How to make the edges of a plastic bottle smooth and not sharp. How to straighten a plastic bottle Ladybug from plastic bottles

Helpful Hints

Things made with your own hands are always more valuable and more expensive. We bring to your attention a master class, thanks to which you can learn how to make not only beautiful, but also useful things from plastic bottles.

See also: palm tree from plastic bottles

Bird dispenser from a plastic bottle

You will need:

1 liter plastic bottle.
2 wooden spoons.
Screw.
Rope.

1. Draw a hole with a radius of 1 cm at a distance of 10 cm from the bottom.

2. Rotate the bottle 90 degrees and draw another hole with a radius of 2 cm, opposite the first one.

3. The same process must be repeated at a distance of 5 cm from the bottom.

4. Then carefully cut out all the drawn holes with a knife.

5. Now you can insert spoons.

6. To hang the bottle, you need to fasten a screw or screw to the bottle cap and hang it on a rope.

7. Finally, you can fill your tank with bird food.

Do-it-yourself seedling dispenser from a plastic bottle

This is a real garden that moisturizes itself, and you need to make a minimum of effort. In addition, crafts of such pots diversify children and fresh parsley, sage, rosemary and thyme are always needed in the kitchen.

You will need:

Marker.
Sturdy 1 liter plastic bottles with caps.
Scissors.
Label remover (e.g. vegetable oil).
The soil.
Saplings (they can be purchased in the vegetable departments of supermarkets).

1. Mark a line 12 cm from the bottom of the bottle.

2. First, pierce a hole on the marked line with a knife, and then cut the bottle in a circle with scissors.

3. Remove labels with vegetable oil.

4. Insert the top of the bottle with the cap into the bottom base.

5. Fill the top with soil.

6. Fix the seedling by gently pressing it down with soil.

7. Add water to the bottom of the bottle so that the water covers the cap.

8. After that, some water will be absorbed by the soil and you need to add water, following the instructions for a particular plant.

Craft a pencil case from a plastic bottle

Unnecessary plastic bottles can fit into the right and convenient pencil case. The proposed thing can be improved, it all depends on your imagination.

You will need:

Empty, washed and dried plastic bottles (in this case 6 pieces).
Scissors.
Old newspapers.
Paint in bolognese.
Paperclips.
Glue (it is necessary that it glues the plastic well, but does not corrode it).

1. Lay the bottle on its side and carefully insert the knife blade at the base. Cut along the bottom edge.

2. Repeat the procedure with the rest of the bottles.

3. Place all received products on the old newspaper with the bottom up.

4. Spray the paint on the outside of the products in several layers.

5. After the bottles are dry, it's time to line the edges of the cut with felt. The felt strips should be slightly longer than the circumference of the bottle. Glue the material evenly and carefully to each section of the bottle.

6. Wait 15-20 minutes for the glue to dry. It is better not to touch the extra, remaining felt for now.

7. Secure the felt with paper clips for a better bond. Wait another hour and then cut off the rest.

8. Decide where exactly the whole structure will stand, and glue all the bottles together from the side of the felt along the edges with glue. For a good strength of the entire pencil case, do not spare glue.

9. The glue must dry completely. You can fill your pencil case. Everything is ready!

Crafts from caps from plastic bottles for the garden

Sealed bag

1. Trim the thread on the neck of the bottle.

2. Insert the plastic bag through the neck and screw on the lid.

This seals the bag, which contributes to the long-term storage of products.

Original curtains from covers

These original curtains as interior doors can decorate a house, cottage or apartment.

Just connect the caps from plastic bottles together with fishing line or thread. At the same time, the curtain pattern can be limited only by your imagination.

DIY paintings from covers

Plastic bottle caps can even work for fine art.

Try to make such a picture, because even children can do it.

You will need:

Canvas (any size desired).
Plastic bottle caps.
Paint (acrylic) and brush.
Pencil.
Ruler.
Glue (not fast drying).
Assortment of jewelry, balls, mosaics or buttons.

1. Using a pencil and ruler, mark sections on the canvas.

2. Glue one large plastic cover in the center of each section. Next, you can glue the covers of different sizes and shapes first.

3. Paint the entire canvas with black paint and let dry.

4. Glue an assortment of jewelry in the center of each lid and let dry.

5. Now the sections can be colored as you like.

How to make plastic bottle toys

DIY snake toys

Make funny snakes out of foam by creating a simple device at home!

You will need:

Scissors.
Plastic water bottles.
Old towels.
Rubber strip.
Small bowl.
Dishwashing liquid.

