Finishing the fireplace: photo ideas, methods. How to finish a fireplace: plaster, tiling, stone Natural stone for fireplace lining

Facing the fireplace with decorative stone is quite common nowadays. First, it's cheaper.
In terms of parameters, decorative elements are not inferior to natural ones. Facing this element and this article will be devoted.
Facing, this is the final work, which can ruin everything, so it must be done correctly. You can watch a video on the implementation of this work.
Instructions will be given on the rules for conducting work.

First you should look at the photo and choose the desired design. This will determine the color and size of the elements.
After that, you make their purchase and you can get to work. The fireplace can be active or a portal is made.
Our instructions apply to both options. Where required we will make reservations

Surface preparation

Facing fireplaces with decorative stone begins with this work. We need to make a base for installation.
It will also determine the quality of bonding surfaces. If this is not done correctly, then the durability of the structure will be significantly reduced.
For the portal, it will be enough to clean the plane from the previous coating and cover it with a primer.
For the current design, things are a little different:

• We completely clean the surface from the previous coating. To do this, use a metal brush.
  The old tiles and plaster should also be removed. You can also use a chisel. But the surface must be completely clean;
• Now we need to deepen the seams. This will largely determine the quality of the bond.
  They should be deepened by about one cm. For this, we use a chisel and a hammer;
• For a high-quality connection of the solution and the wall, we need to stretch the mesh onto a plane. To do this, you need to drive nails into the seam.
  If the masonry is strong, then we make holes with a puncher and then screw in the screws;
• We carry out the coating of the plane with a primer. It will provide a high-quality connection of materials.
  To do this, use a brush or spray gun;
• After that, we cut the mesh to the desired size and hang it. Just do not forget to wear washers on hats. They don't let the grid subside.
• We inspect and determine the level of application of the cladding. To do this, we use a plumb line and a building level.
  After completing the work, the fireplace must have the correct geometric shape. We install beacons to determine the height.

Solution preparation

Decorative stone for facing fireplaces is best, of course, laid on the mortar from which the masonry was made. It will most qualitatively connect and increase durability.
At this time, there are generally three types of solution, from which you can choose exactly what you need.

Clay mortar

This mixture is best suited for. It fully meets all the parameters.
It will withstand high temperatures and is resistant to temperature changes, but it is much more difficult to cook it.
So:

• We start by determining the fat content of clay. The proportion with sand will also depend on this.
  This is one of the most important parameters. We make a dozen balls with different proportions. And let them dry completely.

Attention: When you make balls, do not forget to number them and write down what proportion was used in each individual case.

• After complete drying, we let them on a hard surface from a height of one meter. One that will not break or deform and will have the correct proportion;
• Now we take the clay and pass it through a sieve. We need to remove the weight of rubbish and stones.
  The mixture must be clean;
• Now we put it in a container and fill it with water. Leave it like this for a day.
  The material should become plastic and sour. Dial the desired viscosity;
• After a day, we begin to add sand in the desired proportion and knead the mixture. Add water if required.
  Should be the viscosity of thick sour cream. We knead all the lumps with our hands;
• Now we need to make the solution homogeneous. For this, a drill with a nozzle is best suited.
  It is she who will make the whole mass completely homogeneous;

Attention: If you use solid fuel in the fireplace, then it is worth adding about 10 percent of fireclay powder to the solution. It will allow the masonry to withstand higher temperatures.

cement mortar

Such a solution is also used for laying a fireplace. Only if you are using solid fuel, then it will not be as durable as in the clay mortar issue.
So:

• First, we fill in the sand and then add cement to it in the right proportion;
• Mix dry and achieve an even distribution of the components;
• Now add water in the right amount and mix at the same time;
• We bring the composition to homogeneity using a drill with a nozzle.

