Finishing the apartment with artificial stone. Decorative stone in the interior: design options, photo. Working with decorative stone

Until recently, only the outer part of the house was trimmed with stone, but gradually it began to be used for interior cladding. Of course, the primary argument in favor of such material inside the apartment is its complete environmental friendliness and durability. But today, they rarely work with natural stone, porcelain stoneware or other imitation is more popular, which can be glued to walls or laid on the floor, and which does not require additional care.

Until recently, only the outer part of the house was trimmed with stone, but gradually it began to be used for interior cladding as well.

Stone in the interior

The use of decorative stone in the interior is due to a number of positive aspects, many of which are inaccessible to other materials. I see no reason to describe the disadvantages of such a cladding, since for different decorative imitations they will be individual, but the positive aspects are relevant for all options.

The use of decorative stone in the interior is due to a number of positive aspects, many of which are inaccessible to other materials.

Pros:

• Any artificial material weighs much less than its standard, which means that the load on the walls is reduced and it can be glued to tile adhesive without any problems.
• Almost all types of cladding, except, perhaps, porcelain stoneware, are resistant to mechanical stress and are very difficult to damage.
• Some materials used in the interior, such as liquid stone, are produced with the addition of dyes, despite this, it does not lend itself to fading and ultraviolet radiation.
• Finishing even a large apartment with a decorative stone will not take much time, and if you know how to lay tiles, you can do all the work yourself.
• Any artificial version is made only from natural materials without the use of chemicals, so it is completely safe, and you can use it even in the interior of a nursery.
• The stone finish is completely resistant even to large amounts of water. It can not only be washed, but also used for facing the bathroom or pool.

Finishing even a large apartment with a decorative stone will not take much time

Important! When choosing a material for an apartment, you need to take into account the individual characteristics of each room. This applies to both decorative aspects and microclimatic ones.

Kinds

The very concept of artificial stone is very general and includes a number of materials, some of which are sensitive to moisture or are afraid of sharp objects. In order to avoid mistakes in the choice, I will describe some of the most common options and their individual characteristics.

Stone finishing can be very diverse.

liquid stone

In fact, neither the word liquid nor the word stone describe this material. This is an imitation, which is made from a mixture of natural marble or granite chips and resistant polymers.
Liquid stone is completely insensitive to moisture and does not fade over time. It can not only be glued to the walls, but also used as a countertop in the kitchen. Thanks to the production technology, liquid stone can be of any size and thickness. From it you can create decorative elements in the interior or even put it on the floor instead of tiles.
In addition, liquid stone is cheaper than most analogues.

Liquid stone is completely insensitive to moisture and does not fade over time

Porcelain stoneware

Porcelain stoneware can rightly be considered the most famous and popular material for decorative cladding. As the name implies, porcelain stoneware is a mixture of red clay and granite chips, which are mixed, pressed and fired in a kiln at high temperature.
As a result of firing, the surface of porcelain stoneware becomes glossy, but this is precisely its main disadvantage. Such a surface is easily scratched, and it is very difficult to restore the damage.
Despite the fact that porcelain stoneware is a finishing material, it is rarely used in the interior of an apartment. In addition to the easily damaged surface, it has a rather significant weight, and it is very difficult to glue it to the wall.

Concrete or plaster imitation

Based on the production technology, this artificial version also fits into the category - "liquid". Concrete or gypsum mortar is poured into special rubber molds with a decorative texture. After complete drying and removal from the mold, a high-quality imitation is obtained.

Concrete tiles on the wall

Finishing with such a stone has a number of disadvantages that must be considered before starting repair work:

1. Gypsum is very afraid of water, and even if a protective layer is applied on top, it still cannot be glued in rooms with high humidity.
2. This finish is considered the most short-lived.
3. Imitation of concrete or plaster, needs additional painting, as without it the finish will look very unattractive.

Despite all these shortcomings, this artificial material is very often used in the interior of an apartment. It is largely due to its low cost and the possibility of independent production. In addition, it is easy to glue, and the total weight of the cladding is small.

Important! If you make concrete yourself, reinforcing additives and plasticizers must be added to the solution, which significantly increase the quality characteristics.

Plaster imitation

Conclusion

As you can see, stone decoration can also be very diverse. Not only the types of materials that repeat the forms of natural stone differ, but also the quality characteristics.
Before choosing a stone for a wall, you need to take into account many factors that will determine how long the new repair will last.

Decorative stones are a large exclusive group of finishing materials, which imitate beautiful stones with different textures created by nature. Quartblog explored how and where to effectively and functionally use this type of finish, and collected ideas for various interior styles.

General characteristics of the material

Some types of decorative stone contain natural ingredients:

• crumb of real stone
• sand
• cement
• gypsum
• glass
• mineral pigments to obtain the desired color.

At the same time, thanks to special production technologies, artificial decorative stone has a texture close to natural, less weight in comparison with wild stone, and looks beautiful in a residential interior.

Such materials are used in design projects for finishing any surfaces:

• brick and wooden walls
• working area of ​​the kitchen
• fireplaces
• even for the manufacture of exclusive sanitary ware

Consider what advantages different types of decorative stone have in individual cases.

What decorative stones look like: release forms and types

Decorative stone is available in different forms:

• Agglomerate
• Slab (large slabs)
• small tile
• Stone veneer in rolls or sheets
• Decorative mixtures, in most cases - based on concrete

Types of decorative stone

Slate

This is a stone that should be called "designer". Natural slate consists of several layers of minerals, between which there are veins and unique patterns.

For interior decoration, veneer or slate tiles are selected. The advantages of these finishing materials:

• slate slabs are light and at the same time retain heat well
• they are produced in different colors, close to natural - gray, burgundy, green, beige, pink
• you can create a solid stone wall.

And this finish is perfect. for a spacious living room.

Artificial marble (decorative concrete)

Natural marble is a material with unique shades and patterns. Artificial marble, or decorative concrete mixture, is made from a cement-sand mixture with the addition of marble chips or pebbles, and imitates marble stains. Release forms - slabs.

The advantages of such material:

• concrete DOES NOT conduct heat, therefore it is used even for finishing furnaces
• compared to real marble, the concrete finish is lighter and suitable for arches
• the surface of the material is easy to clean
• in the production of mixtures, any luxurious colors and shades are created.

Decorative concrete is used in the complex finishing of country houses, for facing halls, steps, sinks and bar counters, fireplaces.

Gypsum marble is a similar material. Its main binding component is gypsum. Thanks to fine polishing, the gypsum agglomerate is given a unique texture of marble or malachite.

Gypsum decorative stone is used to create a light and durable finish and maintain a pleasant microclimate in the room. Because it is successfully used for bedrooms or hallways.

Quartz Composite Stone

This is a decorative stone based on natural quartz, with the addition of pigments. Large solid countertops or large slabs are made from the material.

Quartz slabs have many advantages:

• moisture resistance
• resistance to temperature extremes and mold
• antibacterial properties
• ease of care.

In general, it is a practical and suitable material. for finishing the bathroom, working area of ​​the kitchen.

In addition, it is used for the manufacture of sanitary ware and wall cladding of swimming pools.

acrylic stone

Artificial acrylic stone - a similar composite of acrylic resins with the addition of natural minerals and pigments.

Acrylic is known for its use in medical equipment. It is a hygienic antibacterial material. In addition, it has the same advantages as quartz stone and is easily restored.

Acrylic stone is successfully used in interiors for the same purposes as quartz stone. Acrylic plumbing considered prestigious.

Porcelain stoneware (porcelain tiles)

Porcelain stoneware is one of the most popular facing materials. It is produced by pressing and firing several types of clay, it contains mineral chips and dyes.

Porcelain tiles withstand heavy loads and high humidity. And this is the most practical stuff. for finishing floors in halls, corridors. Plus it applies for complex finishing of bathrooms.

Tadelakt, or Moroccan plaster

And finally - the most exclusive finishing stone. The name itself indicates that the material is designed for decoration of bright Moroccan houses and for interiors in oriental style.

Moroccan plaster is a liquid mixture of clay, quartz sand, ash, marble flour and lime, and may contain henna or other natural dye. And it has a lot of advantages over concrete mixes:

• natural and absolutely harmless composition
• when applied, it can be given a beautiful texture with a roller
• it does not attract dust
• it is a very durable material.

In oriental interiors, tadelakt is used instead of wallpaper, for finishing any walls.

About what other interiors you can use decorative stone - more.

Decorative stone and interior atmosphere: what style welcomes such a finish

There are two types of decorative stone finishes. Each of these types transforms the situation in its own way.