1. Cut off the bottom of the plastic bottle.

2. Secure the towel to the bottom of the bottle with a rubber band.

3. Dip the bottle, towel-side down, into the bowl of soapy water. After that, you can create snakes from tiny bubbles.

Important! Care must be taken to prevent soapy liquid from entering the mouth and eyes.

DIY crocodile toy

You will need:

Two half liter plastic bottles.
Bottle caps.
Scissors.
Glue.
Thin paper.
Tassel.
Waxed paper.
Eyes (for example, buttons can be used).

1. Using a knife and scissors, cut the bottles in half, then cut one piece so that the height remains 7 cm.

2. Trim the edges of the bottles so that the crocodile is bent.

3. Glue the legs-lids to the crocodile evenly.

4. Make thick balls of paper and attach them like crocodile eyes.

5. Cover the entire body with thin green paper.

6. Cut out waxed paper and glue on paws, eyes and teeth. Paint your teeth white and your nostrils and eyes black.

Instructions: a vase from a plastic bottle

1. For convenience, cut the bottle on the upper contour.

2. Measure and evenly cut strips around the bottle. It is more convenient to do this by cutting wider segments in half.

3. Gently press and fold all strips outwards.

4. Press down on the bottle, placing it upside down on a flat surface. This will help even out the edges.

5. Fold the end of each strip under the next two. Do this so that the tip of each strip is in the place indicated in the photo.

Balls and stones can be added to create a beautiful play of light in the sun. Since the vase will be very light, the weight can contribute to proper balancing.

A warning! Such a vase will be subject to large temperature changes. Therefore, do not leave it near heating units in order to prevent thin strips from spreading.

Large lamp in the garden from a plastic bottle

The bottle is used as a light source. Such an invention is capable of making a lamp with a large illuminated space from a small lantern.

Alternatively, you can use a bleach solution in a bottle for the best light diffusion.

Universal spoon from a plastic bottle

Here is such a simple, but at the same time, sometimes very necessary spoon (for example, at a picnic) can be cut out of an empty plastic bottle.

Making food containers from plastic bottles

The idea is to use two plastic bottles to make a storage container for food like beans, rice, noodles and sugar.

Just cut out bottles of different sizes: the long one will be the base, and the short one will be the lid. Choose a size so that the lid closes easily and at the same time tightly.

Watering from plastic bottles

If you have a large garden but don't have time to water and don't want to invest in expensive newfangled structures, here's a simple sprinkler idea.

What only use plastic bottles do not find in the hands of craftsmen! They make complex decorations for the garden - vases, palm trees, arbors. This material is also used to create simple scoops, as well as in jewelry. But one of the most interesting trends is the use of plastic bottles as roofing material. It is quite possible to build such a roof with your own hands.

Do-it-yourself roof construction from plastic bottles

Advantages of plastic bottles as roofing

The roof of their bottle plastic has a whole host of advantages.

It is worth noting the advantages that distinguish plastic bottles:

Low cost. It is possible to purchase empty plastic bottles from manufacturers, but an even cheaper option would be to use already used containers. Such materials can be asked to be left for you, for example, in a cafe or with friends. This will help reduce the cost of building materials.
Durability. Plastic bottles are able to withstand heavy loads and mechanical shocks.
Possibility of multiple use.
Ease of use during construction work.
Durability. It should be noted that, unlike other building materials, plastic bottles have a longer service life - about three hundred years. This is many times higher than the characteristics of existing analogues.

Instructions for building a roof from plastic bottles

There are several options for creating a roof structure using plastic bottles. It is only worth noting that it is better for work if all the material is of the same size..

Material preparation

Using a knife, it is necessary to cut off the bottom and necks from the bottles in order to get an element that looks like a tube.
The resulting part should be cut. You need to do this so that you end up with sheets that have a size of about 25x30 centimeters.

Method one

The resulting sheets must be straightened. This can be done using hot water, or you can put all the sheets in a pile, placing them under a press or under a carpet. Another option would be to use an iron.

It is necessary to use a not very hot iron, and it is better to iron plastic sheets through paper.

When all the sheets are straightened, you can proceed to the process of fastening them together. To do this, you can use glue, which is based on dichloroethane.
How to straighten a plastic bottle with your own hands

Such a fastener will allow you to create a high-quality connection, and working with it is quite simple. The glue will melt the plastic pieces, allowing them to be held together.
The connection of the prepared elements can also be provided with a hot iron, melting the blanks through thick paper.
After you have prepared several sheets of the desired size, proceed to their fastening with a stapler. Do this on a wooden frame, which must be prepared in advance.
This wooden frame will be the basis of the roof. To create such a design, you can use plastic bottles that have different shades. Putting together a colored mosaic of pieces will make the roof more interesting.

