Do-it-yourself chair for a schoolchild drawings. Do-it-yourself highchair: diagrams, drawings, dimensions. Video #4: Keyed Straight Joint for Plank Board Ratcheting

Do it yourself - ordinary or for feeding, is not such a difficult undertaking. Even if you don't have much experience with wood. The basic design is simple, there are a lot of options for the degree of complexity, the work does not require any special tools.

The main thing is to determine how much weight the product must withstand.

The choice of material for is determined by the financial capabilities and skills of the home master. It is much easier to make a seat out of plywood, and if for some reason the blank turns out to be unusable, its duplication will not make a hole in the wallet.

  • Solid wood - beech is considered the best. Its wood is dense, of medium hardness, but it is much easier to process than oak. If the cost of the material is high, then you can use an array of birch or pine. Preference is given to species of deciduous trees.

It is recommended that pine be subjected to a procedure such as deresining before manufacturing. Wood contains quite a lot of resin, this will interfere with work, and in the future may cause resinous dirty spots to appear on the surface.

  • Plywood is a multilayer material made from veneer of deciduous and coniferous trees. Perfect for a highchair, as it is lightweight and very easy to process. With a minimum skill, a plywood chair can be made very beautiful, with slotted carvings. In addition, plywood bends easily, which allows you to make the back curved.
  • Chipboard is the most budget option and the most short-lived. The strength of the material itself is quite sufficient for the loads that children's furniture is subjected to, but the ability to hold fasteners - self-tapping screws, nails, this material is low. As a rule, flat parts are made from chipboard, like a table for feeding or a seat.

The selected material must be present in the following form:

  • bars - 20 * 40 mm on average, or more - up to 50 * 50 mm;
  • boards - 25 mm thick;
  • furniture board, if the material for the seat and backrest is solid wood, or sheets of plywood and chipboard.

The product is best mounted on dowels - wooden bushings. They are inserted into the holes when connecting parts and hold them together. This is the most reliable way. But screws, nails and even metal corners can also be used.

Quite a few hardware stores offer their services for cutting wood materials to size. If you have little experience with wood, it is better to take the help of professionals.

If it is planned not only to assemble parts, but also to complete the manufacture of a wooden children's chair with your own hands, then you will need the following tools:

  • electric jigsaw or wood saw for the manufacture of blanks;
  • screwdriver, if metal fasteners are used;
  • a grinder or sandpaper of varying degrees of graininess - all parts of the children's chair must be sanded and polished to prevent injury;
  • hammer - used to seal the joint;
  • brushes, varnish or water-based paint.

Is your child still very small? Then the following video will help dad create a high chair for him:

Drawings and diagrams

You can always use the ready-made drawing of a children's chair with your own hands, found on the construction site. The best in such cases are the sketches presented on the forums. First, they contain the maximum possible amount of information. Secondly, the questions asked on the forums and the answers received on them can clarify many of the difficulties that arose along the way.

Before proceeding with manufacturing, you need to make sure that the dimensions indicated on the drawing fit the child. If not, then the parameters must be increased proportionally, since the stability of the product depends on the correct ratio of height and width.

If it is decided to develop a chair drawing on your own, then it is recommended, after calculations, to make a test model from ordinary building cardboard. Thus, the proportions, height and stability of the model can be checked by the best method - practical.

Children's high chairs - from 0.5 to 6 years, are made according to two main schemes.

  • For feeding - a stationary or folding product, in which there is a table. There is no need to seat a one-year-old baby at a common table: her feeding regimen is completely different, and she still does not know how to eat with everyone. An individual table, taking into account the height and weight of the baby, is a much better option.
  • An ordinary chair - that is, the one that is necessary for studying at the table and for playing. Its shape is similar to that of an adult chair, but execution may vary.

Traditionally, this is a frame with four legs, a seat and a backrest. However, for children, products from two sidewalls, a seat and a back would be a good option. The first model is usually made of wood, the second - of plywood and chipboard.

Drawings of chairs for children

Drawing 1 Drawing 2 Drawing 3 Drawing 4

Manufacturing process

Furniture production can be divided into 3 stages: material preparation, cutting and assembly of the product. A fourth is also possible - finishing. The sequence is the same in the manufacture of any model, but the work itself will depend on the complexity of the design and the selected material.

The following video will help you make a beautiful and bright highchair:

Preparation and production of parts

Often these stages are carried out in parallel to each other. Not always the material in the store has a sufficiently low degree of moisture - 12-16%. Therefore, it is desirable to dry the wood additionally. Also, any of the wood materials must be acclimatized. Therefore, before starting work, it is recommended to leave wood, plywood or chipboard in the room for at least a day.

Sawing bars, boards and sheet material can be done independently, or to order in the workshop at the store. The standard drawing of a high chair includes the following elements:

  • legs for table and chair - 4 pcs. for each part of the product. The bars are cut to size with an electric jigsaw and must be processed with sandpaper;
  • upper and lower crossbars - 2 pcs. also made from bars;
  • crossbars - 3 pcs. for a chair and 4 for a table. The bars are sawn on a workbench or on a table, holding in a vise. A miter box is used to cut 90 degree corners;
  • rounding - 4 pcs., cut out of the board. In this case, the wood fibers must be perpendicular to the bending angle. Otherwise, the part breaks easily due to internal stress;
  • the table top and seat are cut from a sheet of plywood, wood or chipboard to size.

If the chair is made entirely of plywood or chipboard, then all the details - the sidewalls, the partition connecting them, the seat and back are first drawn on the sheet, and then cut out with a jigsaw.

How to make a children's chair from chipboard will tell the following video:

Product assembly

The best option is a dowel connection. The latter are easy to make yourself from the board. The bushings are rectangular in shape, their edges are sanded.