1) textured finish, with embossed surface which looks like a real stone wall.

This cladding emphasizes the ethnic features of the interiors. With moderate use, it helps create a cozy classic atmosphere.

2) Smooth glossy finish, polished stone.

Decorative stone with a smooth surface and natural pattern - porcelain stoneware or quartz composite - makes the living space more modern and comfortable. This is a great backdrop for an interior in style. high tech or minimalism.

The first type of finish radically changes the interior. However, a textured decorative stone can be used for an entire wall, and for decorating a separate area of ​​a room, a fireplace, or interior openings. Therefore, designers approve of such material when choosing different styles.

Let's take a closer look at the examples.

Ecostyle, based on a combination of natural materials, favors stone finishes instead of wallpaper, panels, and textured stone coasters and figurines.

In addition, decorative stone is very welcome in ethnic interiors.

in colorful Arabic style stone is used to create interesting accents. Decor can be made from it on door and window openings, niches and plinths.

In addition, in spacious oriental living rooms, the accent wall can be decorated with light stone slabs or decorative plaster. AT Moroccan interiors often all the walls are finished with tadelakt.

African style even more festive, and only he allows an abundance of stone. In such an interior, several walls can be finished with rough shell rock, sandstone or stones with a similar natural texture, red, terracotta or green. Stone souvenirs and figurines will complement the style.

AT japan house style there is a special love for the stone. At the same time, excesses and pompous stone decoration in the spirit of a medieval castle are not allowed in the Japanese interior. A small decorative brick or slate is only used to create a wall art or an interesting accent, but it looks chic.

AT country style (rustic style) one of the main markers is the combination of wood and stone. At the same time, in the Russian country, an unprocessed large stone is welcomed in the decoration of a fireplace, a kitchen apron.

And in ethnic scandinavian interior the decoration in the spirit of a loft, made of decorative bricks, looks harmonious. It is only important to choose a white or beige textured material that will make the room more spacious.

In the room loft style one or more walls can be decorated with similar brick slabs or decorative concrete.

Finally, another option when a rough decorative stone can be used with virtually no restrictions is design. castle-style country houses.

In this style, combinations of stones of different sizes and with different textures are appropriate. Moreover, the abundance of natural stone emphasizes the prosperity of the house.

In most cases, decorative stone, close to natural, is associated with old ethnic traditions, wealth and a popular eco-movement. Plus, it can fill the house with special energy.

Let's move on to how it looks in the interior of different rooms.

Decorative stone in the interior of the living room

In the spacious living room, with the help of decorative stone, zones can be distinguished: a dining area, a lounge area, a TV wall or a false fireplace.

It is very useful to use such a finish near the TV panel - natural colors and textures reduce eye strain.

In a classic English living room, a decorative stone in the fireplace trim is almost an indispensable element. At the same time, luxurious classics favor gypsum and marble imitation.

In the working area of ​​\u200b\u200bthe kitchen, a smooth stone looks as harmonious as possible - quartz, acrylic. A countertop or apron made of such material may resemble marble products.

If you use slate or stone in a brick variation to finish the wall near the gas hob and hood, you will create the atmosphere of a cozy country house with a fireplace in the kitchen.

The dining area can be elegantly defined and made visually spacious with light faux marble or veneer mosaics on the wall.

Decorative stone in the bedroom interior

The atmosphere of the recreation area will emphasize the decorative stone of warm light colors, with a relief surface.

With this finish, you can highlight the wall at the head of the bed or create a stone panel.

At the same time, different types of decorative stone are suitable for bedrooms in country style, oriental, Mediterranean.

Decorative stone in the interior of the nursery

In the children's room, a decorative stone will help to realize interesting design projects. For example, smooth stones can be used to create three-dimensional panels and makeshift castles in the play area.

With the help of such a finish, you can also highlight the working area of ​​\u200b\u200bthe child.

Decorative stone in the interior of the hallway

A small corridor or hallway can be visually expanded with strips of decorative stone. Plus, imitation of brickwork or slate will allow you to design this area in the style of old European streets.

The effect will be complemented by a stylized banquette, sconce-lanterns, wall flowers.

But remember - the smaller the room, the less masonry you need to use.

Decorative stone on the balcony

On a balcony or loggia, decorative stone trim is used to:

1. keep warm
2. create a cozy environment for relaxation and tea drinking.

In addition, a spacious balcony can be decorated in the spirit of a European cafe, greenhouse. To implement the most interesting ideas, a rough textured stone is suitable.

Decorative stone in the interior of the bathroom

For the design of bathrooms and toilets, smooth decorative tiles with a uniform structure are traditionally used - ceramics, porcelain stoneware, quartz composite, and concrete marble.

The drawing of the finishing material can emphasize the chosen style.

At the same time, natural pebbles will complement the eco or marina style.

How to choose a decorative stone: criteria

• The main components from which most types of decorative stone are made are cement, sand, fillers and additives and pigments. The strength of the stone depends on the brand of cement and the ratio of cement and sand. Stone from imported durable cement and quartz sand cannot be cheap.
• The surface of a quality stone is uniform. If holes, cracks form, and the stone crumbles, the mortar production technology has been violated.
• Only natural, non-toxic binding additives and dyes should be used in interior decoration products. Therefore, ask the seller for which surfaces the presented material is suitable.
• Subject to the production technology, colorants are added to the solution during kneading, and the stone is stained evenly.
• Note: a high-quality decorative stone has the same color on the front surface and ends, there are no traces of peeling paint and streaks. If the material meets the standards, sawn samples may be presented in the store.
• And finally - before buying, consider different samples of the collection. They should have the same thickness and a repeating pattern.

Features of laying decorative stone

Installing decorative stone tiles or veneer requires simple preparation and a little imagination.

We list the main stages of work.

1. Thoroughly clean and prime the surface before laying.
2. Then it is desirable to make an even marking on the wall: use the level to draw horizontal lines. The distance between them should be equal to the height of the stone.
3. Lay out the products on the floor and think over the laying pattern that should be created on the wall. It is advisable to alternate short and long elements.
4. Then glue each stone, guided by the created scheme. To do this, you can use silicone sealant or liquid nails. Lay from the bottom row and from the corners.
5. In order to correct the shape of individual plates, use a wood saw, a diamond-coated grinder, a miter box or a chisel for curly carving. You can clean the edges with sandpaper.

6. 

   

   

   

   

   

   

   

   

   

   

   Quartblog Digest

   How to combine different textures in the interior - The combination of different textures in the interior is an art. A little bit about how to know it and what to focus on when choosing materials for the Kvartblog was told by an interior designer.

   Do you want to admire the marble pattern without paying a round sum for the material itself? We will show you how to do it. 8 budget marble imitation options - the choice is yours!

   Let the pristine beauty of natural stone into your home! The quarterblog will talk about the advantages and disadvantages of natural stone in the interior and show beautiful examples with photos.

   We invite you to look at 25 successful examples of the use of white brick in the interior: from the bedroom and living room to the bathroom and corridor.

   Many people like the loft style, but they are not ready to completely decorate the space in an industrial style. Then the main element is used - a brick wall.

   This feminine interior of an apartment in Stockholm has a surprising amount of industrial features. The main one is a brick wall found under the old finish during the renovation.

Designers continue to rely on the natural texture and raw materials. In view of this, the decorative stone is their favorite, non-secret "weapon". It is, for the most part, completely natural and has an expressive, self-contained aesthetic.

How, in this case, does a decorative stone differ from a wild, natural one?
The fact that it is produced by a person using special mixtures and forms. At the same time, the drawing of the product repeats in detail the section of natural analogues. That is, artificial stone is a worthy replacement for travertine, slate, granite and many other rocks and minerals.

Types of decorative stone and production technology

They learned to make artificial stone a long time ago. Masters of the Middle Ages added crumbs of tuff, dolomite, marble to the concrete solution, obtaining a durable, noble building material.

Today, artificial stone is a rather light tile, which is pressed from a wide variety of compositions. Depending on the main components, a decorative stone can be:

• plaster,
• ceramic,
• concrete,
• acrylic,
• polyester.

In addition, the market offers a "liquid" stone in the form of spraying, which is used to cover countertops and bar counters. As well as flexible stone veneer: they decorate not only walls, but also furniture facades, countertops.

Specific additives impart additional properties to the facing stone. For example, volcanic perlite increases anti-corrosion, and expanded clay or pumice facilitate the product. When soot and iron oxide are introduced into the composition of the mass, a fashionable aged stone is obtained.

