How to decorate a frame house inside. Exterior decoration of a frame house: what options exist. Rough interior decoration of a frame house

Prefabricated houses created using frame technology are increasingly being installed in our country for permanent residence.

Not only allows you to save time on the construction of the structure, but allows you to make a building with good performance. In addition to high strength and excellent thermal insulation of the walls, the frame house can be finished both outside and inside with various materials, which opens up scope for creativity and transformation of the walls of this design at your discretion.

The article will discuss how the finishing of a frame house is carried out.

Exterior finish

Outside surfaces are exposed to moisture, freezing temperatures and heat during the summer months. To protect the facade from negative impacts, as well as to give the structure a more aesthetic appearance, the exterior of the frame house is finished with special materials.

Many types of finishing materials can significantly increase the strength of the structure, which allows the base to withstand high wind loads.

So, consider the options for exterior decoration of a frame house.

Plywood comes to the rescue

Plywood is attached to the main wall with self-tapping screws, then painted with any weather-resistant paint. The advantage of this method lies in the high speed of work, good appearance and an increase in the mechanical strength of the structure.

The cost of external finishing with plywood, in terms of 1m2, does not exceed 350 rubles.

Brick use

Brick is a traditional finishing material for houses of various designs, including cladding of frame houses. The use of the material is more expensive in all respects, but the heat saving coefficient is maximized.

The use of bricks for exterior decoration allows you to save a lot on heating and air conditioning of a residential building.

The aesthetic qualities of this finishing material are also difficult to overestimate, and due to the high mechanical strength, the highest level of protection of the frame structure from the effects of adverse natural factors is achieved.

Wooden block house

The use of a block house for finishing a frame house is the most promising direction in carrying out this type of work. The use of high-quality lumber will not only bring the outer surface into proper shape, but also significantly strengthen the walls of the frame structure.

Can be attached directly to the outside of walls. But if additional insulation of the structure is necessary, then in this case a crate is made into which a heater is installed, followed by sheathing with lumber.

Siding panels

Insulation and siding of a frame house is one of the easiest methods.

Thanks to the huge range of these facing materials, you can choose the color scheme that is most in harmony with other elements of the house and the surrounding landscape.

Thermal panels

On the modern market, you can purchase decorative elements that are easily installed on the outside of the frame building, perfectly protect the walls from the penetration of cold and have a presentable appearance.

Thermal panels can imitate various types of masonry or building sheathing with lumber. The material of these building materials can also be different.

Most often on sale you can find thermal panels made of foam and. Such products are lightweight, easy to install, but perform only a decorative function and are used to reduce thermal conductivity.

Thermal panels have a significant drawback: it will not work to increase the mechanical strength of the building using this material.

Plastering

It is a rather labor-intensive way to improve the appearance of a frame house. The complexity of the installation of this coating lies in the need to have a sufficiently high level of skill to apply plaster in an even layer.

Significantly complicates and increases the cost of the coating process, mandatory preliminary surface preparation. Which consists in applying a sealant at the joints of the walls and installing a special reinforcing mesh along the entire outer surface of the walls.

Coloring

How to sheathe a frame house from the outside, if there is no need for additional insulation and a change in geometry from the outside. In this case, outdoor work may be limited to painting only.

For this purpose, special coloring compositions for OSB are used, which are able to withstand the negative effects of the environment well. In addition to staining, the outer surface can be treated with special compounds containing powders from crushed stone.

Any of the listed options for external cladding can be successfully implemented in practice. Which method to choose depends on personal preferences and financial capabilities.

Interior decoration of a frame house

After the construction of the building, they begin to restore order inside. Interior work can be divided into the following finishing stages:

draft;
fine.

Rough finishing is necessary only if the building has just been built and repairs have not yet been carried out. This category of work includes:

pouring floor screed;
wall insulation;
installation of windows and doors.

Finishing or finishing is the application of decorative materials to walls, floors and ceilings.

Draft work begins with wall cladding. Popular materials for this work are drywall and OSB.

Drywall

By installing this finishing material on a metal profile or a wooden crate, you can achieve high productivity and a good final result.

Due to the sufficient gap between the wall of the house and the drywall sheet, it is possible to completely hide the electrical wiring in this cavity, and also lay a layer of insulation if necessary.

Watch an interesting video about the installation of drywall in a frame house:

It has a small mass, so the material can be successfully used for finishing the ceiling. Multi-level ceilings made of plasterboard sheets look especially impressive.

OSB

Compared to drywall, it has more weight, so special self-tapping screws are used for reliable fastening. They are not installed on the ceiling, but can be successfully used for the floor.

OSB is laid on the floor in such a way that the logs are perpendicular to the length of the slab.

Clapboard lining

The lining is installed on a metal or wooden frame, which is securely fixed to the main surface of the house. Then the material is attached to the crate using self-tapping screws.

In addition to natural lumber, artificial products can be used, which
their appearance imitates natural timber. Installation is simplified by a special latch installed along the edges.

Tile

The interior decoration of a frame house in rare cases can be done with tiles.

In contrast to the installation of sheet products for the installation of tiles, it is necessary to use an adhesive composition. Installation work must be carried out using a level to ensure even masonry.

fine finish

After the surface of the walls and ceiling are leveled with materials such as:

drywall;
plywood;

Be sure to need work to improve the decorative appearance of the surface. Inside the house, finishing can be done with.

