If the zipper is broken. How to fix zippers on jeans? simple Rules for using the lock for long work. (Edit)

It happens that the zipper lock diverges at the very wrong moment. You can, of course, show efficiency and quickly take the thing for repair, so that the lock is repaired by the master. But if there is no such possibility, then what to do then? How to fix the lock and deal with the problem on your own?

How to clamp a slider on a zipper?

How to fix a lock if there are no teeth?

The lack of teeth on the zipper is serious problem, which is very difficult to cope with at home. If there are metal teeth in the lock, then you can borrow them from another zipper. The teeth must be the correct size. It is quite difficult to insert them into the lock, so if you can’t cope with the problem on your own, it’s easier to take the thing to the studio for repairs.

A nylon or plastic zipper is easier to repair. You can insert the teeth with a thick fishing line. But it is necessary to fix them so that the ends do not interfere with the slider moving around the castle.

The zipper doesn't close and unzip well.

How to put the zipper teeth in place?

More often this problem worries the owners of metal locks. The teeth simply go out of order, thereby making it difficult for the “dog” to move. To solve this issue, you just need to tap with a hammer on the lock itself, in the very place where the teeth come out of the general row.

How to take care of locks?

1. One of the main enemies of lightning is sand. If he gets into the castle, then he inevitably begins to diverge. Therefore, it is advisable to carefully monitor the cleanliness of the shoes, apply a special cream on it and clean the lock with a regular cotton swab, removing dirt from the surface of the fastened zipper. This will help remove heavy dirt from the lock.
2. In addition, in order for the lightning not to disperse on things, they must be washed properly. Fasten the zipper and turn the product inside out before washing.
3. Iron things with nylon or plastic zipper Be very careful not to damage the teeth.

Often you have to deal with an unpleasant situation when your favorite thing can not be put on due to problems with the zipper. Especially often the zipper on a jacket or sweaters diverges, since the fastener tape in such clothes is quite mobile and can be easily damaged.

Why does the zipper on the jacket diverge?

The zipper on the jacket diverges: the main problems with the fastener

A zipper has several common types of damage:

The lock diverges - the reason is that the slider is too loose, it does not bring the teeth together;

The slider moves too tight - on the contrary, the slider planes are very compressed, friction prevents it from sliding;

· the pawl flew off the clasp - the fasteners were weakened so that the working part of the mechanism slipped past the limiters;

The lock unfastens spontaneously: again, the slider is weakened, strong pressure on the joints also plays a role.

It’s easy to figure out how to fix a zipper on a jacket or jeans: if unfastening is difficult, you need to lubricate the teeth, for other problems, tighten the slider or replace it. However, the replacement solves the issue with poor unfastening.

You can squeeze the planes of the dog with pliers, but you need to do this carefully, since too much compression will lead to a problem of the second kind - with unfastening. In addition, the relatively fragile metal of cheap accessories can simply break. To lubricate the teeth, it is most convenient to use a soft graphite pencil. It is enough to run them over the teeth several times from the outside and inside ribbons and fasten and unzip.

With spontaneous unfastening - this usually happens with tight jeans - let's say a variant with a stopper. It is enough to pass a ring through (from a keychain made of ordinary wire or unbent paper clip) into the hole on the tongue and put it on when buttoning the button of the jeans together with the loop.

If the fix fails

The fastening mechanism that has flown down from the zipper is easiest to replace in the workshop, they can easily pick it up there right size and fix it professionally. However, if you wish, you can do it yourself. The easiest option is to remove the stops at the top of the fastener and, carefully bringing the ends together on a flat surface, put the slider on them. At the same time, it will need to be slightly tightened after putting on and restore the limiters. The easiest way is to sew tightly with a thick thread upper part lightning. If the clasp is sewn into the product, this option is not suitable.

When the pawl (or slider) of a one-piece zipper completely comes off, it may seem that it is simply impossible to fix the problem. However, there is an easy way to put the slider back in place. To do this, you only need to take pliers and new top or bottom zipper stops. Very soon your lightning will be back in working order!

Steps

Part 1

Buy a new zipper dog if old detail damaged. If the old slider is broken or doesn't work well, you will need to buy a new one instead. Replacement sliders can be purchased at fabric and craft stores.

• Make sure the new pawl is the same size as the old one and is the correct size for your type of zipper. It would be best to take an old dog with you to the store.
• You can also try to buy a ready-made zipper repair kit in needlework supplies, which will have everything you need to replace the pawl and install the upper and lower stoppers on the lock (if necessary). Otherwise, you will have to separately purchase a pawl for the zipper and stoppers for the lock.

1. Use pliers to remove a few teeth from the end of the zipper. To return the slider to its place, you need to expose small plot woven zipper tape near its end. Remove teeth one at a time with pliers. Continue working until you have exposed about 5 cm of webbing on both halves of the zipper.

