Wood phone stands. Do-it-yourself wooden phone stand. Unusual coasters from simple things
Have you purchased a modern gadget and now want to make a stand? There are many techniques and methods that you can use to make a phone stand. Stylish little things can not only decorate the interior, but also make using the phone comfortable. In this article, we'll show you how to do it.
The easiest way to make a stand out of cardboard. To do this, cut a sheet of cardboard into several sheets of the same size. Suitable multilayer cardboard with corrugation inside. Glue the sheets with PVA glue. Let the glue dry. Draw a detail drawing on a thick cardboard base. This will be the figured leg for the stand. Using a utility knife, carefully cut the leg along the marks. Cut out another such piece. Cut out a circle from the remnants of a thick base, it will serve as an additional support. Cut a rectangle on the side of the leg. It will be the basis for the holder. Make a rectangle equal to the rectangular hole. Insert the part into the holes. Thus, you will connect the two legs together. Make axes for a circle from wooden rods. Make two holes in the legs and insert the axles there. Before that, put a circle on the rods. Before assembling the stand, it can be painted or pasted over with newspapers.
It happens that in some places there is not always a stable connection, in my case, the Beeline operator, since the tower is far away and nearby trees interfere with calmly transmitting the signal. I didn’t want to make any antenna for the phone, I came up with a simpler one, this is a phone stand that could be placed in the place where the connection is stable and does not depend on weather conditions. And about how to make a stand for the phone, I will tell you in this article.
As in any other homemade product, we need to decide on the necessary materials.
In order to make this stand you will need:
* Parquet.
* Board width 8cm.
* Epoxy adhesive.
* Threads, matches.
* Black felt.
* Hacksaw for metal.
* Drill and drills for it with a diameter of 3 and 6 mm.
* Coarse and fine-grained sandpaper.
* Screw length 55mm.
That's all the materials that we need, which is not hard to get, and if there is no parquet, then any strong board will do.
Now you can proceed to the gradual manufacture of the stand.
Step one.
The first step is to determine the dimensions of the future stand, for this we measure the dimensions of the phone that we want to install in the stand in the future, and do not forget to measure the thickness.
In my case, the thickness of the phone turned out to be quite large for the current time, after all, 1.5 cm is not small for a phone in 2017, but all this taking into account the fact that the phone has a protective bumper.
For convenience, we make a drawing on paper or in a program, as I did.
Step two.
After you have decided on the size of the stand, you can take the tools and cut out the main part. The basis in the stand is its so-called back, the dimensions of which are 8 * 9 cm. We take the thickness of the base 5 mm, no more and no less, because we don’t want the stand to be heavy or too fragile due to lack of thickness. To do this, I sawed across an already sawn board 8 * 9, reducing the thickness from 18 to 5 mm.
Now you need to drill a hole for attaching the stand to the wall, first drill with a 3mm drill, then 6mm, but not through, in order to hide the screw head. Then we round the corners with sandpaper.
Step three.
When the base is ready, you can start making legs that, with their design, will not allow the phone to fall.
To make paws, as it seemed to me, is best from the parquet that I found in my garage.
At first it was conceived so that the paws were composite, that is, assembled from two parts.
But due to the loss of strength with such a connection, I decided to make them solid. The result is such a foot in the form of the letter G.
There are three such paws in my design.
Step four.
At first, I did not attach much importance to the appearance, but in the course of manufacturing I realized that all sharp edges needed to be rounded off, which I did.
It is best to round sharp edges with coarse-grained sandpaper. Upon reaching the desired result, we grind with a finer grit to remove all teases.
Also, do not forget to sand the main part, since the surface of contact with the phone should be even.
Step five.
After all the component parts are sanded, you can proceed to fixing them to the base.
For these purposes, epoxy glue is best suited, which I have tested repeatedly and has proven to be high-strength.
Stir with matches one to one the right amount of epoxy glue and smear the places where the paws will be installed.