Wallpaper

Simple and popular material. Inexpensive are paper wallpapers, which are easily glued to a pre-prepared surface.

In addition to paper for interior decoration of a frame house, the following can be used:

vinyl;
textile;
non-woven;

Coloring

The surface inside the house can be painted with various dyes. Depending on the type of product that was used for sheathing, the most suitable type of paint is selected.

For reliable fastening of the paintwork substance to the surface, the base must be primed with a properly selected primer.

Decorative plaster

This type of finishing work can be done on drywall and after sheathing the walls with OSB boards.

To obtain high-quality coverage, you need to follow the technology. With special care, plastering of drywall is carried out. When applying a plaster layer, its thickness should not exceed 10 mm.

Conclusion

Finishing the facade and interior of a frame house can be done using various materials. After choosing the right option, you can entrust the work to professional builders or do it yourself.

When carrying out the interior decoration of a frame house, several important points should be taken into account: the correct sequence of stages, preparatory work, features of materials and the rules for their installation.

After the erection of the walls and roof, it is the turn of the interior decoration of the premises of the frame house. In order not to make mistakes in the process of repair and finishing work, we recommend that you familiarize yourself with their features in the field of frame construction.

Stages of interior decoration

To ensure high comfort of living in the house, it is necessary to pay attention to each of the three stages of the interior decoration of the frame house.

Aligning posts and beams

To make the subsequent stages of finishing easier, you need to prepare the premises. Under the condition of high-quality construction, all racks and beams in the room should be even. You can check this using the building level.

In case of poor-quality laying of the floor, it is leveled with wooden wedges hammered into the places where the beams are attached.

Warming and soundproofing

The process of warming the floor of a frame house

Recently, these two concepts are increasingly used as a whole, since modern materials have both noise and heat insulation properties. Mineral wool, polystyrene, polyurethane foam, foamed rubber, expanded clay (for the floor) are popular.

If your house is located in an open area, it is recommended to lay a layer of wind protection before laying the insulation - this way you will ensure a higher temperature in the house in winter.

Usually start from the floor. A draft floor is laid out on horizontal beams, the surface of which, in turn, is covered with the selected material. Another layer of the floor is laid on top, usually these are boards with an aesthetic appearance with special impregnation or treatment (if it is not planned to finish the floor), or ordinary boards.

The walls and ceiling are insulated in the same way, sheets of insulation are laid out between the beams, and then covered with a rough finishing material.

To insulate the ceiling, you can purchase foam, its weight is much lighter, so for ease of attachment, you can use a hot glue gun.

In the bathroom, toilet, boiler room, bath or sauna, you must also put vapor protection.

Rough finish

How to properly fix drywall

For rough interior decoration of frame houses for wallpaper, plaster, tile or painting, gypsum boards are most often used. This is an economical, high-quality material that will allow you to create a perfectly flat surface for fine finishing.

At this stage, it is necessary to cover the walls and ceiling with gypsum boards, as well as erect the planned gypsum board structures (partitions, niches, arches).

Drywall sheets are recommended to be fastened according to the step of the frame: each sheet must begin on the frame and end on it. Sheets are fastened to self-tapping screws with a screwdriver at a distance of 20-30 cm from each other. You need to leave a gap of 2-3 centimeters to the floor (then it will close with a plinth).

Before proceeding to the next stage, the joints must be puttied in 2 layers (after each layer has dried, it must be leveled with sandpaper), and the walls must be plastered.

In rooms with high humidity, it is necessary to use a special moisture-resistant drywall for the rough finish of walls and ceilings.

There is another option for the rough finish of a frame house - these are OSB boards. According to their characteristics, they are similar to drywall, but have a more environmentally friendly composition. However, they are quite heavy, so you should not choose this option if you do not have the skills to work with it.

fine finish

The final stage of finishing involves laying finishing materials, or wallpapering, laying tiles or painting walls. Let us consider in more detail the types of possible materials for the interior finishing of a frame house.

Types of wall materials

Wallpaper has been the most popular finishing material for several decades. They are inexpensive, and even an unprepared person can glue them - the main thing is to follow the instructions.

Wallpaper

Types of wallpaper and their characteristics:

Paper - the most economical type of wallpaper, ideal for budget or temporary repairs. Their main drawback is instability to moisture and drafts.
Photo wallpapers are recommended to be glued in rooms without windows or small rooms to create the illusion of a larger space or give the interior a more original look. The characteristics are similar to paper counterparts.
Vinyl wallpapers are more durable and strong than paper ones, but their price is higher.
Acrylic wallpaper is suitable for rooms with high humidity.
Non-woven wallpaper creates an ideal surface for finishing wall painting.
Fiberglass wallpaper is the most fireproof type, which is ideal for finishing a frame house, both for finishing and for painting.

When buying wallpaper, pay attention to the type of glue that is most suitable for them. For different types of wallpaper, certain types of glue are required.

Ceramic tile

Finishing in the bathroom, toilet, kitchen or swimming pool requires high strength and moisture resistance from the finishing material. The perfect combination of these characteristics is ceramic tiles. This material has a low price, but at the same time, the variety of shades and textures will make it possible to realize even the most daring design ideas.

