Do-it-yourself cell phone stand. Mobile phone stand - how to do it yourself. DIY mobile phone stand
Mobile communication devices are in every home, they have become almost indispensable for a modern person and perform a lot of functions. Therefore, quite often they need to be kept not in your pocket, but on your desktop, so a smartphone stand is a necessary thing for everyone. There are many ways to make a phone stand, but one of the best options is of course wood, as it, despite its hardness, will not scratch the smartphone and will look good both in the office and at home on the table.
The easiest way to make a DIY phone stand out of wood is to simply make it from a regular plank. The design of such a product is as simple as possible - a groove of the required width is made in the board and the stand is ready. Since the board has a large plane, and after you put the mobile into the slot, it will stand firmly and securely on the table.
The most important thing about this wooden phone stand is the area of the base that will be in contact with the table, it must be large enough to handle the functional load. As a base, such a homemade phone stand can have any wood and can be shaped into any shape. And the manufacturing process itself is limited to the fact that a groove is simply made in the plank with the help of a milling cutter. The groove can be made flat or sloped, depending on the angle at which the device should stand.
When you make a stand for a smartphone with your own hands, it is important to sand it well, especially in the groove area where the mobile will stand. After all, if there are irregularities, then you can scratch the glass, and this will spoil the appearance of your gadget.
Complex design
If you want your mobile device to be always in sight, not lost in documents, and at the same time your table looks beautiful, solid, then the stand should be appropriate. To do this, you can make it not just from a plank, but from several parts. Don't worry, it doesn't require a lot of tools or material either. The most important thing is not to rush and carefully consider the design that your homemade product will have.
A good do-it-yourself smartphone stand, which is suitable not only for any phone, but also for a tablet, and at the same time will be as stable as possible, can be made from two small planks.
The design of such a stand is as simple as possible, two identical rectangular wooden blanks are taken. On the one hand, about a quarter from the edge, a slot is made to the middle of the board. It is important that the slot does not run at a right angle, but obliquely, so that the stand is more stable and has the correct slope of the plane that will support the phone. On both blanks, a slot is made up to half the width of the blank.
For someone who is just starting out, it can be problematic to find the right angle for the slot. But this is not difficult to do, just attach two parts to one another at the planned angle and just make marks on the side of the end. Well, in addition, so that the phone does not slip, you need to make a groove on a horizontal plank, or stick a small bar that will be a stopper.
After all the cuts are ready, it is enough just to sand the stand well so that the bumps do not scratch the phone case, and cover it with tinting or just varnish.
There are many ways to make a phone stand of this design, for example, you can make a curly vertical part of the stand, which will greatly improve its appearance. Forms can be a variety of hand, leaf, animals, and in general everything that you think of, since a tree can be given almost any shape.
How to choose a stand design
There are quite a few ways to make a smartphone stand, but wood options are not only durable, but also beautiful. In addition, they look much nobler than other materials, as a properly selected wooden accessory will decorate any design, regardless of its style.
Therefore, in order for your handmade mobile phone stand to be beautiful and original, try to choose the right design, size and color. Of course, you should not forget about such parameters as functionality and stability, since if a cell phone falls, it can simply be damaged.
You can make a variety of phone accessories at home and you don’t need a special tool for this. In most cases, with due diligence and patience, you can get by with a simple hacksaw, chisel, sandpaper and a piece of plywood. Then just glue your sample from small parts and at home it will also be easy.
Do not be afraid to experiment and fantasize so that the stand you made is unique, and not like everyone else. After all, mass production is organized in such a way that anyone can afford to buy beautiful and seemingly diverse things. But truly bright individuals prefer unique things in a single copy. Such things are not sold in stores, they can only be ordered or made independently. The second option is much better, not only in terms of economy, but also in terms of the manifestation of individuality.
Even if you do not have experience in making any wood crafts, do not be upset, as there is nothing difficult in this. It is enough to carefully plan everything, calculate what tools and materials will be needed, and only after that proceed to the work itself. If something doesn’t work out for you, then you can try again, rarely does anyone manage to do everything right the first time, everyone learns and everyone makes mistakes. But this is the only way to gain experience and learn to do things right.
Have you purchased a modern gadget and now want to make a stand? There are many techniques and methods that you can use to make a phone stand. Stylish little things can not only decorate the interior, but also make using the phone comfortable. In this article, we'll show you how to do it.
