How to measure an interior door. Entrance door dimensions. Do you need extensions and what width

An important milestone the manufacture of the door is the removal of the dimensions of the opening. If the door is smaller than the opening, it will not be possible to install it, or the door will be poorly fixed, unreliable, which will not allow it to fully perform its functions. If the door is larger than the opening, it will take time, certain skills and costs to expand it, which is also undesirable. Therefore, the measurement of the size of a metal door must be approached very carefully.

To measure the opening of the front door, it is necessary to free it from old design. If the dismantling of the old door is currently impractical, the opening must be freed at least from the platbands so that the walls are free. If, during dismantling, part of the wall collapsed, it is necessary to eliminate this shortcoming and only then proceed to measurements. It is also necessary to free the opening from finishing materials, that is, take measurements directly on the walls.

How to measure the opening and entrance metal door for installation

You can measure the opening under the door as follows.

1. Take a centimeter and measure the width and height at several points. It must be remembered that openings that are ideally even from a geometric point of view do not exist, the width and height can “walk”. So, the width is measured from the bottom, top and middle. The same goes for height.
2. Some openings may narrow or, conversely, expand towards the exit. This must be taken into account. Also remember that the walls may have vertical deviations, therefore, when taking measurements, use a plumb line or a laser builder.
3. Width and height are measured first while standing inside the room, and then outside. If the apartment is being renovated and you have not done the floor yet, it is better to wait a little with door measurements. In addition, thresholds must be removed from the floor, they will interfere with measurements.
4. AT standard rooms the dimensions of metal doors are from 800 to 900 mm in width, from 2070 to 2300 mm in height. The dimensions of the door structure should be 2-3 cm smaller than the opening so that the unit can be adjusted during installation. The gaps will then need to be filled with mounting foam. However, the opening should not be more sizes doors more than 7 cm wide and 3.5 cm high. Otherwise, the door will be less resistant to breaking.
5. To measure the thickness of the wall in which it is intended to mount door block using a caliper. If it is not available, it can use two rulers. You need to vertically attach them to the wall on one side and the other. The distance between the rulers is the thickness of the wall.

In order for the front door to look attractive and durable, it is necessary to carefully measure the dimensions of the opening before purchasing and installing it, and determine the parameters for installation. Such dimensions are important in order to ensure the safety of the house. It is the front door that performs protective, and not just decorative functions. To properly measure the entrance metal door, you will need the most simple tools. Do not forget that the door leaf is not everything, you need space for door frame, for fastening the entire structure. Will be required additional accessories in the form of loops, handles.

The metal structure must be suitable sizes. Most often installed swing structures, which can open in different directions. It is best if it opens outward, such a model cannot be knocked out, it is safer. These doors are more convenient, they save inner space are comfortable in terms of their use. The doors themselves can be not only single-leaf, but also double-leaf, half-open. For work, it is necessary to completely free the opening from the platbands, to carry out repair work. If required, the walls can be reinforced.

Entrance door dimensions

The English system for measurements is rarely used today. Standard parameters the following:

1. The height of the canvas is 6 feet 6 inches, which corresponds to 198.1 cm. The width is 2 feet 3 inches, i.e. 68 cm
2. The standard height can be 6'8" which is 203.2 cm. The width is 2'9" which is 84 cm.

Most often, the metric system is used for measurement, it corresponds to SNiPs, which apply to all residential premises. Traditionally, the dimensions can be as follows:

• 2419x1910 mm;
• 2170x700 mm.

But we must remember that for ease of use, the width should be approximately 910 mm. In this case, there will be no problems with the entrance. According to the metric system adopted today for the doorway, the following parameters are applied:

• for normal - 2040x826;
• for reinforced metal - 2050x860 (9660);
• a design with two doors, for which metal is used, can have dimensions of 2000 (2050) x 1600 mm, the parameters of each leaf can be different, but most often one of them is made wider than the other, which allows you to easily bring overall furniture into a house or apartment, household appliances etc.

Taking measurements

Before ordering a metal product, it is necessary to take measurements correctly, i.e. determine what the width and height should be. This work can be done in several stages:

1. First you need to provide an indent for the wall. If the door has already been, then it is required to dismantle not only the canvas, but also the platbands in order to accurately set the parameters. Width and height are clearly defined from wall to wall and from the top of the opening to the bottom.
2. A tape measure is used to measure, all readings must be recorded. It is necessary to measure 2 points near the corner parts of the opening. This will allow you to immediately determine if there are any distortions. If the dimensions do not match those required, narrowing or widening work may be required.
3. In order to correctly measure the front door made of metal, it must be taken into account that the weight of the structure will be significant. May be required additional work by amplification. Therefore, the walls need to be checked for strength. If required, repairs are carried out. Usually this is the strengthening of the opening, the plastering of the walls.