Tiles can be used on both walls and floors. It is easily attached to any plastered surfaces, including drywall.

clapboard

A popular option for interior decoration of a frame house is. Due to the high heat and noise insulation characteristics of this material, it is excellent for cladding the walls of a frame house. In addition, the walls finished with natural wooden clapboard look very cozy and aesthetically pleasing, especially if the house is a country house.

There is also a more budget option - plastic lining. It is very easy to mount it, and it will serve for more than one year. Plastic clapboard can be used to decorate the walls and ceiling in the bathroom if the tile seems to be too expensive an option. It should be borne in mind that such a finish will look simple and without frills.

Liquid wallpaper

One of the recently invented finishing technologies that has already won a lot of fans is liquid wallpaper. They are good for their decorative component and the ability to hide minor flaws and wall irregularities. However, the method of applying them is not easy and time-consuming.

Decorative plaster

If you want to create an original designer wall covering in your frame house, consider finishing with decorative plaster. Thanks to various textured rollers and ease of application, decorative plaster is perfect for creative people who do not have special repair skills. In addition, an important advantage of this material is its low price.

To make the interior more original, you can combine several types of finishes, such as painting and decorative plaster, or wallpaper and wall panels.

The main thing is to know when to stop: it is better to use additional decorative material for zoning individual objects: headboards, TV sets, etc.

Types of materials for the floor

If you want to combine the rough and finish of the floor, while saving time and money, you can cover the floor with a grooved board. This natural material will serve you for a long time and, if properly processed, will have an aesthetic appearance.

grooved board

The best option would be a larch board: it has a higher moisture resistance than a spruce or pine board, but at the same time, unlike oak or ash boards, it is not as attractive to beetles.

The grooved board is laid on a screed or logs.

After purchasing the tongue and groove boards, bring them into the house and leave them there for 2 weeks. This will ensure that the material is perfectly moist and the new floor will not change in size after installation.

Parquet

One of the most environmentally friendly, high-quality and durable materials, especially if it is natural. However, it is expensive, but it is very susceptible to high humidity.

Laminate

The material is average in almost all respects. It is difficult to call it environmentally friendly, and it is not resistant to moisture, so for a nursery it is better to prefer some other option. At the same time, laminate flooring lasts a long time with careful handling, is inexpensive and easy to install. It is perfect for the floor in the living room or in the hallway.

Laminate is laid on a special substrate that gives the floor elasticity and reduces the likelihood of damage.

Tile

For interior decoration of the house, ceramic or cork tiles are most often used.

Ceramic tiles are especially suitable for decorating the floor in the bathroom, in the kitchen, as well as islands at the front door. This is the most wear-resistant material, while one of the easiest to clean.

Ceramic tiles are the best choice if you are going to make a "warm floor".

This material has a high heat transfer, while it does not deform from constant exposure to heat, like laminate or parquet.

Cork tiles are a fashionable trend for connoisseurs of everything natural. It is quite expensive, but its main advantage is environmental friendliness.

Even a chronic allergy sufferer can live comfortably in rooms with cork floors. Its main drawback is vulnerability to heels.

Linoleum

The most budget option for flooring, widely used in the decoration of houses in the USSR. Its main advantages are good heat dissipation and moisture resistance, but other characteristics are inferior to competitors: it is susceptible to chemical attack and is easily damaged.

Carpet covering

If you want the room to be comfortable to walk barefoot, feel free to buy carpet. It is inexpensive and very easy to install. Carpeting has the highest heat dissipation and good moisture resistance, but at the same time it is not very practical: any stains will be visible on light shades, and it is also very easy to damage the surface.

Whatever materials for interior decoration you choose, you must carefully read the instructions for them. If you are going to finish the house yourself, be sure to study the step-by-step decoration instructions on the Internet to avoid mistakes.

After the construction of the house using frame technology, the stage of finishing work begins. First, rough finishing of floors, walls and ceilings is carried out, for example, with oriented strand boards or gypsum boards. In the future, fine finishing materials are applied to them: plaster, wallpaper, tile, lining, board for timber, etc.

For rough and fine finishes, there is a choice between alternatives. Each of them has its own specifics, appropriately suited to certain operating conditions.

The task is to choose the best option, it is not worth paying for the outstanding properties of the material if they are not used.

Peculiarities

Internal finishing works consist of two main parts: rough and finish. The first includes the choice of material for wall cladding, their insulation, floor screed, installation of window systems and doors, slopes for them.

Internal walls can be sheathed:

drywall;
wood boards, such as OSB.

After that, the final lining begins, the following materials are suitable for it:

lining;
wallpaper;
decorative plaster;
ceramic tile;
flexible stone, etc.

Correctly and beautifully bricked sheathing frame is also quite popular today. This is ideal, for example, for giving. DSP and other materials can also be used.

materials

When choosing a material, it is important to take into account the specifics of the room: what it is intended for and what the operating conditions will be.

Drywall

The material, which allows achieving perfect evenness and smoothness of the walls, is distinguished by an affordable price, but weakly resists loads.

With the help of drywall, it is easy to create various bumpers, ledges and other relief decorative elements.

Other features of the GCR include the following points:

relative lightness simplifies finishing work, the material does not load the structure;
perfectly hides the unevenness of the finished surface;
cannot be used for flooring;
poor moisture resistance (except for a special subspecies);
easy installation on a profile frame;
inside the frame, you can carry out communications: pipes and wiring, as well as place additional insulation;
short finishing work.