The easiest way to make a stand out of cardboard. To do this, cut a sheet of cardboard into several sheets of the same size. Suitable multilayer cardboard with corrugation inside. Glue the sheets with PVA glue. Let the glue dry. Draw a detail drawing on a thick cardboard base. This will be the figured leg for the stand. Using a utility knife, carefully cut the leg along the marks. Cut out another such piece. Cut out a circle from the remnants of a thick base, it will serve as an additional support. Cut a rectangle on the side of the leg. It will be the basis for the holder. Make a rectangle equal to the rectangular hole. Insert the part into the holes. Thus, you will connect the two legs together. Make axes for a circle from wooden rods. Make two holes in the legs and insert the axles there. Before that, put a circle on the rods. Before assembling the stand, it can be painted or pasted over with newspapers.
Mobile phones have become an integral part of our daily life. Even children already use them from the very first grades of school. In order not to leave your gadget just on the table, consider how to make a phone stand from improvised materials.
First option: from binders
Let's figure out how to make a phone stand with your own hands from what is in almost every home. There are quite a few ways. In this master class, we will make it from binders (paper clips).
This model is well suited for widescreen phones. It will turn out to be very convenient and practical, and it will take literally two minutes to create.
To work, you will need binders and a suction cup.
Production order:
- Connect the binder to the suction cup (a towel holder will work too) in the place where the hook is located.
- Attach the back of your phone to this suction cup when you need to put it down and you're done.
The advantage of this type is that you can place the phone in any position, both horizontally and vertically, or at an angle.
Second option: paper
When there are a lot of papers of different colors at hand, the modular origami technique comes to mind. Let's figure out how to make a phone stand out of paper.
To work, you need 24 white checkmarks and 23 pink ones. Check marks are the simplest element of modular origami.
To make modules, do the following:
- The triangular module is made up of rectangles to make them the same size, take an A4 sheet and cut it into 16 or 32 small rectangles.
- Fold the rectangle in half.
- And again in half, then unfold to make a fold line in the middle.
- Bend the edges of the rectangle to this line, and those where the first fold line goes.
- From below you have formed a ledge, bend its corners up to the edge of the first part.
- Now bend the entire remaining lower canvas up to get an even triangle on the back side.
- Fold it in half. And you will see that you have pockets on both sides.
Now let's move on to our question, how to make a phone stand from such modules:
- Fasten white checkmarks in a circle.
- Then place pink ones between each pair. So you get a cone tapering upward.
- Continue assembling the structure to the desired height and you're done.
This method is suitable for those who like to work with paper using the modular origami technique, if you like to cut and paste everything more, then pay attention to the following model.
Third option: from a shampoo bottle
How to make a DIY phone stand from a shampoo bottle? The work will turn out to be very stylish, despite the simple materials, it will look expensive, as if purchased.
Manufacturing progress:
- Choose the right size shampoo bottle.
- Make a line in the middle and cut along it. For convenience, it is better not to do it straight, but to leave a protrusion with a slot on the back side, so that you can not only install the stand on the table, but also hang it on the wall.
- Take beautiful paper with an ornament (you can use wrapping paper), wrap the stand with it and glue it.
- Carefully cut off the excess wrapper around the outline. Your work is ready.
This craft will look great in your home, especially if you choose the right color and pattern for wrapping paper. You can independently come up with a form for such work or make according to the model. This was one of the many ways to make a phone stand.
Fourth option: from popsicle sticks
One of the most original options for making a phone stand is using Eskimo ice cream sticks. To do this, ask friends and relatives in advance not to throw out such sticks.
When you collect enough, they will need to be glued together:
- first make the bottom;
- then the backrest to the height of the phone;
- the side ones will look good when tilted.
You can connect parts not only with glue, but also by gluing a transverse stick for greater strength.
There are many ways to make a phone stand from scrap materials. We have considered only a few of them. It all depends on your mood and imagination. Even from the old Lego constructor, you can make a wonderful option or sew a wonderful wall cover from dense fabric.
Use any idea. Enjoy your creativity!
Try to cut out such a craft. It will certainly appeal to your loved ones by placing it in a conspicuous place, for example, on a shelf. To make this craft, you will need the following:
Sawing tools.
Preparing your desktop
First of all, you need to prepare your table on which you will work. It should not have unnecessary things and every tool should be at hand. Not everyone has their own desktop and probably already thought about creating it. Making a table is not difficult - it is difficult to choose a place for it in the house. The ideal option is a warmed balcony, where you can do crafts at any time. I already wrote about table preparation in a separate article and tried to describe the whole process of its creation in as much detail as possible. If you don't know how to prepare your workplace, then read the following Article. After you have completed the process of creating a table, try to start choosing your future craft.
