How to cut a wide ceiling plinth in the corners. How to cut a ceiling plinth in the corners with and without a miter box. With decorative corners

High-quality repair requires an attentive and accurate attitude to the details. Finishing work with the ceiling, you need to arrange it well - ceiling plinths are used for this. As a rule, the installation of planks does not cause any particular difficulties; you will have to tinker with the corners. Let's take a closer look at how to cut a ceiling plinth in the corners, talk about different methods, and give useful recommendations on the topic.

Ceiling skirting boards of any material can be cut using one of the following methods. They are suitable for everyone except for plastic ones: they are made out using ready-made corners.

For a ceiling plinth, the following tools may be useful, depending on the chosen method of work:

Saw on wood. Useful for working with wooden ceiling plinths.
Canvas for metal. Suitable for other types of skirting boards (foam, plastic, etc.).
Miter box. The tool is a gutter, which has the shape of an inverted P, where lines for cutting are outlined at angles of 45 ° and 90 °.
Electric miter saw. Can be used instead of a miter box, helps to achieve high precision cuts.
Electric jigsaw. It is easy to operate, with the help of it you can qualitatively and correctly cut a corner without burrs.
Stationery or construction knife. Suitable for foam baseboards, it is important that it has an excellent cutting blade, and therefore must be well sharpened.

How to make an even corner: ways

The most difficult thing is to cut the corner so as to get a perfectly even one: the surface of the materials used is not easy to cut, in addition, you need to maintain a good fit, preferably without huge gaps. How to make a corner on a ceiling plinth? You can use several methods: with a miter box, without a miter box, using decorative corners, as well as in an alternative way.

We cut the corners of the ceiling plinth without a miter box

How to cut a ceiling plinth without a miter box? To work, you will need a well-sharpened pencil, a small piece of plinth, a clerical knife (for polystyrene or polyurethane) or a metal saw (for other materials), a ruler.

You need to attach the baseboard to the corner and draw a line with a pencil along the outer edge, then attach it to the other side of the corner and also mark. As a result, a cross will be obtained on the ceiling, the center of which will mark the place where the strips of the ceiling plinth should converge. Position the piece of skirting board where you will be gluing it. Having rested the end against the wall, transfer the desired mark to it. Thus, it is possible to cut the corners of the ceiling plinth without a miter box.

Making corners using a miter box

If the walls and corners in the room are even, you can use a miter box for work. To properly cut the corner, inside the miter box should be placed the part in which the person will make the drink, then insert the saw into the guides. This will hold the piece in place and allow it to be cut at the desired angle. For high-quality cutting of the plinth, it must simultaneously adhere to both surfaces, so it should be pressed against the wall of the miter box. The ceiling plinth is pressed with the side that is closer to you.

With the help of a miter box, you will need to cut a 45 degree angle. First you need to decide how to position the plinth in the miter box. To avoid confusion and cut correctly, place the right plank on the right and the left plank on the left.

Do the work according to the following instructions:

Put together the cut pieces - you got an inner or outer corner.

Attach it to the ceiling and check the geometry. If it is not even enough, it can be slightly corrected with a knife, and in case of minor defects and wide gaps, putty can be used.

How to cut skirting boards using decorative corners

With their help, you can easily and quickly obtain the desired angles in polystyrene or polyurethane skirting boards. Install them on the ceiling, and then glue the strips tightly to them. Cutting them is easy with a utility knife.

How to make corners of a ceiling plinth without tools

Make the necessary marks on the baseboards.
Using a ruler, connect the edge of the skirting board with the mark. If you just cut along the line, the pieces in the corner still won't fit together because the inside will get in the way. You can trim it later by making measurements on the ceiling.
You can lay on the table the piece to be cut, the part that will be located on the ceiling, and cut at an angle of 45 degrees. It needs some adjustment, but less.
Repeat steps 2 and 3 for the second plank, making the outer corner.

Thus, you can make a ceiling plinth without special tools, using improvised means.

Use of fillets

You can not make fillets yourself, but immediately purchase those that were originally prepared for docking. This is how polystyrene foam fillets are produced, which do not need to be adjusted to each other.

The baguette, which will be fixed on the left, must have a right cut, the right baguette - the left one. When creating the inner corner, make sure that the bottom section rises above the top one, for the outer corner everything should be the other way around.