Epoxy glue dries for a long time, but holding the glued parts with your hands for a long time is simply not enough patience. Without thinking twice, I decided that the easiest way to fasten such a design with thread and matches, wrapping a dozen turns around its edges. Due to the large number of turns of thread, everything is held securely, and most importantly, the parts are pressed quite tightly.
We first glue the lower foot in the middle, and then the two side ones.
I had to tinker a little with the side ones, in this case it is better to ask a friend to help, since two hands were clearly not enough to hold two parts, and also wrap it all around with a thread.
Leave everything to dry completely.
Step six.
The epoxy glue has dried up and despite the fact that the width of the touching plane is only 5 mm, the paws hold very tightly.
Stand- a useful and convenient thing in everyday life. For example, phones or tablets, which have become an integral part of our daily lives, are a bit inconvenient to use in stationary conditions. If you do not have a branded or suitable case that can secure the gadget in an inclined position, then you will have to hold it with your hands. This is inconvenient when watching a movie for a long time, while eating or reading for a long time.
The best solution to this problem may be to purchase a stand specially designed for this. But, sometimes, we need it right now, or we simply feel sorry for the money for a seemingly temporary thing. In this case, you can make a stand yourself from improvised means. It does not take much time! A couple of minutes and you can comfortably sit in front of the screen of your gadget, while freeing your hands.
In this article, we will primarily rely on phone stand options, but they can also be slightly upgraded and used for tablets, books, even pictures or plates. It all depends on your imagination. But if she sleeps, then there is nothing wrong with that. The options proposed in the article are discussed in detail, and it will not be difficult for you to slightly increase the dimensions specifically for the thing for which you are making a stand.
Handy materials to help
You can make a stand yourself from improvised materials. Almost any material that you have at home is suitable for this. It could be:
- wire
- cardboard
- cardboard box
- fabric and padding
- bottle
- wood
- paper
- the pencils
- constructor
- stationery holders
- unwanted plastic cards
- old cassette
Only your imagination can limit your choice. Of course, the stores offer a huge selection of products in this category. However, making the holder yourself has a number of undeniable advantages:
- Rapidity. Sometimes a stand is needed as soon as possible, and there is no time to go to the store to buy it.
- Cheap or free. You can make a holder from what you already have in your home.
- Originality. With your own hands you will create a truly unique product.
Pencil phone stand
In order to assemble this design, you will need:
- 6 pencils
- 4 rubber bands
Despite the intricate appearance, this design is assembled very simply. The bottom line is that two pencils are fastened at the ends with an elastic band, and the third pencil is pushed between the turns of the elastic band. The result is a geometric figure - a tetrahedron. If you still have questions about how to make this version of the stand, then use the example below.
The figure clearly shows how the pencils are held together.
To avoid slipping and to make the stand more stable, use pencils with erasers on the ends.
Paper clip phone stand
The most economical and simple version of the stand, to create which you only need a paper clip.
To do this, you need to bend it into the same shape as in the figure.
This design will hold the phone without any problems.
Plastic card phone holder
For this, any unnecessary plastic card will do. Just fold it along the short side, stepping back from the edge of about 1 cm, and bend the rest in the opposite direction exactly in half. You will get it as shown in the picture.
Stand for phone or tablet made of cardboard
Cardboard- an excellent material that is widely used for various homemade "things". Probably, many people have a cardboard box or an unnecessary sheet of cardboard at home. It is worth trying to use it to create a stand.
For this you will need:
- cardboard
- scissors
From a sheet of cardboard folded in half, cut a strip measuring 10 by 10 cm. Then draw the figure shown in the figure on it and cut it out along the contour.
You will get a comfortable and stable stand that you can carry with you.
This holder option can be used for a tablet or a book. The essence of manufacturing is the same, only it is necessary to fit the part to the size of your gadget, as shown in the figure.
It is necessary to use well-flexible cardboard so that the stand does not "open".
It is important to understand that a cardboard stand is not necessarily a sloppy brown construction. It can be stylish, comfortable and beautiful. You just need to change the shape a little and the result will change dramatically.
