GOST 7415-86

Hydroisol- coverless biostable roll material, obtained by impregnating asbestos paper with petroleum bitumen, is manufactured in accordance with GOST 7415-86.

Hydroisol is intended for waterproofing underground and other structures, devices roll roofing and anti-corrosion coatings pipelines.

The waterproofing must be applied in accordance with the regulatory and technical documentation for the design and production of waterproofing works.

Hydroisol refers to combustible materials.

Depending on the purpose and scope of application, hydroisol is divided into two grades:

GI-G- Waterproofing waterproofing. Designed for waterproofing underground structures subway, underground
parts of high-rise and multi-storey buildings, anticorrosive protection of metal pipelines, except for heat pipelines, with gluing of its web with hot bituminous mastic.

GI-K- Roofing waterproofing, designed for waterproofing flat roofs with gluing his canvas with hot bituminous mastic.

Hydroisol is produced in rolls with a web width of (950 ± 5) mm.

Specifications

total area waterproofing sheets in a roll should be (20 + 0.5) m 2.

The symbol of hydroisol in the technical documentation and when ordering should consist of the name of the material, its brand and the designation of this standard.

Example symbol hydroisol for waterproofing underground structures of the subway brand GI-G:

Hydroisol GI-G GOST 7415-86

Table 1. Physical and mechanical parameters of "hydroisol" (GOST 7415-86)

The asbestos base of the hydroisol must be evenly impregnated throughout the entire thickness of the sheet. In the tear, the waterproofing should be black or black with a brown tint without light layers of unimpregnated base and foreign inclusions.

The surface of the hydroisol should be matte and should not have irregularities and tubercles with a height of more than 1 mm. Separate shiny bituminous spots are allowed on the surface of the hydroisol, sprinkled with fine sand, which prevents the sheet from sticking together in a roll. The grain size of fine-grained quartz sand for sprinkling hydroisol should not exceed 0.63 mm.

The waterproof sheet should not have holes, tears, folds. On the edges (edges) of the waterproofing sheet, more than two tears 10-30 mm long are not allowed in one roll, tears with a length of St. 30 mm are not allowed, and tears up to 10 mm long are not standardized. Rolls of hydroisol should be rolled out without cracking at a temperature of 268K (-5 °C). The waterproof sheet must be wound into a roll. The roll must have even ends.

More than 5% of composite rolls are not allowed in a batch of hydroisol, and more than two canvases in one composite roll, the shortest of which should not be less than 3 m. Hydroisol rolls, including a joint of glued asbestos paper, are not considered composite. In a batch of waterproofing of the highest quality category, there should be no composite rolls and rolls with glued asbestos paper.

HYDROISOL

TECHNICALCONDITIONS

GOST 7415-86

STANDARDS PUBLISHING HOUSE

Moscow

STATE STANDARD OF THE UNION OF THE SSR

Decree of the State Committee of the USSR for Construction Affairs of December 30, 1985 No. 285 established the deadline for the introduction

from 01.01.87

1A. APPLICATION AREA

This standard applies to hydroisol - a non-coated roll material obtained by impregnating asbestos paper with petroleum bitumen.

Gidroizol is intended for waterproofing underground and other structures, roll roofing and anti-corrosion coatings of pipelines.

1B. NORMATIVE REFERENCES

GOST 12.3.009-76 SSBT. Loading and unloading works. General requirements security.

GOST 12.4.011-89 SSBT. Means of protection for workers. General requirements and classification.

GOST 12.4.013-85 SSBT. Goggles. General specifications.

GOST 12.4.041-89 SSBT. Facilities personal protection respiratory organs filtering. General technical requirements.

GOST 2678-94 Roll roofing and waterproofing materials. Test methods.

GOST 7377-85 Corrugating paper. Specifications.

GOST 8273-75 Wrapping paper. Specifications.

GOST 9548-74 Roofing oil bitumen. Specifications.

GOST 14192-96 Marking of goods.

GOST 19433-88 Dangerous goods. Classification and marking.

GOST 22245-90 Viscous oil road bitumen. Specifications.