Attach the baguettes to each other, if necessary, make undercuts at the joints of the base. If everything is in order, the skirting boards can be fixed with glue or screwed to the walls with further sealing of the seams.

How to dock skirting boards in the corners

When a certain part of the plinth is glued and a small distance remains to the corner, in order not to be mistaken with the length, it is necessary to leave a margin. To begin with, you can cut off a piece that will be 10-15 cm longer. Then cut the corner in a convenient way, try it on a dry surface, put the bar on the ceiling and select the place to which it needs to be shortened. Cutting is performed at an angle of 90 °.

Next, you need to correctly dock the corners. Made ceiling moldings are attached at an angle of 38-45 °, so the classic 45 ° is not always suitable at the junction. In different cases, the cut edges do not meet and leave gaps. For this reason, after the initial trimming of the corners, it is necessary to carry out a “dry” and most accurate docking of the baguettes directly to the ceiling. You will especially have to tinker with wooden and plastic materials.

After completing the rough docking of the skirting boards, glue or screw the fillets to the walls and ceiling, then, if necessary, use putty and seal the seams at the end.

Important Points

Consider how to properly cut the corners of the ceiling plinth and get an excellent result the first time. Follow a few helpful tips:

Before mounting, both parts must be adjusted to each other. Attach both halves to each other. The wall surface must be dry. Having found defects, you can easily align them with a knife.
It may need a few trims. Don't be discouraged if it takes you a long time to do a few trims, especially if this is your first time doing the job.
Correctly determine the length of the strips in the corners. For an inner corner, the length of the plank should be adjusted exactly from corner to corner; for an outer corner, the measurement is taken from the inner point in the direction of the room.
If the corners as a whole match perfectly, but there are small gaps in the middle, they can be repaired with putty.

How to glue a ceiling plinth

Start in the corners of the room, as they are easier to work with, then move on to other parts of the room. Glue the corners in such a way that, if possible, no gaps are formed or defects, if unavoidable, are minor. For plastic skirting boards, finishing putty is used.

Water or soil is applied to the fastener areas. After the putty mixture has dried, all cracks must be sealed - various sealants are used for coating (professional builders recommend choosing products based on acrylic). In general, one package is required per room. Installation with a sealant is carried out in the same way as when using putty.

How to cut corners on baguettes (ceiling plinth) video

Mark corners with paper
Method of marking with a water container instead of a template
Use of a computer program
How to cut a profile tube at an angle

When installing piping, it is often necessary to reduce the tube below a certain slope.

Accuracy plays an important role in this task. There are several simple ways to cut the tube at an angle.

Incorrect cutting of pipes leads to the impossibility of installing the structure of the originally designed shape. For example, if you intend to rotate the system 45 degrees, the hose must be cut 45 degrees.

To complete the task, you will need marking tools and a Bulgarian (you can replace it with a metal wire).

Marking a corner with a piece of paper

Placement paper is one of the easiest ways to complete a task.

How to make a corner of the ceiling with knitting using a chair and impromptu tools

Requires a square sheet. Precise diagonal fold. The pipe cutting tutorial should be wrapped around the product so that the long side runs parallel to the product.

On the small sides, it is shaped like 45 degrees.

A cut line with a pencil or marker remains on a sheet of paper.

This method is great for long, large pipes with a cut in the center of the product.

Method of marking with a water container instead of a template

This marking method is suitable for small diameter pipes that are intended to be cut at a certain angle close to the edge.

First you need to prepare a deep water tank. Indicates the expected slope of the slope. Now you must carefully load the end of the product into the liquid, tilt it to the mark and pull it out.

As a result of such actions, a clear line of contact with water is displayed on it, it should be emphasized. Pipe cutting is at an angle. This method is best suited for jobs that require multiple markings.

Use of a computer program

To implement this cutting line marking method, you need a computer with special programs. First you need to draw a drawing that shows the cross-sectional dimensions of the product and is also designed as a section.

You need to get a virtual template.

Print it out on your printer. And then you need to understand that the larger the diameter of the pipe, the more sheets you will need to print. Then you need to accurately cut the drawing details on all sides and glue, it is best to apply this office box.

The pattern on the pipes should continue to be used and the label used.

This method of solving the problem is very accurate. You can download all the necessary programs on the Internet, download them and use them for free. There you can also find a sample for cutting the tube at an angle. It remains only to print it and turn it off. To complete the label, the curve simply hangs around the pipe.