Dry mix solution

A decorative stone for facing the fireplace is also placed on a mortar from a dry mixture. Its price is quite different, but it is perfect for attaching elements to the portal.
The sequence of its preparation is as follows:

• It is best to pass the dry mixture through a sieve before use, while separating all debris;
• After that, you need to pour it into a container. For this, it is best to use a plastic paint bucket.
  It has an edge without edges and a flat bottom. In it, you can best knead;
• Add water and stir at the same time. Complete homogeneity can be achieved with a drill with a hen. We bring the mixture to a state of thick sour cream.

Making a fireplace mantel

Now, after proper preparation of the plane and the solution made, you can proceed to. There are rules to follow for this.

All work is done entirely by hand:

• Before laying the parts, spray on the mounting plane. To do this, we make the solution more liquid, at the level of liquid sour cream, spray it onto the attachment plane with a ladle.
  This work is not done for finishing portals;
• Facing fireplaces with decorative stone starts from the bottom row and from the corner and then moves up;

Attention: Never mount on mortar without first trying on the elements. Before installation, it is necessary to fully fit all the details and then make the mount.

• First, all the details should be laid out on the floor in full size. We make a pattern.
  At the bottom there should be elements that are thicker;
• We take a corner element and try it on a plane. We immediately try on others from the row.
  If necessary, we do the fitting of the part with the help of a grinder and a cutting wheel;
• After a quality fit, we take a notched trowel and apply the solution to the surface of the element;
• Each row of laying should be checked with a level. Configurations should not be broken;

• We press it into place of installation and at the same time make a little rotational movement. The part should sit on the solution and no pores with air should remain.
  The mixture should come out of the seams;
• There are two installation methods. It is suture and seamless.
  The second one is more simple. When applying the first option, you will need to observe the size of the seam.
  This is achieved by using plastic crosses or wedges;

• After fixing, wait a bit until the mixture dries and remove the excess. The seams should be walked with the corner of the spatula and cleaned;
• We are waiting for the complete drying of the solution and fill the seams. After letting it dry a little, wipe them with a rag;
• After complete facing of the surface, a protective coating is applied. For this, wax mixtures are best suited.
  They will protect the surface for a long time.

20.04.2017
2280
Pechnik (Moscow)

If you are looking for the optimal finishing material for your fireplace installation and want to choose the highest quality, high strength and at the same time relatively affordable, we recommend that you read this article.

Today, it is the stone for facing the fireplace that is very popular due to its unique features, characteristics and the presence of other undeniable advantages.

Advantages and features of natural coatings

Natural stone for a fireplace has a number of its advantages and features, which include:

1. Environmental friendliness. This category of coatings is distinguished by its environmental friendliness. This is due to the presence of exclusively natural and natural components in the composition. Such materials tolerate strong heat, sudden temperature changes, and have a low percentage of water absorption. When heated, the natural coating does not melt and does not emit harmful substances and other decomposition products into the air;
2. Strength. Choosing a natural stone for finishing the portal, you prefer high strength. Such lining does not break off, does not scratch or deform, which makes it reliable and durable. A smooth and even coating, as well as low porosity, does not allow dirt to penetrate deep into the pores, and care is extremely simple;
3. Durability. The facing stone for a fireplace differs in the durability. Due to its environmental friendliness, durability and proper care, such a coating will not require replacement for a sufficiently long period of operation;
4. High quality. Facing stone for fireplaces and stoves is of high quality due to special pre-treatment. To do this, it goes through several firings and, at the last stage, is impregnated and coated with a special composition;
5. Large selection of invoices. Stones for a fireplace are natural, have many different colors and textures. Their surface can be either slightly matte or rough, or perfectly smooth and glossy. Colors vary depending on the selected breed - it can be both light brown and bright red, combined surfaces with different patterns or completely plain.

Important: despite its main advantages, naturalstone for fireplacesIt also has significant drawbacks. These include a rather high cost and the need for periodic surface treatment of the coating with special varnish compositions and impregnations, the price of which is also quite high.