GOST 23779-95 Asbestos paper. Specifications.

GOST 30244-94 Construction materials. Test methods for combustibility.

GOST 30402-96 Construction materials. Flammability test method.

GOST 30444-97 Construction materials. Flame propagation test method.

GOST 30547-97 Roll roofing and waterproofing materials. General specifications.

(Revised edition, Rev. No. 1).

1. MAIN PARAMETERS AND DIMENSIONS

1.1. Depending on the purpose and scope, hydroisol is divided into two grades indicated in Table. one.

1.2. Hydroisol is produced in rolls with a web width of (9505) mm.

The total area of ​​\u200b\u200bthe waterproofing sheet in a roll should be (200.5) m 2.

It is allowed, in agreement with the consumer, to produce rolls of other widths and areas.

The reference weight of the roll is given in Appendix A.

Table 1

(Revised edition, Rev. No. 1).

1.3. The symbol of hydroisol in the technical documentation and when ordering should consist of the name of the material, its brand and the designation of this standard.

An example of a symbol for a hydroisol for waterproofing underground structures of the subway brand GI-G:

Hydroisol GI-G GOST 7415-86

2. TECHNICAL REQUIREMENTS

2.1. The hydroisol must be manufactured in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner.

2.2. Qualitative indicators of hydroisol should correspond to those indicated in table. 2.

table 2

2.3. Hydroisol brand GI-G can be certified for the highest quality category.

2.3.1-2.3.4. (Deleted, Rev. No. 1).

2.4. The asbestos base of the hydroisol must be evenly impregnated throughout the entire thickness of the sheet. In the tear, the waterproofing should be black or black with a brown tint without light layers of unimpregnated base and foreign inclusions.

2.5. Requirements to appearance waterproofing, sheet edges, adhesion, evenness of the ends, the size of the protrusions at the ends of the roll, the number of composite rolls and sheets in a roll - according to GOST 30547 with the following addition:

The surface of the waterproofing must be matte. Allowed presence greasy spots that do not cause sticking of the web in a roll.

(Revised edition, Rev. No. 1).

2.6-2.9.(Deleted, Rev. No. 1).

2.10. Requirements for raw materials and materials - according to GOST 30547. For the manufacture of waterproofing, the raw materials and materials listed in Appendix B are recommended.

(Revised edition, Rev. No. 1).

2.11. The waterproofing must be waterproof. When tested hydroisol GI-K at a pressure of at least 0.001 MPa (0.01 kgf / cm 2) for at least 72 hours, and hydroisol GI-G at a pressure of at least 0.05 MPa (0.5 kgf / cm 2) for at least 15 minutes no signs of water penetration should appear on the surface of the sample.

2.12. The waterproofing must be flexible. When tested on a bar with a rounding radius of (25.0 ± 0.2) mm at a temperature not exceeding 5 ° C, cracks should not appear on the surface of the sample.

2.13. Packaging and labeling

2.13.1. Each roll of hydroisol must be wrapped across the entire width with paper, the weight of 1 m 2 of which must be at least 120 g, according to GOST 8273 or GOST 7377 or other paper of similar quality.

It is allowed to use other packaging materials, ensuring the safety of hydroisol during transportation and storage.

2.13.2. The marking of hydroisol should be carried out in accordance with GOST 30547. The label should indicate:

Name of the manufacturer or its trademark;

Name of the material and its brand;

The designation of this standard;

Lot number (or other batch designation accepted at the manufacturer) and date of manufacture;

Brief instructions for use.

The list of data on the label (stamp) can be supplemented or changed in agreement with the consumer of the product.

Transport marking - in accordance with GOST 14192 with the application of basic, additional and informational inscriptions.

(Revised edition, Rev. No. 1).

3. SAFETY AND ENVIRONMENTAL REQUIREMENTS

3.1. Hydroisol has the following fire hazard indicators:

Flammability group - G4 according to GOST 30244;

Flammability group - B3 according to GOST 30402;

Flame propagation group - RP4 according to GOST 30444.