  • Holes are made under the dowels in the details of the product: first, with a drill of a smaller diameter - up to 6 mm, then with a chisel they are expanded to 8 mm.
  • Parts are attached to the glue - carpentry, PVA and so on. Before the final connection, it is advisable to carry out the installation without glue to make sure that the dowels and holes are at the right level and the angles are respected.
  • For the most durable fastening, they proceed as follows: they put the parts on the dowel, tap with a hammer to fit the elements as tightly as possible, and then fix them in the clamp for a day. The manufacture of the chair will take more time, but its reliability will be much higher.

All parts according to the drawing are connected to dowels by the described method. If we are talking about a plywood chair, then its elements are cut out with spikes and grooves, and connected in the same way - with glue.

Bright children's homemade chair

Chair finishing

  • The easiest way is to open with water-based acrylic varnish. The color and gloss level of the lacquer can be customized.
  • You can paint the product with water-based acrylic paint. Although it is not as stable as the oil composition, it is completely safe.

On the seat, and sometimes on the back, a soft insert is made of foam rubber and a cloth cover. It is better to choose a fabric that is well washed, as it will become dirty quickly.

A small wooden stool will find its use in every home. With such high chairs, children rush with great joy. Sitting on such a stool, it is convenient to peel potatoes and perform other "sedentary" work. However, not many people decide to buy a small stool due to the fact that there is always a more important waste of financial resources. But, almost everyone can make a small wooden chair with their own hands. To make it, you need a jigsaw and a little imagination.

Training.
Parts manufacturing, grinding.

Painting.

Training.
The preparation of the material and the necessary tools plays an important role and saves time in the future. To make a stool we need:
- a hewn board measuring 800x200x25 mm (approximate dimensions, you can proceed from what is available),
- 8 shiny screws (50-60 mm),
- sandpaper,
- electric jigsaw,
- screwdriver or screwdriver
- paint and varnish on wood,
- tape measure, pencil and corner.

You need to start by marking the board. First of all, with the help of a corner, a pencil and a tape measure, we mark a rectangular segment without knots 32-33 cm long. This will be the upper part of our chair. Next, we mark two segments of 23 cm each - these will be the sides. Now it is desirable to give them some curly pattern. You can use any objects that have a circle for this, simply by outlining them with a pencil. But, this method involves an irrational waste of time. After all, you will have to mark the center and other dimensions in each sidewall. Therefore, for the sides it is better to use a pattern previously cut out of thick cardboard or other material. It will allow you to easily and quickly mark a large number of sidewalls. It is enough to attach a pattern and circle with a pencil.

By the way, the use of a figured pattern on the sidewall not only gives them a beautiful look, but also allows you to cut off all unwanted knots.
And immediately mark the jumper. It should have the shape of a trapezoid and have sides of 230 and 220 mm. The width of the jumper is not critical - from 80 to 120 mm.

So, it has a marked board.

Important! Do not draw too thick lines - this affects the evenness of the crop. Yes, and the pencil is not erased so easily.

Using an electric jigsaw, we cut out all our details. Equity is important here. For even trimming of the cut, it is better to lead the tool blade not along the line, but to the side of it.

You can learn how to cut evenly on unnecessary waste. So, cut out all the details.

This will give the product not only a beautiful look, but also hide all possible irregularities in the cut.
Further, all these details are carefully polished with fine sandpaper. It is most rational to carry out this procedure at this stage, since a number of inconveniences may arise when grinding the finished structure. It is convenient to grind even planes by putting sandpaper on a wooden block, or on a manual machine for grouting putty. The main thing is quality, since after painting all the flaws will appear and be visible.
This is what the sanded and unsanded sides look like.

So, it has the same parts, but already ready for assembly.

It is desirable to assemble in the following order:
- we connect the sides with a jumper (1 screw on each side);
- we expose this design on a flat surface and screw the top cover (2 screws on each side);
- We strengthen the connection of the sides with the jumper (1 more screw each).

The chair is assembled! We check it again on a flat plane. If the stool staggers a little, then we trim the legs until the product is completely stable.

Painting.
Before painting, we once again check the product for defects, if necessary, erase them and the remains of the pencil. Using a brush, we clean the stool from wood dust and proceed to painting.
There is already “there is no friend for the taste and color”! You can leave the natural color of the tree by opening it with a colorless varnish. You can give the product a certain color using a variety of wood paints, which are full in all hardware stores. In principle, one layer is enough for painting. But, if, after the first layer has completely dried, the surfaces are again lightly sanded with fine sandpaper and a new layer of varnish is applied, then the gloss of the product will noticeably increase.
Important! Poorly sanded ends absorb more paint and become darker.

It looks like a finished, varnished chair.

Almost every parent faces the problem of purchasing children's furniture. You can make a highchair at home - after all, this will significantly save the family budget, and you yourself will be sure of durability and quality. Making a highchair with your own hands is not difficult, the main thing is to make the right drawings and dimensions, choose the right wood and do not forget about decorating with decorations.

When the child can already sit, eat and play by himself, the standard furniture becomes a little large for him. A baby chair made by yourself becomes a great alternative to store-bought plastic options, because it is non-toxic, more durable and even looks more solid. Their use becomes necessary already in the first year of a baby's life, because he needs to be taught to be independent. Before wondering how to make a children's chair, you need to decide on its model. Today they are of two types:

  • standard chairs;
  • chairs transformers.

Children's chair Children's chair with armrests Transforming chair

Every day the child has more and more new hobbies that require a sitting position. A do-it-yourself wooden chair will definitely appeal to little discoverers. Do not forget about the decor. A self-made chair can be decorated to match the already created interior of the room, or you can make it some kind of zest that is clearly expressed in any room. What you were able to do with your own hands should definitely please the child, because you will put a piece of your love into this work.

Procurement of the necessary materials

A do-it-yourself plywood chair requires certain tools, like any other furniture. Of course, joinery will not be required, but you will have to prepare some fixtures for a wooden chair:

  • a small number of bars, based on the selected chair model, having a cross section of at least 50 by 50 millimeters;
  • bars with a cross section of 25 by 50 millimeters;
  • bars with a cross section of 25 or 25 millimeters;
  • drill, screwdriver;
  • screws and self-tapping screws of various lengths;
  • sandpaper or grinder.