Photos of fireplace portals made of natural stone, you can view here:

The main advantages of artificial turf

The stone for finishing the fireplace can be not only natural, but also artificial. This coating has the following advantages:

1. Easy finishing work. You can do the lining of the fireplace portal with artificial stone with your own hands, which cannot be said about natural materials, for which you need to have not only a special tool, but also experience. This coating in its appearance resembles a simple ceramic tile or tile. The method of fixing it on the surface is similar. It is possible to lay such a coating in the shortest possible time, and even without experience;
2. Affordable cost. Artificial materials are distinguished by their affordable cost. However, they are not much inferior to natural facings. Unlike them, the composition includes various components, as well as artificially added impurities;
3. Large selection of colors and surfaces. A finishing stone for a fireplace can have a different color design, due to the dyes included in the composition. The surface of the product is both a smooth and glossy structure and a rough refrain surface;
4. Versatility. The stone facing for fireplaces is universal. It tolerates sudden changes in temperature, strong heating, does not melt or deform. When heated, it does not emit harmful substances. Differs in the low porosity and does not absorb moisture;
5. Low weight. Unlike natural coatings, which have a fairly large weight, this facing material is quite low. This allows you to use it for any type of structures and hearths. When finishing a suspended or built-in portal, the stone does not exert a significant load on the walls of the house.

Important: the disadvantages of artificial coatings include the possibility of slight darkening in areas of particularly strong and intense heating, as well as where fire touches this material. Often quite rough and roughstone texture for fireplace, makes the care and elimination of various contaminants very difficult and not simple.

You can learn more about the types and features of such coverage by watching the video in this article.

The main types of coatings

Natural stone for facing the fireplace, as well as artificial, is divided into main varieties. Each of which has its own characteristics, advantages, disadvantages and characteristics.

What is natural stone

The most expensive floor stone for a fireplace is usually natural. However, depending on your personal wishes, preferences and possibilities, you can choose one of the following natural finishes:

Varieties of artificial stone

Artificial turf, the price of which is one of the most affordable, is divided into the following varieties:

Tip: in order to perform finishing work efficiently and professionally, a pre-compiled or foundinstruction, in which you can learn how to veneer the fireplace portal step by step.

A stone for facing a fireplace, regardless of its nature and category, will allow you to perform a high-quality finish. Such a coating is guaranteed to be reliable, durable, safe for health and environmentally friendly.

The hearth decorates any house. It is always nice to wrap yourself in a blanket, sitting in front of your fireplace, and enjoy the flashes of the flames of the hearth.

In modern interiors, decorative fireplaces made of stone are increasingly being installed, using artificial materials to simplify finishing work. After all, the use of natural stone obliges to create a foundation for the structure and carry out complex construction manipulations.

In this article, you will learn about the advantages of artificial stones, read the recommendations for choosing the right material and get all the information you need to finish the fireplace with your own hands. In the photographs you can clearly see the varieties of decorative stone finishes and finished lined fireplaces.

Advantages of decorative stones

Artificial stones are used for finishing electric and wood-burning fireplaces, gas structures, bio-fireplaces and fireplace stoves. Due to the achievement of maximum similarity of designs, the decoration of the fireplace with decorative stone complements the overall style of the interior.

Such facing stones have a number of advantages:

• high refractory performance;
• retain their natural color and appearance for a long time.
• convenience when decorating due to the lightness of the material;
• a variety of colors and textures allow you to select stones for fireplaces in the right style;
• low cost compared to natural stone;
• easy self-use, convenient cutting and stacking;
• does not emit harmful odors, as it refers to environmentally friendly materials, does not contain impurities and toxic reagents.

Artificial stone is made from cement with the addition of expanded clay, pumice or fillers. Dyes are added to give the necessary colors to the material.

• Thanks to these technologies, artificial stones weigh about half as much as natural ones.
• At a low cost, the external texture of the material differs little from natural stones, sometimes it is difficult to distinguish them from each other.
• The appearance of the material repeats the natural shape of the cobblestones. They come in the form of chipped, sawn rubble stones.