Method two

This option involves the use of plastic tubes cut in half. The product does not need to be straightened. You will need twisted elements that need to be folded in half. In this case, if the semicircle is unwound back, we get an even designation of the bend.
After the work done, you should get an element that looks like two slides.
Next, you need to do the same with the second sheet. It is placed on top of the initial element. This must be done in such a way that the final design resembles three slides.
After adding the third sheet in the same way, you should get one more slide, that is, four. Thus, the entire roof structure is filled.
The fastening of the elements is carried out along the edge. The work is carried out with a stapler.
This method of making a roof from plastic bottles resembles a tile coating in appearance.
Installation is carried out in strips. After installing one, proceed to another. The second strip must be attached to the first overlap, placing it a little higher.
Finished strips of plastic construction are fixed on the roof, starting from the bottom and moving up - from the edge of the eaves to the ridge.
At the same time, the roof ridge of plastic bottles is made in the same way, preparing the elements and fixing them at the top.
Laying the top layer of plastic products is carried out in different ways, in contrast to the slope of the roof:

with a sloping roof, the last layer of homemade tiles is fastened in such a way that the upper parts go onto the wall, protecting the junction of the wall and roof;
in case the roof has two or more slopes, then it will be necessary to close the joints of the slopes with the help of an additional row of parts, fixing them at both ends of the different planes of the gazebo roof.

Roofing is best done with a slope to allow water to run off the plastic cover.
When straightening the elements under hot water, it is necessary to immerse the product in liquid for three to five minutes, and then put it under the press for one or two days.
Installation work is carried out using a construction stapler. But a better way would be to use an awl and a nylon or cordon thread. This fastening option will provide a longer roof life, adding additional resistance to wind loads.
It is convenient to lay the plastic coating on plywood sheets, fixing the structure with self-tapping screws.
To prevent the formation of leaks in plastic roofing material, rubber gaskets must be used.

Recently, translucent plastic roofing has become increasingly popular. Moreover, such a roof is arranged not only in office buildings or public centers, but also in private homes.

As a rule, plastic roofing is made of polycarbonate sheets or polyvinyl chloride roofing. Let's look at these two materials in more detail.

Roofing PVC

In cross section, the PVC sheet has a trapezoidal or wavy profile. This form was taken for a reason, thanks to this it is possible to give additional rigidity to the PVC sheet. A roof made of this material perfectly protects against snow, rain or wind, but at the same time perfectly transmits sunlight.

The plastic roof is used for various sheds on personal plots, as well as for covering terraces or verandas in private houses. The use of PVC sheet in private construction is absolutely harmless to humans, since the product is produced by extrusion. Due to this, the material does not contain harmful plasticizing additives.

Of the advantages of a plastic roof, it is worth listing:

In addition to all these advantages, it is worth noting that plastic roofing can be used even at temperatures of 60-85 degrees. During combustion, the material does not form droplets during melting.

In addition, plastic sheets are very easy to process and install, since PVC sheet is easy to cut, saw and mill.

She just put a plastic bottle on the iron...

Also, PVC sheets can be bent in a cold or hot state, glued or welded.

However, you should be aware that PVC sheet cannot be used on roofs with a slope of less than 6%. The overlap of sheets during installation must be at least 200 mm. The distance from the edges of the sheets to the mounting holes should be taken equal to 4 cm or more. To cut the material, a hacksaw for metal or a circular electric saw with a carborundum disc is used.

corrugated plastic roof

As a rule, a plastic roof is mounted at a temperature of at least 5 degrees. Sheets are fastened using spacers in places where self-tapping screws are screwed in. Moreover, the holes cannot be punched, they must be made using drills. When laying the boards, it is important that the side of the PVC sheet with the protective coating is on top.

Polycarbonate sheets

Plastic roofing with the use of polycarbonate sheets is becoming so popular that over time even glass roofing will be replaced. Such popularity of sheet polycarbonate is associated with their reasonable price, ergonomics, durability and excellent light transmission.

The scope of roofing polycarbonate is quite wide: it is the urban construction of various sheds, covered parking lots, parking lots, public transport stops, and the private construction of various sheds, canopies. This material is especially popular in places where the use of anti-vandal coatings is required.