Despite the abundance of textures, decorative stone tiles are produced in almost the same way: the selected solution is poured into matrices, tinted, sometimes fired, coated with impregnations or glazes. The process is simple, it can be adjusted at home by buying a special silicone mold.

For outdoor work, concrete-based slabs are most often used. And inside, they mainly use an artificial stone made of gypsum, an environmentally neutral mineral substance.

Advantages of decorative stone

All types of artificial stone combine these qualities:

1. availability, relatively inexpensive finishing material;
2. ease of installation;
3. unpretentiousness in care;
4. resistance to mold, fire;
5. durability (manufacturers give a guarantee of at least 10 years);
6. an impressive range of shades and textures.

If the stone is made of gypsum, clay, sand, then add environmental friendliness and hypoallergenicity to this list.

Features of the use of artificial stone

Due to the variety of patterns and colors, decorative stone is a real “must have” for a modern interior.

If you use a stone, it becomes less insipid, - more diverse, and - more convincing, and - much more comfortable.

Many are hard to imagine without facing stone. For example, in a Mediterranean house, this is a stylization of pebbles or boulders polished by the sea. In the Alpine - under the mountain debris. In the interior, Provence - under the sandstone, burnt out in the sun. In English - under a strict cherry-colored brick.
An artificial, glossy stone has made its way even into this "patrimony" of metal and glass.

The stone, of course, is a unique tool for creating an extraordinary environment, but you should not go all out. If you finish the walls with stone tiles from top to bottom, you get a crypt, a wine cellar, a dungeon ... But not a living space.

Facing with decorative stone solves several problems. First, it is picturesque, elegant and prestigious. Secondly, with the help of a stone, you can make it more voluminous, expressive.

In the hallway, tiles are usually used, stylized as limestone, sandstone, brickwork.

Decorative stone looks more spectacular when combined with other types of finishes - plaster, wood paneling, embossed wallpaper.

In the hallway, stone tiles are used, for the most part, for fragmentary cladding. Corners, doorways, sections of the wall around the dial, mirrors, paintings, hangers are emphasized with decorative clinker, sandstone, quartzite.
By the way, if a wall covered with chipped stone is supplemented with a large retro clock, a “street” bench and a lamp a la a lantern, you will get a soulful city “lane” leading to the depths of the apartment.

The stone is associated with reliability and safety. If he is present in the living room, the household feels more confident, "like behind a stone wall."

And the stone is also associated with fire, with the warmth of the hearth. The memory of the tandem of a fire and a stone was carried by a person from cave times, it is not for nothing that fireplaces are still covered with rubble and cuts.
However, not only fireplace portals are decorated with granite, brick or shell rock tiles.

Niches with lighting, shelves, glass showcases, a fragment of a wall with a TV panel or behind a sofa are lined with decorative stone.

Decorative stone absorbs a lot of light due to its structure. Therefore, designers are advised to alternate it with light plaster or wallpaper. Remember also that artificial stone decoration will require additional fixtures and a well-thought-out lighting scenario.

A decorative stone is especially good in a studio apartment. Perhaps this is the easiest, most budgetary, most relevant way to divide a home into locations.

Decorative stone in the bedroom

Here, the stone will become a talisman: it will soothe, lull, evoke memories of something native, truly natural.

A massive, solid bed is ideally combined with walls covered with decorative bricks, as well as with wooden beams, caissons, sconces in the form of candelabra.

In the bedroom, it is better not to use stone tiles with a glossy surface to avoid the “cold”, disturbing shimmer. And do not forget to emphasize the fragment lined with stone with lamps, which will make the texture softer and warmer.

Usually, a wall behind the head of the bed or a corner with a dressing table and a mirror is decorated with stone. Unlike the hallway, where the transitions from stone to plaster are carried out using torn edges, overflowing, other, less noticeable techniques are used in the bedroom. For example, they designate masonry with moldings.

Decorative stone in the children's room

Environmental friendliness, safety of artificial stone tiles provided her with a pass here.

It is also important that with the help of a stone you can embody the plot of your favorite fairy tale. Let's say, create a "princess castle", "Ali Baba's cave", "dwarf's dungeon", "underwater grotto".

It is easy to lay out mosaics, panels with artificial pebbles, paint pebbles under snails and ladybugs, decorate a landscape on the wall with a frame of stones, a niche with toys.

If we are talking about a teenager's room, then the artificial brickwork at the desktop will discipline, call him to order. And echo with more adult toys - car models, a globe, steampunk gizmos.

Decorative stone in the kitchen / dining room

There are a lot of methods to successfully integrate stone into the kitchen space. For example, imitation of rustic masonry above the hob turns this working segment into a colorful Russian stove or an ancient fireplace.
And kitchen niches covered with decorative stone will make the kitchen look like an old cafe, especially if they are combined with brutal countertops and cast-iron utensils.

For the kitchen, choose stone tiles impregnated with protective compounds. Porous, loose products absorb water and are more difficult to clean.

It is not forbidden to use decorative finishes in the context of cutting-edge interior styles. The embossed stone of a reddish-brown, greenish hue goes well with glass and metal, sets off the brilliance of kitchen appliances, makes the loft and high-tech more cordial, chamber.

Decorative stone in the bathroom

A natural pool carved into the rocks - this is what a stone-tiled bathroom might look like.

In the design of a house and apartment, I want to use natural materials, but this is not always justified. For example, the use of natural stone for interior decoration. It is expensive, difficult, and requires high qualifications. There is a very similar to natural artificial stone. It is also made from natural ingredients, but it weighs several times less and costs much less. Moreover, decorating the hallway with decorative stone can be done by hand - its installation does not require special qualifications.

One of the options for decorating the hallway

Types of decorative finishing stone

Today, there are three types of decorative artificial stone used for interior decoration:

• based on cement;
• based on gypsum;
• agglomerate.

In appearance, these products are very similar to natural stone, only they weigh much less (from 14 kg / m 2 to 50 kg / m 2). The cost is also much lower (compared to natural), especially if the manufacturer is Russian or Belarusian. The pluses include easier installation - only the front part is textured, the other three are more like tiles or bricks.

Actually, there is another type of decorative artificial stone - clinker tiles that imitate various types of brickwork. It is made from clay almost according to brick technology - it is fired in a kiln and glazed. The difference in thickness is 1-3 cm. This type of finish is good in many - from high-tech to.

Gypsum based

Gypsum finishing stone is the most inexpensive of this type of material. Its second plus is that it is the lightest. It is he who is used when mounting on drywall, since he simply cannot withstand heavy loads. Cons - it is rather fragile, hygroscopic, and can collapse when wet. Finishing the hallway with a decorative stone based on gypsum is possible only if, after laying, it is treated with a special protective impregnation or acrylic-based varnish.

The format of gypsum tiles can be any - a very plastic solution allows you to get any surface and shape Light shades in the hallways do not "press" and do not add heaviness Heterogeneous color gives additional volume and charm Gypsum decorative stone in combination with a gypsum panel in the corridor - oriental style

Based on cement

A strong and durable finishing stone is obtained from a gypsum-sand mixture. It can be washed, even with a brush using liquid detergents. Its disadvantages:

• Hard to cut. You will need a grinder with a diamond disc so that there is less dust, you can moisten the tile.
• Big weight. This is when compared with a gypsum counterpart, and compared to natural weight is more than two times lower.
• higher price. In the manufacture of cement decorative stone, high-quality cement is used, but it costs decently. In addition, the production technology affects the price - cement takes longer to gain the required strength (28 days), and the molded tiles must be stored somewhere until this moment, and under certain conditions (at a temperature of about 20 ° C and sufficient humidity of 40-50%). This means that significant areas are needed for storage facilities, and these are additional costs.

All these shortcomings are compensated by durability and ease of care, so this is one of the most common decorative stones for interior and exterior decoration.

You can completely lay out the walls in the hallway with decorative cobblestones. Light gray - the most for a small hallway

Artificial stone from agglomerate

This type of finishing decorative stone has appeared recently. It consists of natural rocks crushed to crumbs - marble, granite, quartzite - to which polymer resins or cement are added. To obtain bright colors, a coloring pigment is added. Such a decorative stone looks great - interspersed with natural fragments, reflections on the edges of the crumbs ... It really looks good, suitable for finishing work in rooms.

Coloring methods

When choosing a collection of gypsum or cement, pay attention to the method of staining. The pigment can be added to the solution, and then the whole tile will be of the same color. Shading tones are then applied to its front surface, which give the surface a more natural look. With this technology, even with a chip, the difference will be imperceptible, since the shades are close.