Since the do-it-yourself stool is intended specifically for children, you should take care of the quality of all purchased materials. Wood is generally considered a safe and non-harmful product, so its use does not compromise safety. It is better to use linden wood for the highchair, it lasts much longer than the others. But, such a tree costs a little more. Experts recommend making a children's table out of linden, because it is one of the parts of this furniture that is most exposed to mechanical stress.

Go to work

The first step in creating a chair for a child with your own hands is to create diagrams and drawings. Without this main action, it will not be possible to assemble a quality product. There are a large number of photo and video materials on the Internet, as well as detailed diagrams of various products, which you can navigate when creating your own masterpiece. The main thing is not to get hung up on the templates presented, the options presented should only be samples, especially useful for novice builders.

Preparing parts for a children's stool with your own hands also takes time. The cut parts must be dried well, then deformation will not occur during the work and the high chair made will please its owners for a long time. After drying, the wood must be sanded with high quality, leaving no bumps or splinters. Knowing how to choose high-quality material, there will be much less problems with its preparation.

After the cleaning process is completed, you can begin to assemble the table and chair for the child. You should start connecting the parts of a children's wooden chair from the legs, so you can achieve a more stable position. A do-it-yourself children's table is also assembled in a similar way. After collecting all the parts, you will get a finished version of the design, but do not rush, you still have to work a lot with it.

How to fasten parts with a dowel First, glue the back pair of legs and the crossbar. Next, we connect a pair of front legs. Then we connect hags and crossbars with each other. All gluing points are compressed with clamps, but with the obligatory control of right angles

Decoration and decoration

The last stage of do-it-yourself children's furniture made of wood will be its decoration. You should always start with varnishing. We choose only acrylic options for work, because they are less toxic. Do not forget that a small child will constantly be in contact with his furniture, and therefore breathe the vapors emanating from it. You need to know how to choose a coating product so that the child remains completely safe.

Experts advise doing the coating at least twice, this will emphasize the decor and smooth out possible roughness. Do not limit your imagination! Children's table and chair can be decorated not only with varnish. Add bright prints, match the design of the product to the interior of the child's room and then he will definitely fall in love with his furniture. Do not forget that the decorations should be safe for the baby and if he is still too small, you should not complete the decor with attached small items, because he can tear them off and try.

A plywood chair for a little princess can be decorated with a beautiful cover and lush bows. This will make her room more tender, and the child will want to be creative while sitting on a chair made by loved ones. For boys, decor with painted cars, airplanes or rockets is perfect. If your drawings are not very good, then use the usual stickers. Only after sticking them on the chair, go over the entire surface with another layer of varnish. Then the baby will definitely not be able to tear them off and spoil the original appearance.

We decorate a children's chair (option 1) We decorate a children's chair (option 2) We decorate a children's chair (option 3)
We decorate a children's chair (option 4) We decorate a children's chair (option 5) We decorate a children's chair (option 6)
We decorate a children's chair (option 7) We decorate a children's chair (option 8) We decorate a children's chair (option 9)

You can easily make a children's chair with your own hands, drawings for which are available on the Internet. Your loved ones will be delighted with such an original gift and may be asked to repeat their work. If you work on the selected material, then there will be no problems with manufacturing.

Be sure to follow the drawn drawings and diagrams, then the product will stand exactly, and the child will sit on it in complete safety. Do not forget how to make a highchair, because perhaps these skills will come in handy in your life more than once.

One of the positive things that goes in favor of wooden furniture is that it is possible to make a wooden highchair with your own hands. Naturally, in the case of twins, you will have to make two chairs at once. Note that usually home-made children's highchairs made of wood are different - classic folding, transformers and growing ones.

In this article, in the “for dummies” style, we will tell you how to make a highchair for feeding with your own hands using the example of a wooden transformer highchair. We will show two working options for a do-it-yourself feeding table-chair with drawings and dimensions, and also make some considerations about them.

ATTENTION!!! The article turned out to be long, as we write not only for experienced craftsmen, but also for beginners, as well as people who rarely do anything with their own hands. If you don't want to read everything, use the table of contents. Pop-up heading tips will help you understand what is there, and choose the right one.

If you want to make a high chair with your own hands, but not a transformer, or you know everything how to do it and love brevity, it doesn’t matter either. Over time, a link to the entry will appear at this place, where information about homemade highchairs for feeding will be collected in one heap. In the meantime, we are looking at the site map and the rubric, there are articles there.

The content of the article:

Do-it-yourself highchair - why a children's wooden highchair TRANSFORMER. MOTIVATION

One of the big advantages of children's wooden transformers for feeding is that the design of high chairs is extremely simple, so even a beginner can build them on their own. You can make such a highchair for feeding with your own hands either from improvised materials, or you can easily purchase material at a low price.

In the article do-it-yourself children's highchair, we examined in detail how a folding highchair is made. It turned out that it is done quite simply. But its relevance is very doubtful - wooden furniture is always bulky and heavy, and in two years such a high chair will have to be disassembled into spare parts and made separately for a children's table and chair.

But the chair - transformer immediately "kills" two birds with one stone: it is both a chair and a table - a desk. First, the high chair is used for its intended purpose, together with a small table, and then, after 1.5 years, it is disassembled, and the child gets a separate desk and high chair. Convenient and practical. Perhaps this is precisely what causes constant interest in a wooden highchair transformer for feeding made by oneself.

It remains only to figure out how to make such a miracle of technology on your own. And in the beginning, let's see the video of one of the craftsmen.

Do-it-yourself feeding chair or wooden high chair do-it-yourself transformer for feeding a baby getting started

Searching on the Internet on the topic of a do-it-yourself feeding chair, it will become clear that there are two options for a transforming chair.