3.2. According to the classification of GOST 19433, hydroisol does not belong to dangerous goods.

3.3. When working with waterproofing in the air working area it is possible to release asbestos-containing dust, the safety requirements for which are in accordance with GOST 23779.

3.4. Persons involved in work with hydroisol should be provided with overalls and personal protective equipment in accordance with GOST 12.4.011, for respiratory protection - with respirators in accordance with GOST 12.4.041, for skin protection - with mittens or gloves, for eye protection - with goggles in accordance with GOST 12.4.013.

3.5. The disposal of hydroisol waste generated during the manufacture, construction and repair of buildings and structures should be carried out in pits in compliance with measures to ensure that asbestos-containing dust is not carried by the wind at the time of unloading by wetting or transportation in paper or plastic bags, according to the current sanitary standards and rules.

3.6. In the event of a bitumen or hydroisol fire, the following fire extinguishing agents should be used: acid or foam fire extinguishers, asbestos cloth, felt mat, special powders, water with wetting.

3.7. During loading and unloading operations, safety requirements in accordance with GOST 12.3.009 must be observed.

(Revised edition, Rev. No. 1).

4. ACCEPTANCE RULES

4.1. The rules for acceptance of hydroisol are in accordance with GOST 30547. The batch size is set in an amount of no more than 1500 rolls.

4.2. Water resistance, water absorption, brittleness and softening temperatures of the coating composition should be determined at least once a month and when changing raw materials.

(Revised edition, Rev. No. 1).

5. TEST METHODS

Test methods - according to GOST 2678 with the following additions:

Tensile breaking strength is determined at the speed of movement of the movable grip (50±5) mm/min;

Flexibility by the number of double folds is determined on samples of hydroisol with a size of [(50x100) ± 1 mm]. Before testing, the specimens are kept in water for (15 ± 0.5) min at a temperature not exceeding 291 K (18 °C), after which the specimens are manually bent by 180°. Specimens are considered to have passed the test if, after the number of bends indicated in Table 2, no through cracks appear on them.

(Revised edition, Rev. No. 1).

6. STORAGE AND TRANSPORTATION

6.1., 6.2. (Deleted, Rev. No. 1).

6.3. Transportation of hydroisol rolls should be carried out in containers or packages installed in covered wagons or other closed vehicles.

It is allowed, with the consent of the consumer, to transport the hydroisol without containers or packages in a vertical position in no more than one row in height, while the hydroisol rolls must be protected from mechanical damage and contamination.

By agreement with the consumer, other methods of transportation are allowed to ensure the safety of the hydroisol.

(Revised edition, Rev. No. 1).

6.4. Loading into vehicles and transportation of hydroisol is carried out in accordance with the Rules for the carriage of goods in force for this type of transport.

(Revised edition, Rev. No. 1).

6.5. Rolls of hydroisol, sorted by brand, should be stored in a dry, closed room in a vertical position no more than two rows in height at a distance of at least 1 m from heating appliances. When storing rolls in containers, the number of their vertical rows is not limited and is determined by safety requirements.

6.6. The shelf life of hydroisol is 6 months from the date of manufacture.

At the end of the storage period, the hydroisol shall be checked for compliance with the requirements of this standard. In case of compliance, the hydroisol can be used for its intended purpose.

(Introduced additionally, Rev. No. 1).

7. MANUFACTURER WARRANTY

(Deleted, Rev. No. 1).

8. INSTRUCTIONS FOR USE

The hydroisol must be applied in accordance with the applicable regulations. building codes and rules

APPENDIX A

Reference

Reference weight of a roll of hydroisol

Deviation from the reference mass of the roll is not a rejection sign.

APPENDIX B

Raw materials and materials used for the manufacture of waterproofing

Oil roofing bitumen grade BNK 40/180 according to GOST 9548

Oil bitumen road stamps BND 60/90 or BND 40/60 according to GOST 22245

Asbestos paper grades BG-M or BG-K according to GOST 23779

Other raw materials and materials - according to normative documentation approved in the prescribed manner, in accordance with technological regulations for the production of waterproofing.

