Diagram of a round umbrella. Series 5.904-51

The main characteristics of the umbrella

Designation	Dimensions, mm					Weight, kg
	t	D0	D	H	H1
3К.00.000	0,7	200	350	240		2,0
-01	1,0	250	450	257	150	2,85
-02	1,0	315	550	275		4,0
-03	1,0	400	700	400	250	7,1
-04	1,0	450	800	415		8,4
-05	1,0	500	900	480		10,1
-06	1,0	630	1130	523	300	14,0
-07	1,0	710	1300	550		17,7
-08	1,5	800	1450	820	538	33,7
-09	1,5	1000	1800	970		48,3
-10	1,5	1250	2250	1055	638	71,6

Umbrellas round, as a rule, are installed on exhaust shafts from exhaust fans. D0 - ventilation shaft diameter.

Umbrellas installed on ventilation shafts with natural and mechanical motivation in order to protect the shafts from atmospheric precipitation.
.The choice of the type of umbrella is made in accordance with the outer size of the mouth of the shaft, adopted in the project.
.All connecting dimensions correspond to the normalized range of air ducts of the plant, and the connecting dimensions of the units for the passage of ventilation exhaust shafts through the building coverings according to the series standard designs 5.904.
.All ways of connecting to air ducts are also normalized in accordance with the technology of the plant.

D1AA TECHNICAL CHARACTERISTICS

UMBRELLAS

Designation

Dimensions, 1 mm

Weight, kg

UMBRELLA ROUND

ZK.00.000

Umbrellas rectangular

ZP.00.000

DEFLECTORS

deflector no.

Designation

Dimensions, mm

D 315.00.000

D 710.00.000

C2BA INSTRUCTIONS FOR USE Umbrellas are installed on exhaust ventilation shafts in systems with natural and mechanical motivation in order to protect the shafts from atmospheric precipitation. The standard size of the umbrella is taken according to the outer size of the mouth of the shaft. Deflectors are installed on exhaust shafts in systems natural ventilation to ensure air exchange due to thermal and wind pressure. Deflectors are numbered from 3 to 10 according to the outer diameter of the shaft, expressed in decimeters. The choice of the deflector number is made in accordance with the estimated amount of air. For effective operation, the deflector must be installed 1.5-2.0 m above the roof ridge.

ADDITIONAL DATA

The connecting dimensions of umbrellas and deflectors correspond to the standardized dimensions of air ducts according to SNiP 2.04.05-86 and the connecting dimensions of the nodes for the passage of exhaust ventilation shafts through the coatings industrial buildings according to standard documentation series 5.904-10. With the entry into force of the working drawings of the 5.904-51 series, the working drawings of the standard designs of the 1.494-32 series are canceled.

B7EA COMPOSITION OF PROJECT DOCUMENTATION

Issue I. Working drawings. The volume of project materials reduced to A4 format, 66 formats.

• Series 1.073.9-2.00 Issue 1 Typical building structures, products and assemblies. Complex systems Knauf. Cladding element-by-element assembly of gypsum boards for building envelopes for residential, public and industrial buildings. Issue 1. Facings. Working drawings
• Series 1.031.9-2.00 Issue 1 Typical building structures, products and assemblies. Partitions of the "Knauf" system of element-by-element assembly from plasterboard sheets on metal and wooden frames for residential, public and industrial buildings. Issue 1. Partitions. Working drawings
• VNiR B3-3 Collection of departmental norms and prices for construction, installation and repair and construction work. Collection B3. Construction of subways, tunnels and underground structures for special purposes. Issue 3. Installation and dismantling of mining equipment in underground conditions
• VNiR B3-10 Collection of departmental norms and prices for construction, installation and repair and construction work. Collection B3. Construction of subways, tunnels and underground structures for special purposes. Issue 10. Installation and dismantling of auxiliary equipment in underground conditions
• Temporary instructions Temporary instructions on the composition, implementation rules, acquisition and execution of project documentation for standard building structures, products and assemblies
• Recommendations Guidelines for the reconstruction and modernization of engineering equipment of residential buildings of the first mass series

All documents presented in the catalog are not their official publication and are for informational purposes only. Electronic copies of these documents can be distributed without any restrictions. You can post information from this site on any other site.

the USSR	Construction catalog part 3 TYPICAL DOCUMENTATION for structures, products and components of buildings and structures	Products and nodes engineering equipment Series 5.904-51 Release 1
CITP
September 1989	umbrellas and deflectors ventilation systems	On 2 sheets on 3 pages

D1AA TECHNICAL CHARACTERISTICS

UMBRELLAS

Designation	Rice.	Dimensions, 1 mm							Weight, kg
		D 0					B 1	B 2
UMBRELLA ROUND
ZK.00.000
									2,85
									10,1
			1130						14,0
			1300						17,7
			1450						33,7
		1000	1800						48,3
		1250	2250	1055					71,6
Umbrellas rectangular
ZP.00.000
									12,0
						1440			31,5
					1000				58,6
								1440	27,0
						1440	1000	1800	53,5

DEFLECTORS

deflector no.	Designation	Dimensions, mm			Weight
			D 1
	D 315.00.000
					16,7
					31,8
			1190		46,5
	D 710.00.000		1320	1027	74,85
			1530	1285	104,27
			1750	1542	139,6
		1000	2000	1764	178,5

C2BA INSTRUCTIONS FOR USE

Umbrellas are installed on exhaust ventilation shafts in systems with natural and mechanical motivation in order to protect the shafts from atmospheric precipitation.

The standard size of the umbrella is taken according to the outer size of the mouth of the shaft.

Deflectors are installed on exhaust shafts in natural ventilation systems to ensure air exchange due to thermal and wind pressure.

Deflectors are numbered from 3 to 10 according to the outer diameter of the shaft, expressed in decimeters. The choice of the deflector number is made in accordance with the estimated amount of air. For effective operation, the deflector must be installed 1.5-2.0 m above the roof ridge.

ADDITIONAL DATA

The connecting dimensions of umbrellas and deflectors correspond to the normalized dimensions of air ducts according to SNiP 2.04.05-86 and the connecting dimensions of the nodes for the passage of exhaust ventilation shafts through the coatings of industrial buildings according to the standard documentation of the 5.904-10 series.

With the entry into force of the working drawings of the 5.904-51 series, the working drawings of the standard designs of the 1.494-32 series are canceled.

B7EA COMPOSITION OF PROJECT DOCUMENTATION

Release I . Working drawings.

The volume of project materials reduced to A4 format, 66 formats.

	TsNIIPROMZDANII 127238, Moscow, I-238, Dmitrov highway, 46
Q7 FOR APPROVAL	Approved by the Main Directorate of Design Organization Gosstroy of the USSR. Minutes No. 5 dated 26.01.1989 Put into effect by order of the Central Research Institute of Industrial Buildings No. 50 dated 04/24/1989 from 09/01/1989 Validity 1993
B7KA SUPPLIER	Tbilisi branch of CITP. 380053. Tbilisi, Avchala highway, 86-a.