According to individual orders of customers, completely unusual shapes and colors are made.

To clad a stone fireplace with your own hands, you need to purchase the appropriate materials.

Choosing a decorative one from the whole variety, you should approach this issue creatively, decide in advance on the design style of your design. It is important to keep the following tips in mind:

• Do not chase the goods of foreign firms. Most often, Russian counterparts are of the best quality and at the same time have a low cost.
• Finishing the fireplace with stone is done using heat-resistant products. Before purchasing finishing stones, consider the heat-resistant characteristics, depending on the type of hearth used. If you decide to use non-heat-resistant decorative stones for cladding, then toxic substances may be released when heated.
• Familiarize yourself with the quality certificates for products, such documents will guarantee compliance with the specified parameters. If you are refused to provide certificates, this indicates the questionable quality of the product. It is possible that the production was carried out using harmful components.
• Purchase material from well-known manufacturing companies that have been working for a long time and have established themselves in this industry.
• Quality products on cardboard packaging have a brand logo and manufacturer's coordinates.
• Before buying, pay attention to the appearance of the artificial stone, the presence of defects in the form of cracks or chips, as well as other signs of marriage, is unacceptable.
• Pay attention to the date of manufacture of the stone, since the process of hardening of the material is carried out within a month after release. Only after this time the material acquires its strength.

In addition to decorative stones, you will need to stock up

• heat-resistant glue;
• water-repellent impregnations with protective properties;
• grout;
• a cleaner designed to remove cement residues from the surface;
• specialized varnish for surface cladding, creating the effect of wet stone.

For lining the fireplace, a special adhesive composition is used. It must be chosen taking into account the main surface: a high-quality connection can only be in the case when the composition of the decorative stone coincides with the base of the adhesive.

• For example, gypsum decorative stone is glued together with gypsum glue, while cement stone requires a cement adhesive.

Moreover, if the main surface has depressions, then mastic is used. She can fill in all the imperfections with high quality.

Preparatory work before cladding

After choosing the facing material, you can proceed to the preparatory work. For preliminary preparation, decide on the surface on which you will lay the artificial stone.

• These works can only be carried out at an air temperature of more than 5 0 C, since low temperatures affect the quality of bonding surfaces.

To prevent contamination of the elements, the stone should be faced from top to bottom. Thus, the work performed will have a neat and tidy appearance.

To cut artificial stone details, use a hacksaw with fine teeth, in which case the edge will be smooth and beautiful.

• When used as a basis for a wooden surface, it is pre-coated with waterproofing.

If the fireplace is made of metal or concrete, waterproofing is not performed.

Please note! In case of serious irregularities of the concrete or brick walls of the fireplace, it is necessary to apply plaster.

• A plaster mesh is attached to the base with special fasteners.
• Plaster is applied on top of the grid and the layer is completely dry.

If the thickness of the materials has discrepancies or the shape of the decorative stone has an uneven structure, then it is worth laying them in a chaotic manner. So the overall composition will look natural and believable.

Required Tools

Before carrying out construction work, prepare the appropriate tool:

In addition to the tools indicated in the photo, it is desirable to have:

• self-tapping screws or nails for mounting auxiliary materials;
• spray gun or brush for wetting the surface of the base before applying the adhesive;
• building trowels;
• hammer ordinary and rubber;
• grinder with a disk on a stone;
• screwdriver and drill;
• even wooden bars as guide racks;
• a container in which the solution is stirred.

Stone cladding

Finishing the fireplace with a decorative stone is shown in the photo, we will analyze the main stages of facing work and focus on the important nuances of the process itself.

The entire base surface of the fireplace portal is cleaned. It is important to pay special attention to this, because the result of all work depends on the preparation of the foundation.