Door leaf selection

To get data for iron door, you must immediately decide in which direction it will open.

Usually the height is standard, it is 2000 mm, but it is possible to manufacture canvases with a height of 1500 mm to 2300 mm, while maintaining a step of 10 mm.

The width can also be different, it is 600 mm, 700 mm, 800 mm, 900 mm. Other sizes are ordered individually, but the cost will be higher, we must not forget about this.

It is important to remember that during construction, all openings are planned in such a way that it is easy to pick up a box and a door leaf under them. If the input structure is required for already finished house, measurements must be taken carefully.

The following ratios are possible:

• with a width and height of the canvas of 60x200 cm, the width of the opening can be 63-65 cm, and the height - 205-210 cm;
• with a width and height of a double-leaf structure of 2x60x200 cm, the width of the opening can be 128-130 cm, and the height - 205-210 cm.

After completing the measurements, it is necessary to familiarize yourself with the given table indicators. This will make it easier to choose a door frame and leaf for a particular case. Only part of the data is given as an example.

To input steel door installed firmly and reliably in the prepared doorway, measurements should be taken, and then determine what parameters the box and canvas should have. Today, builders adhere to certain standards in order to easily select a product. After taking measurements, you can use special tabular data showing the ratio of the canvas and the opening. If the parameters are non-standard, you will have to pay extra for an individual project.

All buyers of wooden interior doors always ask the same question, how to measure the openings correctly, or how to measure when there are still old doors with frames and platbands in the openings. Therefore, we decided to tell in detail how to take measurements in order to correctly and accurately calculate the cost of the entire door block.

Instruments

To do this, we need inventory for measuring:

1. A sheet of paper or notepad (on which the result of the measurements taken will be recorded).
2. Pen or pencil.
3. Roulette (preferably 3 meters).

How to measure?

We will be consistent and tell you about 1 measurement method (an empty building opening.)

• you need to measure the height of the opening (from the floor to the top of the opening);
• opening width (from wall to wall inside the opening);
• the thickness of the opening (that is, our future - the width of the box);
• you need to decide whether there will be thresholds or not;
• indicate the opening of the doors, inward or outward, will the door be left or right?

Note! In order to find out the right or left door. Let's face the opening future door so that the door opens on itself, if the hinges are on the left side, then this door will be called (left door). If loops with right side then, accordingly, we will have it (right door)

It is also worth considering which doors will be locked with a latch (mainly a toilet, bathroom, bedroom), it is possible that the door needs to be locked if it is the 2nd door that is opposite the entrance armored doors or the door to the office, which also largely affects the choice of door. Maybe there should be sliding system- all these points must be indicated, since more full information will allow you to choose a door that will serve faithfully for more than one year.

Advice! Here, according to these measurements of the opening, you can accurately calculate the door block. But in any case, it is better to order doors in a specialized Woodenhome store where you will be offered a free professional measurer who will make a more accurate measurement, which will save you from unnecessary problems, since even minor differences in size can lead to big trouble during installation.

The 2nd method of measuring is a little more complicated than the first one, since it is in the opening (there are old box doors and thresholds with platbands)

To do this, you will need the same inventory for measuring;

1. A piece of paper or notepad. (on which the result of the measurements taken will be recorded).
2. Pen or pencil.
3. Roulette (preferably 3 meters).
4. Square for a more accurate measurement (the width of the old box) or the thickness of the wall of the opening.

In the 2nd measurement method, we will also be consistent

Need to freeze:

• door leaf (height and width);
• the width of the box (that is, the thickness of the wall);
• and of course, for a more accurate measurement, it is necessary to carefully tear off the old casing without damaging it on each side and measure doorway in height and width, this is done because different manufacturers doors and frames can make boxes 50 and 60 mm thick in their thickness, but now boxes are made 40 mm thick. And concrete openings are also wider on the one hand, on the other, if you look at the view from the top, it looks like side walls trapezoid.

More detailed information look at http://www.woodenhome.com.ua/doors-size-measuring.html how to measure doors correctly?

Additional Information

Another important point– always need to take into account such parameters;

• height or thickness of the future floor;
• the thickness of the tiles on the floor and on the walls;
• what gap to leave between the floor and the bottom of the door (maybe they want a thick carpet.

On many measurements there is no floor or tiles on the floor or on the walls, but at the same time, buyers can already order doors if there is information about those parameters that were listed above. Because the production wooden doors according to all State Standards and standards cannot be made faster than 1.5 months from the moment of measurement. And while the floor and tiles are being laid, half of the time for the production of wooden doors will already pass and the buyer will not have to spend extra time waiting for door delivery.