Such a plastic roof makes it possible to achieve high architectural expressiveness of urban construction projects. Polycarbonate roofs are especially popular in the construction of greenhouses, greenhouses, greenhouses, galleries and winter gardens. Here, such qualities of plastic as flexibility and translucency are simply irreplaceable.

There are also finished products made of polycarbonate, which you just need to assemble. Such kiosks, sheds or roofs are very quickly mounted and dismantled if necessary.

Alternative plastic roof

It may sound paradoxical, but the plastic for the roof is literally lying around under our feet. And these are ordinary used plastic bottles. It turns out that they make a wonderful plastic roof. Thus, we solve two problems at once: we save our money and we solve the problem of recycling plastic bottles.

plastic bottle top

You will need plastic bottles of approximately the same size. They need to cut off the neck and bottom so that a tube is obtained.
Then you need to cut it along.
Thus, we have a piece of rectangular-shaped plastic approximately 30x25 cm in size.

There are several ways to make a roof from used plastic bottles:

First you need to straighten the resulting piece of twisted plastic. To do this, you can use hot water, a press or a not very hot iron (ironing through a sheet of paper).
After straightening the sheets, we glue them with dichloroethylene or a hot iron.
So we prepare several large sheets of fused plastic, which are then fixed to the roof with a stapler on a pre-prepared wooden frame.
If you take pieces of multi-colored plastic, you can get a mosaic roof.

In the second case, the roof of plastic bottles is made without straightening the sheets. They just need to be bent in half in the opposite direction of twisting. Something like two hills twisted upwards is formed. We prepare the sheets in this way and fasten them with a stapler on one twisted side, making an overlap.

We have a long wavy strip, which we fix along the bottom of the roof. We fasten each subsequent strip with a stapler overlapping over the previous strip. Thus, we sew the entire roof from the bottom up. The resulting roof vaguely resembles a tiled roof.

Forum site Gas handle| Home | Registration

pages | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | »»

Plastic bottles - in business

or dunk sharply? or water it!

Forums » Workshop | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | »»

Many items that we consider unnecessary in everyday life can be useful for creativity. The most common plastic vessels will be a suitable basis for bright products. With simple manipulations, you can create toys, pictures, garden figures for landscape design, flower pots and crafts in the shape of animals.

Crafts from plastic bottles for the garden

You can easily decorate your backyard with plastic bottle crafts for the garden. Designing such figures is not difficult, you just need to use your imagination. With them, the site will acquire originality and brightness. You can connect children to work: they will like to create beautiful, interesting figures from simple materials that are stored in every home.

How to make a palm tree

To form a craft from plastic bottles with your own hands in the form of a palm tree, you will need:

brown containers - 10-15 pcs.;
awl or drill;
green plastic vessels - 3-4 pcs.;
sharp scissors;
a metal or willow rod.

Bottles with a capacity of one and a half liters must be washed, stickers and cap rings removed from them.
Form the leaves of the tree from a green container. To make them lush and long, cut the bottom as low as possible.
Cut the bottle lengthwise into 3 identical parts to the neck. On the sides of each resulting sheet, make a fringe. Form cuts closer to each other, then the crown of the palm tree will be more beautiful.
Leave 1-2 cm in the center of the leaf. To make the vegetation look realistic, place their central part under the candle, but not too close so that the green part does not smoke.
Proceed to the creation of the trunk. It must be formed from a brown container. Cut the bottom at a height of 10-15 cm.
Cut each part along the edge with cloves, bend them to the outside.
In the central part of the blanks for the barrel, create holes with a drill or a red-hot awl.
Start assembling the palm tree. To do this, stick a metal or wood rod into the ground. On it, assemble the barrel structure from brown parts, inserting them inside each other.
The crown of the tree is fixed as follows:
leave the lid in the last green blank;
make a hole in it;
put the received part on top, it will press the lower sheet plates.

DIY plastic bottle flowers

You can make products from plastic bottles shaped like flowers using the following materials:

plastic containers;
marker
scissors;
lighters.

How to make crafts from plastic bottles with your own hands:

Using a marker, draw outlines of flowers on the surface of the bottles. To make them voluminous, do it from the bottom. Cut out the flower blanks along the lines.
Bend each petal to one side. Shape with a lighter.
Connect the blanks by placing them inside each other. For fastening, you can use wire, glue or heat plastic.
Decorate the core with beads or a finished plastic flower.
Using this idea, you can create different flowers: lilies of the valley, daisies, times. Make a whole flower bed in the country yard by enclosing artificial plants with a car tire.

