How to make an even hole in the skin. A neat hole in the belt with improvised means. How to make your own belt punch

Both men and women are familiar with the problem when, when changing waist sizes, their favorite leather belt categorically refuses to fasten on the holes provided by the manufacturer. Naturally, in such a situation, people will immediately begin to make new holes at home and, as a rule, with improvised means.

Freshly made holes at home can significantly spoil appearance belt - if you do not know how to punch them correctly. Therefore, it is important to follow a few recommendations for the correct and accurate execution of belt holes.

A hammer will help you

First of all, attach the belt to your waist and mark the desired location of the new hole with a marker or pen. Then put the belt on wooden surface face up, put a sharp nail to the mark and hit its head several times with a hammer. Hit until the leg of the nail passes through the entire thickness of the belt.

Remember that the new hole must be located at the same distance from the other holes and be strictly parallel to them. Violation of this rule is fraught with damage to the entire product.

Be sure to lubricate the pierced hole with an ear plug. cotton swab and colorless shoe polish, thereby fixing the edges of the new hole.

If you are going to make a hole not in a leather, but in a riveted belt, insert another rivet into the new hole with a knife. Smooth the edges of the installed rivet with a hammer - so the altered belt will retain its original appearance.

We work with an awl

Make a mark on the intended location of the future hole. Lay the belt face down on a flat wooden surface, hold the sections near the mark with your fingers, and poke it vertically with an awl or a thick, sharp needle.

The wooden surface should be hard enough, but at the same time it should not prevent the awl or needle from piercing the belt through. Choose a comfortable and stable surface

After making a hole, take sharp nail scissors and expand the new hole with them. The width should be slightly narrower than the diameter of the belt tongue, as the hole will widen fairly quickly with use. To prevent the tongue from pulling the material behind it when passing through a new hole, bend the belt alternately in all directions so that the hole is located on its fold, and carefully trim the edges of the hole with very sharp tweezers.

If the belt is synthetic, carefully melt the edges of the new hole to help prevent peeling of the outer and inner layers of the material.

The main thing is accuracy, accuracy and accuracy again. But, if you are afraid that you will not have enough strength or skill, you can turn to a sewing or shoe shop for help. This measure will help to avoid damage to an expensive product.

How to make a hole in the belt yourself? Inaccurate work in this case can completely spoil the appearance of the product. Therefore, before proceeding with the implementation of the task, it is necessary to figure out how to properly punch a hole, what tools will be required for this. Next, consider a few recommendations that will help you figure out how to make a hole in the belt.

The use of a special punch

How to make a hole in the belt as accurate as possible? This will help. You can buy such a device relatively inexpensively at any point of sale. In order not to be mistaken with the diameter of the punch, when going to buy it, you need to take the belt with you. If you need to make holes in several belts, it is worth purchasing a tool with removable tips of various sizes.

In preparation for work, it is necessary to mark the plane of the belt by measuring the distance between the factory holes with a ruler. Then you should set aside the same segment on the plane and mark the location of the future hole.

Before using a leather puncher, it is necessary to fix the belt in such a way that its plane is in a taut state. Then it is enough to attach the tip of the punch to the intended area and squeeze its handles strongly. It is necessary to relax the hole punch for the skin as soon as its elements completely sew through the material.

Nails and hammer

How to make a hole in a leather belt? Most simple solution here looks like a breakout nail holes. The main thing is to initially determine the location of the future hole by taking the appropriate measurements. To make notes in the right places, just use ballpoint pen or a marker.

The work is performed in the following sequence:

• a suitable nail is selected, the diameter of which should approximately correspond to the dimensions of the factory holes on the product;
• the belt is located on a flat plank surface;
• the tip of the nail is set to the previously planned point;
• several accented blows are performed on the nail cap until its core completely sews through the belt;
• the nail is rotated several times in the thickness of the leather product, after which it is carefully pulled out with the help of pliers.

At the end of the work, it is desirable to treat the edges of the resulting hole with a neutral shoe cream. In this way, uneven edges of the material at the point of breakdown can be smoothed out.

Electric drill

When thinking about how to make a hole in a belt, it is worth considering the option of using an electric drill. With care, it can be used to make fairly even, neat holes.

To begin with, it is recommended to fix the belt by pressing down on its ends with a weighty load. In this case, the area to be treated should be located on a flat, hard surface, such as a wooden block.

To decide on optimal size drills, it is enough to manually insert several rods of individual diameters into the existing holes on the belt. It is recommended to stop on a drill that will fit tightly enough into the hole.

How to make a neat hole in a belt with a drill? To do this, you must first make a slight indentation at the intended point, using the tip sharp knife. As a result, the drill will not jump to the sides during the work.

Starting to make a hole, it is necessary to make short-term starts of the drill mechanism. In this way, the risk of making a sloppy hole can be minimized.

shoe awl

To cope with the task with shoe awl, first you need to mark the plane of the belt. Then you should place the product on a sufficiently hard plane, which at the same time can pierce the tip of the tool. You can lay the belt on compacted soil or a piece of foam.

Next, make a hole in the belt with the tip of an awl. If necessary, expand the diameter of the hole with any suitable metal rod. Pieces of material that formed on the inside of the product after breaking through can be carefully cut with nail scissors.