Choosing quality material
The main material is plywood. Her choice is always difficult. Each of us must have faced such a problem as delamination of plywood from the end part and asked such a question, why such delamination? Well, it's mostly due to low-quality plywood. If you took the jigsaw in your hands not for the first time, then you can pick up plywood from the remnants of the previous craft. If you are new to sawing and you do not have plywood, then buy it at a hardware store. Choosing material for sawing is always difficult. You should always choose plywood carefully, more often look at the defects of the tree (knots, cracks) and draw conclusions. The complexity of choosing plywood lies in the fact that no matter how you miscalculate its flaws and shelf life. For example, you bought plywood, cleaned it, translated the drawing, and suddenly it began to delaminate. Of course, this happened to almost everyone and it is oh so unpleasant. So it is better to pay attention when choosing and choose good plywood. I wrote a special Article, which describes step by step all the principles of choosing plywood.
Stripping plywood
We clean our plywood with sandpaper. As you already know, “Medium-grained” and “Fine-grained” skins are used to clean plywood in sawing. In construction stores, you probably saw skins (sandpaper in a different way), and they are what we need. In the work you will need "Coarse-grained", "Medium-grained" and "Fine-grained" skin. Each of them has its own property, but a completely different coating, in which it is classified. “Coarse-grained” skin is used for processing rough plywood, i.e. which has many defects, chips, as well as cracks.
"Medium-grained" skin is used for processing plywood after "Large" skins and has a slight coating. "Fine-grained" or otherwise "Nulevka". Such sandpaper serves as the final process of stripping plywood. It gives plywood smoothness, and therefore plywood will be pleasant to the touch. Sand the prepared plywood in stages, starting with medium-grained and ending with fine emery. Grind along the layers, not across. A well sanded surface should be even, perfectly smooth, glossy in the light and silky to the touch. How best to prepare plywood for sawing and which sandpaper is better to choose Read here. After stripping, check the plywood for burrs and small bumps. If there are no visible defects, then you can proceed to the process of translating the drawing.
Drawing translation
For me, the translation of a drawing has always been the main process in my work. I will tell you a couple of rules, as well as tips for high-quality translation of the drawing. Many transfer the drawing to plywood not only with a pencil and copy, but also with the help of the Black Tape, glue the drawing with plywood, then wash off the drawing with water and the drawing markings remain on the plywood. In general, there are many ways, but I will talk about the most common method. To transfer the drawing to the prepared plywood, you must use a copy, a ruler, a sharp pencil and a non-writing pen. Fix the drawing in plywood with buttons or just hold it with your left hand. Check if the drawing fits the dimensions. Arrange the drawing of the clock so that the plywood sheet is used as economically as possible. Translate the drawing with a non-writing pen and ruler. You should not rush, because your future craft depends on the drawing.
Drilling holes in pieces
As you have already noticed, there are parts of the grooves in the details that need to be cut from the inside. To cut out such details, it is necessary to drill holes in them using a hand drill or, as in the old fashioned way, make holes with an awl. By the way, the diameter of the hole must be at least 1 mm, otherwise you can damage the elements of the drawing, which, alas, are sometimes difficult to restore. In order not to damage your desktop when drilling holes, you need to place a plank under the workpiece so as not to damage the desktop. Drilling holes alone is always difficult, so ask a friend to help you with your business.
Sawing details
There are many rules for sawing, but you need to be based on the most common ones. First of all, you need to cut out the internal parts, only then along the outer pattern. There is no need to rush when cutting. The main thing is to always keep the jigsaw straight at an angle of 90 degrees when cutting. Cut out the parts along the lines you marked exactly. The movements of the jigsaw should always be smooth up and down. Also, don't forget to watch your posture. Try to avoid bevels and bumps. If you get off the line while sawing, don't worry. Such bevels, irregularities can be removed with flat files or “Coarse-grained” sandpaper.
Rest
When sawing, we often get tired. Often fingers get tired as well as eyes, which are always in suspense. At work, of course, everyone gets tired. In order to reduce the load, you need to do a couple of exercises. Exercises you can see here. Do the exercises several times during the work.
Stripping Details
It is always necessary to clean the details of future crafts carefully. At the very beginning of work, you already cleaned the plywood with sandpaper. Now you have to do a small part of plywood stripping. With a “medium-grained” sandpaper, clean the edges of the parts and the back of the plywood. "Fine-grained" skin is considered the final stage of cleaning parts. Fine sandpaper is better to clean the front of the parts. When processing plywood, take your time. You can also use a rounded file, with which it is convenient to clean the inside of the holes. Try to get the details without burrs and bumps.