In another embodiment, the pigment is applied only to the surface. Then, if it is chipped or cut, the color will be very different.

Do-it-yourself artificial stone laying

Before starting work, you need to determine the quantity. It's not as easy as it seems. If you look at the collections, you will see that they mostly consist of fragments of several sizes and shapes. The exception is ceramic stone and collections imitating brickwork. Knowing the size of the fragments, you can figure out how you want to arrange them.

Outline the proposed borders of the finish on the walls. Now you can more or less accurately calculate how many "squares" of decorative stone you need. Add about 10-15% to the resulting figure - for trimming and possible changes in the process. This will be the required amount for finishing.

Pre-layout

Masters who have experience working with decorative stone first “figure out” where to place which fragments, how to turn them. You can make the layout on the floor, you can - in design programs (if you know how to work with them), you can try to draw a plan on a graph paper or a piece of paper in a box. The main condition: it is necessary to observe the proportions and do not forget about the seam. It can be quite small - this type of installation is called seamless or continuous, or it can have a thickness of up to 1 cm or even a little more.

Many people skip this stage when decorating walls with decorative stone on their own, hoping that everything will become clear in the process of work. It is possible, of course, and so, but keep in mind that the glue seizes very quickly and there is very, very little time for rework. The plan will make things easier.

Surface preparation

You can finish with artificial stone walls from any material, but they all require preliminary preparation. If the walls were previously finished with something, the entire finish is removed, a bare wall with plaster should remain. Gluing a decorative stone on old wallpaper is a waste of time and money: the finish will simply fall off. Some very light collections can be glued onto wallpaper, but these can only be fragments - a few tiles. And then, no one will guarantee that the wallpaper will not tear and everything will not collapse.

The easiest process for preparing walls is if they are plastered. Just cover them with primer. Its type is selected depending on the material (gypsum or cement). Then you can proceed to the actual finishing.

If the walls are made of bricks, building blocks, or any other similar material, they are first primed, then plastered with a suitable plaster. Drywall is also allowed. But at the same time, you greatly limit yourself in choosing a finishing stone - you will need to choose from the lightest collections in terms of weight, and this is mainly a decorative stone made of gypsum.

If the walls are wooden, they are first coated with waterproofing impregnation, after drying they are treated with a primer. Then a paint grid is nailed to the surface and only then plastered. When choosing a plaster, it is advisable to choose from those that "breathe" and will not interfere with the wood to regulate moisture. With glued tiles, this will be problematic, but the decoration of the hallway with decorative stone is usually fragmentary - the tiles are glued only in some places, and the rest of the surface will remain vapor-permeable.

What to glue

Most manufacturers of decorative stone advise using special adhesives designed specifically for working with this material. They are of three types:

• for lightweight finishing stone weighing up to 30 kg/m 2 ;
• for heavy from 30 30 kg / m 2 and above;
• for low temperatures (below +5°C).

It is necessary to dilute the glue in small portions, strictly following the recommendations of the manufacturers. It is better to stir with a drill with an appropriate nozzle - it is easier to achieve uniformity.

You can also glue on good quality tile adhesive, only it must be really good - you will have to keep a decent mass. The third option is for liquid nails. This method works great on drywall, with plastered surfaces it is better to use an adhesive solution.

Sticking technology

Plastered or plasterboard-leveled walls are coated with a primer. While it dries, dilute a portion of the glue. When laying, it is important that the rows of finishing stone are laid horizontally. To achieve this, markings can be applied to the wall. This can be done with a paint cord, or you can draw with a pencil using a bubble or.

Laying decorative stone in the hallway starts from one of the corners. Some collections have special corner tiles that are easier to work with. If there are no such fragments, you will have to decorate the edges with “end” fragments. They are in some collections - their edges are also painted. The same elements are used last in a row where it is necessary that the ends have a decorative look.

Before laying, the back of the decorative stone tile must be inspected. There may be remnants of cement milk - this is a thin, foamy coating of light color. It must be removed. This can be done with a stiff brush.

If the air temperature is high or the humidity is low, the back of the stone is moistened with water. Then, a layer of glue is applied with an ordinary spatula, leveled, and the residues are removed with a toothed one (with a tooth of 4-5 mm).

The fragment is pressed against the primed surface, moving it slightly from side to side, making close contact with the wall, and placing the fragment in the desired position. You can knock on the surface with a rubber mallet for better adhesion.

This option of laying the finishing stone on the walls requires a significant amount of time. It is used when it is required to lay only a few tiles or along the edges of a large fragment. If you need to lay a significant amount, it is easier to apply glue to the wall, and also remove the excess with a notched trowel. And press the tile moistened with water to the glue on the wall.

Otherwise, the entire sequence of actions does not change.

If the masonry is seamless, the next element is installed closely. If a seam is needed, the distance between the tiles is fixed with plastic, wooden wedges of the same size, pieces of drywall are also suitable. If the seam is small, you can use plastic crosses.

When working, glue can be squeezed out from under the tile. If it gets on the front surface, it must be removed immediately. Concrete finishing stone can be used with a damp cloth, gypsum - only dry. The glue sets very quickly, and then it is almost impossible to remove it without damaging the surface.

According to this principle, the planned volume of finishing is laid out. When the glue sets (indicated on the package), you can start filling the seams.

Grouting

A special compound is used to fill the seams. In color, it can imitate masonry mortar or be in contrast to the color of the finish.

The composition is diluted with water to a pasty state (the proportions are indicated on the package), put into a special syringe or a tight bag with a cut off corner. The paste is squeezed out between the seams. Depending on the type of finish, the seam is filled almost completely or only halfway (up to 5 mm can remain to the edge of the tile). The result is either relief masonry, or more even.

Until the grout has set, they take a special joint and level the seams, giving them a convex, concave or flat shape.

Photo options for finishing the hallway and corridor with decorative stone

Finishing the hallway with decorative stone is often the decoration of corners and doorways.

What is good about this option - all the "dirty" places are covered with stone

Decorative stone in the hallway is the most reasonable solution. The original wall decoration in the hallway with decorative stone will give the interior a uniqueness, allow you to beat possible corners and niches, doorways and built-in wardrobes. Thinking over the repair of an apartment, they usually start the hallway last, believing that fantasy is not appropriate here.

Benefits of using decorative stone

Most often, the hallway is a narrow enclosed space, in extreme cases, having only one blank wall. The rest of the walls are decorated with doorways.
Where is the imagination here? Although, this is a moot point. In addition, an amazing sense of security arises at the sight of such a finish.

• Stone tiles are quite light, formed in the form of regular geometric shapes, which simplifies the creation of even masonry.
• Artificial stone is not subject to decay, the fungus will not grow on it, however, it is an environmentally friendly material, since it does not contain harmful substances.
• Caring for this type of finish is easy, any detergent will help.
• The special strength of artificial stone makes the hallway decoration optimal, because this is the most visited part of the apartment and its walls are subjected to unnecessary stress.
• The ability to choose not only the shape of the stone, but also the color scheme will allow you to fit it into any interior.

If you combine it with glass or metal, placing green plants nearby, then the interior looks stylish and cozy, but good lighting is required. The artificial stone decoration of the entrance hall is perfectly combined with the transition to the kitchen. The joint styling of this tandem will make the interior softer, more fluid.

Design solutions

The applicable methods of interior design of the hallway include: the ability to lay out the entire wall, or finish only part of it. Separate elements of the hallway will become more expressive.
Decorative wall decoration in the hallway looks natural, fresh, at the same time rich and elegant. You need to choose a decorative stone or artificial decor, focusing on its price.

Advice. Visually pushing narrow walls, giving them the original antiquity of medieval palaces, will allow a bas-relief light stone.

• The use of shell rock with small coral inclusions in the design, together with a rough stone chipping, delights lovers.
• A wall completely finished with stone acquires a heavy, oppressive effect.
• The stone design looks amazing in combination with stretch ceilings, thick wallpaper, and simple plaster. The artist's imagination is the only limitation.
• The combined decoration of the hallway with stone and tiles is more functional, looks more organic, allows the use of underfloor heating, which creates additional comfort. Of course, a decorative stone looks more solid than an artificial decor, but it is also more difficult to care for it.

The peculiarity of the manufacture of artificial stone allows you to make tiles of various shapes, used in decorating curved surfaces of arches, doorways.

How to install

The laying of stone elements is quite simple. Therefore, decorating the walls with decorative stone in the hallway is quite feasible with your own hands. A small percentage of self-confidence, minimal finishing skills, a few video lessons or master classes, and nothing is impossible.