How to cut a profile tube at an angle

The profile of the profile tube differs from the profile of the round one. Its manual execution can cause a significant error.

The best way to solve the problem is to create a cutting template from one profile, but with a larger diameter.

Take a small part of the profile tube.

On it, using projutor, mark it as 45 degrees. Now, with the help of a grinder, a piece of the workpiece should be cut along the marked line. The cutting edges must be routed to correct defects. Remains of product remain only in the template for cutting the tube at an angle.

Then you need to mark the cut line of the larger profile. And a tube is already cut through it.

The text describes how to cut the tube at an angle of 45 degrees.

When the tag is already complete, it is recommended to use the Bulgarian language. With it, she will be able to cut smoothly. We can replace it with a metal saw. The other part of the product will weld, but you will need experience with the tool, otherwise there will be irregularity. Also read: How to smoothly split a tube - tools and cutting methods.

Now in construction shops you can find a special tool for cutting pipes. However, it is easier and cheaper to create a template yourself.

How to cut a ceiling plinth

At first glance, it seems that the procedure for installing a baguette is not particularly difficult.

Indeed, this is the case if you properly cut the eaves for the ceiling. This is easy and simple to do with the help of such a device as a miter box. But if the tool is not at hand, do not despair. There are techniques that allow you to perfectly cope with the task and without it. We will teach you how to cut a ceiling plinth without a miter box.

In most houses and apartments, a right angle is decorated with a ceiling plinth, so we will cut the baguette into 2 sectors of 45 degrees.

And let's start with the method, which consists in creating markup on the wall:

Attach the product to the corner at the place of fastening.
Along its edge, we draw a line on the surface, which will act as the base for the attachment level.
We will do the same on the other side, attaching the baguette to the docking wall.
As a result, two lines are formed that intersect at one point.
Transfer it to the baguette, as this point is the top point of the cut.
Next, you should again attach the plinth to the ceiling to draw lines between the edges of the cornice to indicate the cut line.
Attach it to the corner of the room to trim.
To cut the ceiling plinth, use a knife or a hacksaw, depending on the material from which it is made.

In addition, there is a rather interesting way to cut a baguette - draw a miter box on paper.

Draw this device on paper: draw two lines that should be parallel to each other, mark the corners, maintaining their degree, for which you can use a protractor. In this case, trim the plinth in the same way as when using a real miter box.

The product must be parallel to one of the lines. Trim the corner. But this technique may not give an ideal result, since we will cut the product at an angle of 45 degrees, but the corners in our houses are usually crooked, and as a result we get a noticeable gap.

This method of trimming a ceiling plinth consists in creating a special shape.

To do this, you will need 3 planks or pieces of thick plywood. In the sidewalls of the product, make cuts at an angle of 45 degrees using a protractor. Thus, cutting a baguette will turn out without a miter box.

Another simple method lies in the manipulation of paper. Bend the sheet to the desired angle. Then it must be placed on a bar and cut off along the formed line, which must first be drawn.

Such a bar will serve as a kind of template: a ceiling plinth is placed under it in the position in which it will be attached, and the corners are cut off, holding the knife strictly vertically.

A rather expensive way to create the corners of a ceiling plinth without a miter box is to use special additional inserts.

They are divided according to their purpose: for internal and external corners, there are also docking inserts.

If you have to work with non-standard corners, for example, those that have several intersection edges, or rounded ones, you will not need a miter box.

How to cut the corners of the ceiling plinth

After all, the magnitude of the angle is by no means 90 °. In this case, you should take a baguette and use a craft or clerical knife to cut it “by eye” at 45 degrees. Then the part to be joined must already be adjusted to the desired angle, constantly trying on the structure on weight at the installation site. There can be quite a lot of such fittings, so get ready. But if you wish, you can achieve a good result, even if the corners in the room are non-standard.

Thus, the absence of a miter box when installing a ceiling plinth is not a sentence.

On the contrary, this is a great opportunity to learn some new techniques that will help you cut a baguette just as well. And perhaps one of them will appeal to you even more!

Cutting a ceiling plinth: how the professionals do it

If you need to get an angle of 45 degrees, what should you do in this case? For this, there is a protractor known to everyone, even from the school bench, and with it you can measure any angle.

Well, if there is no protractor nearby, then you do not urgently need to search for it, you can do without it.