   • Try to remove the minimum possible number of teeth to return the dog to its place. If the slider is very small, you may need to strip even less than 5 cm of the zipper.
   • Consider the condition of the zipper before removing the teeth from it. If the zipper is open, then the teeth will have to be removed from its lower edge. If the zipper is closed, then the teeth will need to be removed from its upper edge.
   • Make sure you strip the same length of fabric tape on both halves of the zipper. If the sides are different, then you may not be able to return the slider.

2. Attach the slider to the zipper. The direction of the zippered pawl will differ depending on whether the zipper was open or closed when the pawl popped off.

   • If the zipper is open, put the pawl on it with a forked hole so that the combined hole at the back of the slider looks away from the zipper itself.
   • If the zipper is closed, slide the slider over the zipper with the combined opening so that the forked opening of the pawl on the other side faces away from the zipper.

3. Pull the halves of the zipper over the pawl. In order for the dog to finally sit on the zipper, it is necessary to pull on the fabric sections of the zipper on both of its halves above the slider. This will apply enough force to move the pawl from the fabric to the zipper teeth.

   • Keep pulling the zipper until you hear a distinctive click. He will talk about the fact that the dog sat down in its place.

4. Check the operation of the lightning after the final installation of the slider. Try moving the slider up and down a few times to see if it works. If the dog successfully fell into place, then it will easily unfasten and fasten the lock. If the pawl warps and does not move, you probably need to try reinstalling it again.

   • Be careful not to accidentally remove the pawl from the zipper while checking its operation, while you have not yet installed the upper or lower stops on the lock.

   Part 2

   Attach top and bottom zippers

   1. Think about which stoppers are best for you - top or bottom. After removing part of the teeth of the zipper, it will be necessary to limit this area with upper or lower (square) stoppers so that the pawl does not come off again. Top stops are usually small size and are separately attached to each half of the zipper. The lower stops are usually larger, have square shape and are fixed at once on two halves of the zipper over the gap between these halves in order to prevent the slider from jumping down and fixing the end of the zipper in the closed state.

      • Top stoppers are suitable for the top of the lock, as they do not allow the dog to come off again, but do not interfere with unfastening and zippering at this end.
      • The lower (square) stoppers are suitable for the lower end of a one-piece zipper, as they do not allow the dog to come off and allow you to partially cover the bare area of ​​\u200b\u200bthe zipper fabric tape where the teeth were removed.

   2. Install the top stoppers onto the zipper with pliers. If you decide to install top stops on the zipper that will not allow the slider to come off from above, place the first stop directly above the first remaining tooth of one of the halves of the zipper. In order for you to be able to do this, the zipper should be slightly opened. Once the stopper is in the right place, pinch it with pliers to secure it.

      • Make sure the stopper is tight and will not move or come off when the lock is closed.
      • Install top stoppers on both halves of the zipper to ensure that the dog does not come off the zipper again.

   3. Install the bottom stopper. If you decide to use the bottom stopper to partially cover the exposed section of the zipper from the bottom, insert the stopper's mounting pins into the fabric of both halves of the zipper. The stopper should be located directly under the bottom remaining zipper teeth. Before performing this operation, make sure that the zipper is fastened. After installing the stopper with front side, turn the item or fabric inside out so that you can bend the mounting pins towards each other with the help of pliers from the inside.

      • Make sure that the mounting pins are tight enough (until flat) and that the stopper itself is securely locked. It is very important that the pins are flat against the zipper, otherwise they will snag or scratch you.

   4. Despite the fact that zippers are for the most part reliable fasteners, sometimes they can still break or stick. When this happens, it's easy to get frustrated with the fear that you'll have to change the whole zipper. However, there are several various ways, with which you can try to fix the zipper so that it does not have to be changed. With a little effort, you can sometimes fix a stuck or broken zipper and solve a whole host of other zipper problems.

      Steps

      How to fix a stuck zipper

      Lubricate the zipper with graphite. When the zipper slider simply refuses to move, applying lubricant can cause it to budge. Try rubbing graphite on the zipper teeth to lubricate them.

      Use liquid detergent. If graphite does not help, put a drop of liquid detergent to straight lightning. The soap will provide additional lubrication that will allow you to move the stuck slider. Follow the steps below to lubricate the zipper with liquid detergent.

      Wash the item, and then grease the zipper. If graphite or soap did not help you fix the zipper the first time, you can wash the item and try again. Ultimately, washing will remove grease, grease, dirt, and other foreign matter from the zipper. This way you will completely clean the zipper before the next lubrication.

      How to fix diverging lightning

      1. Reduce the pressure on the zipper. Lightning can diverge due to the fact that excessive pressure is applied to it. If you reduce this pressure, it will be easier for you to fasten and/or repair a broken zipper. There are several ways to reduce the load on lightning, which are mentioned below.