The first option is more complicated, but for some reason it is the one that is popular on the Internet. Most likely, once someone made a wooden transformer chair for feeding with their own hands in this way, and then articles on how to make it yourself miraculously mindlessly multiplied. Because where to take the correct option is not clear. We give here the most understandable (for the author) description and sane drawings.

The second version of the do-it-yourself feeding chair is simpler and more logical, it is according to it that factory wooden transformers are made. And we also bring it here, with our own measurements.

If everything is clear with the material and you are only interested in drawings and dimensions for a do-it-yourself high chair, then immediately proceed below to the parts of how to make a do-it-yourself high chair - Option 1, and How to make a do-it-yourself wooden high chair - Option 2. A for now, since we decided to write a story in the “for dummies” style, let’s talk about the materials used.

DIY high chair - Materials

To make a highchair for feeding with your own hands, you will need wooden blocks. A board with a thickness equal to the thickness of the bar used can be added. Plywood or chipboard, self-tapping screws, glue, fabric washable upholstery and any soft filler. Well, more staples for a construction (furniture) stapler.

You can use any timber that is sold or available. It would be better if he was trimmed. So with him less fuss. Otherwise, you will have to plan it yourself and make it smooth. It is most convenient to take the size of the beam 20x30 mm.

Chipboard or thick plywood - from 10 to 15 mm thick - will be used as a table top for a desk table and a small removable table for a high chair.

The hard parts of the back and seat of the do-it-yourself feeding chair can be made from fiberboard or plywood. It is not necessary to use thick plywood, from 5 to 10 mm thick is enough. In general, plywood will be stronger, but stapler staples are easier to enter into fiberboard.

Some parts are glued together. To do this, you can use wood glue or just PVA glue.

To make a soft back and seat on a high chair with your own hands, you will need an external upholstery - a durable, easy-to-wash fabric, such as raincoat fabric or bologna, or just oilcloth, and inside a soft filler - foam rubber, batting, synthetic winterizer or something else. See for yourself how much you need. Soft filler can be glued to the hard parts of the back and seat, or simply fastened with a construction stapler, or you can combine both options. Upholstery is easier to immediately fasten with a stapler. So it will be more reliable. The size of the staple depends on the stapler and the chosen thickness of the upholstery.

It's also a good idea to have a medium sandpaper to sand the parts and make them smooth.

In the first version of the do-it-yourself highchair, only 4 wood screws are used: for attaching the tabletop to the desk-table. All other wooden parts will be interconnected with homemade dowels, also made of wood. You can put the rest of the bars on the dowels.

In the second version of the do-it-yourself feeding chair, there are practically no dowels, but there are many self-tapping screws for fastening all the parts together. Factory transformers are made on euro self-tapping screws, and a do-it-yourself wooden highchair transformer for feeding can be assembled on any. The main thing is to assemble correctly. Dowels are used only if you decide to make rounded parts that are conveniently attached to the bars with their help.

Both the wooden table and the do-it-yourself feeding chair have rounded elements, although you can do without them. These elements can be made either from a board with a thickness corresponding to the thickness of the bar used. If the beam is taken, as here, 20x30 mm, then we take a board 20 mm thick, but 30 mm is also possible, this depends on how you put the bars, joke F). If there is no board, then the same bars are perfect. You just need to glue them together.

Depending on how much and how you arrange the rounded elements for cutting on the board or glued bars, this is the length of them (boards, bars) and you need to take. On glued bars or a board, 4 elements must be laid at once. Therefore, the length will be from 0.5 to 1 m, and maybe 2 m is not enough.

Do-it-yourself feeding chair - separate words about wood and paintwork

I propose to pay attention to the wood material of the high chair. We note right away that a children's wooden chair for feeding with their own hands is best made from linden. However, like any other children's furniture for kids. Since conifers often used in the manufacture of wooden furniture may not be suitable here: pine emits resin, which is very toxic. And it is better not to risk children's health. However, pine is often found in hardware stores, so we try to take it as dry as possible and without interspersing resin. Believe me, the child will be better, and it will be easier for you to do it yourself.

To give shine, color and environmental protection, it is better to use ACRYLIC varnish, or paint. It is not as harmful to the baby as the rest. Why exactly him? The answer is - what if the baby tries a table or a chair for feeding, which you yourself made with your own hands? You are responsible for the consequences. Although if it doesn’t matter or it’s not possible to get them, then you can cover the feeding chair with your own hands with whatever you want.

Do-it-yourself wooden transformer highchair - Option 1

To understand what a do-it-yourself highchair will be in the form of components of option 1, we present the drawings and dimensions.

To make parts of a children's high chair for feeding a wooden transformer with our own hands, we take a bar with a section, for example, 20x30mm. From it we will make the following details. Specify the length and quantity.

  • Legs - 390 mm, 4 pcs.
  • Rounded parts - 4 pcs.
  • Armrests, they are also the upper crossbars of the chair - 195 mm, 2 pcs.
  • Planks running parallel to the armrests, they are also crossbars, 335 mm, 2 pcs. On these crossbars we will then attach the seat with the crossbars of the feeding chair
  • Planks on which the seat and back are attached, they are also crossbars - 300 mm, 3 pcs. Two for the seat and one for the back
  • Small table on a chair (H x W) 340x340 mm. It lies on the armrests of the chair 340 mm = 300 (length of the chair crossbar) + 20 + 20 mm.
  • The seat and back have the same dimensions (H x W) 250x290 mm. Width 290 mm \u003d 300 (length of the cross bar) - 5 - 5 (gaps on both sides for upholstery and soft filler), mm.

