Roofing works - soft, built-up and membrane roofing. Technonikol flat roof slope Technonikol flat roof slope

TECHNONICOL CARBON PROF SLOPE (wedge) is a set of slabs with a slope of 1.7% (slabs A and B), 3.4% (slabs J and K) and 8.3% (slab M), cut from extruded polystyrene foam with a thickness of 40 mm, 80 mm, 70 mm. Used to organize slopes on the roof.

Application area

• Slope device on the roof, increasing the slope or changing the direction of water flow;
• Deceleration device in the valley to the water intake funnels;
• Creation of slopes (groove) at ventilation shafts and skylights;
• Creating an additional slope to divert water from the parapet (counter slope).

Existing problems of the absence of slopes on the roof

• The life of any roof can be significantly increased by creating optimal slopes. One of the main reasons for the reduction in the service life of roofing is due to the formation of stagnant zones (puddles) on the roof surface. This problem is associated with a violation or incorrect installation of slopes and counterslopes on the roof. Repeated and periodic processes of freezing-thawing of water in stagnant zones lead to premature failure of the waterproofing coating.
• Formation of a vegetative layer in stagnant zones.
  The stagnant zones create ideal conditions for the emergence of a vegetative layer: seeds dispersed through the air settle under favorable conditions in the stagnant zones. This leads to damage by plant roots to the main waterproofing coating and, consequently, to premature failure of the entire roof structure.
• Problems of traditional solutions.

As traditional solutions for creating slopes and counterslopes, cheap filling heaters (expanded clay, perlite) or lightweight concrete mixtures (expanded polystyrene concrete, expanded clay concrete, perlite concrete) are used.

The use of bulk insulation is associated with the problem of their displacement, and, consequently, a violation of the design slopes. In addition, sufficiently large granules of filling insulation (20 mm) do not allow a smooth increase in slope. The use of light concrete mixtures leads to additional loads on the base, an increase in deflections of the supporting structure, and an increase in the cost of the entire roofing system. In roofs with a concrete load-bearing base, the installation of slopes by traditional methods involves the use of wet processes (expanded clay pouring with cement laitance, slope installation of lightweight concrete). All this makes it difficult to carry out work on the reconstruction and installation of the roof at low temperatures.

Also, various slab heaters are used for the slope device on the roof, which are refined with the help of cutting tools (for example, hacksaws, saws, milling cutters) for further use as a slope-forming layer. The performance of these works is associated with large time, financial, labor costs, etc.

CONCLUSION: In order to achieve the required slope, it is necessary to use an inexpensive rigid sloped slab. As the practice of roofing construction shows, the optimal slope on the roof should be at least 1.5%, counterslope - from 3%.

The use of TECHNONICOL CARBON PROF SLOPE boards makes it possible to solve the problems of stagnant zones associated with the installation of a slope on the roof, an increase in the slope or a change in the direction of the water flow, the installation of a slope in the valley to the water intake funnels, the creation of slopes (grooves) at ventilation shafts and skylights, the creation of an additional slope to divert water from the parapet (counterclone).

Using TechnoNICOL systems for creating slopes or counterslopes TECHNONICOL CARBON PROF SLOPE, you get additional benefits:

• Reduction of loads on the base due to the use of low density extruded polystyrene foam boards;
• Absence of "wet" processes in the course of work on the installation of slopes and counterslopes;
• Significant reduction in labor costs for the implementation of slopes;
• Reducing the time of work.

The device of a slope-forming layer of wedge-shaped thermal insulation TECHNONICOL CARBON PROF SLOPE cannot completely replace the main thermal insulation layer required by thermal engineering calculation, due to the variability of the layer thickness, despite the fact that it is made from a highly effective thermal insulation material.

