Roofing material uniflex. Roofing material technonicol uniflex ekp gray slate Uniflex consumption

Uniflex is a modern roofing material for the arrangement of roofs and waterproofing of building structures, produced by TechnoNIKOL. Being one of the varieties of euroroofing material, Uniflex material for roofing structures is a universal bitumen-polymer material widely used in the installation of roofs and to protect foundations and walls from moisture penetration. Based on the tests carried out, the material received a certificate of compliance with all regulatory documents and standards.

Uniflex is represented by a multilayer structure, the basis of which is fiberglass or fiberglass, or polyester film, on which an astringent bitumen-polymer layer is applied, consisting of SBS or APP modifier and mineral filler. A protective layer is applied over the bitumen-polymer layer, consisting of foil, coarse or fine-grained dressing and a film of polymer material.

Reliability and ability to operate in various climatic conditions. If Uniflex is modified with an SBS component, it becomes more flexible and can be used in regions with air temperatures down to -40°C. In the case of using APP as a modifier, the Uniflex component becomes more durable and resistant to thermal effects (its softening occurs only at temperatures above +150 degrees)

Long service life (20-25 years)

Improved performance. For example, the vapor permeability of the material is several times lower than that of traditional roofing material.

Uniflex TechnoNIKOL - one of the innovative developments - is made on modern equipment, has a certificate of compliance with standards and state standards, and is used in the construction of serious civil and industrial facilities.

There are two types of material, differing from each other in the type of dressing and scope:

Uniflex K. Differs in coarse-grained dressing from granulate or shale. There are varieties with a foil coating on the outside, and a polymer film on the inside of the canvas. Use this type of material as the top layer of the roofing "pie". It is represented by the following varieties: Uniflex EKP, Uniflex TKP, Uniflex HKP, Uniflex Vent EKV;

Uniflex P. It is characterized by double-sided coating of the canvas from a polymer film or fine-grained dressing. The main area of ​​application is the device of the lower layer of a multi-layer roof, as well as for waterproofing building structures (foundations, walls, etc.) Varieties of this type: Uniflex EPP, Uniflex TPP, Uniflex KhPP, Uniflex Vent EPV.

Technical characteristics of Uniflex K and Uniflex P also have a number of differences. In particular, the mass of a square meter of type P euroroofing material is 3.85 kg, while the weight of type K euroroofing material exceeds it by 30% and amounts to 4.95 kg / sq.m. The thickness of the sheets also differs: type K is 1 mm thicker than type P.

EPP

EPP is a rolled roofing and vapor barrier material, the reinforcing base of which is polyester, on which a bitumen-polymer coating is applied on the outside and inside, using artificial rubber as a modifier. Outside and from the side of welding, the material is covered with a melted polymer film. It has a certificate of conformity to all required GOSTs. It differs from other Uniflex brands in the following features:

One of the most durable varieties, with the maximum percentage of elongation at break (up to 60%);

High quality, due to the enrichment of bitumen with artificial rubber and a thicker binder layer on the welded side;

Excellent performance in any regions of Russia with a temperature minimum of up to -30 degrees;

Warranty period of operation - 20-25 years.

It is recommended to use Uniflex EPP for the manufacture of the bottom layer of a two-layer welded flat roof, while the top layer is recommended to be made of Uniflex EKP or Technoelast EKP. It is also used in the construction of facilities where waterproofing of underground structures is supposed.

Due to its structure, EPP has good vapor permeability. Vapor barrier Uniflex EPP is used in the installation of "breathing" roofs.

The average price of the material in the Russian market is 100-115 rubles/sq.m. The cost of one roll of Uniflex EPP will cost 1000-1150 rubles.

EKP

In Uniflex EKP, as in the previous variety of euroroofing material, polyester acts as a reinforcing base, thanks to which the material is able to withstand high tensile forces. The base is impregnated on both sides with a bitumen-polymer mixture, due to which the elasticity of the material increases and it can be freely mounted even at sub-zero air temperatures. The outer coating of the ECP, produced by TechnoNIKOL, is represented by a coarse-grained dressing of roofing slate.

