Vetonite is moisture resistant. Putty vetonit vh technical characteristics. Ordering a quality mixture of Vetonit VH

Peculiarities:

• Moisture resistant.
• High strength.

Suitable grounds:

Specifications:

Foundation preparation:

Preparing the mixture:

Application:

Drying time:

Veronit VH is a waterproof, white, cement-based finishing putty for leveling indoor walls and ceilings, as well as for facades.

Application area
For interior and exterior use. Alignment of walls and ceilings in dry, damp and wet areas before wallpapering and painting. Alignment of walls with ceramic tiles. For fine leveling of plastered surfaces of facades before painting. Suitable substrates: concrete, lightweight concrete, expanded clay concrete, brick, plastered surfaces.

Advantages
For interior and exterior use,
white, smooth surface,
manual and mechanized application.

INSTRUCTIONS FOR USE Veronit VH

The material is waterproof.
The mixture is not suitable for leveling floors and for application on materials with a polymeric, organic and gypsum binder, as well as on weak lime plasters.

Foundation preparation
The substrate must be solid, clean, free of dust and dirt. Substances that weaken adhesion such as grease, dust, etc. must be removed. If necessary, dry and absorbent surfaces are moistened. Windows and other untreated surfaces must be carefully protected.

Mixing
Pour 8-9 liters of clean water into a container and pour 25 kg (bag) of the weber.vetonit VH mixture, while the mixture must be added to the water, and not vice versa. The recommended water temperature is 20°C. Mixing is carried out with a powerful drill with a nozzle for 3-5 minutes. For better dissolution of the binder, the mixture is allowed to stand for 10 minutes. After slight re-mixing, the mixture is ready for use. Mortar mix is ​​suitable for use within 3 hours from the moment of mixing with water. The temperature of the mortar mixture should be between +10 and +30°C.

Execution of work
The mortar mixture is applied by mechanized spraying or manually and leveled with a steel spatula. For full leveling, a two-handed steel spatula 80 cm wide is used, and for partial leveling, a small one, 30 cm wide.
When leveling in several layers, it is necessary to apply each subsequent layer on the completely dried previous one (after 1-2 days). The dried putty surface must be treated with sanding paper and dedusted before applying the next layer.
When leveling facade surfaces, it is recommended to apply the mortar mixture in 2 layers. The first layer is partial alignment and filling of pores. The second layer is a complete leveling of the surface.
In dry conditions, to ensure the necessary conditions for hardening, the leveled surface is moistened with water using a sprayer. After processing with sandpaper, the leveled and dried surface can be painted with alkali-resistant (cement-resistant) paint, wallpapered or tiled, after removing dust from the surface after sanding. To increase the wear resistance of the material and improve adhesion, 10% mixing water can be replaced by Vetonit MD16.

Drying time
The drying time of one layer of the recommended thickness is 1-2 days with good ventilation. Drying time depends on layer thickness, ventilation and temperature. The level of 50% of the final strength is reached within 7 days at 20 °C, with a decrease in temperature, the process of gaining strength slows down.

Tool cleaning
Working tools and equipment are washed with water immediately after completion of work.

Precautionary measures
When working, rubber gloves must be used; avoid contact with skin and eyes; in case of contact with eyes, rinse with plenty of water; keep away from children.

Disposal instructions
Dry mix and hardened material must be disposed of as construction waste. The material must not be released into the sewer. Dispose of the paper bag as normal trash.

Package
Paper three-layer bag with a middle layer of polyethylene - 25 kg and 5 kg. Bags should be stored on pallets, avoiding contact with the ground and protected from moisture.

Storage
12 months from the date of manufacture, if stored in the original packaging in a dry place.

Finishing putty Vetonit is used for leveling walls and ceilings on plasterboard or mineral materials. Use the product for finishing plastered surfaces and plasterboard partitions. With the help of a ready-made pasty mixture, you can get a perfectly flat surface for subsequent painting or wallpapering. Vetonit offers a wide range of products, each with its own purpose. The choice of composition depends entirely on the nature of the work.

Finishing characteristics

Finishing putty Vetonit is a well-known material in the construction industry, which includes several series in the assortment, different in composition and purpose. But all the variations are united by the final result - smooth surfaces of the walls and ceiling. As a rule, Vetonit putty is used with a primer. This ensures increased adhesion of the finish to the base.