         Clean the zipper teeth from dirt. When dirt builds up on the teeth of a zipper, it can prevent it from closing. For this reason, you need to clean the zipper teeth and free them of anything that might interfere with the zipper.

         Straighten bent zipper teeth. If all else fails, you may need to straighten the bent teeth of the zipper to get it to close. Even though this may seem like a difficult task, it is not that difficult.

      How to fix a problematic zipper slider

      Assess the degree of lightning damage. If the zipper on your favorite coat keeps coming apart, inspect it to assess the extent of the damage. Sometimes the source of all problems can be a damaged or broken slider. In some cases, the problem can be quickly fixed.

      Remove the top stoppers from the zipper. Before you start fixing common problems, you will need to use pliers to remove the top stoppers from the zipper. This is very important to do, because otherwise you will not get full access to the lightning teeth and will not be able to assess its condition or the condition of the slider itself.

      Remove the slider from the zipper through the top and inspect it. Look at the slider on the side. Check how even the gap between the top and bottom of the slider is. The uneven gap does not allow the slider to connect the zipper teeth evenly, which causes them to diverge.

      Install the repaired or new slider in place. After fixing the old one or purchasing a new slider, you will have to install it back onto the zipper teeth. In doing so, observe the instructions below.

      Check the functionality of the slider. Try zipping the item as normal to see how well the slider moves up and down the zipper teeth. In some cases, lightning problems may remain.

      Reinstall the top zipper stops. After returning the slider to its place, you need to install the upper zipper stoppers back, directly above the top pair of cloves. In the absence of limiters, the slider will jump off the zipper, which will not allow it to be used normally.

      How to fix a zipper with a missing bottom tooth

      Remove the lower zipper stopper. The bottom stop is the part that the zipper slider rests on when it's all the way down. To fix the problem with the missing bottom zipper prong, you will have to first remove the bottom stopper.

      Open the bartack stitches at the bottom of the zipper. A bartack is a small line of stitches that securely secures the bottom end of a zipper to clothing. By removing the bartack, you will have full access to the lower teeth of the zipper. This is important to do as you will need to fix the problems with all of the zipper teeth in order for it to work properly.

      Install a larger bottom stopper on the zipper. Installing a larger limiter will allow you to close the hole from the missing clove. Thus, the lightning will start to work normally and will no longer get stuck in this place in the future.

      Restore the fastener. After installing the new stopper, you need to restore the bottom bartack to securely attach the bottom edge of the zipper to your clothing. To do this is quite simple.

      How to quickly fix unexpected problems

      Replace the broken puller with a new puller or paperclip. A broken puller, whether on boots, trousers or a jacket, does not allow you to grab the zipper firmly enough to fasten it. Luckily, similar situation can be quickly corrected without much effort.

      Use the key ring to secure the trouser zipper with it. A zipper that pops open is one of the most annoying problems you can have with pants. And this is true, because this always happens at the most inopportune moment.

      Zip up the split zip. A fairly common problem is when the zipper does not fasten due to problem runner. Fortunately, it will take you very little time to zip up in such a situation.

      • Be patient and be prepared to try several ways.
      • Contact your nearest fabric and craft store for help and advice.
      • Do not use graphite to lubricate white or dyed bright hues lightning.
      • If you do not have graphite or detergent on hand, you can use other types of lubricants. Try using lip balm, window cleaner, candle wax, or petroleum jelly. Test the selected lubricant on an inconspicuous area of ​​​​the item to make sure that it does not leave stains or ruin the item.
      • Instead of a traditional puller, a cute keychain can be installed on the zipper slider.

      Despite all the instructions for repairing lightning, still in 95% of cases best repair is a replacement.

      It's all the dog's fault

      So the most common repair is due to the fact that the zipper diverges during its fastening. Repair is such - the replacement of the dog. But if there is no place nearby to buy a dog, then you need to take pliers and press the front and back sides of the dog to each other when buttoned. But when you press it, in no case do not press on the middle, where there is a protrusion with a groove for the fastener. Otherwise, you can simply break it or damage the latch.

      The paperclip is the best detail

      If the clasp comes off, then insert a paper clip instead, you walk like a "loh", but with a working lock

      Too big belly

      There is such a problem that everything seems to be working, but as you push it, the lightning breaks. No one can help here, just the teeth of the zipper itself have worn out, it is necessary to change it to a new one ...

      Broken main tooth

      Pretty too common problem, it seems like it is still working, but at the bottom of the zipper, the plug-in clove broke off or cracked. There is also a problem with him, the only way I found is to fasten the zipper somehow and sew the bottom to each other. After that, the jacket has to be worn over the head or legs. By the way, I haven’t tried it myself, but I think that you can put a second dog, it will probably delay the discrepancy of the teeth. Well, or another option - a replacement.