How to assemble an old vacuum cleaner. What can be done from the motor from the vacuum cleaner. but on the other hand

The vacuum cleaner is “dead”, but the motor is still in working condition - a common situation “Maybe it will come in handy” - the practical owner thinks, considering the remaining electric motor. Well, it’s not customary for us to throw away something that still works! It will turn out, as with the hero of an old joke - it's okay, but suddenly it will still come in handy. Moreover, both modern appliances and old Soviet vacuum cleaners fall under the scope. Therefore, the forums are full of "crazy" ideas for what to attach the motor to.

10 ideas to put the engine to good use

Men are restless creatures, and Ukrainians are also enterprising. Not a single bolt will be lost, not like the motor from a vacuum cleaner! It's a shame to throw it away. That's why people ask the question: what to do with the remaining engine.

10 masterpieces that impressed the worldly-wise ALM-remont experts:

Connect the motor to the hose and inflate the stove in the bath.
Put a bag of dense polyethylene on the back of the unit, connect the hose, wrap it with tape and use it as a spray gun.
Put in the ventilation shaft and smoke in the apartment.
Connect to an emery wheel and sharpen knives.
Pump up the rubber boat.
Adapt to lawn mower.
Use as a mixer.
Make a water pump.
Attach the blades, put on a motor boat.
And the last "pearl": to make cotton candy.

As you can see, the people are infinitely talented in a creative impulse. That's just how safe such ideas are - we'll figure it out further.

but on the other hand

Professional "techies" from the ALM-remont service company warn: most of the options listed above are a reason to check if you have a Guardian Angel.

For example, a motor at 16 thousand revolutions will tear an emery stone circle to shreds, and the fragments will scatter to the sides at breakneck speed, like a grenade. Similarly, with a lawn mower - not only grass will fly to the sides. To make the engine work, you need an additional “upgrade”: belt drive, pulley, precision nozzles, clutch and balance. Even with a higher engineering education, it is difficult to guarantee that the new unit will work as it should.

Give your vacuum cleaner a second chance

Rather than risk your health, it is better to fix a broken vacuum cleaner. Masters know: in 95% of cases, the device can be “brought back to life”. Vacuum cleaner repair will not hit your pocket, because the most expensive part - the motor - works.

What problems are being fixed:

faulty power circuits;
torn hose;
damaged cord;
worn bearings;
clogged filter;
damaged graphite brushes.

These and other malfunctions of the master eliminate and change broken parts for new ones. If the vacuum cleaner is junk, this is not a reason to send the device to the scrap. Go to http://alm-remont.com/remont-pylesosov and find out how professionals solve problems.

Let the vacuum cleaner motor work as intended!

What useful things can be done from a vacuum cleaner motor

When buying a new vacuum cleaner, the old unit is most often thrown away. But if an older vacuum cleaner is still working and quite serviceable, it can get a second life. Some methods require technical education, since it is dangerous to redo equipment, and especially motors and unknowing people are better off not risking their health and entrusting such work to professionals. The safest and easiest ways to make a motor from a vacuum cleaner or itself will be presented in this article.

Grain crusher
The car
Attraction
Air blower

Grain crusher

To make a grain crusher from a motor from a vacuum cleaner, you need to have some skills. People who do not understand the data structure and similar devices should not independently convert the motor into a grain crusher.

First you need to take the base from a square sheet of plywood and fix the electric motor so that the shaft drops down by forty millimeters. The steel plate must be installed on the threaded tail, and the plate is fixed with nuts, bushings and washers. On both sides of the axis, the leading edges must be sharpened, and the axial hole itself must be made exactly in the middle of the plate.

To make a working chamber for a future grain crusher, you need to make an annular body of metal strips. For everything to be correct, you need to bend the edges of the ring outward so that they form flanges of ten millimeters. It is with the help of these flanges that you can attach the body to the base and fix the sieve to them.

The car

Since car owners treat their vehicles very carefully and reverently, cleaning should be of high quality and fast. No matter how much money you spend on another vacuum cleaner for your car, you can simply use an old home vacuum cleaner. If the motor of the vacuum cleaner is fully operational, it can easily cope with dust, crumbs and dirt in the car. It can be used to clean seats and carpets.

Since men love to spend their time in the garage fixing the car or something else, the place is often dusty and dirty. In the garage, a vacuum cleaner is useful for cleaning sawdust, dust, sand and other things. An old vacuum cleaner with a working motor will become an indispensable assistant for cleaning both the garage and the car.

Attraction

If the motor in the old vacuum cleaner is still quite working, you can use it as an attraction for children. To do this, you need to pierce the tennis ball with a pin so that the pin is on both sides. After that, you need to make a propeller from a polystyrene jar, which will be fixed on top of the ball. For the propeller, one strip cut with ordinary stationery scissors will be enough.