The use of a wedge-shaped thermal insulation ramp has an undeniable advantage - it speeds up and simplifies the installation of the roof, even in winter. The use of a combined flat slate screed and wedge-shaped thermal insulation eliminates "wet" processes from the production cycle, as well as the time spent on drying and curing the screeds. Extruded polystyrene foam insulation has a closed-porous structure and is not afraid of moisture during roof assembly. This simplifies its storage on the roof and its use, which is especially important in the conditions of Russian construction sites.

Basic physical and mechanical characteristics

XPS TECHNONICOL	Test method	CARBON PROF SLOPE
		Element A (1.7%)	Element B (1.7%)	Element J (3.4%)	Element K (3.4%)	Element M (8.3%)	CARBON PROF 250 (Additional plate)
Compressive strength at 10% linear deformation, not less than, kPa	GOST 17177	250
Thermal conductivity at (25±5)°C, W/(m*K), no more	GOST 7076-99	0,028
Thermal conductivity under operating conditions "A and "B", W / (m * K),	SP 23-101-2004 GOST 7076-99	0,034
Water absorption, %, no more	GOST 15588	0,2
Flammability group	GOST 30244	G4, G3*
Density, kg/m 3 , not less than	GOST 17177	28
Geometric dimensions		BUT	AT	J	To	M
Length, mm		1200	1200	600	600	600	580
Width, mm		600	600	1200	1200	1200	1180
Thickness, mm		from 10 to 30	30 to 50	from 10 to 30	30 to 50	from 10 to 60	40, 50
volume, m3		0,0144	0,0288	0,0144	0,0288	0,0252	0,0288
Operating range, °С	THAT	From -70 to +75

* Under the order.

Packing Details

The boards are packed in UV-stabilized film and shipped on pallets.

Manufacturing jobs

According to the "Guidelines for the design and installation of single-layer roofs made of polymer membranes of the TechnoNICOL Corporation, 3rd edition 2010"

According to the "Guidelines for the design and installation of roofs made of bitumen-polymer materials of the Roofing Company TechnoNIKOL"

Storage

It is allowed to store XPS TECHNONICOL CARBON PROF SLOPE boards under a canopy that protects them from precipitation and sunlight. When stored under a canopy, the slabs should be stacked on pallets, supports or bars.

It is allowed to store XPS TECHNONICOL CARBON PROF SLOPE outdoors in a special package that protects against external atmospheric influences.

Precautionary measures

Keep away from fire. Chemically resistant to gasoline, organic solvents, and bituminous adhesive with a high content of organic solvent.

We are glad to welcome you on the site of the roofing company "Stroy-Alliance"
The main and priority activity of our organization is the high-quality performance of work on the installation and repair of flat roofs. We will reliably carry out the following works:

	Laying gasket and built-up vapor barrier.
	Each type of these plates has its own advantages and disadvantages. Call us and we will offer you the brand of insulation that is right for you.
	We will perform work on creating slopes from expanded clay or using wedge-shaped thermal insulation.
	Installation of cement-sand and prefabricated screeds.
	Reliable brands of roofing waterproofing. No fiberglass as the basis of the rolls. Only fiberglass and polyester. The traditional technology for the repair of soft flat roofs includes the fusing of roofing roll materials using gas burners. This method of installing and repairing flat roofs is intuitive and has been used for over 30 years. The practical experience of performing such work by the specialists of our organization is 17 years. As a roofing we use high-quality materials of the TechnoNikol company.
	Polymer-bitumen grades with a thickness of more than 6 mm (with two-layer laying) The service life of the roll coating is from 15 years. Strict adherence to the technology of work.
	Domestic and imported polymeric membranes. All accessories for installation are available. Three automatic welding machines. Crews with 10 years of experience in PVC membrane roofing.
	Operational visit to the object. Reliable troubleshooting. The roofers of Stroy-Alliance are certified by TechnoNikol.
	We will draw up a commercial offer according to the technical task or defective statement within 1 working day. If necessary, we will calculate the cost at state rates.