  • Legs 500 mm 4 pcs.
  • Planks for the lower and upper part 410 mm 4 pcs. On the lower slats there is a table for feeding, on the upper slats a tabletop is attached.
  • Cross bars 340 mm 4 pcs. To fasten the sides of the table. Length 340 (mm) = 300 (length of chair crossbar) + 20 + 20 (mm). This is done so that the chair gets up between the sidewalls of the table.
  • Tabletop (H x W) - 440 × 380 mm. 1 PC. The tabletop rests on the upper slats and does not protrude beyond the sidewalls. Width 380 (mm) = 340 (cross bar length) + 20 + 20 (mm). Length 440 (mm) = 410 (top bar length) + 30 mm

How to make a high chair with your own hands

Work begins with a chair. To do this, according to the size, the bars are cut to the desired length. Separately, you need to make rounded parts - they connect the legs and armrests in front and behind. Naturally, all sawn parts must be made smooth, lint-free and treated with sandpaper with special care - small children are always an increased risk of injury. Therefore, to the question of how to make a highchair for feeding with your own hands, we give a pretentious answer - we work conscientiously.

Roundings for a wooden highchair transformer for feeding do-it-yourself are cut out separately - according to the drawing. For rounded parts, there is one IMPORTANT point. If you glue the bars and place the part with wood fibers in a different way than shown in the figure, then such a part may break in the most unexpected way during sawing or further operation. Therefore, the bars must be glued with wood fibers parallel to each other. And you need to place the rounded part of the highchair for feeding with your own hands along these parallels. The same applies to the board - we place the part for sawing parallel to the wood fibers of the board.

To successfully glue the bars, we use wood glue or PVA. Additionally, the bars do not need to be jointed and leveled. At the bars, you need to choose fairly even planes, position them correctly and simply press them harder with clamps. It will dry out in a day for sure.

Then, from the waste bars for the highchair for feeding with your own hands, you can make rectangular panties. Dimensions - 8x20x50 mm. In general, the length of the dowel should be 4-5 mm less than the total depth of the groove of the two fastened parts. The edges of the dowels can be slightly rounded.

On all parts, mark places for planting dowels. To do this, mark the contours of the groove, for example, with a pencil. Rectangular grooves for dowels should be made approximately 30 mm deep. To do this, drill 4-5 holes with a drill with a diameter of 6 mm. Next, using a chisel, align the walls of the groove and fit it to your own, individual, home-made dowel. And if there is a router, then we make the grooves with a router, it’s easier.

When all the details are ready, there are dowels and grooves for fastening, you can start assembling a children's high chair for feeding a wooden transformer with your own hands.

Do-it-yourself wooden highchair transformer for feeding a child - assembly

We begin to assemble a wooden high chair transformer for feeding with our own hands from the sidewalls. First one is done, then the second. On the dowels, draw a line in the middle of the length. Using a light hammer, install to the marked line. Then we take the part to be connected and insert the dowel into it. We connect the parts first dry, i.e. without glue. After all the details of the sidewalls are connected, we check for cracks. If everything is fine, then carefully separate the parts and glue the dowels, and then assemble them again, as indicated above. Then you need to pull off the parts and let dry, about 1 day. You can tighten it with clamps, or tightly wrap it on both sides with a rope. But at the same time, make sure that nothing is warped, and no gaps are obtained. It is less reliable to tighten with a rope than with a clamp, but not everyone has clamps of this size.

While the sides of the transformer highchair for feeding the child are drying, you can do the seat and backrest with your own hands. They are cut out of plywood or fiberboard, according to the drawing. If the plywood is not thick or fiberboard is used, then to give strength it is better to cut out 3 parts of the seat and back and glue them together. Lubricate with glue and clamp with clamps. It also dries overnight.

After the sidewalls, seat and back are assembled and cut out, we assemble everything completely. On the seat and backrest from the planned reverse side of the wooden highchair of the transformer for feeding the child with your own hands, you can immediately attach the crossbar strips. To do this, use either dowels, or, which will be even easier, small self-tapping screws. To get it right, the slats must be fastened with gaps of 5 mm on each side along the width of the seat and back. The back and seat can be connected to each other with a metal corner, or a metal strip bent along.

If we do it on dowels, then we drill holes in the seat for fastening to the crossbars of the chair. Mount better on 4 pcs. standard cylindrical dowels. For the back of such dowels - 2 pcs. We connect the sidewalls with crossbars on which the seat will then lie. We do it without glue to check and see the positions of the seat and back. Also, without glue, we put the seat on the crossbars on the dowels. Bending and bending the back, mark the position of the bar for fixing the back, and then disassemble. If you wish, you can cut off the side of the backrest according to the picture. No desire - everything will be fine too.

At the children's highchair for feeding a wooden transformer, we sheathe the seat and back with a soft filler with our own hands: we glue it to the hard part or nail it with a stapler. Then, again with the help of a stapler, we stretch the upholstery. It is better not to save, and do not try to fasten the upholstery and the soft part with the same bracket. Something might be skewed, and it will not be good.

Then we collect all the parts on dowels smeared with glue. We put in place, check the corners. We fasten the back bar to the back on 2 cylindrical dowels. We check the gaps and tighten with clamps or a rope. We are waiting for it to dry. That's it, a chair from a wooden transformer highchair for feeding with your own hands is ready .

We repeat. If there is no desire to mess with dowels, all parts can really be connected using ordinary self-tapping screws. It may not be as strong, but it is easier to assemble. To decide, of course, the master. And it is most convenient and most durable to fasten the roundings with the help of dowels, and then carefully coat them with glue. After that, leave the finished sidewall to dry for a day.

The last stage: we cut out, according to the size, a small table on a high chair with our own hands. It can be left rectangular, it can be rounded in the part closest to the child. It's not essential. Only a matter of aesthetics and fuss. This table is attached to the edges of the armrests. It is possible on cylindrical dowels, it is possible on self-tapping screws. And when the child grows up, he just takes off and that's it, he is no longer needed.

A table for a do-it-yourself highchair is assembled in the same way as a chair. First dry, then with glue. Either self-made dowels or self-tapping screws are used. We start with the sides. We attach the upper and lower strips to the legs, we get two rectangles. When the sides are assembled, they, like the chair, must be pulled off and wait a day until they dry.

