Corner shelf made of chipboard. Do-it-yourself shelves on the wall: we make a shelf on the wall with step-by-step instructions. Wooden shelves on the wall

In order to rationally use the space in small rooms, there is one pretty good option - a wall-mounted corner shelf. The possibilities of its application are very wide. For example, such shelves are often used for icons, books, various awards, and so on. Don't forget about the kitchen. Here such a shelf can be installed under a small TV. In addition, in the bathroom or bath, it allows you to store bath accessories. This option is advantageous in the first place by the opportunity to save space. Corner shelves for shoes are also quite popular.

As you can see, the use of such furniture can be found in any room. The easiest way, of course, is to buy a corner shelf in a store, especially since there will be no problems with the choice. However, there is an alternative option - to make it yourself, from plywood, fiberboard, or even from improvised materials. Such work does not require any special knowledge and skills. The main thing is just to want and, of course, to clearly understand what exactly you need.

Corner shelf - how to make it yourself

So, let's take a closer look at what are the possible options here. First of all, we need to decide on the material. Corner shelves can be made from:

• plywood;
• drywall;
• window sill profiles;
• glass.

In the latter case, trimming of the material is best done in the workshop. After all, it is very difficult to do it yourself without the lack of appropriate skills. You will also need to purchase special holders. It is preliminary recommended to draw a drawing of the shelf, according to which you will then begin to carry out the installation. The assembly itself will not cause much trouble, because the material is already cut. Holders are attached to the wall with self-tapping screws. Don't forget that the shelf needs to be level, so you'll need a level.

Quite often, plywood, MDF or chipboard is used to make a corner shelf at home. You can fix them in different ways - landing on a longitudinal or fixed in the grooves of the transverse base. The first option is simpler, since there is no need to drill walls.

First of all, we draw a drawing with exact dimensions. Next, we need to cut the shelf itself from the selected material. To do this, draw a circle on its surface and divide it into 4 equal parts. Here you will need a compass, a ruler and a simple
pencil. Next, cut out each of these 4 parts with a hacksaw or jigsaw.

After that, you need to take the base rail and mark it. In particular, you must specify the size of the groove, as well as the location of the shelves. The most optimal cutting depth is approximately to the middle of the rail, no more. Next, we outline the area that we will cut out on the shelf itself - this is done at the base corner. It should be noted that its area should correspond to the width and depth of the groove we made earlier in the rail. Sawing both in the first and in the second case, it is better to do it with a saw with fine teeth. We check how the shelf fits into the grooves of the base, and if necessary, eliminate the flaws.

Next, we need to fix the rail on the wall. This is done with glue. After that, it is better to secure the rail with tape and wait about an hour. We need the glue to hold securely. During this time, you can do the grinding of the shelf itself. Here we need to make a small digression. If you are using untreated wood, then immediately before installation, all parts of the shelf must be coated with paint or varnish and wait until they dry. After that, you can already start installation. In this design, the shelf is simply inserted into the rail. No additional fixing is needed here.

If you chose the option with a transverse base, then the sequence of actions when assembling the shelf will be somewhat different. In particular, first of all it will be necessary to make grooves, and only after that you should start working on the main element. So, we take 2 bars, the length of which corresponds to the size of the sides of the future shelf. They need to cut grooves of the width we need. The easiest way to do this is with a circular saw.

Next, we need to fix these elements on the wall using self-tapping screws. After that, we measure the angle and transfer the obtained values ​​directly to the material. On its surface, we need to accurately draw the outline of the future shelf and cut out each element. The edges are decorated with a special tape. In fact, we have already reached the finish line. It remains only to insert the finished shelf into the grooves.

A fairly popular material for the manufacture of corner shelves is a PVC window sill profile. You should immediately warn that in this case it is necessary that the angle be really right, that is, exactly 90 degrees. The thing is that it is quite difficult to adjust this material to uneven walls. If the angle is straight, then you will not have any problems with the manufacture of the corner shelf from the window sill profile.

We mark the prepared material and cut it out along the drawn contours. In this case, it is best to use a hacksaw. Next, we strengthen the rigidity of the edge of the workpiece by gluing a wooden lath matched to the size with pre-drilled holes for self-tapping screws. Here you can use any adhesive suitable for connecting these two materials. By the way, you can fix the shelf on the wall both with the help of self-tapping screws and on coal mounts. Which option to choose - decide for yourself.