Origami paper phone stand
Perhaps you do not have cardboard at home, but there is thick paper. It is also suitable for making a stand! All you need is paper and scissors. Cut out the shape as shown below, then fold along the fold lines.
That's all. The origami stand is ready to use.
Wire stand for phone or tablet
One of the budget options, made from improvised materials.
During work you will need:
- wire 2-3 mm thick
- pliers
- wire cutters to cut the wire
Everything is done as simply as possible: in the right places, the wire is bent so that a holder is made from it.
To make the design more stable, the wire can be connected with a rubber band.
Such a stand can be a real design solution: it can be painted in a different color and it will completely change, or you can fill in the “voids” with decorative wire curls. This design is suitable for both phone and tablet, the difference is only in the size of your gadget.
Unusual phone stand from Lego
Probably, this version of the stand will especially appeal to teenagers and men. Here you can show your imagination by creating a whole complex for your smartphone with the ability to change position, and maybe even amplify the sound of the speaker, or get by with a minimum of details. The creative process will not only bring pleasure, but also benefit.
To make such a design, you will need a few parts and a base. The tilt level can be changed by adding or removing details. And the position of the gadget is easy to change, just adjusting the design.
Phone stand from an old cassette
Perhaps someone has an old cassette player lying around at home. It is unlikely that it will ever come in handy, and with the advent of disks and electronic media, no one uses cassettes anymore. But still, you can find a use for the cover in which the cassette was located.
To do this, it is enough to "turn" the cassette player inside out by folding the cover back. You can put a phone in the hole where the cassette was held. One of the advantages of this design is that it is easy to wash and it is transparent.
Plastic bottle phone stand
Many of us go on a trip or travel on business by train. Often, on trains, there is nothing near the sockets where a phone could be securely placed. However, the gadget is discharged and needs to be charged. You can simplify this task with a stand made from a bottle. Its essence lies in the fact that the gadget is placed in the cut off bottom of the bottle, which remains hanging on the plug from the charging device. Thus, there is no need to stand nearby and hold the phone in your hands or look for a way to secure it.
To make this holder you will need:
- plastic bottle for shampoo or drink
- scissors
First, wash the bottle to remove any cosmetic or soda residue. Then, mark it up. The back wall of the stand should become a kind of handle on which the phone holder will hang. The front wall should be high enough so that the phone does not fall out over the edge. The next step is to cut the stand around the office.
To do this, it will be more convenient to use a sharp clerical knife.
Cut a hole in the top of the handle so that it can be attached to the charger plug. You can decorate the stand for every taste: with adhesive paper, paints or stickers.
Wooden phone or tablet stand
If you want to make an original stand, then one of the good materials for making it is wood. Such a stand will be strong, durable, and can also serve as a good gift for a loved one. It is important to understand that working with wood requires some minimal skills and special tools.
In the process of work, in addition to a wooden block, you may need materials such as:
- jigsaw
- sandpaper
- wood cutting knives
Be careful and attentive while working with such tools.
Stand manufacturing steps:
- Process the wooden block by sawing off the excess parts and making a recess in the top middle for a phone or tablet.
- Using sandpaper, remove all roughness and splinters from the surface of the future holder.
- You can cover the finished product with varnish or special paint.
Another option for a wooden stand for a phone or tablet can be called an analogue of its cardboard version. In this case, instead of a wooden block, it is better to use plywood.
To do this, make a template for the "legs" of the holder and a crossbar that will fasten them together. And transfer it to plywood. Carefully cut out with a jigsaw and smooth out irregularities and roughness with sandpaper. Using super glue, connect the legs and the crossbar.
DIY stand case for phone or tablet
The most popular option for a gadget stand is a stand case. It will take a little fiddling with it, but the result is worth it. This option is convenient to take with you when traveling, it is durable and can protect the screen.