The preparatory work involves the complete cleaning of the walls from wallpaper and old plaster. The location of electrical wiring, switches, lighting should be foreseen in advance. If there is no need to form arches, then the alignment of the walls can be done using putty.

Advice. It is necessary to level each surface, the more carefully this is done, the easier it will be to mount the decor.

The walls are perfectly leveled with drywall. It allows you to use built-in lights, LED lighting, which makes the decoration of the hallway with artificial stone more original.
The tile is fixed with special glue, "liquid nails", putty mortar.

Practice shows that the adhesive composition is the most optimal. Sometimes it becomes necessary to fill the seams with a special solution.

Phased work, instructions

Self-finishing with a decorative stone of the hallway involves the following work order:

• We completely remove all old finishing materials. We remove the opened defects and cracks on the walls with the help of solutions. It is necessary to plaster only those surfaces, the irregularities on which exceed 5 cm per square meter.
• Putty finally level the entire surface of the wall. We apply a primer.
• Wall marking is necessary for installers with a minimum skill in finishing the hallway with stone and tiles. For this, beacons are used. These are specially installed stones from which the masonry is counted.
• It is better to place the beacons on the bottom row of tiles. Pulling the cord, use the level to determine the horizontal line.
  The bottom-up laying technology from the corner is the most convenient. Row after row, climbing up the wall, carry the cord, as the tiles may differ slightly in size and the pattern is deformed.
• Be sure to consider the location and width of skirting boards and cornices.

Installation of decorative stone

• Before directly mounting the decor on a wall or other surface, sort the stones (shades may vary slightly even in one batch). Take your time and lay out the future decor element on the floor.
  So the masonry is immediately visible, and it will be quite difficult to get confused during installation.
• Laying tiles is carried out according to the instructions for a particular finishing material. More bulky decorative stones or large artificial tiles are fixed with adhesive solutions. They must be applied directly to the tiles with a notched trowel.
• "Liquid nails" are effective with a small size of artificial stones.

Related video: ARTIFICIAL STONE in the interior ❖❖❖ Decorating the hallway with decorative stone
Advice. Fitting tiles to one size is easy. Artificial stones are easily sawn, undermined, cut. Using a hacksaw or pliers, you can slightly correct the defects.

After finishing laying stone tiles, leave it for at least a day to dry. It is possible to process the resulting seams with a grout composition only after that.

Source: otdelka-expert.ru

Artificial stone in the interior of the hallway (photo)

Why choose artificial stone in the hallway? Compared with natural stone, artificial analogues have a number of advantages.

1. Light weight, which is very important in the processes of transportation and practical use.
2. High strength. According to this indicator, an artificial decorative stone is not much inferior to a natural one, moreover, in some cases it is even stronger and is able to serve as a facing material for more than a dozen years.
3. Like natural artificial stone, it is not combustible. And, finally, artificial stones are easy to install and, in terms of the laboriousness of this process, are not much more difficult than laying traditional ceramic tiles.

Varieties of artificial stone for the hallway

Today, all artificial stone, based on the technological features of manufacturing, is divided into two groups: stone based on colored concrete and stone based on gypsum. Visually, these finishing materials are almost impossible to distinguish.

But if you pick up a sample, it becomes immediately clear that artificial stones made on the basis of concrete are much heavier than gypsum counterparts. In the price range, concrete-based stones are a little more expensive (about 100-150 rubles per square meter). The only disadvantage of gypsum stone is its moisture resistance, gypsum is afraid of water.

But now a lot of options have been developed for facing gypsum stone coated with a special waterproof composition, in extreme cases, water-repellent impregnation can be applied independently.

Do-it-yourself artificial stone laying in the hallway

Having decided on the design, you can accurately calculate the amount of stone that will be used. The modern industry, specializing in the production of building materials, produces facing stone of various sizes and shapes, greatly simplifying the task.

First you need to prepare the surface for finishing with facing stone. The wall must be leveled and puttied, turning the surface into a perfectly flat one without potholes and protrusions. For better adhesion, it is recommended to prime the surface. After the preparatory work, you can begin the installation process.

It is best to draw the intended pattern on the wall with a pencil. Laying starts from the bottom, from the floor, it is recommended to use a level in the work. Liquid nails for lightweight artificial stones can be used as a fixing solution.

For heavy concrete stones, it is recommended to use ceramic tile adhesive. Since the glue hardens quickly enough, it is recommended to cook it in small portions. The last stage of laying is grouting, after which it is recommended to treat the lined surface with varnish.

Ideas for artificial stone in the decor of the hallway

Despite the fact that the stone is classified as a very characteristic material, designers recommend adding some finishing touches. In particular, it is proposed to highlight the contour with darker paint, this will give the masonry additional volume.

Spotlights that capture the texture of the stone are very effectively combined with stone cladding. It is also possible to include mirrors and green plants to create a complete picture of the design in the hallway.

Source: decorwind.ru

Decorative stone in the hallway: interior design photo.

Decorating the hallway with artificial decorative stone is an expensive pleasure. But after you see the transformation of your apartment, you will forget about money. The result is worth it.

To create a masterpiece of art from an apartment, you can “use” all your imagination. If desired, you can discuss the details with the designer, who will select the optimal type of installation, as well as the shape of the stone. Finishing material has a wide range of colors and textures. It is quite lightweight and versatile. The stone can be used to decorate both the hallway and any other room.

It goes well with tiles, stucco decoration, wallpaper and various types of stretch ceilings. And this, in turn, allows you to roam your imagination when combining various finishing materials. Making a hallway with a decorative stone will not require much effort from you, since among a large number you can highlight decorative elements, rounded and corner inserts necessary to decorate door niches and openings.

With the help of decorative stone, you can finish absolutely any surface: concrete, brick, metal elements, and so on.

How to make a decoration yourself?

The first thing to do is prepare the foundation. It is necessary to remove the previous finish, which has ceased to hold tightly: tiles, plaster, wallpaper. If the wall has irregularities, with a surface difference of more than five centimeters, it will be necessary to prime and plaster.

The next step is wall marking.. After this, the guide stones are fixed. When marking, it is necessary to take into account the height of the skirting boards and cornices. Now you need to make a check mark. For these purposes, any corner of the hallway is perfect. You can choose any height. To make a mark, you will have to use a laser level, or a water level, and then transfer it to other corners.

After creating the label. it is necessary to measure the distance between it and the first level of decorative stones. You can also install risks or hammer nails in the corners, between which then pull the rope. Decorative stone can also be laid back to back. It is important to lay the stone in even horizontal rows. To apply glue to a wall or stone, it is enough to use a comb trowel.

The last step - rubbing the seams. This must be done in exactly one day. Just during this time, the glue will grab. To grout the seams, use a special compound for grouting.

Source: en-remont.com

Finishing the hallway with decorative stone: types of coating

Before starting work, it is necessary to choose the right finishing material. Artificial stone is made on the basis of concrete and gypsum with the addition of dyes. Both types have their own advantages and disadvantages, so it is better to study their characteristics first.

concrete stone

The advantages of concrete products include:

• high strength,
• durability,
• moisture resistance,
• variety of textures and colors.

Walls finished with such a stone can be easily cleaned of any dirt, and a worn surface can be quickly restored with paint. If you accidentally touch the finish with something hard, it will not leave marks and cracks will not appear.

• big weight,
• high price,
• the complexity of processing.

In order to cut individual fragments when laying, you will need a grinder and a diamond wheel, as well as certain efforts.

Related video:

gypsum stone

Advantages of gypsum coating:

• ease of processing
• light weight,
• variety of textures and rich colors,
• low price.

Such a stone is chosen for finishing plasterboard walls, which cannot be subjected to heavy loads. If you can’t find the right color, there are unpainted products on sale that you can paint at your discretion.

• low impact resistance
• hygroscopicity.

When dirty, such a finish should not be wetted and rubbed hard so as not to damage the surface. Treating the stone with special impregnation or acrylic-based varnish will help to avoid such damage. There is also a gypsum stone with a polymer coating on sale - it is a little more expensive than usual, but it is not at all afraid of moisture.

Fine decorative stone

If you wish, you can make a decorative stone on your own: for this you will need a plastic or silicone mold, a dry gypsum mixture, coloring pigments. Buying all this is not a problem, every hardware store has a large selection of mixtures and shapes. Self-production of finishing material takes more time, but it saves money on repairs.