We still have one more unsolved problem. After all, one end of the corner shelf remains open and spoils the whole appearance. The problem is solved simply - with the help of a cable channel of the appropriate thickness, mounted on glue. It should also be noted that our shelf will be white. Of course, this is a kind of universal option. However, many people want some other color schemes. This is where a special self-adhesive film will help us. There are any colors on sale, so you can easily fit the shelf into the interior of the room.

The corners in the room almost always remain unoccupied, but meanwhile there is enough space there to accommodate a small shelf, rack or suspension. From a design point of view, the corner arrangement offers some advantage, because such a wall articulation expands the possibilities of using various configurations of structures and the fasteners used. If you compare ordinary and corner shelves, you can immediately notice how much more diverse and attractive the latter look. Let's try to decorate your house with such a corner shelf.

The most popular materials for making shelves are wood, furniture board, MDF, laminated chipboard, etc. Sometimes shelves are made from improvised means - laminate, plastic or even drywall. We will not change traditions and take furniture plates as raw materials. To work, you will need a jigsaw, a drill, various fasteners, a tape measure and a pencil. First you need to make a sketch of the future shelf for clarity of work processes.

The shelf will be about 70 cm high with three sections. It will be fastened through the vertical elements with the help of dowel-nails, and the parts will be connected to each other by confirmations.

The first thing to do is mark all the details on the plate. Usually this is done with a pencil, but if the plate has a dark surface, then the pencil mark will not be noticeable, in which case you can use a knife. It is necessary with his blade, without pressing hard, to draw along the line of the cut, after which a thin, white, noticeable line will appear, along which it will be easy to cut.

To cut out the elements of the shelf, you can use an electric jigsaw. The saw blade should be fine-toothed and designed for woodworking. The sawing speed regulator on the jigsaw must be set to the minimum value, and the mode selection knob must be set to "0". To facilitate the assembly of the shelf, it is necessary to number the parts on the drawing, and then put down the corresponding values ​​on the structural elements themselves.

After all the details are cut out, you need to drill holes in them for connecting with confirmations. It's much easier to do it consistently. First you need to make holes in the shelf, and then drill through these holes corresponding to them in the supporting element. If there is no special drill for confirmations, then it is necessary to use 3 ordinary drills with different diameters - for the screw part, thickening and head of the euro screw.

Immediately at this stage, you can make holes for attaching the shelf to the wall. It will be fastened with dowel-nails 6x80 mm through the supporting elements. All holes must be countersunk to ensure that the nail head is flush with the surface.

When all the details are cut out, you can start decorating the edges. First, we clean all the edges of dust and sawdust formed during sawing. Then we apply an edge tape to the ends and, using a heated iron (it is advisable to take an old, unused one), glue it to open surfaces.
This trimming tape is produced in a standard width of 1.8 mm, and the thickness of the furniture plate is only 1.5 cm, so part of the tape remains redundant and must be removed. We cut off the excess part of the edge with a regular wallpaper knife.

We clean the resulting edge with fine-grained sandpaper. You can close the ends by any other available method, for example, use a decorative cord, braid, special paper or cardboard.
Now you need to assemble the shelf. The assembly is carried out in accordance with the numbered scheme. We use a hex wrench to tighten the confirmations.
We try on the assembled structure in the place intended for it and mark the attachment points on the wall. For drilling in concrete or stone walls, we use a drill with a pobedite tip. On the drill tip, you can pre-mark the drilling depth required for the prepared dowel. So that the dust generated during drilling does not scatter, you can stick a paper "pocket" on the wall under the place of work.

After drilling is completed, you need to insert the dowels into the holes and, through the corresponding elements of the shelf, fix it with screw nails, drowning the hats. This can be done with a hammer or a regular Phillips screwdriver.

You can decorate the open caps of the fasteners with the help of special plastic plugs of a suitable color.
Perhaps such a shelf will turn out to be too simple in appearance, but we made it from materials that often gather dust in our pantry or live out their lives in the country. The design can be changed at your discretion, for example, to make the supporting elements longer and then the shelves can be used as bookshelves. Or choose a different shape of the end pieces, in which case the shelf will acquire additional decorative effect. In any case, a hand-made item will serve as an example of the individual skill of the owners of the house.

We examined what corner shelves are (in a stand-alone version).

Today we will look at how quickly and easily you can make a module of such parts.

Well, I don’t think it’s worth talking about how these shelves are made. Their production is ordered together with cutting.

They are cut out, processed with a cutter, and “rolled up” with plastic, 2 mm thick on special equipment. In a word, corner shelves are best done not in artisanal conditions.