OSB

A material that is somewhat similar to GKL: it gives a smooth and even base for finishing work, it also compares favorably with an affordable price. The characteristic differences include higher strength and a significantly larger mass, which determines other requirements for the room and the structure as a whole.

Features of oriented strand boards include:

need more durable mounting means, at least two people are required to work on their fastening due to the significant weight of the sheet;
can be used to cover any surface: walls, ceiling, floor;
more moisture resistant than GKL, but still need additional varnishing.

timber imitation

The material is distinguished by excellent operational and aesthetic qualities, it can act as both a rough and fine wall finish. The main disadvantage is the relatively high price of the material.

So that the finish does not visually resemble lining, it is recommended to use panels with a width of more than 90 mm.

Other characteristic features of timber imitation include:

excellent heat and noise insulation;
outwardly indistinguishable from more expensive analogues: profiled and glued beams;
does not shrink or crack;
easy to install, one person can do the work, a reliable fastening system ensures the structural integrity of the wall;
a huge number of wood species determines a wide selection of textures and shades with a characteristic pleasant smell;

moisture resistance depends on the selected breed;
price variability, there are both budget options with good qualities (pine, spruce, etc.), and expensive species with more impressive properties (oak, cedar, tropical species), while imitation timber is cheaper than profiled or glued counterparts;
resistance to temperature extremes;
high flammability, the level of which can be reduced by flame retardant impregnations;
susceptibility to fungal mold at high humidity, may be reduced by antiseptic impregnations;
requires constant updating of the protective coating - varnish;
rotary and corner elements have a higher cost.

Wallpaper

A finishing material that provides a wide choice not only in terms of aesthetic diversity, but also in terms of species. Wallpapers on various bases (paper, non-woven, vinyl and fiberglass) differ in operational features and are used for various specifics of the indoor environment.

Characteristic features also include:

a huge selection of external design, including texture, color, pattern, roll width;
easy installation does not require professional skills, can be carried out by one person.

Features by subspecies:

paper vulnerable to moisture, have poor wear resistance and durability, low price;
vinyl resistant to mechanical stress, moisture resistant and durable;
non-woven serve as an excellent base for decorative painting;
fiberglass have high strength and uncharacteristic fire safety for wallpapers, lend themselves well to coloring.

clapboard

A wooden product that has a pleasant appearance and greater affordability than timber or its imitation. Suitable for all lovers of environmentally friendly materials and savings. Other properties of the lining include:

a wide selection of wood species with a specific texture and shade;
high resistance to abrasion and mechanical stress;
the smell of wood has a positive effect on the mood and well-being of residents;

good noise and heat insulating properties;
price variability: lining differs in cost not only by wood species, but also by grade, which makes it more affordable and allows you to use it even with low incomes;
needs to be coated with a protective compound and its cyclic renewal;
good combustible - poor fire safety, can be reduced by flame retardant impregnation;
susceptible to fungal mold, can be reduced with an antiseptic solution.

Plaster

Finishing decorative plaster fits well on walls already finished with GKL or OSB and creates a smooth surface with an excellent appearance.

The main properties of plaster include:

a wide selection of colors and shades;
resistance to temperature difference;
good moisture resistance;
the non-porous structure enhances thermal insulation, but hinders the natural ventilation of the walls;
if you want to redo the finish, the high strength of the material will turn out to be a minus, its dismantling will require a lot of effort.

Ceramic tile

Classic finishing material with excellent decorative qualities. You can also highlight the following characteristic features:

a wide range of colors, patterns and textures of the product;
complete waterproofing and immunity to direct water ingress;
durability;
full naturalness of the components;
high resistance to pressure and abrasion;
high-quality styling requires hiring a specialist;
difficulty when facing rounded and rotary surfaces.

flexible stone

A modern material that imitates a natural counterpart, it is flexible and plastic, and its texture is fully consistent with the original and just as beautiful. It is realized in the form of plates and wallpapers. Other features of flexible stone are:

high resistance to abrasion, pressure and shock loads;
environmentally friendly composition;
can cover surfaces with complex geometry;
processed and mounted easier than analogue;
durable, but inferior to the original.

Design

For facing residential premises, you can use the entire list of finishing materials.

When decorating a kitchen it is worth considering its specifics: high humidity and pollution in the cooking area, so for the “apron” it is better to choose a waterproof and easy-to-clean material, for example, ceramic tiles, flexible stone, plaster.
for bathroom, characterized by high humidity, all the same tiles, plaster are suitable, followed by painting with a moisture-resistant vapor-permeable type of paint: rubber, vinyl or acrylic.
For children resistant to abrasion and impact, safe, cleanable materials will be appropriate: laminate or lining with painting, decorative plaster are suitable for walls, linoleum, parquet, laminate are suitable for the floor.

How to do it yourself?

If you choose the option of finishing the house with your own hands, you must follow a certain methodology so as not to complicate the process with unnecessary waste of time and rework costs.