On the market, Uniflex ekp is most often offered to the consumer in gray slate, although there are still green and red sprinkles. Performance characteristics allow using EKP as the top layer when installing a single-layer or two-layer welded roof. The thickness of the EKP web is 4.5 mm, the area of ​​one roll of the EKP is 10 sq.m., and its weight is 49.5 kg.

The price of the material per 1 sq.m ranges from 115 to 130 rubles / sq.m., while the cost of one roll is 1150-1300 rubles.

TCH

The peculiarity of this variety of euroroofing material is that frame fiberglass is used as a reinforcing base, which is characterized by special strength and high tensile strength in various directions. The protective coating of the material is formed by coarse-grained roofing slate. Consumers more often opt for Uniflex tkp gray slate, although there are also varieties of material with red and green sprinkles on the market.

The technical characteristics of TCH meet all the necessary standards, which is confirmed by the existing certificate of conformity. The weight of the TKP roll is 49.5 kg. Average price per sq.m. in the Russian market is 105-110 rubles, respectively, the cost of a roll is 1050-1100 rubles.

HPP

HPP technonicol is one of the inexpensive types of Uniflex, due to the use of fiberglass as a base - a durable, non-rotting synthetic base. Fused polymer film was used as a protective layer. The web thickness is 3mm. The technical characteristics of KhPP 3 make it possible to use the material in the arrangement of the lower layer during the installation of two-layer built-up roofs. The cost of the material is significantly lower than other varieties of Uniflex. The average price of the material is 80-85 rubles per sq.m.

CCI

Uniflex TPP as a reinforcing base has a frame fiberglass impregnated with a binder composition of bitumen and polymer. From the outer and welded sides, the material is covered with a protective polymer film. The material is used as a bottom layer during the installation of roofs, for waterproofing ground and underground structures. The operational and technical characteristics of the Chamber of Commerce and Industry are similar to those of Uniflex HPP.

The weight of a CCI roll is comparable to the weight of a HPP roll and is 38.5 kg. Price per sq.m. fluctuates in the range of 90-100 rubles. The cost of the material varies depending on the amount of euroroofing material purchased.

EPV

Uniflex Vent EPV is also called a "breathing roof", as the material effectively protects against moisture penetration, due to the presence of special channels in the roofing sheet, through which water vapor is removed. It is possible to use the material without dismantling the existing roof, which increases labor productivity and significantly saves time that must be spent on roofing.

Operational and technical characteristics are due to the peculiarity of the device of the Uniflex EPV canvas, the upper surface of which is treated with fine-grained sand dressing. From below, the surface of the web is formed by a ventilated layer consisting of strips of a bitumen-polymer mixture, between which fine sand is applied. The entire lower surface is covered with a polymer film.

EPV is used for the installation of the lower layer when installing a multi-layer roof, as well as for the reconstruction of roofs. The cost of the material is variable depending on the region, so the price per roll varies from 1760 to 1950 rubles.

HKP

Uniflex HKP refers to varieties of euroroofing material used for the manufacture of the top layer for the arrangement of multilayer welded roof structures. It is distinguished by the fact that the reinforcing base is fiberglass - a tear-resistant, non-rotten synthetic material.

Popular on the market is HKP gray slate, the technical characteristics of which are similar to analogues. Material price per sq.m. averages 95-108 rubles. The cost of a roll is 950-1080 rubles.

Next in line is the material TechnoNIKOL Uniflex EKP, the technical characteristics of TKP, EPP, CCI, as its modifications, will also be considered in the article.

Uniflex is perhaps the most famous modern roofing and waterproofing material produced by TechnoNIKOL. Its base is a polyester or fiberglass cloth, which is usually coated on both sides with a layer of polymeric bituminous binder, which consists of the chemical substance styrene-butadiene-styrene (the so-called SBS), dolomite (talc) as a mineral filler + polymer- modifier. The upper protective layer is a sprinkle of various grain sizes or a film (sometimes foil).

In order not to be confused, you must immediately deal with the labeling of the product. What does the abbreviation Uniflex EPP, CCI, EKP or TKP mean? And do the specifications of these brands differ?