To make this holder you will need:
- cladding material, it is best to choose leather
- interior cladding material
- simple and thick cardboard or rigid material
- rubber band for fastening
- pencil
- ruler
- scissors
- double sided tape
How to do it?
- Cut the cardboard according to the size of the tablet, so that it completely covers it. This is the future base, the dimensions of which will be the base for all elements.
- Make a few folds in the way that the front of the case will then need to bend to support the tablet.
- Now we take a hard material, which will give the case stability. Cut it so that it follows the contour of the workpiece.
- We apply to the base and make a border, so that it does not interfere with the folds.
- From the inside, we process the cover with soft materials, gluing it to the base blank with double-sided tape.
- The next step is fasteners for the tablet itself. To do this, we make small holes in the hard elements for rubber bands, which will hold the tablet.
- From the outside we glue the finishing material.
Do this as carefully as possible. The appearance of the product will depend on this.
That's all. The stand is ready! It is convenient and can be used not only as a holder, but also to protect the screen.
Pouch for tablet or phone
An original and cute version of the stand for the gadget. It is suitable for girls and can become a cute home accessory.
For manufacturing you will need:
- scissors
- the cloth
- stuffing material
- thick cardboard
- thread and needle
- button
Manufacturing process:
- First you need to cut out a template from cardboard according to the size of your gadget.
- Then cut a rectangle out of the fabric twice the size of the resulting template.
- Fold the base of the fabric in half and mark the crease with stitches 10 cm from the edge.
- Sew the bag, leaving one side unswept.
- After turning the bag inside out, position it so that the seam runs through the middle, and at the end you get a rhombus. After ironing it, bend the upper corner of the rhombus so that it is in the middle and sew. This is shown in more detail in the figure.
- Then insert cardboard into the product and fill the remaining space with stuffing material.
- Make a seam along the very edge of the template. After folding the edges of the unsewn side, carefully stitch it, leaving an opening for stuffing.
- Make a roll and sew up the hole.
That's all. The product is ready. You can decorate it to your taste, giving it even more charm!
Phone holder made of stationery clips
Another interesting and at the same time very simple option. If you have a few stationery clips at home, feel free to use them!
You will need 2 clips: one larger and one smaller. By connecting them together as shown in the figure, in a couple of seconds you will get a holder for the phone.
It can also be done with two clips of the same size.
Stand for phone from an unnecessary CD-disk
An unnecessary CD-ROM can serve as a stand for the phone. In order to make such a holder, you will need a little time and work with temperature. So be careful!
Conclusion
For a creative person, all boundaries are erased. And he can create any object with his own hands from improvised materials. For the stand, you can use options such as an ordinary office business card holder, or a book stand well known to all of us since school days, even a toilet paper sleeve can be an excellent holder option.
There are many opportunities for creativity, you just need to carefully look around. Maybe you will make the most unusual smartphone accessory with your own hands!
In our progressive time it is difficult to meet a person who does not have a mobile phone. Even sending a child to first grade, parents provide him with the necessary means of communication. We use modern mobile devices not only for communication, but also for gaming applications, typing, reading, watching videos and much more. Often, the owner, who wants to have a phone always at hand, wants to arrange it in a convenient way. The stores offer various expensive holders, but from our article you will find out what you can do
Stationery binders
Surely those who study or work in the office will have several stationery clips called binders on their desktop. Next, let's look at how to make a phone stand from these devices. To create a strong holder, you can use 1, 2, 3 or even more binders. Some craftsmen assemble three-dimensional structures from a variety of clips of various sizes. But such coasters look bulky, and they are inconvenient for temporary use. It is enough to fasten two binders together and do not forget to bend one metal end of the holder slightly towards the phone located on it. Even one piece with a folded lug will be enough to support the mobile device.
From the same binders, you can build another structure by placing the clamps opposite each other so that the ears look to the sides. The phone is inserted into these ends, as if into grooves. To keep the clips stable, clamp a small piece of cardboard on both sides.