The decoration of the premises should be progressive: it is necessary to move from one completed room to the next. Finishing all rooms at the same time is inconvenient and impractical.
Repair of premises begins from the farthest end of the house from the door and moves in their direction. This sequence is associated with the need to take out the garbage, and, accordingly, dust and dirt, if you start from the door, the finished rooms will quickly get dirty.
It is necessary to start finishing work only after laying all communications: pipes, wiring, ventilation ducts and other things.

Finishing is done "from top to bottom": first the ceiling, then the walls, then the floor. This is due to debris falling down: if you start from the floor, then when finishing the ceiling, the floor covering and walls will get dirty. The only exception is suspended ceilings, they are mounted last.
All surfaces that are not related to the front of finishing work at this stage should be covered with a film to protect against debris. Thus, in the future it will not be necessary to clean them from excessive pollution. Of course, this concerns finished surfaces in the first place.

The duration of finishing work depends on several factors:

type of finishing work: painting the plasterboard is much faster than finishing the walls with a board under a bar, and then varnishing;
availability of building materials: if they are not previously purchased for the entire scope of work, there may be delays in delivery, lack of necessary items in the warehouse, etc.;
financial support;
other nuances.

With continuous work, finishing a house with an area of \u200b\u200babout 40 square meters. m takes a month, for an area of 60 sq. m this period increases to 1.5-2 months and so on. Starting finishing with your own hands, it should be borne in mind that these are the terms for permanent work, for which there may not be time, and then the finishing will drag on for years. An alternative solution is to hire a team of workers, which will reduce the time by several times.

Hello dear friends of my Internet project! Recently, the construction of frame houses in our country is increasingly spreading among the population. Frame technologies, as a section of construction, finishing of a frame house inside, let it be one or two floors, more or less appeared recently. Here we will all describe all the pros, cons, individualities and prospects for improving this industry. Everything is very simple. A characteristic feature of this constructive structure is considered to be lightweight and cheap, since the frame is made of wood from horizontal strapping and then vertical racks. The voids that take place are filled with special heat-shielding substances.

I launched an informative Internet project for the construction of skeletons. In order to understand the essence of the issue, I personally watched a bunch of videos and also sites of varying degrees of complexity in order to get techno information on my problem. And I dug up something for you. It is here that you will always find everything for the construction of load-bearing walls, the foundation of the foundation, the roof, the battens for it, and also other useful parts of the frame. I recommend this information to you.

Most amusing is the fact that the method of building frame houses is becoming a completely easy topic, which is why building a frame house on your own is not at all difficult. Here we describe in detail the entire installation process down to the smallest detail, analyzing all the main key factors and of course individual traits. You only need to apply it as a whole in the construction without anyone's help.

Block house inside the house - a non-standard solution

The name "block house" sounds nice and fashionable. But, by and large, this is a well-known lining - however, made using the most modern technologies. This material is designed to imitate a natural wooden frame, and the block house decoration inside the house is involved in creating a special microclimate.

Types of wood for a block house

Freshly processed wood has its own unique aroma, which is loved by many. And if the block house is made of conifers, then the substances it releases are a prophylactic against respiratory diseases. The healing properties of natural antiseptics present in needles have been known for a long time.

It is no coincidence that, for example, a pine block house in the interior of baths or saunas can be found very often. As for spruce, due to the friability and excessive softness of the wood, it is not used for interior cladding. It goes only on thin slats for cladding. Finishing a block house inside the house will be an excellent solution if you have to create an interior in country style. Its panels do an excellent job of imitating natural wood. They are usually used in living rooms, libraries.
The interior decoration of the block house looks good in real life and in the photo, if it is used in the hall, hallway, in the kitchen. On some photos on the Internet you can see the decoration of the attic with a block house - this option looks very interesting. Can an ordinary person cope with decorating his home with block-house panels? Does this material have any specifics associated with installation? Is it possible to decorate a room with a blockhouse from a photo or are there any non-obvious nuances? Finishing a block house inside the house usually involves the use of lamellas, the thickness of which is from 20 to 25 mm. If they are thicker, then the crate needs to be more massive, and it will take extra centimeters of usable area. Finishing inside the house with a blockhouse involves a preliminary calculation of the amount of material and fittings.

INTERESTING VIDEO

Attention should be paid to this stage, so that later you do not cut the panels once again and thus save a little. As a rule, they acquire the right amount with a margin of 10% of the calculated volume. It is important that the panels belong to the same batch and completely match in shade. If this is not the case, then the block house in the interior will look much worse than intended.

How to mount a block house

Finishing a room with a blockhouse, captured in the photo instructions, often begins with the installation of a crate. But in fact, it starts earlier: before facing, you need to free the lamellas from the packaging and give them the opportunity to lie down for at least two days in the room where they will be nailed. During this time, they will align with the environment in terms of humidity and temperature. If you deprive the material of this opportunity, then the lining may be warped.
Judging by the photo, decorating the walls with a blockhouse is nothing complicated. At the same time, the internal lining of wood has many advantages. If the room is sheathed with a block house, air passes freely under the material, which makes the local microclimate healthy. The walls that make up the block house can be made of any material. Large-scale and complex preparatory work to eliminate their flaws and irregularities is not required.

Getting to the interior decoration of the block house, you can see the photo, see how it's done. It is even better to watch a video about decorating a house with a block house.