An ordinary developer needs to know the following.

• The middle letter "P" in the name means that the panel is covered with a polymer film on both sides. Therefore, this brand of Uniflex (EPP, TPP) is used mainly as the lower working layer in the construction of multilayer waterproofing.
• The letter "K" indicates that the sheet on the front (outer) side has a coarse-grained dressing, on the other side, the deposited side - only a polymer film. It is clear that this brand of product (EKP, TKP) can be used for the installation of the upper layer of the roof (with the function of sun protection and general waterproofing).

Tabular values ​​of the technical characteristics of the Uniflex material (EKP, TKP, EPP, CCI)

The table shows that this building material has excellent waterproofing qualities and characteristics, which allows it to be widely used in the construction of a wide variety of building structures.

It perfectly insulates not only rooftops, but also basements, etc.

Uniflex TechnoNIKOL is modified with polymers, and therefore has a technically increased bio- and heat resistance, as well as flexibility (even at negative temperatures).

Products are usually produced in rolls with an area of ​​10 m2. Today's price is approximately 133 r/m2.

Are there any usage restrictions? There is.

Uniflex EPP is a roll waterproofing material based on bitumen and polymer. It is applied to isolation of a roof and other constructive elements of buildings. This is a demanded rolled waterproofing in Moscow due to the combination of low price and excellent performance.

Waterproofing Uniflex: structure and scope

Uniflex is made by applying a bituminous composition (SBS-styrene-butadiene) to a polymer base on both sides. The protective layer is a fine-grained dressing based on talc, foil, dolomite. The top layer is a water-repellent film. The manufacturer TechnoNIKOL produces Uniflex EPP using high quality raw materials. Rolled waterproofing Uniflex has successfully passed tests in an accredited laboratory Tekhnonikol for compliance with GOST EN 1849-1-2011.

Buy waterproofing Uniflex EPP can all those who perform work to protect structures from moisture and condensate. The material is suitable for use in all climatic zones as lining insulation for all types of roofs, foundations, swimming pools, floors.

Uniflex EPP - price and other advantages

Buy Uniflex - from 119 rubles. for 1 m2 in our TeploSnab online store. The low price of Uniflex waterproofing is explained by direct deliveries from the manufacturer. Roofing material has the following advantages:

• high tensile strength;
• minimal water absorption (up to 1%);
• long service life;
• elasticity and flexibility;
• ease of installation;
• does not require maintenance;
• resistance to temperature changes.

EPP waterproofing is supplied in rolls. The material is easily cut with a polymer knife.

Specifications

Features of working with the material

Before buying Uniflex and installing waterproofing, it is recommended to study the TechnoNIKOL manufacturer's instructions. Roof waterproofing is laid in accordance with SP 131.13330. Before installation, the material is heated with a burner or a heat gun, rolled out with an overlap. For better adhesion, the surface to be insulated is coated with bitumen.

Purchase and delivery

Uniflex is multifunctional and versatile with a wide range of applications. A bitumen-polymer binder is applied to a polyester or fiberglass base with a special filler and thermoplastic elastomer in the composition. For additional protection, sprinkles, film and foil are used.

Uniflex is a business class material that combines practicality and favorable cost. When choosing, it is necessary to clearly present the tasks set, and then the result will fully pay off all investments. It is also important to follow the installation rules. An almost complete analogue of Uniflex roofing material is. The finished coating will be of high quality and durable, and at the same time it will not require complex maintenance and will not cause other troubles.

Uniflex: technical specifications

Features of installation and use of Uniflex

Depending on the type, Uniflex is used for waterproofing structures and roofing. According to the manufacturing technology, several types are distinguished for creating the upper and lower layers (K and P, respectively). Installation is carried out on pre-treated horizontal or vertical surfaces using a propane burner.

Uniflex is quite versatile, so it is suitable for different climatic regions. This is the simplest way to solve the problem of protecting structures in the implementation of the most complex construction projects. Additionally, the material is suitable for the restoration and restoration of old coatings, including ruberoid roofs. The use of advanced technologies guarantees impeccable quality and a long service life.