Using pencils
If there are no binders at hand, the question may arise: how to make a phone stand out of pencils. Before building this design, prepare 4 rubber bands and 6 pencils. In fact, you need to assemble a three-dimensional geometric figure - a tetrahedron. The principle is that it is necessary to fasten two pencils with an elastic band, and stick the third between the turns. It is advised to use pencils with an elastic at the end to prevent slipping on the table and a stronger grip on the phone.
bottle models
In the household, we use a variety of cleaning and detergent products. Most of them are contained in plastic containers. It can be used as a mobile device holder. And how to make a phone stand out of a bottle, we will consider further.
The type of fixture will depend on the shape of the container. It can be a container for shampoo, shower gel, cleanser and more. Take a bottle twice as long as your phone. Cut off the neck and part of the container on one side approximately to the middle. All sizes are relative - measure at your discretion. On the opposite area of the bottle, cut a hole corresponding to the parameters of the charger. You should end up with a piece that looks like a handbag or a pocket with a handle. Put the phone in the stand and connect the adapter to the network through the hole. Your mobile communication device will not lie on the floor, and the risk of crushing it will disappear. You learned another way - how to make a phone stand. If desired, this holder can be painted, pasted over with beautiful paper or cloth.
paper clips
The simplest and most affordable stand option is an ordinary metal paper clip. It must be unfolded into a straight line and folded as shown in the diagram. The resulting product is quite strong and stable. This design perfectly holds the mobile phone without interfering with watching the video at all.
Cardboard and plastic cards
How to make a cardboard phone stand? You will need a cardboard sheet from which you will need to cut a strip measuring 10 x 20 cm. Then you need to fold it in half along the short sections. Next, draw a shape as shown in the photo below. The fold line must remain intact. Opening the detail, you will see that you have a comfortable and stable phone stand.
If you have an unnecessary card lying around (any discount card), it will also make an excellent phone stand. To make such a device at home is very simple. Step back from the edge of the card 1 cm and bend the part along the short side. Bend the rest of the card in half in the opposite direction. You will get a zigzag shape. Place the phone on the formed ledge. The stand is ready.
Unusual coasters from simple things
Savvy people began to use ordinary glasses as a phone holder. They only need to be turned upside down, which, in turn, must be crossed. The mobile device is located between the bezel and the temples that hold the phone.
How to make a phone stand from a children's designer? In this case, it all depends on your creativity and imagination. To create such a model, you need to use a platform and several bricks of various shapes. The stand made of parts can hold the phone both vertically and horizontally. The tilt of the screen can be adjusted by adding or removing additional bricks.
Another interesting detail that will help keep the phone upright is the old cassette holder. It must be opened and the lid folded back, thereby turning the box inside out. In the hole that once served as a pocket for an audio cassette, you can put your communication device. The convenience of the stand is that it is quite durable and transparent, does not interfere with the use of the phone. In addition, it can be easily washed.
As you can see, from the simplest items that can be found in every home, you can make such a useful thing as a phone stand.
Homemade mahogany smartphone stand.
Hi all! Today we will make for a mobile phone in the form of a dog - a symbol of the year.
Now you need to make a stand for it. To do this, we cut out a circle with a diameter of 70 mm from wood. Sand it down with sandpaper.
We take a few gears that are so small.
We also take epoxy and hardener.
We take plasticine and apply a thin layer on one of the sides of the internal cavity of the figurine and glue it with polyethylene on the same side.
We knead the epoxy glue according to the instructions and pour about 2 mm into the cavity of the figure. This will be the first layer. We are waiting for the solidification of this layer. Then lay out our pattern of gears and fill in the rest.
Our dog is dry.
We remove plasticine. We take sandpaper and bring everything into a divine form.
We mark with a pencil on the figure the point where the hole will be.
Drill make a small indentation.
Now we make a wooden chop that will fix it all. We insert the chopstick into the stand, spread it with PVA glue and also the lower part of the figure with a thin layer so that the glue does not protrude. We connect. Leave until completely dry. Next, we rub our entire product with herbalist impregnation.
Here's what we got.
