coupling to the canister.

It is necessary to tighten the cover and carry out other work only after the sealant has completely cured. Then you will connect one end of the hose to the water gun and the other to the canister.

Pour water into the container, but not to the top so that there is room for pumping air. But do not pump too hard, so that the canister does not deform and burst under pressure. See how the fitting should be screwed in and the connectors installed.

If everything is done correctly, then when you press the trigger of the water gun, the water will spurt out in a good stream. You can adjust the pressure by twisting the tip of the gun.

In the country, it is hardly possible to do without a shower. Try to make something unusual, but tropical, then you can enjoy even more water treatments.

How to make a rain shower from improvised materials for a summer residence?

If you have only recently acquired a plot and you do not yet have a washing room, then you can take a shower right on the street, enclosing a small area near the fence with a curtain. To make such a rain shower, you will need very few components, these are:

• bracket;
• wire;
• flexible hose;
• metal beer can;
• hose adapter;
• awl;
• nails.

Nail the metal bracket onto the wooden fence to get the fixture at the right height. Screw the adapter to the tip of the hose, fix it on the slot of the beer can. The joint can be treated with a sealant. Using an awl, make many small punctures in the jar.

Tie the top of the hose to the bracket with wire, and attach the other end to a water pipe or pump. When you lower the pump into a barrel of heated water, you will be able to enjoy pleasant water treatments.

You can also make a rain shower head using a disc container. In its center, you need to fix the plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Using an awl, make holes at the top of the lid. Glue all fasteners well with sealant. Such a nozzle is held on the bracket with a thick wire or on a rigid pipe.

If you have a desire to make a rain shower, then you can use plastic pipes for this.

You need to bring water to them, first make a lot of small holes with a soldering iron, and then enjoy the pouring drops. Children really like such water procedures.

But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.

And to make a stationary shower, you must first pour water into a tank or barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water here warms up well, and you can wash yourself plenty. To be able to do this in cooler weather, then it is necessary to provide a heating system in such containers.

Do-it-yourself country shower

Before installing it, you need to make a shower cabin. If possible, you can make it out of wood by placing this small structure on the base. Put in a wooden door or go with a shower curtain like this.

There are also simpler options. If you have oilcloth, then use it.

Another option is to purchase impregnated fabric or use an old awning or tent.

If you made a fence from corrugated board and you still have materials, then try to make a shower for giving from them. Metal pipes need to be dug in according to the markup, poured with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become the roof.

If you don't have enough wood planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for it will cost almost free.

When the shower is ready, you can install a water tank on it. To make it warm up better, you can make a kind of metal or hose coil. Then the water will warm up more actively.

These and other homemade products for giving allow you to make the most of the available containers.

To be able to get warm water even when it is not heated by the sun, use electric heating. To do this, you can position the plastic barrel vertically or horizontally. Then it will be necessary to mount the ten on one side, and on the other? water inlet fitting. Make an overflow hole so that excess liquid flows out, and you can see that the container is already full.

Now it remains to install the tank. Usually, a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a soul canister from a metal or iron barrel. If you need to heat the water, then a heating element is mounted in the barrel.

Check out other examples of what you can do in your backyard with your own hands.

Interesting homemade products for giving with your own hands

Garden tools are very necessary for working on the ground. Often in the store they sell not very high-quality sets. After a short use, the handle of the shovel breaks off, or the teeth of the chopper are bent. Therefore, if possible, try to make tools with your own hands.

Take:

• cutting;
• fragment of a water pipe;
• scrap from a two-handed saw;
• screws;
• screws;
• a fragment of a profile pipe with a cross section of 3 cm.

Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut a piece of pipe, unbend the sector, and in the place where the stalk will be, you need to work with a hammer to give the future chopper the desired shape.

To make a blade, take a piece of a two-handed saw and draw the outlines of a future chopper. Punch two holes.

At the same distance and the same diameter, you need to make 2 holes on the chopper itself, and then cut out a fragment from a two-handed saw.

Drill these holes with a drill and a drill designed for metal work. Connect these two parts with rivets, which are screws.

Now drill a hole in the top of the chopper to attach the handle here.

Make also a scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to get a very durable set of tools.

Saw off the desired piece of the handle with a grinder and begin to unbend its part with a chisel.

Then, helping yourself with lever tools, straighten this part almost completely.

It remains to work with a hammer so that the scoop blade acquires the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.

Using an abrasive wheel, clean the edges of the shovel and make them more even. Now process the tool with an emery petal wheel. That's how shiny this shovel will become.

Also drill a hole in it for the handle, then insert it and secure with a screw.

Cover the cuttings of both tools with an antiseptic, and then with varnish. Now you can use the tools for their intended purpose. If you want, follow the same principle to make a cultivator for beds.