Swan for giving

Crafts from plastic bottles for the playground are suitable for installation in your garden. Make a beautiful swan using materials:

plastic bottle (five liter);
wire-based hose;
white half-liter bottles;
wire;
paint;
scissors;
a candle;
marker.

Instructions on how to create a craft:

Take a five-liter container and mark the shape of the bird's body on it with a marker. The contours should look like a boat, while the neck of the base should not be cut off. Cut the plastic along the line.
The neck of a swan is formed if a hose is placed in the neck.
Form bird feathers from milk vessels. Remove the necks and bottoms, and cut the remaining material into pieces to get plumage, give each part a fringe, melt with a candle. Take 2 feathers by tying them together with wire. Attach to the body using glue.
Leave the rest of the small bottles to form the neck. Cut off the bottom of them, start stringing on the hose. Create the bird's head using the top of the white vessel. Create holes on both sides in the container and hose. Connect 2 parts with wire, screw the lid.
Caps from bath products are suitable for the beak. Cut in half and glue to the lid. Color the beak and draw the eyes.

DIY Christmas decorations from plastic bottles

You can prepare Christmas decorations from the following set:

glue "Moment Crystal";
liter plastic bottle;
tapes;
scissors;
plastic beads on a string.

Instruction:

Divide the bottle into 4 rings 5 mm wide. Coat each with glue, let dry a little.
Place segments from the beads on the adhesive surface so that there are gaps for assembly at the top and bottom of the ring.
After drying, connect the rings by inserting one into the other.
Tie a thin ribbon to the top of the resulting ball to create a loop. Hide an ugly knot by decorating with a bow from a thicker ribbon.

Crafts from plastic bottles for kindergarten

Kids in kindergarten are given a lot of room for creativity. Products are unusual and bright, and the process of joint work will captivate children and adults. However, sometimes parents have to puzzle over what crafts to do with a child in kindergarten. A simple solution would be plastic bottles. This material is easy to find and use because it freely takes on any shape.

butterflies

To make a butterfly, a child will need:

marker;
plastic bottle;
paints;
scissors.

Step-by-step instructions for creating crafts from plastic bottles:

Find a flat part of the container, cut out the cylinder. Cut the resulting shape in half.
Draw a butterfly on the resulting part, cut it out along the contour.
To give naturalness, make bends on the wings.
You can color and decorate the butterfly as you wish.
They can decorate an apartment or street decor elements, for example, a weather vane, a railing, a flower bed.

Ladybug from plastic bottles

Required materials:

small plastic containers;
chestnuts or beads;
glue;
scissors;
marker;
acrylic paints;
wire.

How to make crafts from plastic bottles with your own hands:

First, make the body of the ladybug. It will turn out if you cut off the bottom of the bottle and take it as a basis.
To give it a similar look, paint the part with paint and draw black circles with a marker.
Glue a chestnut or a large bead to the body to make a head. Draw eyes on it.
Make the antennae out of wire by gluing or sticking them into the head blank.
According to this scheme, you can make other insects, for example, a bee.

DIY plastic vase

Materials that will help you design an original vase:

a vessel of the required volume;
scissors;
stationery knife;
glue;
magazine.

How to make crafts from plastic bottles with your own hands:

Cut the container to the height you need. Roll up the bright pages of the magazine into tubes with a diameter of 0.1 cm. Attach them to the base of the future vase, cut off just above the neck.
Wrap the cut bottle with paper and glue it.
Glue the tubes along the perimeter of the future vase so that each one is tightly glued to the next one.

Crafts from plastic bottle caps

Fridge Alphabet Magnets can be obtained using caps and other materials. Take:

traffic jams;
small magnets;
double-sided adhesive tape (glue);
medical alcohol;
colored paper;
markers.

How to do:

Degrease the surface of the plugs with alcohol.
Glue the magnet with glue or tape to its surface.
Cut out paper circles that match the size of the bottle cap.
On each circle, write a letter with a felt-tip pen. Glue the resulting workpiece inside the lid.

Video about what can be made from a bottle

If you have accumulated a lot of unnecessary containers, think about what you can do with plastic bottles with your own hands.

What can be made from plastic bottles

All kinds of crafts will help decorate the house, garden, Christmas tree. Creating products using the material is convenient and exciting for adults and children. The formation process develops imagination, fine motor skills. In addition, you can usefully use the plastic you do not need.