If the portal is brick, it is cleaned, removing excess mortar or uneven seams. With a sharp and durable metal object, make a recess in the seams between the bricks.

• If the main surface is uneven, it is leveled with plaster or cement mortar, applying it to the grid.

Before finishing work, make a drawing and lay out all the details on the floor. Before dry laying, try on one row and check the configuration.

• When using a tile that has an irregular shape, it is necessary to mark it from the wrong side, the numbers of neighboring parts are written on the edges.

It is important to know that the lined fireplace will turn out to be even if the finishing work begins with the strengthening of thick stones. They will become a guideline for applying glue under thin masonry details.

• When laying stone tiles, take them from different boxes to evenly distribute the pattern, as they may differ in color and thickness from each other.

If possible, make seams between tiles of the same width so that the pattern matches in the future.

• When lining the fireplace with seamless masonry, firmly press all the details to each other.

If you want to veneer "under the brick" or using rectangular parts, follow the verticality of the corners. Accurately control the connection of horizontal and vertical planes, maintaining a 90 degree angle.

• To do this, you can use a special template on which the thickness of the seams and the intersection of perpendicular lines are marked.

The finishing process always starts from the bottom corner. After finishing the facing of the corner surface, they proceed to the upper horizontal row. Further, the main work is carried out, which is carried out from top to bottom.

• After finishing work, you need to withstand at least a day until the glue dries completely, then you can proceed to rubbing the seams.

Important! Pre-check the quality of the grout on the cut of the decorative stone - whether it leaves marks on it.

After the surface of the entire structure has dried, it is treated with a special fire-resistant hydrophobic composition. Thus, a protective film is created that does not allow moisture to pass through and preserves the decorative stone during deformation or external impact on the fireplace. Dust is easily removed from such a surface. Also, the protective film preserves the structure of the artificial stone during temperature changes.

It is desirable to trim the front and side of the portal with a decorative stone. For the upper part, choose solid planes from ready-made slabs made of natural or artificial stone.

DIY decorative stones

Having little experience in construction work, you can independently make facing stones of the required size and color.

To do this, use silicone molds into which a solution of cement, sand and dyes is poured.

In accordance with some technologies, the cement mixture is replaced by alabaster. At the same time, all the constituent components are immediately mixed, diluted with water to the required consistency and poured into molds.

In the forms, the material must completely harden, only then can it be used to decorate the fireplace.

Finishing the fireplace with decorative stones is available for any person. At first glance, it seems that this is very difficult and time-consuming, although it is not. If something doesn't work out for you in the process, remember that you can always redo it.

The main thing is to choose the right parts and be creative in the process, following the recommendations. In this case, the fireplace will fill the beauty and charm of the hearth, while delighting your entire family for many years.

A home fireplace in itself is a wonderful addition to your home decor. Of course, in modern apartments of high-rise buildings there is no way to install a real wood-burning fireplace, but it is quite possible to replace it with an electric one.

Happy owners of country houses are in a better situation. The design of private houses makes it possible to install both a wood-burning fireplace and a gas fireplace with an imitation of a fire flame from firewood. In order to best fit it into the interior of the house, to harmonize with the style of the room in which it is located, you can make a stone finish.

For this purpose, both natural and artificial materials are used. Both of them have their advantages and disadvantages. Entrust the facing of the fireplace with decorative stone to professionals in their field, this guarantees a quality result and safety for the residents of the house.

Finishing the fireplace with natural stone

For finishing a fireplace with natural stone, such types are most often used as: marble, granite, shell rock, sandstone, soapstone, granite ceramics. Each of them has its own characteristics of operation, texture, natural pattern. If you are not limited in funds and want to add style, nobility and elegance to your home, pay attention to this option for finishing fireplaces.

Marble for facing the fireplace

This noble natural stone is considered the most common material for finishing fireplaces. With a wide range of greys, greens, whites, pinks, blacks and browns, you shouldn't have any trouble choosing. The pattern on the cut depends on the structure of the stone and the way it was cut. Marble can be recognized by the characteristic shades of inclusions, stripes and veins. Various processing methods allow you to get a different texture of the material: aged, smooth, glossy.