It is very exciting to create such things for giving with your own hands. Maybe after you make the tools, you want to make a device on which you can dry part of the harvest. See how one gardener did it.

How to make a dryer for fruits and vegetables?

See what materials you need to take for this:

• sheet metal;
• square pipes;
• locking mechanism;
• polycarbonate sheet;
• self-tapping screws, screws;
• 2 door hinges.

But what tools you need to arm yourself with:

• grinder;
• welding machine;
• drill;
• stationery knife;
• tape measure and marker;
• scissors for metal;
• hacksaw.

First you need to make the basis for the drying cabinet. Make a frame from square pipes. Horizontal and vertical posts are sawn off so that the edges are even. And the ends on the connecting elements should be beveled.

The door here will be metal. To make it, cut 4 fragments from an iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal, using screws with nuts and self-tapping screws. If possible, weld a steel sheet. To make a mount for baking sheets, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 wooden blocks for 4 baking sheets.

An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it dries, put this blank on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, in extreme cases, steel. These materials conduct heat well.

Now you need to sheathe the dryer from the outside, make the roof transparent, made of polycarbonate. Then the sun's rays will penetrate well here. You can also use glass. Cover the ventilation windows with mosquito nets to keep insects out.

Attach hinges and a locking mechanism to the door. Fasten the door in place. See what a wonderful beautiful and roomy dryer turned out.

It remains to make the opposites. They must be breathable. First, knock together the frames from the bars, and then attach a metal mesh to them.

Now you can cut fruit and watch how your device will work. Put a thermometer in the dryer to monitor the temperature. It should be in the range of 50-55°C. At lower temperatures, cover the lower openings by placing a rag here.

In such a home-made dryer, you can dry not only fruits, but also vegetables, herbs, fish, meat, roots.

If this diagram of the device of such a device seemed complicated to you, then you can make a dryer from a metal barrel. A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.

So that water does not flow here and there is better ventilation, such a roof is installed on top.

You can upgrade this fixture with a fan and an electric heater inside.

If you want to make a lawn mower with your own hands, then this is also possible.

Turn an old washing machine into it, for example, like this one.

And if you still have an old bedside table, then you will make a platform out of it for a future almost self-propelled device. But you only need a door from the nightstand.

Drill holes in the center of the motor shaft. Make a cutting knife from an old two-handed saw. It is necessary to saw off from it to the size of the desired shape, cut a recess inside.

Attach two wooden pickets that will become the handles of the mower. Do not forget to fix the motor and extension cord to it. Now you can experience such an interesting unit.

If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.

A lot of interesting ideas are waiting for you in the first video.

And you can get acquainted with cool homemade products from plastic pipes if you watch the second story.

Nothing brings joy to the house like a thing created by oneself. Indeed, various homemade products for the home not only fill life with bright colors, but also give the interior a uniqueness and some kind of zest. And it is certainly impossible to forget about such a thing (even if it is a small trinket). And it’s not so important that these are homemade wood products for the home, paper or plasticine. There are millions of options and methods for making various gizmos, and today we will consider a few of them. So, how to make interesting homemade crafts for the home?

Shelf of tin cans

It would seem that such a trifle - a jar of coffee. However, even from it you can make a beautiful, convenient and useful shelf for storing household items. Often, various souvenirs and memorable photographs are stored in such containers. There is little practical use for this homemade product, but such jars look very harmonious.

Details on how to make this craft

1. First, holes are punched in jars with a drill or with a special ripper (in the upper and lower - 3 each, and in the walls of all the others - 2 points each).

2. Next, the jars are fastened together. Small nuts and screws are used as fasteners. By the way, to get the desired (beautiful) result, you will need to have at least 5-6 of these jars.

3. After that, a hole for the screws is punched in the containers. In the bottom of the jars located in the upper part of the structure, 1-2 holes are made to attach the shelf to the wall. The finished homemade is screwed with a screwdriver or screwdriver. For this, dowels are driven into the wall first.

Everything, now homemade products for the home are being put into action. Be sure - various trifles in such jars will definitely not get lost. Thus, you kill two birds with one stone - decorate the interior and get rid of the mess in the house.

DIY for home - how to make a clock on a CD / DVD?

A clock on a CD is also a very interesting and original option for interior decoration.

As you can see, the design of this device is very original, and therefore it will look organically against the background of any interior (perhaps it will become its highlight). Such "smart" homemade products for the home are made in a matter of minutes. We will tell you more about all the stages below.