And since we are talking about how to make furniture in artisanal conditions, let's take a better look at assembling a module with corner shelves.

So, the module itself consists of a side, a back part and three corner shelves.

First, “by eye” we make three holes in the end of the rear wall (just make sure that the middle one is not in the center, since there will be an axis for mounting the corner shelf).

Then, we apply it to the side of the module (in the place where it should have holes for connecting to it, align their extreme ends, and make notches on the side part with a pencil, opposite the holes made in the laid part).

Stepping back 8 millimeters (we have chipboard - 16 millimeters thick), we make holes in the side part.

As you can see, we do all the markup without a tape measure, “live”. Moreover, in this case, we get a fairly good accuracy (coaxiality of the holes).

After that, we connect it to the back wall.

But here you need to be careful.

If you make two perpendicular holes close to each other (near the corner of the shelf), then when attaching the shelf (when confirmations are screwed into it), these confirmations may intersect. Therefore, by applying a confirmation opposite the hole made, we determine (visually) the position of the perpendicular hole.

After that, again, we apply the shelves to each of the joining faces (side and back wall), and mark the position of the holes.

When the holes in the side part and in the back wall are made, we fix the shelf. When fixing the shelf, you need to push it towards the mating surface in order to remove possible gaps between them.

The problem of free space is always relevant, especially for small apartments. What if you want to place your favorite books or children's crafts? Help out the corner shelves.

Almost always in the apartment there is an unoccupied free corner in which a rack or a small shelf will be perfectly located. This will free up some space and also add a new decorative element.

Materials for the manufacture of shelves

Today it is difficult to find a house or apartment in which there are no shelves. They are convenient to lay out personal hygiene items in the bathroom, arrange books, flowers, kitchen utensils or small crafts and knick-knacks. The angular position provides great opportunities for design imagination when creating various configurations of shelves.

Corner shelves due to the design are able to save the space of the apartment and at the same time aesthetically decorate the corners.

Today it is possible to choose a corner shelf on the wall for any room. Specialized stores are ready to offer a wide range of shapes and designs from various materials. But the cost of such shelves is not always suitable for each of the potential buyers.

Traditionally and classically, the wall made of wood simply looks. It can be done in a minimalist style, but still remain attractive.

Open corner shelves help to make the living and working space more functional, and can serve as a spectacular detail of the overall interior solution. To the question of how to make corner shelves, do-it-yourself corner racks are suitable based on the available free space and the planned design.

Do-it-yourself options for corner shelves and open shelving

The appearance of furniture is largely determined by the materials used in the manufacture. An open corner rack can be made from solid wood and chipboard, MDF and plywood, glass and metal. And in each version, the same constructive solution will look different.

An open corner rack can radically change the appearance when changing minor details.

Also, combinations of different contrasting colors can change the usual model beyond recognition.

How to make an open corner rack step by step

First of all, it is necessary to determine the overall dimensions of the open rack. As a rule, all models have an extremely concise design and easily fit into the allotted space, supporting the overall interior solution.
Open shelves can be mounted both on the rack frame and directly on the wall. In the second case, in order to fix the corner shelves neatly and beautifully on the wall with your own hands, you will need to purchase special holders for shelves - toucans (pelicans) or consoles of various configurations.

Also, a corner rack with shelves can be floor and wall. In the first case, it is necessary to provide a basement box in the design. Usually I do not make solid sidewalls to the floor - so that the plinth does not interfere with moving the product close to the wall. After all, it is not always possible to cut it off; wiring is often “hidden” inside the hollow plinth.

Consider an example of calculating the detailing and drawing up maps of the cut of a corner rack with your own hands using the example of the first model.

Step 1. We draw the design on a scale, indicating the overall dimensions and numbering of parts. Thinking about how the parts will be connected to each other. Since the rack will stand close to the walls, it makes no sense to use hidden fasteners in the form of dowels and eccentric ties. If the through holes on the bottom shelf, in the places where the basement box is attached, are also “embarrassing”, discard the euro screws (confirmations) in favor of the corners.

Step 2 We paint the corner rack with our own hands in the form of detailing, draw up cut cards. The calculation is given for chipboard 16 mm thick. For materials of other thicknesses, the dimensions of the shelves will be slightly different.

Step 3 After cutting out the details, designing the radii, we roll up the visible parts with a melamine or PVC edge.

Step 4 According to the fastener marking specifications, we drill the parts for further assembly.

If you did everything right, the corner shelf will assemble with your own hands as a “constructor”, like a regular serial product.