That's what you need to consistently correctly, accurately, measure doorways because your future order depends on it and correct installation. Buy quality door from solid pine, oak, ash and alder, you can always at Woodenhome. For orders and consultations call 098 680 23 65.

How to properly measure doors

What do you do before you buy new clothes? Determine your size. Doors are an outfit for your apartment, and here it is very important to know the exact dimensions so as not to make a mistake when buying. There is a fairly simple general system to help you get the right interior doors in Tula .

Opening dimensions

Before you start measuring, make sure that nothing will interfere with you. There should not be anything superfluous in the opening, remove old box, platbands, bare walls should remain. Usually standard width openings in the apartments are approximately 0.9 meters, and the height is 2.1. It happens, of course, and more, up to 2.3, so check the measurement to avoid mistakes. Then we need to take into account the fact that before the door leaf is installed, the box and insulation will take their rightful place in front of it. Their total thickness will take approximately 2.5 cm. But we have two slopes, which means that we multiply this figure by two, subtract the resulting amount from the width of the opening. For example, if we have an opening width of 0.86 meters, then the following formula goes 0.86-0.025 * 2 = 0.81 meters. So we got the size of the door leaf. In exactly the same way, we calculate the height, with the only difference, there is no need to multiply the thickness of the box by two. It has three sides, and the lower element is missing there. This formula is equally good for measuring both wooden and metal doors.

Wall thickness

In order to measure the thickness of the walls, it is best to use a caliper, it will help you accurately, quickly and conveniently calculate the dimensions we need. But if your house doesn't have one useful tool, do not be upset and do not rush to the store. It is quite possible to replace it, for this we use a cunning system. Place rulers on both sides of the doorway, measure the distance between the ends protruding from the opening. If your apartment is not located in a new building, but, for example, in a Stalinist building, then the thickness of the wall there can be much greater than in other houses. For such cases, you will need to install additional slopes.

If you decide to change everything at the same time interior doors and buy the same models in one place, you can get a "pleasant" surprise. When the boxes that fit perfectly into the living rooms are absolutely not suitable for the kitchen or bathroom. And most often a small threshold is to blame for this, it was he who stole such necessary centimeters of your house. If you forget about it, you will have to shorten the doors. This is extra hassle and serious damage to the aesthetic side. And metal or plastic doors generally not subject to such manipulations.

Before you start measuring, make sure that the walls and ceiling are completely finished. It would seem that the plaster, that it can change, or also the flooring. But believe that sometimes these millimeters can play a decisive and fatal role in your repair. Don't buy doors in Tula until major repairs are completed.

Before order interior door it is required to determine the dimensions (height and width) of the canvas and the need to use extensions. For the correct measurement of parameters, you need to use a tape measure.

The width and height of the doorway must be determined in three places - from below, in the middle and from above, choosing smallest value out of three. In addition to these indicators, it is also required to know the thickness of the wall, according to this value, extensions are selected.

Measuring the opening for the installation of interior doors

Using a tape measure, the width, height and thickness of the walls in which it will be installed are determined. door structure. Any changes during the installation of the product must be taken into account. For example, leaving room for styling facing tiles or floor covering. If the wall thickness is more than 7 cm, an additional element must be ordered. It is sawn and adjusted to size directly during the installation of the canvas. Extras are made different widths, when taking measurements, keep in mind that the products are included in the box by 1 cm (Telescopic molding system).

Web Width Determination

Standard canvases are produced with a width of 60 to 90 cm and a height of 200 cm. To accurately place the door inside the opening, it is necessary to leave an additional margin of 7–10 cm. Here is a small selection of indicators of the dependence of the parameters of the leaf on the width of the opening:

Add-on options

Products are a plank for masking a section of the wall visible in the opening. To correctly calculate the width of the element, you need to measure the thickness of the wall and subtract the thickness of the box beam. The standard thickness of the door frame is 7 cm, with thicker walls it is necessary to order extensions.

The width of the products must match the section of the wall to be closed, or be greater than it. For example, if the wall is 15 cm and the box is 7 cm, you should purchase an additional 9 cm.

How to determine the height of the canvas?

This parameter is determined by the side slope on both sides. Standard products have a height of 200 cm. With a higher opening, if the size is from the floor to top wall more than 210 cm, after installation, a gap is formed that will need to be closed. There are two ways to solve the problem - to lay free space, building up a wall, or order a door custom size. Sometimes the height of the opening can be less than 203 cm, then the door will not enter the existing space. The problem is also solved by two methods - a door of a non-standard size (190 cm) is ordered, a wall is cut to increase the size of the opening.

When conducting repair work doors are installed at the final stage, after finishing the floor, ceiling and walls. If you need to complete the installation earlier, then when measuring, take into account the thickness of the floor covering after its installation (subtract this figure from the height of the opening).