So, how to make a homemade clock with your own hands? To begin with, you will need to prepare the appropriate materials - a CD / DVD CD (you choose the design of its front part at your discretion) and a cover-case for it (the distance between the walls should be at least 0.05 centimeters). It is very important that the last part does not have any chips or scratches. To facilitate the work, you can purchase a ready-made watch and then simply replace the standard dial.

It must be arrow, otherwise it will not work to make a homemade product. You should also make numbers. There should be twelve of them in total. It can be cardboard, paper or plastic circles. Their thickness should not exceed two millimeters. Rhinestones can be used as decorations. You also need to prepare about 30-40 centimeters of wire, a piece of leather or fabric and Moment-type superglue. The basis of this whole structure will be a CD-ROM. We will remake it in the first place.

First you need to mark the disk into twelve equal parts and stick numbers on the marked points. In this case, the sectors should not go beyond the outer diameter of the device. How are homemade products made for the home? After the sectors, we proceed to the clock itself - remove the arrows and place them exactly in the center of our disk. By the way, before fixing them, you can stick some interesting photo on the disk, which will make the design of the watch even more original.

To increase the size of the arrows, use thin metal strips. To achieve the desired result, it is enough to apply glue to them and carefully position the part evenly over the entire surface of the leading elements. The very same mechanism of the arrows is attached to the reverse side of the disc.

What to do next?

So, the base of the clock is almost ready. The next step is to make holes in the device along the contour of the arrow mechanism. The box of this disc is installed in a case. The mechanism itself is brought out through the hole and tightly closed. Now, with the help of a wire, an emphasis is made, which is glued to the back cover. To make it more durable, glue a piece of fabric or leather on top of it. This will make the emphasis not only strong, but also beautiful, since the excess part of the wire no longer gapes on the clock as before. Everything, a homemade watch from a CD is successfully made. It remains only to insert an AA battery and set the time. By the way, you can also make a battery with your own hands.

How to make a source of energy from a lemon?

As we know, this fruit contains a lot of acid, respectively, with the right actions, a lemon can be turned into a real mini-battery.

Of course, the charge from such a “battery” is not enough for the operation of household appliances, however, this current is quite enough for the functioning or charging of a mobile phone.

We make homemade products for the home - preparing tools to turn a lemon into a source of constant energy

During the work, you will need tools such as a knife, a soldering iron, a drill, an iron pin, as well as several pieces of copper wire in insulation. Among other items, it should be noted the need for one glass or glass, a pair of wooden sticks and the same number of push pins. And, of course, the lemon will be our main source of energy. You can also use an orange, but there is much less acid in it, so the charge from it will be minimal.

Instruction

First, cut the lemon in half. This is necessary so that he gives more acid, which is necessary for the lemon to be fixed in the glass so that it does not roll around the table. Further, copper and iron pins are inserted into its pulp around the entire perimeter at a distance of 0.5-1 centimeter. "Minus" we will have iron, and "plus" - copper.

Pieces of wire are attached to all pins with a soldering iron. They will act as a connector for the power supply. All elements are connected in series.

At the final stage, sticks are inserted into the battery compartment. Polarity is important here. Contacts are pressed against the contact group. The container remains open throughout the entire process of charging the device.

So, we figured out how to make useful homemade crafts for the home with our own hands. Good luck in your endeavors!

Since you have decided to become a self-taught electrician, then for sure after a short period of time you will want to make some useful electrical appliance for your home, car or cottage with your own hands. At the same time, homemade products can be useful not only in everyday life, but also made for sale, for example,. In fact, the process of assembling simple devices at home is not difficult. You just need to be able to read diagrams and use a tool for radio amateurs.

As for the first point, before you start making electronic homemade products with your own hands, you need to learn how to read wiring diagrams. In this case, ours will be a good helper.

Of the tools for beginner electricians, you will need a soldering iron, a set of screwdrivers, pliers and a multimeter. To assemble some popular electrical appliances, you may even need a welding machine, but this is a rare case. By the way, in this section of the site we even talked about the same welding machine.

Special attention should be paid to improvised materials, from which every novice electrician will be able to make elementary electronic homemade products with his own hands. Most often, in the manufacture of simple and useful electrical appliances, old domestic parts are used: transformers, amplifiers, wires, etc. In most cases, it is enough for beginner radio amateurs and electricians to look for all the necessary tools in a garage or a barn in the country.

When everything is ready - the tools are assembled, spare parts are found and minimal knowledge is obtained, you can proceed to the assembly of amateur electronic homemade products at home. This is where our little guide will help you. Each instruction provided includes not only a detailed description of each of the stages of creating electrical appliances, but is also accompanied by photo examples, diagrams, as well as video tutorials that clearly show the entire manufacturing process. If you do not understand some point, you can clarify it under the entry in the comments. Our experts will try to advise you in a timely manner!