(Introduced additionally, Amendment No. 1).

HYDROISOL

TECHNICALCONDITIONS

GOST 7415-86

STANDARDS PUBLISHING HOUSE

Moscow

STATE STANDARD OF THE UNION OF THE SSR

Decree of the State Committee of the USSR for Construction Affairs of December 30, 1985 No. 285 established the deadline for the introduction

from 01.01.87

1A. APPLICATION AREA

This standard applies to hydroisol - a non-coated roll material obtained by impregnating asbestos paper with petroleum bitumen.

Gidroizol is intended for waterproofing underground and other structures, roll roofing and anti-corrosion coatings of pipelines.

1B. NORMATIVE REFERENCES

This standard makes reference to the following standards and specifications:

Name of hydroisol

Name and scope

Hydroisol waterproofing

Waterproofing of underground structures of the subway, the underground part of high-rise and multi-storey buildings, anti-corrosion protection of metal pipelines, except for heat pipelines, with gluing its cloth with hot bituminous mastic

Roofing waterproofing

Waterproofing of flat roofs with gluing of its sheet with hot bituminous mastic

(Revised edition, Rev. No. 1).

1.3. The symbol of hydroisol in the technical documentation and when ordering should consist of the name of the material, its brand and the designation of this standard.

Symbol examplehydroisol for waterproofing underground structures of the subway brand GI-G:

Hydroisol GI-G GOST 7415-86

2. TECHNICAL REQUIREMENTS

2.1. The hydroisol must be manufactured in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner.

2.2. Qualitative indicators of hydroisol should correspond to those indicated in table. .

table 2

2.3. Hydroisol brand GI-G can be certified for the highest quality category.

The waterproofing of the highest quality category must meet the following additional requirements.

2.3.1-2.3.4. (Deleted, Rev. No. 1).

2.4. The asbestos base of the hydroisol must be evenly impregnated throughout the entire thickness of the sheet. In the tear, the waterproofing should be black or black with a brown tint without light layers of unimpregnated base and foreign inclusions.

2.5. Requirements for the appearance of the waterproofing material, the edges of the sheet, stickiness, evenness of the ends, the size of the protrusions at the ends of the roll, the number of composite rolls and sheets in a roll - according to GOST 30547 with the following addition:

The surface of the waterproofing must be matte. The presence of greasy spots that do not cause sticking of the web in a roll is allowed.

(Revised edition, Rev. No. 1).

2.6-2.9.(Deleted, Rev. No. 1).

2.10. Requirements for raw materials and materials - according to GOST 30547. For the manufacture of waterproofing, the raw materials and materials listed in the appendix are recommended.

(Revised edition, Rev. No. 1).

2.11. The waterproofing must be waterproof. When testing hydroisol GI-K at a pressure of at least 0.001 MPa (0.01 kgf / cm 2) for at least 72 hours, and hydroisol GI-G at a pressure of at least 0.05 MPa (0.5 kgf / cm 2) for at least 15 min, no signs of water penetration should appear on the surface of the sample.

2.12. The waterproofing must be flexible. When tested on a beam with a rounding radius (25.0± 0.2) mm at a temperature not exceeding 5° C, cracks should not appear on the surface of the sample.

2.13. Packaging and labeling

2.13.1. Each roll of hydroisol must be wrapped across the entire width with paper, the weight of 1 m 2 of which must be at least 120 g, according to GOST 8273 or GOST 7377 or other paper of similar quality.

It is allowed to use other packaging materials that ensure the safety of the hydroisol during transportation and storage.

2.13.2. Hydroisol marking should be carried out in accordance with GOST 30547. The label must indicate:

- name of the manufacturer or its trademark;

- name of the material and its brand;

- designation of this standard;

- batch number (or other batch designation adopted by the manufacturer) and date of manufacture;

- brief instructions for use.

The list of data on the label (stamp) can be supplemented or changed in agreement with the consumer of the product.

Transport marking - in accordance with GOST 14192 with the application of basic, additional and informational inscriptions.

(Revised edition, Rev. No. 1).