Source: stroyday.ru

Finishing the hallway with decorative stone:

Distinguish natural decorative stone and, accordingly, artificial. Most often, artificial is used, since it is much cheaper, it is easier to work with it, and in terms of the variety of shapes and colors, such a stone is many times superior to natural. The natural one has a lot of weight and, before proceeding with the finishing, it is necessary to make sure of the strength of the wall on which the plates will be glued.

Tools and materials

For laying decorative stone, you will need the following tools and materials:

1. Hacksaw for cutting stone
2. Spatulas (small 7-9 cm, medium 15-17 cm and medium notched 15-17 cm) for applying glue to the slabs
3. Simple pencil - draw cutting lines for plates
4. Bucket or basin for glue
5. Sandpaper or chisel to fit the boards
6. Kitchen sponges are used when filling joints with putty
7. Tile adhesive (liquid nails)
8. Putty - to cover the seams between stone slabs
9. Paints (usually supplied with decorative stone) for filling joints after puttying
10. Water-based varnish for finishing seams after painting

Finishing technology

Decorative artificial stones are made from colored concrete or based on gypsum. Each builder finds its own advantages and disadvantages in each of these types. For example, for beginners, gypsum-based &mdash stones are best suited, they are easier to work with, they are lighter in themselves and, by the way, cheaper than a concrete decorative stone.

As for the finish, there are a number of nuances. Finishing the hallway should begin with preparing the surface for further work. Differences reaching more than 5 mm must be plastered, and in order for the wall to have good adhesion, it must be carefully primed.

Important! Decorative stone is in no case glued to the wallpaper.

You need to start with the fact that the tile itself should not be immediately glued to the wall. It is advisable to draw on a sheet of paper the location of the stone slabs and lay them out on the floor. So you can choose the elements by size, thickness and understand where it will be necessary to adjust the plates that will be joined to each other.

The stone can be laid both with jointing and without it. The width of the joints also depends on which facing stone is chosen and what result you want to see at the end of the work.

After laying, of course, there will be some defects, chips, cracks and other little things. The easiest way to fix them is with paint, which should be attached to the decorative stone. This paint is fully consistent with the color of the finishing material and perfectly hides all the flaws.

In order to give expressiveness to the stone wall, you can apply a finishing spray on the laid stones. It is desirable that the color be slightly darker than that of the stone itself. You can highlight the contour along the edges with the help of gold or bronze contours, which will give this element of decor even more originality.

If you cover an artificial stone with a matte or acrylic varnish, it will last much longer and will shine beautifully when light hits it. It is important that the decorative stone is in harmony with other finishing materials (wallpaper or paint).

Do not get too carried away with stone trim, as in large quantities this decorative material can make the interior bulky and “pressing”. The use of decorative stone in decoration is quite a modern and very popular solution. This finishing option requires a creative approach and a well-thought-out laying technology in advance.

Source: www.samoremont.com

Decorating the hallway with artificial stone is an original solution for a unique interior

There are many reasons why a decorative stone in the hallway as the main element of wall decoration is exactly what is needed. Let's consider some of them:

1. Stunning design. To begin with, thanks to which this material is generally chosen in the first place - it has a rough, "real" beauty. A person who has dreamed of living in a medieval castle since childhood cannot fail to appreciate this option! And if in the bedroom, finishing the wall under a stone is not a very good solution (evokes thoughts of cold), then the artificial stone in the interior of the hallway looks chic.

Artificial stone, like natural, is ideal for finishing the hallway

• Relatively light weight. If the owner of the corridor is not an extremely poor person, and even a lover of everything natural, then real stone can be preferred, but it has one serious drawback - significant weight, due to which the walls will probably have to be pre-strengthened. Decorating the hallway with decorative stone provides only a thin layer of material, and even that weighs less than a natural one of the same volume.
• No installation hassles. Since the decorative material was originally made for wall decoration, it is already fully adapted to this specificity - there is no need to “drown” it in the surface, it is easily laid out in a thin layer. It is also very easy to install, cement and glue are enough for this. Since the finished surface does not provide for perfect evenness, you will not need a level.
• Finishing the hallway with decorative stone allows you to increase the fire resistance of the room. Artificial stone, like natural stone, does not burn in fire, which distinguishes it from most other finishing materials.
• The stone in the interior of the hallway is also good because it is an almost eternal solution. All other decorative elements usually wear out and need to be replaced much earlier, however, the stone, with due respect and basic care, can last at least a decade and a half, which allows you to forget about repairs for a long time.

How to fit a decorative stone into the interior of the corridor

Like any other finishing material, a decorative stone in the interior of the hallway can turn out to be both a very good solution and a waste of money on finishing, which will only spoil the appearance of the room. It all depends on how the design idea is thought out and logically completed.

Let's start with the color scheme. The entrance hall usually not only has no windows, but is also significantly removed from them, so there is twilight here even during the day, and there is absolutely no need to thicken it even more. It is better to give preference to a light-colored stone - in electric light it will shine beautifully and reflect light.

For finishing the hallway, it is better to give preference to light-colored stone. A completely stone entrance hall in certain cases may seem like overkill. Often, the decoration of the corridor with decorative stone is performed only partially, for example, in the form of inclusions or only along the contour of the doorway.

Such a decision, with the right approach, looks very stylish - one gets the impression that you are in an old building, which is a bit like picturesque ruins. The shade of the stone should not be very different from the rest of the finish, otherwise the individual elements of the decor will not be in harmony with each other at all.

The decoration of the corridor with artificial stone goes well with green plants. A professional designer, with the help of a well-chosen type of plants, is able to completely change the perception of the interior, as a result of which the masonry may seem cute and picturesque, or, conversely, acquire a special wildness. You can try to experiment with this on your own, but only a specialist will be able to easily achieve the planned result.

To focus on a stone-finished wall, it is better to replace centralized lighting with spotlights. Professional repairmen are also advised to abandon centralized lighting when using stone for wall decor.

In this situation, small, evenly spaced light sources of relatively low brightness are much better suited, allowing you to create a uniform illumination of the room. If there are certain accents in the interior - mirrors, paintings, and so on - then it is better to highlight them with additional lighting.

The combination of artificial stone with a classic style

The owners, who are guided by the classical interior design, are afraid of the possibility of combining decorative stone, as a wild material, with sublime and sophisticated classicism. In fact, they are quite well combined with each other, but the classics usually require a significant area of ​​​​the room.

Decorative stone will help emphasize the classic style in the interior. Moreover, in some cases, it is the stone that helps to give the corridor a classic touch. Speaking of the classics, they usually mean a certain fundamentality and solidity, and masonry is ideal for these purposes.

To achieve the goal, it is possible to lay out not only walls, but also the floor with decorative material. At the same time, it is important not to overload the decor with numerous elements, because an excessive variety of details will only spoil the overall impression of the room.

Source: otdelkagid.ru

Finishing with artificial stone doorways and walls of the hallway

Decorating the hallway with decorative stone and wallpaper is a relatively expensive type of cladding, but a respectable appearance of the walls is worth the money invested. The use of artificial stone opens up a wide scope for the manifestation of design imagination.

With a very wide range of colors and textures, and a fairly low weight, it is a versatile material that can be used in apartments and private homes. Stucco decor, tiles, stretch ceilings, and even wallpaper in the hallway - all this looks great with decorative stone, which, in turn, makes it possible to expand the combination of materials for decoration.

Decorating the hallway with decorative stone is quite easy, as there is a large selection of decorative elements, corner and rounded inserts necessary for decorating doorways and niches. Artificial decorative stone is suitable for finishing any surface - concrete, metal structural elements, bricks, wood, etc.

The technology of finishing the hallway with decorative stone

1. First you need to prepare the base. At this stage, we remove the loosely holding old finish - tiles, wallpaper, plaster.
2. If there are irregularities on the wall surface with a difference of more than 5 mm. it must be plastered and primed.
3. Next, we mark the wall and fix lighthouse stones on it. When marking, be sure to take into account the height of the baseboard and cornice.
4. Then we make a control mark in any corner of the hallway, at an arbitrary height, and using a water level or a laser level, transfer it to the remaining corners.
5. From the control mark we measure the distance to the first row of decorative stone. You can also put risks or hammer nails in the corners, and pull the twine over them. Laying decorative stone can be done back to back.
6. And now you can proceed directly to the decoration of the hallway with a decorative stone. The stones are laid in even horizontal rows. On the surface of the wall or the sole of the stone, apply glue with a spatula-comb.
7. The last step is grouting. The glue will set in about 24 hours, and then you should rub the seams using a special grout.

Source: stroyusnulya.ru

Artificial stone in the hallway. Interior Design

Before using this or that material, you first need to study all its features in order to make the right choice. Artificial stone is a mixture of marble placers with various minerals. The natural appearance of the stone, reminiscent of natural material, testifies to its high quality.