1. When trying to find a solution to how to make a hole in a belt, you should not resort to using the usual kitchen knife or scissors. Using such blades will not allow you to create neat holes.
2. Piercing thick rough skin may be enough challenging task. Therefore, when using a hole puncher, you may have to use the help of a partner.
3. The use of available tools, such as a hammer and nails, an awl or a drill, will not require additional costs. However, exploitation special tool designed for such work will save not only time, but also reduce the risk of accidental injury.
4. Before you start punching a hole in a leather product in one way or another, it may be worthwhile to pre-practice using a piece of old unnecessary material.

Summing up

So we figured out how to make a hole in the belt. The solutions indicated in the presented material will not force you to seek help from the workshop. The main thing is to do the work slowly and as carefully as possible so as not to spoil the product.

Choosing a belt shopping malls, stores and Internet sites, you can substitute that different belt manufacturers always make a certain number of holes. In this situation, you can ask the seller to make these holes, but sometimes it is better to make them yourself, having previously measured right amount holes and the distance between them, specifically for your waist.

How to quickly make additional holes in the belt?

First of all, try on the belt with your favorite pants and mark where you think the hole should be. The belt should tighten the belt in the same way as other belts.

Look at how far apart the holes made at the factory are. Our hole should be at a standard distance from the others. The marked place will only help.

It happens that the existing holes on the belt seem to be enough, but you would like to make another one in the middle. In this case, it is not necessary to take care that it is exactly between the other two. You also do not need to make other holes that will create a uniform chain on the belt. It is enough that the hole made is neat.

Make a washable mark where the hole will be made. Take an awl or a thick, sharp needle. Lay the strap face up on a flat surface. The selected surface should allow the belt to be pierced through, but at the same time be hard enough. A spring mattress will do.

Holding the belt with your fingers on both sides, pierce the belt. The needle enters strictly vertically. Now you will need nail scissors with thin sharp ends or a clerical knife. Using a knife or scissors, carefully expand the hole to the width through which the belt tongue will pass.

The main problem with homemade holes is that when the tongue passes through the hole from the bottom up, it pulls the material along with it. We need to make the hole have a conical shape. To do this, fold the belt in half so that the hole is on the fold itself. Trim the edges carefully. It is necessary to bend the belt along, then across, then in different directions obliquely.

Your tool must be very sharp so that you can accurately cut off very small pieces of material. Periodically check the width of the resulting hole. It is very easy to get carried away and cut off the excess.

The hole is made a little smaller than necessary for the free passage of the tongue. It will develop quickly. No leather strap further action do not need to do. Hole in belt synthetic material need to melt around the edges. So you prevent peeling of the outer and inner decorative layers of the material.

Heat the awl or needle on the sole of the iron, with which the hole was first made. The temperature of the iron is about 200 degrees. Carefully run along the edges, as if sealing them. The needle cools quickly, so you won't be able to melt the edges too much. But you do not need to press the needle, especially at the first moment after removing it from the iron.

In the described way, you will make a hole in the belt that will last a long time and will not differ in any way from others already on it.

Belt problems are equally familiar to both women and men. We are talking about this inconvenience: the missing holes on the canvas. The belt can become large due to a sharp change in the circumference of the waist or hips (depending on how long the belt is and what you wear it under). In such cases, the holes provided by the manufacturer are simply not enough. Do not be discouraged, you can make the necessary holes yourself, no worse than the existing ones. Moreover, this does not require special tools.

How to make an additional hole in the belt yourself

The usual puncture of a leather product can ruin its appearance. But there are several ways how to do it correctly and efficiently.

Hammer and nails

Before you start picking holes, determine their exact location. To do this, gird yourself with the product and mark the areas where new holes are needed. Notes can be made with a marker or other stationery writing object.

Place the belt on a wooden surface (no need to use a varnished table, take a piece of board). Now drive the nail into the skin. The diameter of the nail should approximately match the factory holes on the belt. Hammer a nail with front side product until it passes through the entire thickness of the skin.

Recommendation: Be sure to maintain proportions in the distance between the holes. New holes should be equidistant from each other and from the old grooves for the fastener tongue. So you do not harm the external integrity of the product.

After the hole is made, it must be treated with a colorless cream for leather shoes. This will fix the fresh edges and hide the contrast between the old and new hole. Process carefully with a cotton swab.

In the same way, you can punch holes in a riveted belt. Only here, in addition, insert a rivet into the hole. The same hammer will help to fix the metal.

shoe awl

First we apply the markup (see how to do this above). Then lay the belt face up again on a flat wooden surface. Hold the sheet near the puncture site and carefully insert an awl (you can use a thick gypsy needle) into the skin.

As for the wood you are working on, it should not be very hard, this can prevent the belt from piercing through.

Next, you need to expand the resulting hole. To do this, we take manicure scissors with pointed ends and clear the passage with them. Do not make the hole very large, its normal diameter is slightly less than the width of the fastener tongue. During the operation of the product, the skin will stretch, and the hole will become normal. Treat the hole so that there are no pieces of material left: bend the belt at the hole, first in one direction, then in the other (to release the remnants of the skin), and then carefully cut the tatters with scissors or sharp tweezers.

Product from artificial materials can also be provided with new holes. In this case, the edges are treated with fire or a hot object. It is necessary to make sure that there is no peeling of the internal and external materials belts.

Whatever method you use, do it carefully and carefully. If you don’t trust yourself or you didn’t have it at hand the right tools, you can always ask for help in a shoe or sewing workshop. They will do it quickly, correctly and will not spoil the product.