The composition of the main component is limestone, there are also gluing components in the form of polymer glue. Thanks to this composition, it will be easy for the builder to apply the finishing Vetonit. The main features of the brand are high quality, which is confirmed by a certificate of conformity.

Depending on the version, wall and ceiling putty has the following technical characteristics:

• thickness of one layer - 1-10 mm;
• the presence of fractions with a diameter of 0-0.3 mm;
• time for complete drying - up to 2 days;
• consumption - 1.2 kg / sq.m with a minimum layer thickness.

In the assortment of the German company there are products of pasty consistency and powder. Also, the composition may include: acrylic, oil or gypsum.

Polymer putty Vetonit LR

Putty Vetonit LR is used to work in conditions with a minimum percentage of humidity. It is used for finishing concrete and plastered surfaces. As a rule, with its help, walls and ceilings are prepared for painting and wallpapering. The composition is distributed mechanically and manually. In the first case, a spatula with a wide working part is used, with which the builder independently regulates the thickness of the layer. The mixture is applied in one layer, this is enough for perfect alignment.

Separately, it should be noted that Vetonit LR putty tends to turn yellow with prolonged exposure to humidity. Therefore, it is applied exclusively to cleaned and primed surfaces. Also, the material is not designed to work with flooring.

This option has one variety of LR +, which consists of polymers and white limestone. It is also used only in dry rooms for processing various types of surfaces. When the powder is diluted with water, a homogeneous white consistency is obtained, which is able to retain its properties for up to 24 hours. The material is applied in a layer from 1 to 5 mm, where a smaller thickness is recommended for overall areas, and a larger one is vice versa.

Application area

The mixture is used to treat the following surfaces:

• concrete;
• plaster;
• drywall;
• foam concrete;
• expanded clay blocks.

Method of application and consumption

The product is applied with smooth movements in the direction from bottom to top. In this case, the temperature in the room should be in the range of 10-30 ° C. It is recommended to create good ventilation during operation. Consumption of Vetonit LR putty per 1 sq.m does not exceed 1.2 kg. The price of LR 25 kg is 700-800 rubles.

This is a basic cement putty that is successfully used in both wet and dry areas. As a rule, it is used before applying finishing putty or laying tiles. Also, the material is used to level the outer surface. The product is sold in three color variations - gray, light gray and white.

Universal for interior and facade work

Adhesion strength reaches 0.5 MPa. Separately, it should be noted the parameters of moisture resistance and frost resistance. The material is excellent up to 75 cycles of maximum freezing, which allows it to be used in regions with cold climatic conditions. 1 month after the creation of a layer of plaster, it is able to withstand a load of up to 6-8 MPa.

Main technical characteristics

Application area

It is used for preliminary leveling of the surfaces of internal walls made of mineral materials, concrete, lightweight concrete, expanded clay concrete blocks and bricks.

Method of application and consumption

The product is applied with smooth movements in the direction from bottom to top. The room should be at least 10 ° C, it is desirable to ventilate during application.

The composition is applied from top to bottom with smooth movements. The yellowish tint of the paste makes it easy to determine which area has already been treated and which is yet to be. Consumption of Vetonit TT putty per 1 sq.m within 1 kg of paste. The price of TT 25 kg is 450 rubles.

Vetonit KR - finishing putty for ceilings, walls. It is used to create a thin layer, which will then be covered with paint or wallpaper. Can be applied both manually and mechanically. The recommended layer thickness is 1-3 mm, while the consumption will be, as in the previous versions, 1.2 kg / sq.m.

Finishing white on an organic binder

Application area

To use the diluted mixture, 24 hours are given, after which the material undergoes solidification and loses its binding properties. Organic glue acts as the basis in the composition, so the material is ideal for organic surfaces in the form of drywall. It is not recommended to use the product:

• when working with flooring;
• for installation of ceramic tiles;
• in rooms with a high level of humidity;
• to remove seams.

Method of application and consumption

Before performing work, stir 25 kg of the mixture with 8 liters of water, for this you need to use a drill with a nozzle. It is important to remember here that it is the powder that is poured into the liquid, but not vice versa. After obtaining a thick homogeneous mass, which was achieved by whipping for 10 minutes, it is necessary to leave it to infuse for 20 minutes, then stir again intensively.