The panels are mounted easily and quickly, this process is not accompanied by the formation of a large amount of construction debris and dirt. The material provides the walls with high-quality thermal insulation, and the decorative properties do not fail. The design can turn out to be very stylish, and ideas are brought to life quickly enough. Wall sheathing with a block house is quite inexpensive, which makes it even more affordable and convenient.

INTERESTING VIDEO

As for the minuses, one can not dream of cheapness if the panels are made of natural wood. It will not be possible to clad the walls and forget that a block house in the interior is a rather troublesome thing, you will have to constantly take care of the coating: wash, clean, cover with something. Over time, accumulation of dust is found at the joints of the panels.
Source: dompraktika.ru

Finishing a frame house inside

Wallpaper, paints with various effects, artificial or natural stone, woven materials, wooden and plastic panels will help to create a unique interior. Wallpaper is most often used for interior decoration. They have a very wide price range and several varieties with different properties.

Vinyl wallpapers are highly durable and are used where mechanical damage is possible. Acrylic - moisture resistant.

Non-woven non-woven coatings can withstand repeated painting. Fiberglass material is not afraid of fire. In a wide range of colors, photo wallpapers are presented that can change the interior space beyond recognition. Ceramic tiles are used for floors and walls. Used indoors and outdoors. Has high wear resistance. Due to the richness of textures and variety of designs, it is perfect for any interior. Allows you to emit stone, various types of wood, leather, fabric.

INTERESTING VIDEO

Due to the strength of this material, you can decorate the kitchen, hallway, bathroom. For its laying, a perfectly flat surface is required, which requires high-quality preparation of the concrete base. When decorating premises, thin sheathing boards, which are also called "lining", are often used. The wooden coating has good thermal insulation and is used for covering any premises, including saunas, attics, balconies, living rooms and utility rooms. In conditions of high humidity, plastic PVC panels are often used that imitate wood paneling. In terms of quality, they are inferior to natural materials, but this is offset by a lower price.

Many types of decorative plasters are widely used for finishing the walls of a frame house outside and inside buildings. The material is easy to apply and can hide difficult surface imperfections. The decoration creates interesting textures, imitating any kind of finishing materials. Glass-magnesium sheets have good refractory properties, are not afraid of water and have excellent adhesion to any kind of materials.

Decorative plates, in the form of stone, are widely used in interior decoration. They have the wear resistance of natural material and are very easy to use due to their flexibility and ductility.

Where to start the interior decoration of a frame house?

Interior finishing work should begin with a detailed plan. It is necessary to take into account the materials used, fasteners, tools. At the preparatory stage, all communications must be installed. The further sequence of work depends on the selected materials.

Interior decoration of a frame house with plasterboard sheets

INTERESTING VIDEO

Interior decoration

On the inside of the house, the walls do not need additional thermal insulation. All heaters are laid inside during the external processing of the walls.
Do not forget that water pipes and electrical wires fit into the walls. Pay special attention to the bathroom and toilet, as these places will have high humidity. Therefore, it is worth treating the walls with a special material that will protect them from water ingress.

Engineering systems

In frame houses, the entire engineering system is hidden in the walls. Electrical cables before laying must be placed in a metal hose.
The water supply system also requires special attention; it should be laid in a corrugated pipe, which is also additionally insulated.

Room design

Interior decoration

General construction work has been completed, engineering systems have been laid and checked, insulation has been installed. It's time for interior decoration. There are a great many ways. Such materials are used.

Drywall

Environmentally friendly, hardly combustible, drywall is affordable. The sequence of sheathing is as follows - facing of ceilings, walls, preparing them for painting, wallpaper, final finishing, installation of the floor. In modern projects, wallpaper for painting is popular. The sequence of installation of stairs, internal doors depends on the installation method. The advantage of drywall is perfectly smooth walls. Partitions are made from it in rooms, delimiting the zones of the room. Drywall is used in buildings with heating. Otherwise, in winter, it can burst, swell.

Wooden lining

Wood is an excellent environmentally friendly finishing raw material for a frame house. Conifers even retain the smell. Pine is the cheapest and most popular. The next most popular is alder. Larch, oak, ash are less often used because of the high cost.

Baths, saunas are sheathed with linden, aspen. The lining is varnished. After the first, second coating, the lining is sanded. The third layer is clean.

block house

The interior decoration of the block-house looks solid and modern. The front part is similar to a log, creates a resemblance to a classic wooden house. A good mounting system provides ease of installation, ventilation. This finish is appreciated by people who prefer folk style.

Plastering

Modern types of plaster enable designers to achieve excellent results in traditional ways, using modern materials. Before plastering, thermal insulation is laid, a layer of reinforcement, then plaster, which performs a protective and decorative function.

PVC panels

The material is easy to install, non-toxic, a wide variety of textures, colors, is not afraid of moisture. The downside is lack of prestige. Use for bathrooms, public places.

Kitchen finishing

The kitchen has a lot of cabinets. Some of them are hung on hooks. It is allowed to screw the screw into the frame of the building. For cabinets, a rail is pre-stuffed. The places of the frame are learned from the project. Sometimes fastening bars are installed at the stage of wall assembly.

Communications are hidden inside the walls, do not spoil the interior. The floor of the kitchen is leveled, then the flooring is laid. Choose parquet, laminate, tile. For walls, the best material is ceramic tiles. Usually part of the wall, the apron is tiled, the rest of the surface is painted, pasted over with wallpaper.