Marble goes well with any other materials used in construction. The most profitable option for using stone in decoration is ground marble. Almost all types of this rock are suitable for grinding into crumbs of various fractions, from which a mosaic or filler for finishing materials is produced. The most popular types of marble are black and white, plain without interspersed with other shades.

Finishing the fireplace with granite

This is the most durable and reliable type of natural stone. In addition, it is durable, has an attractive appearance. Granite fireplace harmoniously fits into any interior. The texture of the material has a uniform grain size and bright patterns that allow you to accurately guess it is granite.

The shade of the stone directly depends on the area of ​​extraction. It is because of its durability that granite has been popular for many centuries. History confirms some facts about the use of granite fireplaces in manors and castles that are more than 100 years old. In addition, it is worth noting that the material is processed without much difficulty, allowing various design ideas to be translated into reality. The combination of granite with mosaics and various tiles looks quite impressive.

Advantages of marble and granite fireplaces:

Soapstone cladding

This is a modern finishing material that has gained popularity relatively recently. The layered structure guarantees a high level of conductivity and heat retention (accumulates it on the surface). In ancient times, people believed that soapstone could give a person strength and health, because it radiates heat that matches that of a human. Among the physical properties of the stone, it is worth noting its special density and low thermal expansion. These qualities allow it to be used for lining fireplaces.

Finishing the fireplace with sandstone

This natural material is very often used for finishing fireplaces, as it has the ability to withstand high temperatures. In addition, it is durable and has a long service life. Its use makes it possible to embody original design ideas.

The advantage of sandstone lies in the ease of processing and cutting. Also, the material has a wide selection of shades, which allows you to create unique paintings. Sandstone combines environmental friendliness, decorativeness, practicality, as well as affordable cost.

Granitoceramics

This is a decorative stone for facing the fireplace, which is made from natural clay. The appearance of the finished product resembles the structure and color of marble or granite. The main difference from ceramic tiles is the basis for production. For the manufacture of granite ceramics, clay is used, which has increased strength. It is this component that ensures the reliability and strength of the material, resistance to mechanical stress, resistance to high temperatures. During long-term operation, granite ceramics does not lose its original appearance, retaining its luster and color.

Shell rock fireplace

This is a unique natural material that helps to create a unique decoration of the fireplace with decorative stone. The porous structure of the stone provides a high level of thermal insulation, resistance to temperature fluctuations. The shell rock contains the remains of sea shells and mollusks, fossilized many years ago. In order to create the desired shape from the stone, it must be polished.

The shell rock has hygroscopicity and ease of processing. The stone has an airy porous structure, thanks to which it absorbs moisture, and then releases it to the surface. In addition, it is these pores that give the shell rock special strength. Among the decorative features of the structure of the material, it is worth noting the originality of the patterns.

For lining fireplaces with natural stone, white and yellow shades of shell rock, which have additional shades, are most often used. The material allows you to cut out various details from it to design a decoration item.

Note. Finishing fireplaces with natural stone is suitable for those who are satisfied with the low heat capacity of the surface of the material.

When choosing a finishing material, please note that:

Advantages of natural stone for facing fireplaces:

• The uniqueness of texture, pattern and shades;
• Powerful positive energy;
• Resistant to temperature fluctuations and high levels of humidity;
• Can be used on any surface;
• Durability;
• Strength and reliability;
• Environmental friendliness;
• Attractive appearance;

Disadvantages of natural stone:

• Tarnishing of marble and the formation of a mesh on the surface after a certain period of operation;
• High cost associated with mining methods;
• Emission of natural radioactive background by granite;
• Abrasion of sandstone;
• The shell rock accumulates soot, dirt and dust.