To perform the work, 2 types of spatula are used:

• small with a width of 30 cm;
• large - 70 cm.

The material is applied in one or 2 even layers, taking into account the complete drying of each. In the case of creating an optimal level of humidity in the room, as well as temperature and air circulation, one layer will dry in 2-3 days, after which you can safely proceed to decorative cladding.

All options for finishing putties have a single number of advantages. The list of advantages is quite extensive, which is why the Vetonit brand is in great demand among consumers. Among the features of the product should include the following factors:

• putty for exterior facade and interior cladding consists of environmentally friendly raw materials, due to which at different temperatures it is simply not able to emit harmful substances;
• the material has a high level of resistance to moisture, so the building material is successfully used in the construction of pools;
• facade putty with a snowflake symbol on the package suggests operation at low temperatures;
• the prepared consistency, previously diluted with water, can retain its properties throughout the day.

The rule for preparing a solution says that water is poured into the container, and a dry mixture is already added to the water. Not vice versa!

The advantages should also include the price of Vitonite, which is significantly lower than the competitive one. Despite the many positive reviews about the product, it also has disadvantages, which are:

• the need for preliminary preparation;
• the difficulties of application, this mostly applies to dry mixes;
• prolonged drying of the layers;
• the need for some experience in working with this building material.

VIDEO: Application rules and tips for working with the composition

Description.

Finishing putty Vetonit VH based on white cement and limestone is used for finishing the surface of walls and ceilings made of concrete, lightweight concrete, expanded clay concrete, brick, plastered surfaces, including the surfaces of plasters Vetonit TT, TTT, 410, 414. Putty Vetonit can to be applied to internal and external works for finishing of facades. The treated surface with Vetonit VH putty can subsequently be pasted over with wallpaper or painted with various water-based, latex or acrylic paints, or ceramic tiles can be glued onto it. When working with Vetonit VH putty, it is possible to apply it to the surface of walls and ceilings using such mixing and injection machines as Monojet PFT (G4), (G5). This putty Vetonit VH meets all the requirements of GOST.

Features and composition of putty Vetonit VH:

• Possibility of using Vetonit VH putty for indoor and outdoor use for finishing rooms with high humidity and finishing the facade of the building.
• When applying Vetonit putty by machine, high productivity is ensured, which is approximately 2-3 times more than in comparison with manual application of Vetonit putty on the surface to be leveled.
• When using Vetonit putty, a smooth, white and durable surface is provided on which, in the future, it is possible to stick ceramic tiles, wallpaper or paint with various water-based, latex or acrylic paints.
• The maximum layer for applying Vetonit VH finishing putty is from 1 to 2 mm.
• Low consumption of Vetonit putty, which is only 1.2 kg per 1 m 2 of the treated surface, allows you to save your material resources.
• Finishing putty Vetonit is made of environmentally friendly white cement and a lime component with a maximum filler fraction of up to 0.3 mm and gives the Vetonit solution increased adhesive properties of the solution. The composition of this Vetonit dry mixture does not contain harmful substances for human health and complies with all applicable hygiene standards and GOST standards in the Russian Federation.

Consumption of putty Vetonit VH:

The consumption rate of Vetonit putty with a layer thickness of 1 mm / m² is about 1.2 kg per 1 m 2. Depending on the professional skills of workers performing finishing work and without taking into account the loss of material.

Preparatory work and conditions for work with Vetonit VH putty:

Before starting finishing work with Vetonit putty, the surface to be treated must be thoroughly cleaned of bitumen, dirt, oil, dust, lime, grease, residues of mineral and organic paints and adhesives, as well as various water-soluble substances that prevent Vetonit putty from adhering to the treated surfaces, as well as as well as structurally bearing. If the surface is too dry before applying the Vetonit putty, it must first be treated with a Vetonit MD-16 primer. Primers to be applied Vetonit must be applied with a roller, brush, sprayer or brush. The primer used for surface treatment should form the necessary thin continuous layer up to 1 mm, but without allowing the formation of streaks on horizontal surfaces. Surfaces that have increased water absorption must be treated with a primer twice. The required quality of primed surfaces should be determined by the absence of water absorption into the treated surface. Re-contamination of primed surfaces is not allowed. Treated surfaces with a primer have a reduced water absorption and an increase in adhesive properties. When working with Vetonit putty and for the next 3 days, it is necessary to adhere to the temperature regime in the range from + 10 ° С to + 20 ° С. The base of the surface will be ready for applying Vetonit finishing putty on it only after the final drying of the primer mixture.