There are many different tricks or ways to do this, here is the simplest and most effective:

An angle of 45 degrees can be obtained using a regular sheet of paper, you can use a regular notebook or landscape sheet.

In extreme cases, you can get by with a newspaper.

Look closely at the drawing.

In order to get the desired angle, we first make a template out of paper, and with its help we easily measure the desired value.

It remains only to attach a paper blank to the part to be cut and draw a line with a pencil.

As you can see, such a simple trick can easily help out in your work if the necessary tools are not available.

The quality of the ceiling finish greatly affects the appearance of the room. Therefore, they try to make everything perfect, or very close to it. The finishing touch in the design is the ceiling plinth. They give the finish a finished and holistic look. The strips themselves are mounted on flat surfaces simply: with a special white glue, but there are problems with the design of the corners. Without knowing how to make the corner of the ceiling plinth correctly, a lot of material deteriorates. We will tell you about how and with what to cut it in the corners.

What is it made of and what is it called

The very first skirting boards on the ceiling were made of gypsum. They were cast in special molds, then they were installed on the ceiling on the mortar. Such curly ornaments were called fillets. Today you can see them infrequently: they are expensive, and outwardly they are almost no different from cheaper options. And the name is almost lost.

The most popular today are ceiling plinths made of polyurethane or polystyrene. They are inexpensive, look great, are easy to install, and have a wide range of profiles and patterns. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. The exception is wooden houses with an appropriate interior. Wooden products are most often used here - style dictates its own terms.

Part of the assortment in a specialist shop

There is also a similar finish made of plastic. It is mainly installed in bathrooms. But even in damp rooms, you can safely mount polyurethane strips - they are not afraid of dampness.

Cut the ceiling plinth in the corners of any material using one of the methods described below. The only exception is plastic skirting boards: you can make such an angle only using ready-made corners.

What and how to cut

Working with skirting boards of different materials means using different cutting tools. When working with a ceiling plinth made of wood, it is more convenient to work with a wood saw. All the rest, including plastic, foam and other polymers, are better cut with a metal blade. It turns out a more even cut, less burr. Saws are usually used when working with a miter box.

Properly shaped corners look attractive

When working with foam skirting boards without special tools, they are cut with a good clerical knife. Its blade is quite thin and even, the cut is smooth, not jammed. If you work with polyurethane or polystyrene with a saw, do not press hard: you can wrinkle.

In general, in order to get used to the tool and material a little, take some piece and practice on it: cut, saw, cut. So at work there will be less problems.

You can read about the design of the ceiling in this article.

How to get the right angle

Most of the problems when working with ceiling plinths arise when making corners. Since the surface of the products is complex, simply cutting at the right angle will not work: you also need to cut them so that they fit together and preferably without large gaps. In fact, there are several ways to make the corner of the ceiling plinth perfect (or almost).

Using a chair

If the corners and walls in the room are even, you can use a special carpentry tool - a miter box. This is an inverted U-shaped chute with lines for 90° and 45° cuts. The part in which you want to make a wash is laid inside, a saw is inserted into the guides. The part is held in place, cut at the required angle.

This is what the chair looks like. Can be plastic, wood or metal

In the case of skirting boards, everything is not so simple: they must simultaneously adhere to two surfaces, therefore they must be pressed against one or another wall of the miter box. When working with ceiling, they are pressed against the side closest to you.

The sequence of actions when finishing the outer corner you need to make washed down at an angle of 45 degrees. Put the chair in front of you. Try on how the plinth will be located, determining which part of it will be attached to the ceiling. In order not to get confused and cut the ceiling plinth correctly, lay the plank that will be located on the right on the right, the one on the left - on the left.

How to cut a corner on a ceiling plinth: correctly install it in a miter box

With the part that is on the ceiling, press it to the bottom of the miter box. The other side is closer to you and raised. You lean it on the wall of the fixture so that it does not stagger when cutting. That is, the front part of the plinth is turned away from you. Make the cut direction as shown in the photo below. Putting the two cut parts together, you get a protruding - outer or outer corner.

How to make an outer corner of a ceiling plinth using a chair

The sawn off parts are first applied to the place “dry”, without applying glue. If the geometry of the corner turned out to be not so ideal, you can tweak it a little with a knife. Small errors are easier to cover with a special putty.