The propeller needs to be pierced in the middle and put pins on the axis. In order for it to rotate easier and faster, you need to make bearings from beads that need to be attached to both sides of the propeller strip. Also, you need to bend the top edge of the pin in such a way that it does not have too much play on the axis. Such a "flying ball" can be launched into the air using the air blowing function. Over time, you can learn to give maneuverability to the ball with the help of air flow. If desired, the ball can be decorated with sparkles or decorated with any color.

Air blower

If the motor is still running in the old vacuum cleaner, then it is quite fit for work. In addition to its direct duties, the vacuum cleaner can be used as an air blower. It is perfect for inflating children's pools, balls and mattresses.

In addition, an old vacuum cleaner with a working motor can be taken to the country house and used there. It is perfect for cleaning leaves with the help of reverse air supply, that is, by simply blowing them in the direction of your choice.

Household appliances break down and wear out over time. A vacuum cleaner is a classic household cleaning tool. Often, when this unit breaks down or wears out, people buy a new one without thinking about what can be done from the heart of the dust collector - the engine.

Today there are many different models of vacuum cleaner. However, all devices are made according to the same principle. The engine of the unit during operation is gaining power, which rotates the impeller.

Disassembly

An engine for building the necessary household appliances. But before creating a new item, you need to get and disassemble the heart of the dust collector.

Sometimes during disassembly, it becomes difficult to remove the nut that holds all the parts of the unit together. The nut holder sits firmly in the middle of the motor with sealant.

Samsung dust collector motor - 11ME83

Attention! It is impossible to scroll the rotor of electric motors with metal devices like a screwdriver, trying to remove the nut. The nut will come off and the winding will be damaged. It is unlikely that it will be possible to restore the stroke with your own hands.

List of required materials

For disassembly you will need:

pliers;
screwdrivers;
wrench for unscrewing the nut with a diameter of 1.2 cm;
vise;
2 wooden bars 10x40 mm;
round file;
a hacksaw designed for metal surfaces.

The dust collector motor is always assembled in the same way. The difference lies in the volume and mass of parts. Tools must match their size.

Procedure

Preparation of the tool and the unit itself is required. First, the brush is unscrewed from the back surface, then the casing is removed, the role of which in the engine is to cover the impeller from the front side.

Broken motor impeller

Often the casing is firmly attached to the body. In this case, pliers are used: the edges are bent on the sides and the casing is wrung out with a screwdriver.

The procedure for unscrewing the nut:

The rotor is carefully locked by tightly clamping it through the recesses that are designed for the brushes. This will require bars, the size of which is indicated above. Wooden blocks are inserted into the recesses for the brushes. The whole structure is tightly pressed against the anchor with a vice. If the bars do not fit into the brush holes, they can be filed with a round file.
The nut is unscrewed using a wrench. The wrench nozzle is selected according to the size of the nut.
Removal of the rest of the structure. Suitable screwdrivers are taken from the tool kit to unscrew the remaining parts on the engine.

They disassemble the motor in order to determine a breakdown or upgrade to create other useful household items.

Creation

What can be useful to do from the engine of the vacuum cleaner? The following are products that are designed using a dust collector motor.

lawn mower

For people who are thinking about where to introduce the engine from a vacuum cleaner, it is proposed to design their own lawn mower.

This household item is constructed using the heart of a vacuum cleaner in working condition. Usually dust collectors wear out and are thrown into the trash. Instead, the engine of the unit can be used to build a lawn mower: sufficient power is 500 watts.

Homemade lawn mower made using a vacuum cleaner engine

Materials required for assembly:

apparatus for welding;
Sheet steel;
unnecessary baby stroller;
old saw or hacksaw.

To begin with, the wheels of the stroller are separated. It is better if the wheels are large, as this will ensure the patency of the product on uneven and rough soil. Excess parts are cut off, but you can leave the handles, as it will be convenient to hold the lawn mower while moving.

Next, a platform is constructed, on which the engine with the dust collector shaft is then placed. It is necessary to follow the rules under which the platform with the shaft will be facing the bottom. To protect such a motor and shaft from possible damage, you need to cut a casing about 1.2 cm thick. A hole is cut into the casing. The size of the hole should be 0.5 cm larger than the motor placed on the platform. Before installation, the distance from the motor to the floor is measured. The size of the distance is not less than 3 cm.