Peacock from plastic bottles

Do-it-yourself frog for the garden

How to round the edges of a plastic bottle

How to make the edges of a plastic bottle smooth and not sharp

Master Class

Many people very often create vases or other interesting crafts from plastic bottles, but they don’t know what to do with the cut edges, how to burn or knead them so that it would be beautiful. I will now tell you how to round the edges of a plastic bottle in a couple of seconds. This method is very simple and does not require a lot of auxiliary material, not everyone just knows this method.

For a mini master class, we only need an iron, naturally already heated, as well as a simple sheet of paper that will serve as a barrier that the plastic bottle will not stick to the iron. I will show how to round the edges using the example of a regular bottle. We cut a plastic bottle, or rather cut off the crown. We need the lower part, the one that is larger.

Then we take a plastic bottle, put a sheet on top of it, and iron it over the edge with an iron. Not too long, so that the plastic does not finally drip, we follow the process.

At the end, we should get such edges, they are neat and look great. Now you can create a vase from this plastic jar.
But remember, the denser the plastic, the longer you need to iron it, as it is difficult to melt wide walls through paper.

Many people very often create other interesting crafts, but they don’t know what to do with the cut edges, how to burn or crease them so that they look beautiful. I will now tell you how to round the edges of a plastic bottle in a couple of seconds. This method is very simple and does not require a lot of auxiliary material, not everyone just knows this method.

Then we take a plastic bottle, put a sheet on top of it, and iron it over the edge with an iron. Not too long, so that the plastic does not finally drip, we follow the process.

At the end, we should get such edges, they are neat and look great. Now you can create a vase from this.
But remember, the denser the plastic, the longer you need to iron it, as it is difficult to melt wide walls through paper.

And here we have such a craft in the future. How to do it, we can consider in the next article.

Also try to create or original, but it will require huge costs.

A greenhouse is one of the main components of a successful harvest, so you can’t forget about it. We suggest you make a greenhouse out of bottles with your own hands, using the tips below. Of course, the manufacture of such a greenhouse will take a lot of time and plastic containers, but we are sure that it is precisely such a country attribute created by you personally that will not only fulfill its direct functions, but will also become a special pride of your site.

The first way to make a greenhouse from bottles with your own hands:

We cut off the bottoms of plastic bottles and string the bottles on top of each other. In this case, you do not need a film.

To make the roof, we use the even middle parts of plastic bottles - we cut and straighten them in hot water using a press (a 3-liter jar of water will be an excellent load), as soon as the water cools, your blank will straighten up. Wire should be used to fasten parts, since nylon threads are not durable.

The second way to make a greenhouse from bottles with your own hands:

For the manufacture of the greenhouse, we will take two types of plastic bottles: from mineral water and dark beer bottles - the idea is that by alternating transparent and dark bottles, you can provide the plants with the necessary amount of sunlight.

For the manufacture of a greenhouse measuring 18 square meters. m. need 2 thousand plastic bottles. The process of making a greenhouse from bottles with your own hands is time-consuming, so you should be patient.

The basis of the greenhouse - shields

After collecting a sufficient number of bottles, we proceed to the manufacture of shields. To do this, on a long rail (the length of the rail is the height of the future greenhouse) with a furniture gun, we shoot our workpieces of the same length. Such a greenhouse is great for tomatoes, as they do not need high temperature.

If cucumbers are grown in the greenhouse, then the process of making a greenhouse from plastic bottles with your own hands should be slightly changed:

On a long rail (the length of the rail is the height of the future greenhouse), a thin baguette is nailed across. On this baguette we nail the film. Such a greenhouse is warm and durable. It does not require additional covering material for planting seedlings in the spring.

The third way to make a greenhouse from bottles with your own hands:

We prepare the bottles for the manufacture of shields: in the head part, the base of the bottle and along it we cut the “seams” - places, as it were, for gluing the bottle. As a result, we get a rectangular plate. Thus, we make the required number of blanks for the future structure.

Now we begin the manufacture of rails - transverse and longitudinal. For transverse fastening of the plastic film, rails are taken, the length of which is equal to the length of the plastic blank.

First, we make the frame of our shield, using a rail measuring 30x30 mm, the height of this rail should be equal to the height of the future greenhouse (in this case, 1.5 meters). This rail is stitched with a transverse rail equal to the dimensions of the plastic shield.

The next step in making a greenhouse from bottles with your own hands is to shoot bottle blanks with a furniture gun. To keep the greenhouse warm and not blown through, the joints of the blanks should be closed with strips of plastic bottles.

Similarly, you can make a gazebo for giving from bottles.

Do-it-yourself roof construction from plastic bottles