Preparation of Vetonit VH putty:

To work with a solution of Vetonit putty, it must be prepared with the following proportions: using mixing-pumping devices with a constantly dosed water supply, the proportion that is selected empirically. These proportions must be remembered so that further manufactured batches of the Vetonit putty solution are prepared with the same consistency. Immediately before starting work on applying the Vetonit putty solution to the surface to be treated and during the work, you need to constantly check the spreadability of the prepared Vetonit putty solution. When manually applying the Vetonit putty solution, it is prepared in the following proportions: 3.2 to 3.6 liters of drinking water at 20°C. To mix one 25 kg bag of Vetonit dry mortar, you will need about 8 to 9 liters of clean water from the drinking water supply. Vetonit dry putty mixture is poured into a pre-prepared amount of drinking water from room temperature and mixed for about 3-5 minutes using an electric drill with a nozzle or an electric mixer, with a maximum speed of these tools of no more than 600 rpm. . To obtain a homogeneous consistency with the prepared Vetonit putty solution, then the Vetonit putty solution is allowed to stand for about 5 minutes and then re-mixed, after which the Vetonit putty solution will be ready for use. The maximum time of work with the prepared mortar mixture of Vetonit cement putty mixture is about 3 hours at a temperature of 20°C. After completion of work in the next 3 days, you need to prevent direct sunlight, drafts and frost from entering the finished surface.

The procedure for working with the mortar mixture of the finishing putty Vetonit VH:

Vetonit putty can be applied both manually and mechanized. For continuous finishing of flat plastered surfaces, the initial layer of Vetonit putty solution is applied and leveled with a wide 800 mm trowel. With partial surface finishing, leveling can be done with a smaller trowel up to 300 mm. After that, the dried and hardened surface must be cleaned with special abrasive materials, and only after that it is possible to apply an additional layer of Vetonit putty solution. After the final drying of Vetonit putty from 1 to 2 days, the treated surface can be cleaned with a grinding tool (grater with sandpaper or sanding mesh). Before carrying out subsequent work and to increase the strength of the finished base, the surface must be primed with a Vetonit MD-16 primer.

Recommendations and precautions when using cement putty Vetonit VH:

When preparing the mortar mixture of Vetonit putty, an overdose of water is unacceptable, which can lead to a deterioration in the physical strength properties of the mortar mixture of Vetonit putty. And to increased shrinkage of the mortar mixture of Vetonit VH putty and can subsequently lead to cracking of the finished treated surface. In the process of working with Vetonit VH putty, it is necessary to regularly mix the prepared mortar mixture of Vetonit putty and not allow additional dilution of the mortar mixture of Vetonit VH putty with water. When setting Vetonit VH putty solution after the expiration of its application period, the additional introduction of water will not help, since the solution loses its adhesive qualities. When working with Vetonit VH putty, it is necessary to follow the instructions for general construction work, as well as safety precautions at construction sites.
When working with Vetonit VH putty, it is necessary to use construction gloves, and also avoid getting Vetonit VH putty into the eyes and skin. If Vetonit VH putty comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. Keep away from children!

Specifications for putty Vetonit VH:

Manufacturer's warranty and conditions of storage and transportation of Vetonit VH putty:

The manufacturer guarantees the compliance of the Vetonit VH putty with all the requirements in accordance with GOST 31357-2007, provided that the consumer observes all the conditions of storage, transportation and instructions of the instructions.
The manufacturer does not bear any responsibility if the consumer fails to comply with the technology for working with this material, as well as when it is used for purposes and conditions that are not provided for in this manual.
Deviation from net weight corresponds to GOST R 8.579-2001.
Vetonit brand products are approved for use in all types of civil engineering (Aeff< 370 Бк/кг; I класс материалов по НРБ-99-СП 2.6.1.758-99) «Нормы радиационной безопасности соответствуют (НРБ 99/2009)». Данную сухую строительную смесь Vetonit VH необходимо перевозить необходимо в крытых транспортных средствах и в соответствии со всеми правилами перевозки данных грузов.
Bags with Vetonit VH dry mix must be stored in covered, dry areas that ensure the preservation of the packaging and protect them from moisture. The shelf life of the dry mixture in the manufacturer's container is 12 months from the date of manufacture.