With the inner corner of the ceiling plinth, the situation is very similar. First, try on which side will be on the ceiling, press this part to the bottom of the miter box, rest the second part on the wall closest to you and make cuts as shown in the photo below.

How to make the inside corner of a ceiling plinth using a miter box

And again, first try on without applying glue, if necessary, slightly adjust. Then apply a thin bead of adhesive to both surfaces that will be attached to the wall or ceiling.

Your version of how to properly use the miter box is shown in the video.

How to make a corner of a ceiling plinth without a miter box

Few people in apartments or houses have exactly 90 ° angles. Small deviations are easily corrected after fitting. But not always. Then you have to mark everything "in place" - under the ceiling.

You will need a finely defined pencil (hard - it is not so visible on the ceiling, but leaves fairly clear marks close up), a small piece of plinth, a ruler and a good stationery knife if you work with polyurethane (polystyrene) baguettes or a metal saw to work with the rest of the materials.

Apply the plinth to the corner, draw along the outer edge with a pencil. Apply to the other side of the corner, also note. You have a cross on the ceiling, the center of which marks the place where the strips of the ceiling plinth should meet (see photo). Having installed a segment of the plinth in the corner, which will be glued there and resting it with its end against the wall, transfer the mark to it.

How to make corners on ceiling plinths without using special tools

Now take a ruler and connect the edge of the plinth with the marked mark. If you just put the plinth on the table and cut along the line, the two parts in the corner will still not add up: the inside will interfere. It can be trimmed later, trying on the ceiling. The second way is to set the piece to be cut on the table with the piece that will be on the ceiling. And cut along the line, but holding the knife at an angle of about 45 °. You will still need to correct, but much less (and less likely to make a mistake).

Repeat the same operation with the second bar. Attach to the desired wall, rest the butt against the adjoining wall, mark the place where the cross is drawn, draw a line and then cut it off. Correction is carried out "dry" without applying glue.

You repeat exactly the same actions for the outer (protruding) corner. Now you know another way to make a corner of a ceiling plinth, and without a string or other special devices.

How to install sliding interior doors can be found here.

With decorative corners

There is another, the easiest way. For skirting boards made of polyurethane or polystyrene, use ready-made, factory-made decorative corners. They are installed in a corner, the strips are glued closely to them. Cutting them if necessary is very simple: a few millimeters with an ordinary clerical knife.

Examples of finished corners for fillets

How to join in corners

If the installation of the first corner is completed, we can assume that you have already learned to do almost everything. “Almost” because you still need to learn how to connect the corners and cut the planks to length. When some part is already glued and there is a small distance to the corner, how can one not make a mistake with the length? The answer is simple: leave a margin.

At first, you can cut off a piece 10-15 cm longer: there will be an opportunity to redo it several times if something does not work out right away. Then you make a corner in the way described above, try it on dry, adjust everything so that the result suits you. Only after that you can put the already cut bar into the corner and mark the place to which it can be shortened. You need to cut exactly at 90 °. It is not necessary to use a stool. Just try to put the knife (hacksaw) perpendicular to the surface.

Today it is impossible to imagine the interior of a residential building or apartment without ceiling plinths. The plinth covers irregularities in the false ceiling or wallpaper, gaps and imperfections in the walls, and gives the interior completeness. But how to make the skirting board fit perfectly in the most important place - in the corner? There are several ways.

Miter box use

Correctly cut the plinth for mounting in the corner will help the miter box - a special device, which is a tray for cutting boards, plastic, etc. at different angles. The miter box can be bought at the store or made by yourself. Usually a saw is attached to the miter box sold in stores, but you can use your own tool.

The miter box has a recess for a board or plinth to be cut off and saw slots at an angle of 45 and 90 degrees. You will need to cut the baseboard at a 45 degree angle.

To cut a skirting board with this tool, follow these steps:

We apply the plinth to the future attachment point.
Mark where we will cut.
We put the plinth in the chute of the miter box so that the lower part is pressed against the surface of the fixture, and the part that will be smeared with glue “looks” up.
Cut off the section by inserting the saw into one of the 45-degree holes.
We correct the cuts with a knife or the same saw (remove irregularities).

After that, the plinth can be glued into place.

How to make a miter box yourself?