Next, the transverse bars are attached - with their help, the sidewalls are connected. We fix the crossbars for the feeding table with our own hands according to the drawing. The general idea is that they should be at unequal distances from the edges of the sidewalls. On the lower ones, which will be closer to the edge, there are chair legs in the high chair position. And the upper ones serve as spacers for the legs of the chair, so that the chair stands firmly.

A tabletop cut from plywood or chipboard is mounted on top of the upper parts of the sidewalls and screwed on with self-tapping screws. Everything is gathered together and pulled together as usual, waiting for it to dry.

When the table and chair for feeding with your own hands are ready, we will turn it into a transformer chair for feeding the baby. To do this, we will connect them. The table is turned over, the tabletop is at the back, and the chair is placed on the transverse bars of the table.

Wooden do-it-yourself transformer table for feeding a baby - finishing touches

Finally, when the chair and table are ready, we check for roughness for the last time and sand it if we find one.

When a wooden chair and a transformer table for feeding a child are made with your own hands, they should be completely worked through - use exclusively non-toxic varnishes, or paint with acrylic paint. Beforehand, to give the desired color, you can wash and dry.

Everything, the first option is ready. The most adequate description was found on http://mebelsam.com, from this site material was taken for a note on the first option.

Do-it-yourself wooden transformer highchair - Option 2

To understand what a do-it-yourself highchair will be in the form of components of option 2, we present the drawings and dimensions.

To make parts of a children's highchair for feeding a wooden transformer with our own hands, we take a beam with a section, for example, 20x30 mm. From it will need to do the following details: specify the length and quantity.

DIY feeding chair dimensions of spare parts, length and quantity

If there are no rounded parts

  • Legs 450 mm 4 pcs.
  • Armrests - 365 mm 2 pcs.

If there are rounded parts

  • Front legs 450 mm - 2 pcs., Rear 390 mm - 2 pcs.
  • Armrests - 290 mm 2 pcs.
  • Rounded detail according to the scheme - 2 pcs

General

  • Bottom strips on the sidewalls 365 mm 2 pcs.
  • Cross bars 350 mm 4 pcs. They are attached to the seat and back.
  • Seat (H x W) 290x330 mm
  • Backrest (H x W) 450x330 mm

DIY feeding table dimensions of spare parts, length and quantity

  • Legs - 450 mm 4 pcs. The legs are located in the middle of the table, and are the lower slats of the sidewalls.
  • Lower and upper crossbeams, on which the table for feeding is in the position of a table-desk, and to which the tabletop is attached - 500 mm 4 pcs.
  • Cross bars 410 mm 3 pcs.
  • Tabletop (H x W) 500x510 mm
  • Fastening straps for chair legs length 230 mm. ATTENTION - in the diagram, the thickness of the bars is 15x15 mm, but you can use any. For example, the same 20x30 mm.

Do-it-yourself wooden highchair transformer for feeding a child - The main differences from option 1

The previous part about a wooden highchair transformer for feeding a child with your own hands turned out to be too voluminous. Therefore, in order not to write a sheet again, let's say that everything is done according to the drawing and dimensions similarly to the first option.

Dowels are not used, with the exception of the rounded parts of the high chair. They are made, as well as in option 1, only they have different sizes. Everything else is fastened with screws. It can be ordinary on wood, it can be euro. If you use euro self-tapping screws, then mark the places where they should go. And in a place with a smaller diameter, we drill a hole for them.

Do-it-yourself highchair - we make parts and assemble

The bars are cut to size. Carefully processed with sandpaper. The cardinal difference from the first version of the do-it-yourself highchair is the absence of special round parts. But since sharp corners are an increased danger for a small child, they must be rounded. It is the upper parts of the chair legs that are slightly rounded on one side. And the two lower crossbars of the table are also rounded - the legs on which it stands.

You can also insert a few bars, rectangular or round, in the sidewalls between the armrest and the bottom bar to which the seat is attached, it does not matter. You can place them anywhere at any distance, most importantly in the seating area. This is so that the baby does not crawl away through the sidewall, and it will go for beauty.

One more stroke.
How to make a do-it-yourself high chair with a movable back? You can make the back of a do-it-yourself feeding chair take several positions. This will have to be dealt with.

To do this, the rear legs and armrests are fastened together using a round part, as was the case in the first version. In this case, the size of the armrest and back leg will be different (see the description of the dimensions of the chair). In the rounding, you need to make a hole where, as a result, a screw will be inserted, with a handle - a fixer at the end. The screw is attached to the back of the chair with one side, the other goes through this hole. The handle is screwed on the edge and secures it in the desired position. The back is fixed.

The hole can be made either with a milling cutter, or several small holes can be made with a drill and then modified with a chisel. The size of the hole depends on the screw used. The handle can be whatever you like. In the handle, carefully select the groove for the nut, which will actually be screwed onto the screw and fix the back of the chair. The screw itself is conveniently fixed not in the back of the chair, but in the upper crossbar.

Once again, we note that the rounding of the highchair for feeding with your own hands is more convenient and better fastened with glued dowels. On self-tapping screws it will be uncomfortable and clumsy.

Specifically for the baby, this version of the chair is very convenient, but to make it, you will have to make some efforts. If there is no desire, then it is realistic to do without a movable back, then it makes no sense to make a separate rounding. Just tilt the back as you and the baby are comfortable. We mark the place where the upper transverse bar touches the backrest and the sidewall. We drill a hole there. We fasten the sidewall and back with a self-tapping screw. So on each side.

When the sidewalls for the do-it-yourself highchair for feeding are assembled, two transverse fastening strips for sitting and one on a movable cylindrical dowel for fastening the back are screwed to the lower strips of the sidewall. A movable dowel means that one of the grooves is several (mm) larger than the diameter of the dowel.