The paint is antimicrobial, forming a bactericidal film. Wallpapers are selected waterproof. The ceiling is finished with plasterboard, puttied, painted. Two-level ceilings with lamps at different levels are popular.

Bathroom finishing

The frame house does not restrict the installation of all modern amenities. It is believed that the bathroom is best placed on the first floor. Modern construction removes this limitation. Features of the frame structure must be taken into account when equipping the bathroom. The tree is able to absorb moisture and collapse. Before finishing the bathroom, the frame is treated with antiseptics. You need good waterproofing. Tile is the best material, mosaic is possible, moisture resistant laminate. From wood, larch, teak are used. There are a lot of materials than to finish a frame house. Designers often use a combination of different methods and materials to achieve great aesthetic results. You can visually add volume. Sometimes it is required to visually lighten the structure. The possibilities for decorating, for a flight of fancy are endless. The most nondescript building is transformed into an exquisite, luxurious home. The nice thing is that many finishing operations are do-it-yourself. Even without significant experience in construction.
Source: yar-doma.ru

Interior decoration of a frame house: features of work

After the completion of the construction of the house, both external and internal finishing work is required. The interior decoration of a frame house can be carried out using a wide variety of building materials, which today are presented in a wide range. Finishing the frame house inside allows you to give it a complete and residential look, and in order for the repair to be done with high quality, some features should be taken into account.

INTERESTING VIDEO

In the case of a new building, it is not recommended to start interior finishing work in all rooms at the same time, but to start from the furthest room from the front door. Repairs begin after sewer pipes, utilities and electrical wiring. The decoration of the room begins according to the “top-down” rule, that is, the ceiling is first tiled, then the walls and lastly the floor, with the exception of stretch ceilings. During repair work, it is necessary to cover the surfaces with a dense polyethylene film in order to avoid contamination. The speed of interior finishing work is influenced by several factors, which include the complexity of the repair, the planned budget, and the timing of delivery and purchase of materials. Basically, the timing of the repair depends on the qualifications and experience of the team of workers, and the turnkey repair allows not only to save material resources, but also to complete the work as soon as possible.

Choice of finishing materials

Today, modern manufacturers offer a large selection of finishing materials at affordable prices, which include:

Plasterboard sheets;
Wallpaper;
Ceramic tile;
Lining;
Plaster.

The interior finishing of a frame house includes rough and finish work. The rough finish includes the preparation of walls and surfaces, the elimination of any defects and irregularities, the floor screed, the removal of old coatings, and the installation of slopes. Fine finishing of the house includes finishing works, which include plastering walls with subsequent painting, wallpapering, flooring, ceiling finishing. The choice of facing materials depends on the taste preferences of the owners of the house, their financial capabilities, and the main condition is the creation of favorable conditions for a comfortable stay. Watching video

Without proper cladding, any house is just a box of little use for living. The quality of the interior decoration of a frame house will determine the comfort and style of your future home. Today we will analyze in detail the options for every taste and budget.

Before you start work, consider a few important points.

Do not start finishing in several rooms at once, move progressively, from one room to another.
To prevent repairs from dragging on for years, make a clear plan, each item of which is given time. Facing a small house takes from a month to three. The term depends on many factors: materials, complexity, the presence or absence of a professional team.
Pay special attention to the rough finish. If it is carried out poorly, then the end result is unlikely to be pleasing to the eye.
One of the features of the interior decoration of a wooden frame house is the strengthening of the walls in places next to which there are holes for window frames.

Work order

Work begins only after the electrical wiring and other engineering communications are laid.
Before giving the decoration of the house a finished appearance, a rough finish is carried out.
Always start in the room that is farthest from the entrance.
Before starting work, cover the surfaces with polyethylene - this will facilitate the subsequent cleaning of the house.
The principle according to which you will produce the cladding of each room is “from top to bottom”. This means that you should start from the ceiling, then switch to the walls and lay the floor last. However, there is one exception to this rule - stretch ceilings. If your choice fell on them, then mount the structure last.
Do not forget to purchase special equipment to protect the skin, and goggles that will protect your eyes from construction debris.
Necessary tools - building level, tape measure and spatula.

Rough finish

Rough finishing is no less important than finishing or finishing. It depends on it how warm the house will be, and how durable the repair will be.

Works include:

removal of old coatings;
ceiling screed;
laying a layer of insulation for walls;
wall cladding;
creation of a "rough" floor;
alignment of all surfaces that are planned to be faced;
slope installation.

Materials used

The construction market offers a huge selection of materials for rough and finish interior decoration of a wooden frame house. The main thing to focus on when choosing is the budget and the complexity of the work. Let's analyze the most popular options.

Finishing materials:

drywall;
OSB boards;
primer and plaster mixes.

OSB boards are considered the most progressive - they completely level the surface and are easy to install.

Finishing materials:

paper wallpaper;
liquid wallpaper;
lining wooden;
lining plastic;
ceramic tile;
decorative plaster;
glass-magnesium sheets;
flexible stone.

You can use any of the listed materials “solo”, or you can combine several - it all depends on your imagination. We will talk about the advantages and disadvantages of different types of materials for the rough and finish interior decoration of a frame house below.