If you look at these shortcomings from the other side, then they do not matter much, compared with the merits of natural materials, and their beauty.

Design types of home fireplaces

• Corner ones are suitable for installation in small rooms, take up little space;
• Wall options are placed in the center of the room, have a rather overall design, are more suitable for large rooms.
• The islands have low sides and an internal firebox, above which an exhaust hood is mounted to remove smoke;
• Built-in have a chimney and masonry walls, which in turn requires the use of a large amount of material.

Fireplace cladding with artificial stone

Modern technologies make it possible to create facing materials that are in no way inferior in terms of performance to natural ones, and in some cases even surpass them. If you want to finish the fireplace with stone, but do not have enough funds for natural material, turn your attention to imitation. Convenience and ease of use make it possible to realize bold ideas.

Advantages of artificial stone for facing the fireplace:

• Ease of processing, the ability to create any shape and size of elements;
• Light weight;
• Possibility of combination with other materials (ceramics, metal, glass);
• Creating an imitation of natural stone finishes.
• Maintaining the quality of the finish;
• Aesthetic appearance.

Results

For residents of the city who live in apartments of high-rise buildings, who at the same time want to have a hearth in the form of a fireplace in the living room, there is a great alternative - facing false fireplaces with artificial stone. These are simple structures that do not require complex installation, chimney arrangement, and heat-resistant walls. Special heating elements act as an imitation of firewood. The installation of a biofireplace can be done near, which eliminates the need for an additional heat source.

This modern, high-quality and environmentally friendly material, which is widely used for facade cladding.

It completely copies the texture of natural stone.

Series of artificial decorative stone White Hills are presented in collections, which are divided into:

• invoice;
• form;
• mind;
• sizes.

Building collections is a creative process.

While working on the details, specialists create tiny cracks, gouges and other effects of natural impact on the surface. This makes the products aesthetically complete and gives additional respectability to buildings that are lined with stone.

The use of modern equipment and the accumulated experience of specialists allow us to produce products with high technical characteristics.

Advantages of an artificial decorative stone in comparison with a natural analog.

Main criteria:

Light weight

Artificial stone weighs 1.5 times less than natural stone. Depending on the type, the weight varies from 16 to 50 kg / m 2. Such material reduces the load on the facade and foundation of the building. White Hills stone is also used in the reconstruction of dilapidated and old buildings.

• Democratic price. The cost of stone is lower than other facing materials (natural stone, clinker bricks, tiles, etc.).

The size of the decorative stone has certain standards

If it is necessary to dock products with other elements, then the size can be easily changed by cutting off the unnecessary part with the usual “grinder”.

Variety of colors

A certain color is indicated by the corresponding coding in the collection article. This diversity allows each consumer to choose the most suitable option for themselves within the same collection. Picking up the same natural stone exactly in tone is a rather difficult task.

Easy installation process

Laying decorative stone is easier than a natural counterpart. The wall does not need to be further strengthened. In terms of shape, White Hills products are tiles that are flat on the back. To level natural stone, you need to use special equipment, which will further increase installation costs.

• Environmental friendliness

  Artificial stone is an environmentally friendly material. It is devoid of harmful properties, unlike some rocks of sandstone, marble and granite, which have a natural background of radiation. This limits their scope depending on the category. White Hills products only externally imitate granite and do not require special documentation on the degree of background radiation.

  Corner elements

  Corner elements are present in each of the stone collections. They simplify the installation process and visually emphasize the integrity of the stone façade. To obtain corner elements from natural stone, a lot of investment is required. Due to the complexity of production, the price can be up to 1500 rubles per 1 piece.

  Strength

  White Hills artificial stone is stronger than some types of natural stone. For example, travertine and sandstone have a porous structure. The strength and frost resistance of such rocks is very low, so they are used mainly in southern countries. Artificial stone in its composition is not a porous material. Imitating travertine or sandstone, it does not collapse in winter. The material can be used in regions with a harsh climate.