Finishing putty Weber Vetonit VH (Weber Vetonit BX)

DESCRIPTION:
Finishing putty waterproof, white, cement-based for leveling walls and ceilings indoors, as well as for facades

PROPERTIES:
- layer thickness 1-4 mm

- white surface
- preparation of the base for painting and wallpapering
- leveling the base before sticking ceramic tiles

PURPOSE:
- Alignment of walls and ceilings in dry, damp and wet rooms before:
wallpaper sticker,
- painting and leveling the walls before:
ceramic tile sticker
- as well as for fine leveling of plastered surfaces of facades before painting.

BENEFITS:
- For interior and exterior use
- white, smooth surface
- manual and mechanized application

SUBSTRATE PREPARATION:
The substrate must be solid, clean, free of dust and dirt. Substances that weaken adhesion such as grease, dust, etc. must be removed. If necessary, dry and absorbent surfaces are moistened. Windows and other untreated surfaces must be carefully protected.

MIX PREPARATION:
Pour 8-9 liters of clean water into a container and pour 25 kg (bag) of the weber.vetonit VH mixture, while the mixture must be added to the water, and not vice versa.
The recommended water temperature is 20°C. Mixing is carried out with a powerful drill with a nozzle for 3-5 minutes.
For better dissolution of the binder, the mixture is allowed to stand for 10 minutes. After slight re-mixing, the mixture is ready for use.
Mortar mix is ​​suitable for use within 3 hours from the moment of mixing with water. The temperature of the mortar mixture should be in the range from + 10 to 30 ° C.

APPLICATION:
The mortar mixture is applied by mechanized spraying or manually and leveled with a steel spatula. For full leveling, a two-handed steel spatula 80 cm wide is used, and for partial leveling, a small one, 30 cm wide. When leveling in several layers, it is necessary to apply each subsequent layer on the completely dried previous one (after 1-2 days). The dried putty surface must be treated with sanding paper and dedusted before applying the next layer. When leveling facade surfaces, it is recommended to apply the mortar mixture in 2 layers. The first layer is partial alignment and filling of pores. The second layer is a complete leveling of the surface.
In dry conditions, to ensure the necessary conditions for hardening, the leveled surface is moistened with water using a sprayer. After processing with sandpaper, the leveled and dried surface can be painted with alkali-resistant (cement-resistant) paint, wallpapered or tiled, after removing dust from the surface after sanding. To increase the wear resistance of the material and improve adhesion, 10% mixing water can be replaced with weber.vetonit MD16. When leveling old painted surfaces, weber.vetonit RF tile adhesive can be used as an adhesive layer or the base layer can be made with weber.vetonit 410 mortar. Facade surfaces can be painted with weber.vetonit420 and weber.ton micro V facade paints.

DRYING TIME:
The drying time of one layer of the recommended thickness is 1-2 days with good ventilation. Drying time depends on layer thickness, ventilation and temperature.
The level of 50% of the final strength is reached within 7 days at 20°C, with a decrease in temperature, the process of gaining strength slows down.

SPECIFICATIONS:
Color white, gray
Binder cement
Aggregate limestone
Maximum fraction, mm 0.3
Mixture consumption kg/m2/mm 1.2
Water consumption, l/kg 0.32-0.36
Water consumption, l/25 kg bag 8-9
Layer thickness, one application, mm 1-4
Application temperature, °С +10° to +30° C
Time of use from the moment of mixing with water, h 3
Drying time (one layer), days 1-2
Adhesion strength with concrete after 28 days, MPa, not less than 0.5
Compressive strength after 28 days, relative humidity 50%, +23°C, MPa 6-8
A set of 50% strength within, days 7

PRECAUTIONARY MEASURES:
When working, it is necessary to use rubber gloves, avoid contact with skin and eyes, in case of contact with eyes, rinse with plenty of water, keep out of the reach of children.

DISPOSAL INSTRUCTIONS
Dry mix and hardened material must be disposed of as construction waste. The material must not be released into the sewer.
Dispose of the paper bag as normal trash.

PACKAGING:
Paper bag 25 and 5 kg

STORAGE:
12 months from the date of manufacture, if stored in the original packaging in a dry place.