If desired, the miter box can be made at home. It can be made from wood or iron. The dimensions of the workpiece do not play a special role, but the wider it is, the more accurate your cuts will be. However, if the width is greater than the length of the hacksaw with which you will cut the baseboards or boards, then sawing will be extremely inconvenient, so you do not need to take a workpiece that is too wide.

First, a transverse straight line is marked in the center of the workpiece. Then, at a distance of 1/2 the width of the workpiece from the intersection of the straight line with the edges of the workpiece, marks are made. Then these marks are connected crosswise, as shown in the figure.

Next, the process of marking the side walls of the miter box begins. Attach them to the already marked base and make marks, focusing on the marking of the base. Then draw straight lines from these marks across the entire wall.

After that, the installation process of the miter box begins. The walls must be attached to the base with self-tapping screws if the fixture is made of wood or chipboard or corners with bolts if it is made of steel. Only after installation in the miter box, cut through the slots for the saw.

After making slits, the miter box is ready. If you have a large volume of work or want to do repairs regularly (on a professional basis), this simple device can speed up the process of cutting skirting boards by 5-10 times.

How to cut a plinth without a miter box?

The easiest way is to draw a future cut line on paper (cardboard, wallpaper), and then, attaching a plinth blank to it, cut it off.

To do this, you must first attach the baseboard blank to the paper and draw two parallel lines that will indicate the sides of the baseboard. Then, using a protractor, you will have to measure 45 degrees and draw a line for the future cut. Then the drawing is used in the same way as the miter box: a workpiece is placed on it and the excess is sawn off along the line.

The disadvantage of this method is that the saw will have to be kept on weight, focusing on the drawing, and not inserted into a pre-prepared slot.

If the angle is not right

Unfortunately, in some cases, the angle between the walls in the room is not straight, but sharp, or, conversely, obtuse. This is due to structural defects that arose through the fault of non-professional builders, the architect's idea, or the result of subsidence of the soil some time after the construction of the building. This is especially common in village houses and cottages.

No miter box or a drawing that replaces it will help in this case, and you will have to do the markup in place.

Attach the workpiece to one of the walls so that it rests against the other wall with its end.
Draw a line on the ceiling along the workpiece.
Perform the same operation on the other wall.
At the intersection of the two lines, mark the workpiece itself.
Draw a line from the mark to the corner of the workpiece and cut along it.
Do the same with the blank, which you will attach to the other wall.
Glue both blanks; they fit tightly.

External corners

It happens that the room has not only internal, but also external corners, which also need to be pasted over with a plinth (see photo). How to do it? There are also several ways here. The easiest way, as in the case of internal corners, is to cut them with a miter box. The outer joints must be cut so that the side that will be glued to the ceiling is on the surface of the miter box, and the side pressed against the wall is facing the wall of the fixture.

As in the case of internal corners, you can also use the markup "in place", that is, draw lines on the ceiling. Here the technology exactly repeats the one used for internal corners.

You can use wall markings by attaching a blank and drawing a line along its bottom edge (see photo).

If the outer corner is too rounded, you can finish the joint with a knife.

To the point where they converge, a line is drawn straight along the future part of the connection. From the point on the ceiling to the second. The resulting markup will be the line along which you need to saw off or cut off the connecting parts. Using these techniques, you can no longer wonder how to cut the corners of the ceiling plinth.

What tools can be used?

The expediency of using certain tools is related to the materials from which the plinth will be made.

Tab. 1. Varieties of materials and features of their use.

Variety of material	Material properties, requirements	Tool
Polyvinyl chloride (PVC)	PVC skirting boards are distinguished by the fact that they are easily damaged when pressed and no longer restore their former appearance, as they are devoid of elasticity. Therefore, such skirting boards cannot be pressed when cutting.	Cut with a construction knife or a hacksaw for metal. A blade or a sharpened kitchen knife is also suitable.
Styrofoam	The foam plinth is also not very durable, but it is better than PVC analogues. Crumbles easily.	You can use the same tools as for PVC
Wood	Stronger and more aesthetically pleasing than their polymer counterparts, but expensive.	Wood is best cut with a hacksaw, you can use metal, although this way you risk clogging the teeth of the blade with sawdust. A fine-toothed wood saw works best.

Using factory corners - an alternative to cutting and sawing

Instead of cutting skirting boards, you can use ready-made corners, which are sold in the same hardware stores. In this case, the main plinth can simply be measured and cut in the usual way, at a right angle, and then attached end-to-end with the corner element.