In our activities we use only proven technologies and use materials that have passed many years of testing in real operating conditions. In principle, we do not work with materials that have low technical performance and a short service life. We supply the main materials to the object, directly from the manufacturing plants, bypassing intermediaries.
We offer potential Customers various methods of work performance. This also applies to the optimization of grades of materials, and technologies used in the installation of roof structures. We know how to save money without losing quality!

Do you want the repair or installation of a flat roll roof to be carried out with high quality, without violations of technology and in a short time?
Call now or leave a request and our roofers will get down to business!

Benefits of cooperation with Stroy-Alliance

Stroy-Alliance is proud of its team. Due to the fact that we do not have a "staff turnover", over the years of our existence, the company's employees have gained invaluable experience, studied in Russian and foreign companies. All this guarantees that our specialists will prevent errors, take into account every nuance in the work and provide a high-quality product as a result. Stroy-Alliance specialists clearly fulfill their obligations under the contract, so our company is considered a reliable partner. Expensive modern equipment that we use for installation, repair of flat, soft, built-up, bituminous roofing, laying of rolled roofing, roof waterproofing is the advantage of Stroy-Alliance, as this allows us to minimize the time of work without loss of quality.

• More than ten years is our experience with PVC membranes. We provide our services at a wide variety of facilities: shopping malls, warehouse terminals, private homes;
• Installation of membrane roofing is carried out in the shortest possible time (from 500 square meters per day);
• Quick budgeting, preparation of a full package of documents when putting the object into use (acts of acceptance of work performed, acts of hidden work, etc.);
• Installation of a rolled roof made of PVC membranes, repairs, installation of a built-up flat roof are carried out by us throughout the Central Federal District of Russia;
• The work of Stroy-Alliance fully complies with tax legislation (when concluding a work contract, VAT is deducted);
• Installation, repair of a flat roof is carried out using a variety of methods (modern and traditional);
• Departure of a technical specialist is carried out with maximum efficiency and completely free of charge;
• Brands of materials used are agreed with the Customer;
• When providing services, we use the latest foreign equipment;
• Citizens of the Russian Federation work in the brigade.

Leave your roof repair worries on the shoulders of our specialists!

Wedge-shaped thermal insulation TechnoNIKOL- this is the only set of wedge-shaped slabs in Russia that allows you to create slopes and slopes on the roof on a flat base, to increase the slopes during the reconstruction of the roof.

Wedge-shaped thermal insulation Extruded polystyrene foam TechnoNIKOL-Klin solves the problem of the formation of stagnant zones, creating an optimal slope on the roof. The problem of the formation of stagnant zones on the roof leads to a number of negative consequences for roof structures. One of them is the appearance of a vegetative layer on the roof: seeds dispersed through the air settle under favorable conditions and germinate. This leads to damage by plant roots to the main waterproofing coating and, consequently, to premature failure of the entire roof structure. The second problem is associated with repeated and periodic processes of freezing and thawing of atmospheric precipitation in stagnant zones, which also leads to a reduction in the service life of the roofing.

Traditionally, cheap filling heaters (expanded clay, perlite) or lightweight concrete mixes (expanded polystyrene concrete, expanded clay concrete, perlite concrete) were used to create slopes and counter slopes. Both solutions are associated with additional difficulties: the use of bulk insulation is associated with the problem of their displacement, and, consequently, a violation of the design slopes. In addition, sufficiently large granules of filling insulation (20 mm) do not allow a smooth increase in slope. The use of lightweight concrete mixtures leads to additional loads on the base, an increase in deflections of the supporting structure, and an increase in the cost of the entire roofing system. In roofs with a concrete load-bearing base, the installation of slopes by traditional methods involves the use of wet processes (expanded clay pouring with cement laitance, slope installation of lightweight concrete). All this makes it difficult to carry out work on the reconstruction and installation of the roof at low temperatures.