This criterion will help in the selection. You also don't need to save when buying. Do not think that natural material is more expensive than artificial stone. Its price may even exceed the requested natural material, as additional resources are spent on its production.

The approximate cost can vary from 500 to 3000 rubles per square meter. Of particular importance is the country of origin. You should also pay attention to the cut of the stone. The surface should be as smooth as possible, without the content of large elements. Otherwise, it threatens the formation of cracks and chips.

Hallway interior with artificial stone

The artificial stone in the hallway looks especially harmonious. However, the design of this room requires some harmony. Contrast and brightness are appropriate only for spacious rooms. But not everyone can boast of a huge hallway. Often contrasting shades visually reduce the space.

This fact should be taken into account when choosing an artificial stone. Natural shades that differ by just a couple of tones from the color of the walls are ideal. Also, do not completely cover the walls in the hallway with decorative stone. It is enough to make a few blocks to place accents. For example, you can decorate a doorway with a stone or lay it out along the floor line. You can also overlay a niche for a cabinet with a stone. The modern design of the hallway with artificial stone suggests asymmetry. It can be laid out in a chaotic manner, without trying to line up the correct figures.

Stages of decorating the hallway with decorative stone

1. Surface preparation for cladding.
2. Complete removal of old finishing materials.
3. Identification and elimination of various defects on the surface (chips, cracks, depressions).
4. Plastering areas with pronounced differences. Coating with putty to a perfectly even state.
5. Primer surface treatment.

Decorating the hallway with artificial stone requires some knowledge and skills. However, even a beginner can do this work.

Laying process

Wall decoration begins with markings. Of course, experienced builders can skip this step. As a rule, they use only the building level. But for a beginner, this is not possible. Therefore, it is better to immediately put markings in the form of lighthouse stones on the wall.

They will indicate the boundaries of the masonry. Laying can be started from any corner of the room. That is where the first mark should be placed. Then, using the level, you need to set the connecting marks. Between them, for accuracy, you can draw twine.

Laying can be done both from the bottom up and from the top down, the main thing is that it starts from the corner. However, most professionals start from the bottom for convenience. In this case, the thickness of the floor plinth and cornice should be taken into account. Artificial stone in the hallway is easier to lay than any other material.

Finishing should be carried out taking into account the thickness of the material. Large stones are covered on the reverse side with an adhesive-based solution. A notched trowel is suitable for application. If the stones are small, then you can use the so-called liquid nails. Stones must be sorted by shade before laying.

Colors in each batch may vary. To facilitate the process, you should lay out the intended pattern on the floor to determine the order of laying each individual element on the wall. Glue is applied to the back surface, and the stone is firmly pressed against the wall. Laying is done with a level so that you can immediately eliminate irregularities.

When the first row is laid butt to joint, you can proceed to laying the subsequent ones in the same sequence. After the entire surface is framed, it must be dried for a day, after which it is necessary to process the seams between the stones with a special solution.

Advantages of decorative stone

If we compare this material with natural stone, then its superiority is simply obvious. Artificial stone has a small weight. This greatly facilitates its transportation and installation. Artificial and natural stone have almost the same strength.

And even in the first, this figure is somewhat higher. Decorative stone has refractory properties. It is not subject to corrosion, the formation of fungi and mold. This is an environmentally friendly material, absolutely safe for health. Its unpretentiousness in care is considered a significant plus.

It can be treated with any detergent. It is much easier to lay due to the correct shape. The process does not require significant effort, it can be compared with laying ordinary ceramic tiles.

Types of artificial stone for hallway design

Depending on the production technology, a decorative stone may contain either colored concrete or gypsum at its base. There are practically no visual differences. However, their weight varies significantly. Concrete stone is much heavier than its gypsum counterpart. It also affects the cost of the material.

The artificial stone, which costs more, will presumably be made of concrete. However, the difference in cost is not so significant. As a rule, it is no more than 200 rubles per square meter. The only drawback of gypsum stone is its low moisture resistance. Some manufacturers cover the material with a waterproof emulsion. This can also be done on your own.

Source: howtoshka.ru

Stone in the interior of the hallway - the benefits of using

• the correct shape and light weight of the decorative stone greatly simplifies all finishing work with it,
• it looks respectable both with ceramic tiles, discreet wallpaper and carpet, as well as with gypsum stucco molding, wooden elements or a stretch ceiling,
• different texture and texture of the finishing stone, its wide range of colors adequately emphasizes the originality of any interior and its unique style,
• artificial stone is not subject to processes such as rotting or corrosion,
• easy to clean, flexible stone can be washed with an ordinary soap solution,
• visually attractive, decorative stone is not only pleasing to the eye, but quite pleasant to the touch,
• convenient and practical in work, it expressively emphasizes the geometry of doorways and forms the ergonomics of space.

On the construction market, the finishing stone is presented in two versions:

1. Natural decorative stone made from many types of rocks: marble, granite, diorite, quartzite, sandstone, etc.
2. Artificial decorative stone. made from gypsum and cement.

A significant difference in price is the only difference between natural and artificial stone. Outwardly, they practically do not differ from each other, which allows you to create a truly inimitable interior in the hallway, both with and without impressive financial investments. It all depends on the capabilities of your wallet and outlook on life, in particular on the decoration of the hallway under the stone.

Artificial or wild stone in the interior of the hallway - which is better?

Slate and malachite, as a stone for wall decoration, were widely used to create chic palace interiors several centuries ago. Walls, floors and fireplaces were faced with solid stone.

Related video: Stone decoration in the interior
Unfortunately, with all its many advantages created by nature itself, one crack is enough for the integral structure of natural stone to be broken. The owners of the hallway and corridor (the most passable place in the house) will have to protect their walls as much as possible so that no one inadvertently damages the marble, granite or basalt finish. Repairing a crack or chip that has appeared will be problematic even for specialists with extensive experience.

Fortunately, with the advent of artificial stone, an innovative material that qualitatively imitates the texture of natural minerals, it has become possible to create easily restored design compositions. Particularly popular in the decoration of hallways was a flexible stone - a composite of the most complex composition, made on the basis of marble chips, natural pigments and environmentally friendly polymers. Plastic and impact-resistant, it easily takes the necessary form of doorways, niches, corners and roundings of arches, and can be used for finishing works of any kind.

Wall decoration with decorative stone in the hallway and corridor - the correct laying of stone on the wall

Surface preparation for stone cladding

• Before starting the main finishing work, it is necessary to clean the surface of old materials.
• After making sure that there are no all sorts of defects on the walls (notches or cracks, which are removed by means of fastening solutions), you can start surface treatment with a layer of plaster, and then putty.
• In order to improve the adhesion of the decorative stone to the base, it is recommended to treat both layers with an acrylic, alkyd or mineral-based primer.

Markup:

• Without a certain experience, it is quite difficult to lay stone on a wall without markings, having only a building level at hand. Therefore, experts recommend making preliminary markings on the surface by setting reference points on the wall - “lighthouse” stones.
• Further, using a laser level or the same level, fix identical marks and connect the “beacons” closest to each other at the level of the main row with twine.

Stone laying:

• To facilitate the process of finishing the hallway interior with stone, you must first sort all the elements according to color shades and lay out an approximate picture of the future finish on the floor.
• Laying is best to start from the corner, or, in extreme cases, from below, accurately observing the thickness of the cornices and skirting boards.
• Large stones are laid end to end with a mixture based on glue, which is applied to the wrong side with a notched trowel. A material with a small thickness is mounted with high-strength glue, for example, "liquid nails".
• It takes about a day to dry the surface treated with decorative stone. After that, you can grout the seams based on a special solution.

Important! Artificial stones, unlike natural ones, lend themselves perfectly to any processing. They can be cut, broken or even sawn to fit stone elements to the desired size.

Most often, not the entire hallway is lined with stone, but one of the walls. This allows you to zone a small space, highlighting its main part. Doorways lined with “chipped” stone look especially impressive. This interior design clearly resembles the entrance to an ancient, dilapidated castle.

Source: moydomik.net

Stages of finishing the hallway with decorative stone

Is it possible to finish the hallway with a decorative stone on your own, so to speak, with your own hands? Such a question can often be heard today from apartment owners who carry out repairs on their own and want to use natural materials to create a cozy atmosphere inside their home.

Of course, decorating the entrance hall of a country house and a city apartment with decorative stone, especially a small one, are two different things, but the purpose of using stone is the same - to create an original design of the room.