The next step is cutting the steel disc. Diameter - 35-45 cm. The volume of the disc is compared with the force applied to unwind. A disc 45 cm or larger requires a powerful motor. When building a lawn mower, it is better to use a larger disc, as the power of this vacuum cleaner engine never fails. A hole is drilled in the central part of the cut disk. The tip of the shaft passes through it along with the engine.

2 cm are measured from the sides of the disk, then 2 holes for the knives are drilled at the indicated distance.

The old saw is deformed and turned into 2 knives. Before inserting into the above holes, the knives are sharpened. Recommended length - 5.5 cm, width - 3 cm. Using M6 bolts, the cut parts are fixed on the disk. Blades every 3 lawn mowing.

Read the article - using a vacuum cleaner.

Trimmer

A trimmer is a device that performs the functions of a lawn mower for hard-to-reach places.

Grass trimmer

To assemble a garden tool you will need:

extrusion;
dust collector motor;
homemade knives;
disk made of plastic or steel.

The engine is fixed at the foot of the bar. Knives cut from a hacksaw of the same size as in the above section are attached to the shaft. Another option is to attach a disc to the shaft and make a hole in it for threading the fishing line. From above, for protection, the device is covered and secured with a casing.

Alternatively, you can use a plastic casing. It can be built from a sewer pipe, which is usually used when installing a mixer.

To cool a high-power engine, the following device is made: a disc with concave blades is inserted under the place where the fishing line is threaded. This part serves as a fan.

Fan

From the motor of the old dust collector comes out an excellent fan for cleaning rooms. What you need for construction:

compacted rubber bands;
turbine motor;
half of the body from the vacuum cleaner.

Wires are brought out to the body and the motor is fixed. Then rubber bands and a casing are put on to protect against damage. Air is drawn in from one end and exited from the other.

Finished blower design

A plastic cone is attached to the place where the air mass exits, the end of which is cut off.

Next, a plastic tube is attached to the body, which will serve as a handle for holding. You need to bend the tube carefully so as not to break it, so it is better to heat the bend points for several minutes with a hairdryer.

Turbine vacuum cleaners have a lot of power, so there is strong air ventilation. Apply built fan. The main advantage is that there are no costs.

What useful things can be done from a vacuum cleaner motor

Grain crusher
The car
Attraction
Air blower

To make a grain crusher from a motor from a vacuum cleaner, you need to have some skills.

What can be done from a vacuum cleaner engine?

People who do not understand the data structure and similar devices should not independently convert the motor into a grain crusher.

The car

Attraction

Also, you need to bend the top edge of the pin in such a way that it does not have too much play on the axis. Such a "flying ball" can be launched into the air using the air blowing function. Over time, you can learn to give maneuverability to the ball with the help of air flow. If desired, the ball can be decorated with sparkles or decorated with any color.

Air blower

http://whatican.ru

█ Vacuum cleaner how to unscrew the nut. Vacuum cleaner engine repair (how to disassemble the engine) fixtures.

In this video I will tell you how easy it is to unscrew the nut on the vacuum cleaner motor without any planks and other special tools. The cost of a subscription to our club is 300 rubles. The essence of the project is to create a group for training in the repair of the main types of electronic and digital equipment with the further opening of their OWN business. At the same time, the construction of the course will affect not only beginner craftsmen, but also represent the interests of the ALL audience: from the layman (who does not know how to hold a soldering iron) to experienced craftsmen who already want to go higher and become a LEADER, start their OWN business! We have assembled a worthy team to be able to give IN-DEPTH knowledge on the repair of: Portable digital equipment and mobile devices Laptops, computers, office equipment Household and audio appliances LCD TVs, monitors. The construction of the material is simple and as detailed as possible: from A to Z. WITH REAL everyday malfunctions, typical problems and sometimes NON-STANDARD solutions! The project is constantly

How to unscrew the nut on the vacuum cleaner motor. super way! motor repair. The easiest way to disassemble the Samsung vacuum cleaner motor. ;). My fourth homemade grinder. My channel shows how it works. The engine used from the "washer" 2800 rpm. min, 120 watts. power. We calculate the belt speed according to the formulas: Roller circumference L=2PR=DP(R-radius, D-diameter, P-3, 14) Engine revolutions per second. F=2800 60=46, 66 Belt speed S=L*F. Upper roller: width 50mm, diameter 50mm in the center, to the edges it decreases to 48mm (barrel-shaped for adjusting the tape) from the ends of the groove for bearings. Bearings 180201 (international designation 6201 2RS) dimensions: inner diameter 12mm, outer diameter 32mm, width 10mm.