To solve the problem of creating slopes, it is necessary to use an inexpensive rigid slab with a slope. As our practice shows, the optimal slope on the roof is 2%, the counterslope is 4%. Analyzing the needs of the roofing solutions market and many years of experience in their application, TechnoNIKOL Corporation offers a revolutionary solution - ready-made slopes Extruded polystyrene foam TechnoNIKOL-Klin, which represent a set of slabs with a slope of 2% (slabs A and B) and 4% (slabs J and K).

Application of plates TechnoNIKOL-Klin allows you to solve the problems of stagnant zones associated with a slope on the roof, an increase in the slope or a change in the direction of water flow, a slope in the valley to water intake funnels, the creation of slopes (grooves) at ventilation shafts and skylights, the creation of an additional slope to divert water from the parapet ( counterslope).

Using TechnoNIKOL systems for creating slopes or counterslopes TechnoNIKOL-Clean, you get additional benefits:

1. Reduction of loads on the base due to the use of plates made of TechnoNIKOL extruded polystyrene foam of low density (25-35 kg / m 3);

2. The absence of "wet" processes in the process of production of works on the device of slopes and counterslopes;

3. A significant reduction in labor costs for the implementation of slopes;

4. Reducing the time of work.

Installation of a slope-forming layer of wedge-shaped thermal insulation Extruded polystyrene foam TechnoNIKOL-Klin cannot completely replace the main heat-insulating layer required by thermal engineering calculation, due to the inconsistency of the layer thickness, despite the fact that it is made from a highly efficient heat-insulating material.

The use of a wedge-shaped thermal insulation ramp has an undeniable advantage - it speeds up and simplifies the installation of the roof, even in winter. The use of prefabricated flat slate screed and wedge-shaped thermal insulation excludes "wet" processes from the production cycle, as well as the time spent on drying and curing the screeds. Extruded polystyrene foam insulation has a closed-porous structure and is not afraid of moisture during roof assembly, which simplifies its storage on the roof and application, which is especially important in Russian construction sites.

wedge plate Carbon Pro Slope TechnoNIKOL is made of extruded polystyrene foam. The material is used for slope to the water intake funnel in a flat roof. When working, it is required to perform a roof slope scheme, which engineers calculate according to their special calculations. And in order to find out the cost of xps technonicol material, the price is determined according to preliminary engineering calculation indicators.

The indisputable advantage of using the material is the accelerated and simplified installation of the roof at any time. Wedge-shaped thermal insulation in combination with flat slate screed eliminates the "wet" process during production, as well as drying time. Insulation made of extruded polystyrene foam is easily stored on the roof, moisture resistant.

The advantages of the material include: reduction of loads on the base, reduction of time and labor costs in the process of work, the absence of a wet process of work performed when creating slopes, counterslopes.

XPS TECHNONICOL CARBON PROF SLOPE. Packaging, storage.

The boards are packed in UV film and laid on a foam block for easy unloading. The manufacturer recommends storing the product under a protective canopy from the effects of precipitation, sunlight and harmful substances. Slabs under a canopy are carefully placed on stands in pallets. In the open air, you can store products in special packaging that protects against environmental influences.

The use of plates of this type eliminates problems and solves issues in roofing:

• stagnant zone in places of slope on the roof;
• allows you to increase the slope or change the direction of the water flow;
• razuklonka device and a number of other points.

For the required slope, an inexpensive, rigid sloped slab should be used. From the practice of roofing work, the slope on the roof should be optimally from 1.5%, and the counterslope from 3%.

TECHNONICOL XPS	Test method	TECHNONICOL CARBON PROF SLOP
		Element A (1.7%)	Element B (1.7%)	Element J (3.4%)	Element K (3.4%)	Element M (8.3%)	CARBON PROF 250 (Additional plate)
Compressive strength at 10% linear deformation, not less than, kPa
Thermal conductivity at (25±5) 0 C, W/(m*K), no more	GOST 7076-99
Thermal conductivity under operating conditions "A and "B", W / (m * K),	SP 23-101-2004 GOST 7076-99
Water absorption, %, no more
Flammability group
Density, kg/m 3 , not less than