Uniflex material modifications:

• - fiberglass base, top layer slate, bottom layer film
• - the base is fiberglass, the top layer is a film, the bottom layer is a film
• - the base is fiberglass, the top layer is slate, the bottom layer is film
• - fiberglass base, top layer film, bottom layer film

Roofing material, including the arrangement of waterproofing, which is called Uniflex, is produced by TechnoNIKOL. This material belongs to the class "Business". In addition to the Uniflex brand, Ecoflex also belongs to this class from the category of rolled bitumen-polymer building materials. The main advantage of these brands can be called a long service life, the minimum period is 15 years, and the longest is 25 years.

Initially, it is worth mentioning that three types of bitumen rolls are produced under the Uniflex brand. Let's take a closer look at this material:

1. In principle, Uniflex is a waterproofing for various structures.
2. Uniflex VENT EKV, TPV, EPV is used for the arrangement of ventilated roofs. The designation "EPV" and "TPV" on the material indicates that they can only be used for the lower layers of roofing carpets, but the designation "EKV" indicates that the outer layer of this material is covered with coarse-grained dressing, and is intended for laying as outer layer of the roof. For repair work on old roofs, which do not need to be completely dismantled, and there is no certainty that the insulation under the old coating will be dry, the laying of Uniflex VENT will be an excellent solution. Since this roofing material is breathable and will not allow swelling of the coating from the inside.
3. Also, the Uniflex coating can be marked with the marking "K" and "P". "K" indicates that the outer layer is made using coarse-grained dressing, and "P" is the outer layer of polymer film. The second type is used for arranging waterproofing in the form of an inner layer of a roofing pie, and the first type is for the outer layer.

Bitumen-type impregnation, which is used in this material, incorporates SBS thermoplastic and fillers. The manufacturer does not declare any restrictions on the climatic conditions for the use of this roofing material.

Consider some of the technical qualities of TechnoNIKOL Uniflex, which is used for arranging roofs.

The Uniflex EPP marking indicates that polyester is taken as the base, and the lower and upper layers of the bitumen coating are protected by a polymer film. The material has a thickness of 0.28 centimeters, and the mass of the square of the canvas is almost 4 kilograms. To tear such a web longitudinally, it is necessary to apply a force of 500 N. Well, to break the web across, it is necessary to apply a force of 350 N.

Uniflex Chamber of Commerce and Industry has the same mass and thickness, but fiberglass is taken as the basis here. The protective layer is a polymer film, but due to the use of a different type of base, it is much stronger. For a longitudinal rupture, it is necessary to apply a force of 800 N, and for a transverse rupture, 900 N. The material with any marking retains its flexibility on a bar with a diameter of 0.5 centimeters at a temperature of - 20 degrees.

Uniflex HPP

Uniflex HPP can withstand the smallest breaking force, it has fiberglass as a basis and can be torn with a force of 294 N. All of the above material of any type is produced in rolls, each roll is 10 meters long and 1 meter wide. The level of heat resistance is quite high and reaches 95 degrees.

Uniflex EKP is equipped with external protection in the form of a coarse-grained topping, and it can be laid as the top layer of a roofing cake. Representatives of the manufacturer in most cases offer Uniflex gray EKP slate, but red and green sprinkles are available. Uniflex EKP 4 5 is used to decorate roofs with large slopes or for inverted roofs.

The Uniflex TKP type, just like the EKP, has a weight of one square of 5 kilograms and a thickness of 0.38 centimeters. Other technical characteristics are the same as those of the Chamber of Commerce and Industry.
Uniflex HKP, in addition to the composition of the outer protective layer, does not differ in any way from the HPP type.

To eliminate all complaints from buyers, which are caused by a lack of understanding of how to properly lay this roofing material, the manufacturer offers detailed laying instructions for both new roofing and repair work. In addition, in many areas, dealer companies provide training to groups of roofers, where they are taught how to comply with all conditions for working with different types of roofing materials.
You can watch the work with Uniflex on the video:

Roofing material laying