Homemade grinder No. 4 "mini grinder" How to replace the risers in the apartment, a list of materials, and the price of the issue. REPLACEMENT OF THE SEWER STICK OF COLD AND HOT WATER. ___________________________________________________________ LINK to our CHANNEL: — — — Repair of the APARTMENT P. 1 Exclusive 2017 All Step by step — DISMANTLING WORKS P. 2 MAIN DUSTY STAGES Repair of the apartment. Replacement of the cold water riser. Replacing the hot water riser. Sewer line replacement. Sewerage. Replacing Clay Main Sewer Line With ABS Plastic Pipe. Basics of Your Home's Plumbing. Stages of replacing the riser in the apartment. Replacement of cast iron sewer. Replacing the cast iron riser in the apartment. Replacement of the common riser. Cast-iron sewage. water in the house. water pipes.

█ replacement of the sewer riser h.-3 / cold and hot water / sewerage. Repair of the starter anchor: Polishing the lamellas (ALPHA, DELTA, SABUR 139FMB) Foam filter ● LED stop signal - If you like the video, you can support the channel by donating any amount you wish. MasterCard — 5168 7553 2759 3097(PrivatBank) QIWI — +380937373045 Yandex — 410012753834964 Webmoney — Z393128700795 EasyPay — 27467405 ●My Blog – ●My affiliate program! - Connect AIR ●VK group - ●Music - from the free YouTube library ●My wast: Gilera DNA 50 ●I shoot on - Panasonic HC-V110 Black Action camera SJ4000.

Brush Killer Video Sponsor Auto Parts MILES: Auto Repair Channel: Dimexide to Engine Step Drill AutoScanner My 2nd channel. Before unscrewing, ALWAYS check which thread (in which direction to unscrew) My affiliate program on You Tube.

1 how to disassemble the engine from a vacuum cleaner \ how to unscrew the nut \ how to change the vacuum cleaner bearings How to align the corners in an apartment without beacon plaster. Ennoble the holes of the exhaust shaft and what to do with the protruding metal on the walls. Thank you all for your support of the channel. ______________________________________ Link to the CHANNEL: Plastering corners, how to putty corners, how to make an even corner, a corner under a building rule, align corners using a rule, how to remove rust from walls.

█ how to align the corners of the walls in the apartment / shaft hole / rust on the walls. The pump began to work loudly and get very hot, the reason is the wear of the bearings. With further operation, the motor will jam and the winding will burn out.

When the engine is warm \when it's time to chaMy instagram: The Jet Plane Project is finished! The video on the channel will now be released without a clear schedule. The video was created for those who have not seen the full process of building a turbojet engine and an aircraft for it, but want to see it!

From building a turbojet engine to flying - just one step, you need to say that they are not repairable, but more difficult, but quite maintainable. if not glued with superglue when assembling, then it can be repaired many times.

Remove the impeller of the Zelmer vacuum cleaner How to make emery reverse the engine from the washing machine. How to connect the motor reverse circuit. How to reverse a reversible motor. Motor reverse circuit. How to connect the motor to the plow. Simple reliable electrical circuit. READ TO THE END. How to make emery with your own hands at home yourself. Rotation in opposite directions. Easy fast simple.

A very useful invention from a vacuum cleaner engine

How to connect the engine to 220V. 380 to 220 volts. Pencil sharpener. Sharpening device. Adapt. Homemade. Master Class. Hobby. Leisure. Home workshop. A WARNING! THIS VIDEO SHOWS THE SCHEME OF STARTING THE REVERSE ON THE STARTING WINDING IN THE SHORT-TERM MODE. THE AUTHOR IS NOT RESPONSIBLE FOR YOUR INCORRECT ACTIONS AND ACTIONS. Subscribe to my channel.

How to connect a reverse motor from a washing machine to 220 easilySometimes this problem can be fixed in this way;) Vacuum cleaner Samsung SC4535. We disassemble the turbine. Hello friends! I found a solution to the problem that many craftsmen face and resort to using a hammer and chisel or screwdrivers. After going through a lot of tests and different options for pullers, I found a chic way, both in simplicity and in uniqueness. WE REMOVE THE BEARING WITH THE BEARING! just think about it;) If someone wants to buy such a puller, you can order me, I will do it for you. Further tests will be carried out on the crankshafts of the Chinese. Made in SashaDalkevich MY INSTAGRAM - FACEBOOK - Greetings friends on my motorcycle repair channel! My name is Alexander and at the age of 10, having collected the necessary amount of money, without any demand from my parents, I went to the market and bought a Karpaty moped, from that time my motorcycle career began. It's not a hobby or a job, it's part of my life. I take a very responsible approach to the repair of motor vehicles and, most importantly, I love quality in everything. What I can convey to you dear viewers and subscribers.

With your own hands: how to remove bearings from the crankshaft without a hammer and chisel

Categories

Popular