The back and seat is done in the same way as in the first version. Only the dimensions here are slightly different - a longer back. It's more convenient for the baby. It is also not necessary to fasten the seat and back together, it is enough to attach them to the transverse slats, and subsequently make them soft and upholstered, for example, with oilcloth. Before upholstery, as usual, skin and paint.

That's it, the do-it-yourself highchair for a children's wooden transformer is ready.

DIY high chair table

A do-it-yourself table for a highchair for feeding is assembled in the same way as in the first version. Sidewalls first. When the sidewalls are assembled, they are fastened together by transverse strips located below - they also serve as supports on which the assembled chair stands. This is important as the high chair is mounted on them and plays a role in its solid installation.

This is the difference from the previous version - there is no additional crossbar in the middle at the bottom of the table, which makes the table not closed, and it is more convenient for an older child to sit at it. At the same time, two crossbars go only from below, where the tabletop is attached - there is only one crossbar. When everything is assembled, it remains to screw the countertop.

There is one moment.
How to make a table top for a transformer highchair for feeding with your own hands? The figure shows the diagram and dimensions of the variant with grooves. For simplicity, the table top for feeding with your own hands can, as in the first version, simply be put on the bars, or you can, as they do at the factory, clamp between the bars. The first option is simpler, but the screws will be visible in the most inappropriate place. The second will require more fuss, but more beautiful. To clamp between the bars, you need to make grooves in them. This is done without problems with a milling cutter, or just a chisel, but it takes longer. Accordingly, the dimensions of the tabletop will be different. The groove is washed away to make the thickness of the table top and a depth of 5 mm.

For greater stability of the highchair standing on the table, in the assembled form of a do-it-yourself highchair for feeding a wooden transformer, you can additionally make four small bars - two on each side. They are located under the countertop, it is better to put them on the "fact". Those. when the table and chair are ready, we put a chair on top of the table, as it should be in the end. We mark from the inside on the sidewalls of the table, where the chair legs closest to the table top pass. On the sides, parallel to the markings, we attach these bars to the sidewalls of the table, one on each side. As a result, it should turn out so that the legs of the chair closest to the countertop pass between these bars, and they, in turn, do not allow the chair to move in different directions. This gives the chair extra stability.

The do-it-yourself feeding table is ready.

DIY highchair - summary and some conclusions

As usual, summing up, we talk about what is easier - to make a highchair for feeding with your own hands, or to buy? The answer is clear - buy. Moreover, wooden transformers are very common today and are inexpensive. But there are people who want to make their own efforts and imagination, or maybe someone has not sorted out the rubble of their building materials for a long time. Then go - creativity has been valued at all times.

The first option, of course, is the most common on the Internet, but it is not the easiest. There you have to fiddle with dowels, make grooves, glue parts. It's great if there is a special large clamp, as an ordinary rope can warp the part. And the details, if you do not compress at all, then maybe nothing will work out at all. In short, take a lot. In addition, over time, such a product will definitely dry out, remember the old swinging chairs. And your child will definitely rock a ready-made highchair for feeding with your own hands.

The second option is not common on the network. But this do-it-yourself high chair looks like a factory transformer high chair. Assembled on self-tapping screws. The main thing is to ensure that during assembly the mating parts of the parts stand at 90 degrees to each other and do not warp. Take a little. Only if you want to make a movable back with a rounded element, then you have to sweat.

At one time, when they wanted to make a wooden transformer for feeding with their own hands, we knew the first option. But he seemed complicated. And then, when they bought a factory one, they found its dimensions and realized that it was no worse, and maybe even better than the first option. If I had to do it myself another time, I would choose the second option.

How to make a do-it-yourself high chair video craftsmen

In principle, every craftsman makes his own transformer chair for feeding with his own hands. So to speak, according to your needs and with your capabilities. Here are the most understandable and popular videos. From them it will become clear that the beam can be of any size. The dimensions of the chair-table for feeding can also be any. The main thing is to capture the essence of the design and sequence - how to make a highchair for feeding with your own hands.

With a large number of modern materials, wood still does not lose its relevance. This is especially true of furniture for children. Of course, you can buy a children's wooden chair in the store, but often they are made of plywood and are not of high quality. And children's wooden adjustable chairs, made from good hardwood, are very expensive. To give your child a durable, beautiful and comfortable chair without spending a lot of money, you should make it yourself. In total, there is a wide variety of models, but the article will discuss three main ones: a regular high chair, a transformer and a high chair for feeding.

Do-it-yourself children's wooden chair

Before proceeding with the manufacture, we must remember that children's furniture must be safe for health. It should not have sharp corners, have a perfectly smooth surface, without cracks, cracks and gaps, and must also be strong and reliable.

The optimal height of the backrest of the highchair is 55 cm, the seat is 32 cm. You can fasten the parts in different ways: on self-tapping screws, nails, dowels (at least 2 pieces for each joint) or wooden spikes. Let's consider the last option.

To fasten the structure, strong hidden rectangular spikes are used, which are seated in the grooves with glue. For the greatest reliability, the spikes, in addition to glue, are fixed in the grooves with through dowels with a diameter of 6 to 35 mm.

List of parts and materials

  • Upper crossbar (1) 1.9x4.1x16.5 cm - 1 pc.
  • Rear leg (2) 3x3x55 cm - 2 pcs.
  • Carved crossbar (3) 1.4x4.1x16.5 cm - 1 pc.
  • Middle bar (4) 1.4x2.9x16.5 cm - 1 pc.
  • Boards for the seat (5) 1.4x10.5x26.3 cm - 2 pcs.
  • Lower crossbar (6) 1.4x2.9x16.5 cm - 1 pc.
  • Side bar and drawer side (7) 1.4x2.9x17.7 cm - 4 pcs.
  • Front leg (8) 3x3x30.5 cm - 2 pcs.
  • Front crossbar and drawer side (9) 1.4x2.9x19.5 cm - 2 pcs.