Assembly of parts
Assembling the details of our crafts here is not so difficult. In order to carry out the correct assembly of parts, you need to read the following Article, which details all the details of the assembly. After the parts are assembled into one common craft without any problems, then proceed to gluing them.
We glue the parts
It is necessary to glue the parts of the shelf with PVA or titan glue. You don't need to pour a lot of glue. It is better to tie the assembled craft on glue with a strong thread, tighten it and put it to dry. The craft sticks together for about 10-15 minutes.
burning crafts
To decorate our craft with a pattern (for example, along the edges of the craft), you will need an electric burner. Beautifully burn out the pattern can be very difficult. To burn out patterns, you must first draw a pattern with a pencil. You can read how to work with an electric burner and add patterns to a shelf here.
DIY varnishing
If desired, you can transform our craft by coating it with varnish “On Wood”, preferably colorless. Read how best to Varnish crafts. Try to choose a quality varnish. Lacquering is done with a special brush "For glue". Do not hurry. Try not to leave visible streaks and scratches on the craft.
You can make a small phone stand with your own hands from the simplest materials. Our small master class will help you in your work. Handmade items bring warmth and comfort to your home.
Such a funny cat phone stand is easy to make in one evening. To do this, we need fabric from old jeans to finish the cup, denim or any other fabric for the head, paws and tail.
For work you will need:
- Denim fabric (stripes of different colors).
- A piece of bright fabric for a scarf.
- A little synthetic winterizer or cotton wool for paws, tail and head.
- A glass of cotton swabs.
- Bottom cardboard.
- 4 buttons.
- Pencil, scissors, needle.
Let's get to work:
Take a sheet of paper and freehand draw a pattern. It's pretty simple, even if you can't draw. The head can be done like this: circle the bottom of your cup from under the cotton buds and step back a little from the edge. Get the head of a cat. Cut out the paper pattern. On it we will cut:
- Head (with ears) - 2 parts,
- paw-hand - 4 parts,
- paw-leg - 4 parts,
- tail - 2 parts.
We select materials:
Here is a box you need to take for work, it just fits perfectly in size:
Next, we will make bottoms for our stand. This chopstick cup has a bottom diameter of 8 cm. Yours may be different. For the outer bottom, we cut out a larger circle of cardboard, and for the inner bottom, 0.5 cm less than the bottom of the glass from under the sticks. Cut out a circle with a diameter of 7.5 cm from denim. Sweep along the edge with a thread, insert cardboard and tighten the thread. The second circle is 1.5 cm larger, cut out of denim.
For the inside of the stand, we take a suitable fabric measuring 12 cm (glass height + allowances on each side of 2 cm) * 27 cm (circumference + allowances of 1 cm). We sew the fabric along the short side. We cut the allowances in the lower part of the resulting lining in several places. We put the inner lining into the cup, distribute the notched allowances so that there are no large folds. You can drop a little glue so that the lining does not “walk”.
We turn the top allowance on the outside of the stand. We also fix it by dripping glue in a circle. If there is no glue available, use tape. Then we must draw the belly of the cat. For the top and bottom, trimmings from the legs are well suited. Lay out the strips and fasten them with pins.
Sew all the pieces along the short side. We put on our stand everything that we sewed. On top of the cup we sew the lining and the top of the product with a hidden seam. Then we sew a large bottom. Make sure it doesn't protrude beyond the diameter of the glass. If the bottom is large, cut off the excess cardboard.
We put the cat pattern on the fabric from which you decided to sew it. Cut out a pattern from paper and fasten with pins to the fabric. Cut out, adding a 0.5 cm seam allowance.
Embroider the cat's face the way you like. You can sew beads or buttons instead of eyes.
We sew the paws, tail and head, leaving small gaps in the seams for stuffing with padding polyester. We turn out the details of the head, paws, and tail. We stuff the blanks with synthetic winterizer or cotton wool.
Sew paws, head and tail to the stand. The paws are sewn on at the top and fastened with buttons.
Sew pieces of denim on the tail.
We tie a bright bow around the neck of our cat, you can put a sewn mouse or fish in the paws. If you want to give a product, then a souvenir, for example, a smoking pipe.
How to make a cute and original phone stand out of paper, our small master class will tell. The stand can be made from the base: a cardboard ring left over from adhesive tape, an empty round box of chips, salt, coffee, or a cup of cotton buds.