If we are talking about the economic side of the ongoing finishing, then we note that decorative stone is an expensive material, it will require certain and considerable financial investments. But this money is worth investing in order to create a truly unsurpassed interior space.

Although today for those who do not have high incomes, but want to change the interior design of an apartment or house using stone, the construction market offers artificial materials made using modern technologies.

Finishing the hallway with artificial stone

Artificial stone is an economical alternative to decorative stone. This finishing material is not only cheaper than natural material, it, in turn, is also much lighter, which simplifies its installation. In addition, the versatility of such a finish can be noted, because the stone can be combined with almost any other finishing materials. It looks great with a stretch ceiling, and with gypsum moldings, and with ceramic tiles, and with a carpet, and so on.

But that's not all. Artificial stone can be used to finish various surfaces both in shape and design, and in the material from which these surfaces are made. First, we note that modern production technologies make it possible to produce artificial finishing stones of various shapes. Finishing the hallway with decorative stone allows you to create unique interiors. That is, they can trim corners, roundings, niches and doorways. Secondly, they can finish surfaces made of concrete, brick, metal, wood, blocks, and so on.

Stages of laying

Primarily the surface to be coated needs to be prepared. To do this, you will have to completely remove the old finishing materials. Then the surface is examined for the presence of defects in the form of cracks, grooves, chips, which are removed using bonding solutions.

In the event that the surface difference is more than five millimeters per square meter of area, then such a wall will have to be plastered. But even after that, it is once again treated with a layer of putty, which brings the surface to the maximum level of evenness. Both plaster and putty layers must be treated with a primer.

Second phase can be called markup. Many experienced craftsmen produce laying without any markings, using only the building level. Beginners are not always able to do this, so it is recommended to make markings on the wall and install beacon stones that will serve as reference points for masonry. To do this, you need to set a label in any corner of the room, from where the process will begin. Then, with the help of a level or a laser level, it is necessary to set the same marks and the nearest, that is, neighboring, connect with twine at the level of the first row.

By the way, according to the technology, stone laying can be started from top to bottom or from bottom to top, it does not matter. Here it is important to start laying from the corner. But most masters prefer to lay from below, it's just convenient. It is important to accurately observe the thickness of skirting boards and cornices.

Next stage- this is the laying of the finishing material itself. Here much will depend on the thickness of the material. If this size is large enough, you will have to use adhesive-based solutions that are applied to the back of the stone with a notched trowel. If the thickness of the stones used is small, then glue like "liquid nails" is also suitable.

Before laying, they must be sorted by color shades, because in each batch the stones may differ. Then lay them out on the floor, in such a way that in what order each element will be laid on the wall. It will just make the process easier.

Then glue is applied to the reverse side, and the stone is pressed against the wall surface. It must be checked by level and, if necessary, immediately corrected. The stones are stacked end to end. In this way, the first row is laid, followed by the subsequent rows in the same sequence.

Artificial finishing materials lend themselves well to processing, that is, they can be cut, broken or filed. Therefore, decorating the hallway with decorative stone does not seem to be a too complicated process. To fit it to the required size, you can safely cut it with a hacksaw for metal or earn extra money with pliers, biting off small parts.

After complete laying of the entire surface to be treated, it is necessary to leave the finish for twenty-four hours to dry. And only after that you can wipe the seams between them. For this, a special solution is used, made on the basis of the grout composition.

This is how you can finish the hallway with stone and create a beautiful, cozy and unique interior. As you can see, laying this material is not so difficult. Here it is very important to correctly approach the implementation of all work and strictly observe all stages or stages of this process.

Source: remontmechty.ru

The luxury of interior decoration with artificial stone (photo)

The stone for the interior based on concrete, porcelain stoneware, conglomerates has won the greatest popularity. This is due to the low cost with excellent quality, aesthetic effect, long service life of interior decoration. Paying attention to the photo of the interior of the apartment with masonry, it becomes clear how diverse the model range and the prospects for using stone are.

Artificial stone for the interior in the interior decoration of the apartment has many advantages:

• light weight,
• ease of installation,
• wide palette of colors,
• an extensive list of imitations of natural analogues,
• durability,
• ease of maintenance.

Depending on the main component, one or another natural monolith is imitated, repeating its color, texture, features. To understand what kind of artificial stone you need, refer to the photo from the Internet, catalogs. On the basis of conglomerates, a smooth stone is produced for the interior, used in interior work. Stones in the interior, such as marble, onyx, malachite, that is, minerals that differ in depth, play of color and its shades, are popular in use.

Wall cladding in the interior of the living room

The beauty and reliability of stone walls were first appreciated by primitive people, but modern interior design offers lighter options. Place accents, give the room a style, set a color, spice it up with eco-friendly notes - artificial stone in the interior can easily cope with this.

Wild stone in the interior is often used. Natural material determines the status, gives luxury, sets the tone for the rest of the content of the house. But its practicality is highly debatable, and often quite often it is expensive.

Using masonry as a wall decoration above the sofa, the issue of additional surface decor is completely removed. The play of colors, textures, the possibility of arranging different types of material, laying out a picture - these possibilities open up scope for a creative approach to decorating a house.

Related video: CORRIDOR FINISHING WITH STONE/PHOTO OF INTERIOR

Kitchen with masonry

The ease of maintenance of artificial materials and the degree of their safety make it possible to use them in the kitchen. This room needs a careful selection of finishing materials, since there is constant contact with water, heating surfaces, food.

Artificial masonry in the interior of the kitchen is much more practical than natural raw materials. Natural facing material, such as shell rock, is able to absorb odors, dirt, and water. Its use in facing leads to the destruction of the structure, loss of appearance, moreover, this stone for the interior cannot be washed with aggressive means.

Artificial stone is produced taking into account consumer requests - it is easy to clean, non-toxic, treated with dirt and water repellents. In addition, this material is refractory, almost as well as natural.

Facing the apron of the working area in the kitchen with stone, sea pebbles, slate or other rock subconsciously gives a person a feeling of inviolability, comfort, constancy of the hearth, the torn edge of the stone pleases the eye. The color of the facing stone is chosen based on the overall design of the room - the contrast or mutual complementation of color palettes in the interior of the kitchen comes only from your desire, the material always plays in favor of the interior.

Decorative stone in the interior of the hallway

Artificial stone for the hallway is a real find. The first room we enter from the street is often unattractive due to its small size. But, if you lay out the walls or floor in the hallway with a stone, then the impression will immediately change for the better.

In addition, such a lining will greatly facilitate the life of the hostess, the ease of care for artificial material is akin to caring for ceramic tiles. But compared to ceramics, an artificial stone floor in an apartment is safer as a floor covering. And how comfortable you can feel in a house where the stonework of the floor in the hallway is heated, with ceramics the effect is not so unique.

If you are planning to use artificial stone in the interior of the hallway, then you should determine the color and styling options. If the hallway is small, then the walls, completely covered with masonry, can turn it into a stone bag. In this case, the light color of the material will help.

Fragmented styling will be more relevant. By approaching the issue of hallway wall design with a creative and at the same time practical approach, several pressing problems can be solved.

Related video: Decorative stone, hallway design, arches, decor, mirror
In the hallway of the apartment, they often lean on the walls, it is here that street shoes stand and outerwear, wet umbrellas and other accessories hang, causing damage to the walls and floor. By laying out the corner of the room with an artificial stone with a torn texture, even if the color is light, you can avoid rubbing the surfaces, the stone is a very resistant material and washes well.

The use of stone slabs in the flooring, in the place of the hallway where the shoes are based, the cleanliness and safety of the rest of the floor surface is observed. Artificial stone in the interior will please with performance that is not inferior to natural counterparts, but much easier to maintain.

Stone interior in the bedroom

The stone for the interior in the bedroom of a city apartment is a rather unexpected reception, but the photos of the bedrooms convince of the appropriateness of such a decor. Whatever the size of the room and its color, it is always possible to bring elements of decor into it and, moreover, the organicity of the interior will not be violated. For a large bedroom, wall cladding above the head of the bed is quite suitable as a highlight of the interior.

Small bedrooms are decorated with a fragmentary installation of stone tiles. They can be placed under the ceiling as a frieze, on the floor as a plinth, or in several places on the walls. A good solution would be to finish a small space near the head of the bed, in places where light hits, to line a window or doorway, to maintain the overall color in the room.

Stone decoration

Decorative stone is used in design not only as a facing material for walls or floors. It is suitable for decorating individual elements of the exterior of an apartment or house. The working island in the kitchen looks luxurious with side walls lined with stone tiles.