Finishing options for a frame house

Drywall

Sheets of material are attached to metal profiles, which means that there is no need for preliminary alignment of the walls. Another important point is the ability to leave free space between the wall and drywall slabs. This creates freedom for the choice of insulation and the possibility of laying communications, including electrical ones. However, remember that if you decide to lay the wiring in this way, then it is placed in special corrugations that prevent fire. Many choose drywall also because, due to its low weight, it does not create additional load on the supporting structure.

Work order:

Before proceeding with the interior decoration of a frame house with drywall, mark up and, using self-tapping screws, fix the metal profile.
If provided, lay the walls with insulation.
Drywall is placed on the profile, and fastened with metal screws. Make sure that the hat "drowns" inside the sheet by at least a millimeter.
Fill the space between the sheets with putty, remove the excess and align the seams.
Take fine sandpaper and sand the surface.
Rough finishing is completed, now you can start finishing.

OSB

OSB boards are another common material for rough finishes. Their installation is similar to drywall sheets, with the only difference being that, due to the greater weight, a more secure fastening is required.

Work order:

The slabs are fastened to the wooden frame with nails in the form of a spiral at a distance of 15 cm.
If you are laying OSB on the floor, then this must be done perpendicular to the lags.
Before using a finishing material on top of the plates, go over them with fine-grained sandpaper and varnish them in three layers.

OSB boards are an excellent option for forming partitions in rooms, if necessary. The main difference between this material and drywall is its thickness, high density and strength. These qualities, depending on the goals and circumstances, can be assessed as an advantage or a disadvantage. If the curvature of the surfaces is so strong that the drywall can bend, then it is better to use OSB.

clapboard

Lining with clapboard is an environmentally friendly option for interior decoration of the walls of a frame house. In addition to an attractive appearance, you also get a particularly favorable indoor climate. In addition, the material has good sound insulation and excellent heat retention.

Kinds:

"Extra" - a variety without any defects, with an impeccably even and smooth surface.
"A" - small chips and blackouts in the lamellas are acceptable.
"B" - cracks and knots may be present.
"C" - the presence of blackouts, resin bags, cracks, knots over the entire surface is allowed.

Paradoxically, it has recently become fashionable to choose exactly the “C” variety. Such lining has a low cost and perfectly imitates the vintage style.

Work order:

Cover the slats with special bioprotective compounds against fungus and mold.
If color is fundamentally important, you want to make the coating darker or lighter, then cover with wood stain or other special substances to create the desired tone for wood materials.
The lining can be mounted on OSB boards, that is, immediately on the finished wall.
There are many options for fastening this material - with nails, staples, kleimers, etc. The best of them will be the one that will cause less damage to the material.

timber imitation

This material is considered a subspecies of lining. The main difference is the creation of the effect of laying logs. The category of “lumber imitation” includes PVC, which is sometimes called “plastic lining”, since wood is easily imitated with this material. The interior decoration of a frame house with an imitation of timber will cost less, but PVC lamellas are devoid of the advantages of wood.

Plaster and wallpaper

Plaster and wallpaper are simple materials in terms of work technique. Often, those who decide to do home improvement with their own hands choose them. Finishing plaster refers to the so-called decorative mixture, we will talk about it later, but now let's focus on wallpaper.

Wallpaper types:

Paper. For the interior decoration of the walls of a frame house, this is not the best solution - they are exposed to moisture, burn easily and do not differ in durability. However, they are often used as a temporary option, allowing you to give the walls an aesthetically pleasing look and save money.
Vinyl and acrylic. Wallpapers similar in their characteristics that can be used for decoration. They are durable, resistant to mechanical damage and moisture resistant.
Fiberglass. A great option, both for independent use and for painting. These are the strongest and most durable of all types of wallpaper.
Wallpaper. Today they are used infrequently, but are indispensable for some design decisions.

Decorative plaster

Once this material was considered "elite", but today it can be afforded with any budget. Using the finishing cladding with decorative plaster, you can hide minor flaws in the rough finish, give the walls an interesting texture. In construction stores, you can purchase special spatulas to form the structure of the wall, with their help even a non-professional can use interesting design solutions.

The advantage of the material is its resistance to moisture, fire and odors. That is why plaster is often used in the design of the kitchen.

Tile installation

Ceramic tiles are durable and aesthetically pleasing, but require a perfectly flat surface. If you decide to tile the walls, it is advisable to use a special reinforced drywall designed for installing tiles as a rough finish. Today you can find a lot of stylistic solutions - natural stone, brick, wood, mosaic and much more. It is also worth noting that this finishing option is not budgetary and will require significant investments.

Glass-magnesium sheets

Another, yet not so common, version of the rough interior decoration of a frame house. This material is distinguished by its special strength, flexibility and high performance. It is made of oxide and magnesium chloride, covered with fiberglass on top. Glass-magnesium sheets are very light, therefore, reinforced profiles are not required during installation. They are fastened with self-tapping screws, before finishing they are covered with a primer or plaster.

flexible stone

The material is made from sandstone, which is applied to a flexible fiberglass substrate. The main advantage is the possibility of installation in hard-to-reach places. The advantages of a flexible stone include such qualities as the ability to pass air, moisture resistance, minimum weight. Often it is used in rooms with high humidity - kitchens and bathrooms. Fastening is carried out using special glue on a leveled surface.

Categories

Popular