For the rear and front legs, straight-layer pine bars with a section of 3x3 cm are used. Starting from the seat up, the rear legs should taper to 1.9 cm. And the front legs - from the seat to the bottom to 2.4x2.4 cm.

Important! Only outer edges can be planed. This is necessary so that the inner edges of all legs remain parallel to each other, which will ensure easy installation of the sides and crossbars.

At the top of the crossbar, the front edge should be rounded, and the carved one can have any pattern, but it is desirable to avoid sharp corners.

The middle bar is installed in such a way that its lower edge is flush with the seat.

First of all, the back pair of legs is glued together, as well as all the crossbars. Further, a pair of front legs and a crossbar are connected, after which they are connected to each other by drawers and crossbars.

All gluing points are compressed with clamps, but with the obligatory control of right angles. To do this, you can use a carpenter's square. Lastly, the seat boards are attached. Their reliability is especially important, therefore, after the glue has completely dried, they are additionally reinforced with wooden dowels, for which holes must be drilled. The protruding ends are removed with a chisel.

Children's wooden chair-transformer

It is a set of children's table and chair, which can be transformed into different positions. This is both a single desk for classes and a comfortable chair for feeding. It is compact enough to fold, which is especially important for small apartments.

Required parts for the chair:

  • legs 39 cm - 4 pcs.;
  • rounded corners - 4 pcs.;
  • upper crossbars 22 cm - 2 pcs.;
  • crossbeams 34 cm - 2 pieces;
  • cross 30 cm - 3 pcs.;
  • seat base 20x30 cm - 1 pc.

Table details:

  • legs 50 cm - 4 pieces;
  • planks 41 cm - 4 pieces;
  • cross-sections 34 cm - 4 pieces;
  • tabletop 45x38 cm - 1 pc.

For legs, planks, crossbeams and crossbars, it is best to use a beam with a section of 2x4 cm, and 1.8 cm thick plywood is suitable for the tabletop and seat. Rounded corners are cut from a 2 cm thick board. As already mentioned above, the wood should be well dried and have no knots or cracks.

Making a chair frame

All parts will be glued together, but to ensure higher strength, wooden dowels 2x5 cm in size should also be used. They are easy to make with your own hands from 8 mm thick plywood.

For each dowel, a special groove is made at the junction. First, with a drill (drill 6 mm), the ends are drilled in the place where the dowel will be laid, and then the groove is directly selected with a chisel 8 mm thick. But before installing it, all connections must be smeared with glue.

Thus, the side parts of the future chair are assembled, pulled together with clamps (while making sure that the angle is exactly 90 degrees) and left until the glue dries completely. Below is a drawing of a children's wooden chair.

After that, they must be well sanded until the surface is smooth.

back and seat manufacturing

The back and seat are made in the size of 25x30 cm from 2-3 sheets of plywood glued together. All corners should be rounded off. Foam rubber is glued to them and everything is covered with a fabric cover. Before installing them on the chair frame, they are fastened together with metal brackets.

Now let's start assembling the chair. First, with the help of planks, two finished sidewalls are connected. Fastening is carried out according to the technology already described. The seat itself rests on the slats, and to fix it you will need cylindrical dowels or self-tapping screws. Then the lower bars and the back bar are installed, on which the back will be mounted. After all the work done, you should leave the chair to dry.

In addition to the main table, you can also make a small countertop. It is especially convenient for feeding or playing small children. For its manufacture, you will need a plywood sheet, from which the countertop of the required size is cut. It is attached to the armrests with glue and dowels. But it is wiser to attach it to self-tapping screws, this will allow, if desired, to easily dismantle it.

Table making

The assembly technology of the table is absolutely identical to the assembly of the chair. Therefore, there is no need to paint it in detail, you just need to pay attention to the main stages. First, the side parts of the table are assembled and skinned, then they are connected by transverse strips and skinned again.

When the children's wooden transformer chair is ready, it is covered with several layers of varnish.

High children's wooden chair for feeding

Making furniture with your own hands is a laborious process. These days, it’s easier to buy ready-made or order than to do it yourself. But there are times when a thing is needed for a short time or there is no way to give a lot of money for it. One option is a high chair for baby feeding. The advice below will show you how to make one from an old chair with your own hands.

Children's wooden chair assembly diagram

To make it, you need the simplest chair with a back. It is very good if it has. It is important that it has crossbars between the legs and is strong and reliable. In the future, turning it over, the back will serve as the front legs of the future chair. Next, you will need strong wooden slats the size of a chair height, we fix them as shown in the figure. So, it turns out the back pair of legs, which are fastened together with a bar. To achieve maximum stability, the rear legs must be mounted at an angle that is selected individually. Then all the legs are fastened together with horizontal slats.

The frame of the future chair is ready. To make it more convenient to use, you can attach smoothly sanded boards or a sheet of plywood as a seat. A soft seat is placed on top of it. Small smooth boards are used for the back and table top.

That's all, the chair is ready.

It doesn’t matter how the children’s wooden high chair is assembled, most importantly, it should turn out to be comfortable and safe for the child. In order for the finished chair and table to have an aesthetic appearance and last as long as possible, they are covered with a protective paint and varnish composition in several layers. In addition, all wooden parts can be decorated with bright patterns, which are applied with a simple brush or sponge through a stencil.

For seat upholstery, it is optimal to use artificial leather, because it is easy to clean. This is especially true for young children. It is desirable that the back of the chair will also have a soft upholstery made of waterproof fabric.

All wooden parts, before assembly, must be carefully processed with sandpaper, first coarse-grained, then fine-grained, until a perfectly smooth surface is obtained.

If the chair is assembled on self-tapping screws, their hats are deepened and closed with plastic plugs matched to the color.

In addition, you can dream up and make the chair colorful and interesting for the child, choosing a bright upholstery fabric, and painting all the wooden parts with oil paint in bright colors.

And you can entrust the design to the future owner of the chair.

Children's wooden chairs photo

Fitting © 2022 Design and interior of apartments