The disadvantage of corner elements is that they are actually and visually larger than the baseboard, which will make the corner noticeable. This can ruin the look of the room. It is also inconvenient to use the corners where the walls do not meet strictly at an angle of ninety degrees. But most of the time they look great.

Conclusion

Thus, cutting corners when gluing skirting boards is one of the most complex and responsible procedures for which it is advisable to use a special device - a miter box - which allows you to cut the skirting board at an angle of 45 degrees. If the angle between the walls is not straight, you have to use manual markings. Cutting tools depend on the material from which the baseboard is made.

Video - How to properly dock skirting boards

What is it made of and what is it called

The most popular today are ceiling plinths made of polyurethane or polystyrene. They are inexpensive, look great, are easy to install, and have a wide range of profiles and patterns. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. Exception - Wooden products are most often used here - style dictates its own terms.

There is also a similar finish made of plastic. It is mainly installed in bathrooms. But even in damp rooms, you can safely mount polyurethane strips - they are not afraid of dampness.

What and how to cut

In general, in order to get used to the tool and material a little, take some piece and practice on it: cut, saw, cut. So at work there will be less problems.

How to get the right angle

Using a chair

How to make an outer corner of a ceiling plinth using a chair

And again, first try on without applying glue, if necessary, slightly adjust. Then apply a thin bead of adhesive to both surfaces that will be attached to the wall or ceiling.

Your version of how to properly use the miter box is shown in the video.

How to make a corner of a ceiling plinth without a miter box

Few people in apartments or houses have exactly 90 ° angles. Small deviations are easily corrected after fitting. But not always. Then you have to mark everything "in place" - under the ceiling.

How to make corners on ceiling plinths without using special tools

You repeat exactly the same actions for the outer (protruding) corner. Now you know another way to make a corner of a ceiling plinth, and without a string or other special devices.

With decorative corners

How to join in corners

It is known that in order to obtain an ideal articulation of two corner blanks of a ceiling plinth, it is necessary to correctly draw up a cut line for each of them. In this article, you can learn how to properly cut a ceiling plinth, as well as get acquainted with the tools that are needed for this.

Skirting board cutting methods

There are the following ways of cutting the ceiling plinth:

Cutting using a miter box.
Cutting using a special stencil.
Cutting by applying a pencil markup.

A miter box is a special device with which you can form an arbitrary angle from those that are in its set of cuts.

When working with this device, the plinth must be inserted into it in exactly the same way as it will be located on the ceiling. Holding the upper part of the workpiece, its lower edge must be pressed against the wall of the fixture and cut according to the shape you have chosen.

To prepare plastic baseboards, you can use a regular hacksaw. But when applying it, you should not make significant efforts, as this can lead to the formation of chips.

Preparation of joints with an arbitrary angle

Since the walls in the rooms do not always adjoin one another at 90 degrees, it is worth familiarizing yourself with the technique of preparing an arbitrary cut angle.

This technique is usually implemented in the following two ways:

Using a cardboard stencil, the halves of which are obtained by cutting it at the angle you need. Using such a stencil as a template, according to which cuts of plinth blanks are formed, you can get the perfect corner joint.
The second method involves preparing the cutting site using pencil markings and is as follows:

Pay special attention to the fact that with this method of marking, maximum accuracy must be observed. The quality of the resulting joint will completely depend on how accurately you carry out this procedure (and, of course, on how accurately you cut the cut on the workpieces).

In the same sequence, the cutting lines for the outer corner are prepared. But at the same time, there is no need to transfer the point of intersection of the marking lines to the plinth, since in this situation it is the upper point of junction of the corner parts of the blanks. In this case, you have to move the junction point to the wall.

The final stage of work

Upon completion of operations for the design of joints, a control check of the fit of the workpieces on the cut should be carried out.

In the event that there are gaps in the joint, you will have to fine-tune it by slightly trimming the baseboard or processing the cuts with sandpaper.

And in conclusion, we will acquaint you with how to properly cut the ceiling plinth more accurately. Fitting the joining line of adjacent sections of the plinth should be done even before you start marking and trimming its length. With the reverse order of operations (first - the length, and then - the angle) and if you fail to design the joint, you risk completely ruining the workpiece.

Video

For more information on the technique of cutting a ceiling plinth for corners, see the following video:

Categories

Popular