3. SAFETY AND ENVIRONMENTAL REQUIREMENTS

3.1. Hydroisol has the following fire hazard indicators:

- combustibility group - G4 according to GOST 30244;

- flammability group - B3 according to GOST 30402;

- flame propagation group - RP4 according to GOST 30444.

3.2. According to the classification of GOST 19433, hydroisol does not belong to dangerous goods.

3.3. When working with a hydroisol, it is possible to release asbestos-containing dust into the air of the working area, the safety requirements for which are in accordance with GOST 23779.

3.4. Persons employed in work with hydroisol should be provided with overalls and personal protective equipment in accordance with GOST 12.4.011, for respiratory protection - with respirators in accordance with GOST 12.4.041, for skin protection - with mittens or gloves, for eye protection - with goggles in accordance with GOST 12.4.013.

3.5. The disposal of hydroisol waste generated during the manufacture, construction and repair of buildings and structures should be carried out in pits in compliance with measures to ensure that asbestos-containing dust is not carried by the wind at the time of unloading by wetting or transportation in paper or plastic bags, according to current sanitary norms and rules.

3.6. In the event of a bitumen or hydroisol fire, the following fire extinguishing agents should be used: acid or foam fire extinguishers, asbestos cloth, felt mat, special powders, water with wetting.

3.7. During loading and unloading operations, safety requirements in accordance with GOST 12.3.009 must be observed.

(Revised edition, Rev. No. 1).

4. ACCEPTANCE RULES

4.1. Rules for the acceptance of hydroisol - according to GOST 30547. The batch size is set in the amount of not more than 1500 rolls.

4.2. Water resistance, water absorption, brittleness and softening temperatures of the coating composition should be determined at least once a month and when changing raw materials.

(Revised edition, Rev. No. 1).

5. TEST METHODS

Test methods - according to GOST 2678 with the following additions:

The breaking force in tension is determined at the speed of movement of the movable grip (50± 5) mm/min;

Flexibility by the number of double folds is determined on hydroisol samples with a size[ (50x100) ± 1 mm ] . Before testing, the samples are kept in water for (15± 0.5) min at a temperature not exceeding 291 K (18° C), after which the samples are manually bent by 180° . The samples are considered to have passed the test if, after the number of bends indicated in the table, through cracks do not appear on them.

(Revised edition, Rev. No. 1).

6. STORAGE AND TRANSPORTATION

6.1., 6.2. (Deleted, Rev. No. 1).

6.3. Transportation of hydroisol rolls should be carried out in containers or packages installed in covered wagons or other closed vehicles.

It is allowed, with the consent of the consumer, to transport the hydroisol without containers or packages in a vertical position in no more than one row in height, while the hydroisol rolls must be protected from mechanical damage and contamination.

By agreement with the consumer, other methods of transportation are allowed to ensure the safety of the hydroisol.

(Revised edition, Rev. No. 1).

6.4. Loading into vehicles and transportation of hydroisol is carried out in accordance with the Rules for the carriage of goods in force for this type of transport.

(Revised edition, Rev. No. 1).

6.5. Rolls of hydroisol, sorted by brand, should be stored in a dry closed room in a vertical position no more than two rows in height at a distance of at least 1 m from heating devices. When storing rolls in containers, the number of their vertical rows is not limited and is determined by safety requirements.

6.6. The shelf life of hydroisol is 6 months from the date of manufacture.

At the end of the storage period, the hydroisol shall be checked for compliance with the requirements of this standard. In case of compliance, the hydroisol can be used for its intended purpose.

(Introduced additionally, Rev. No. 1).

7. MANUFACTURER WARRANTY

(Deleted, Rev. No. 1) .

8. INSTRUCTIONS FOR USE

The waterproofing must be applied in accordance with current building codes and regulations. GOST 22245

Asbestos paper grades BG-M or BG-K according to GOST 23779

Other raw materials and materials - according to the regulatory documentation approved in the prescribed manner, in accordance with the technological regulations for the production of hydroisol.

(Introduced additionally, Amendment No. 1).

All documents presented in the catalog are not their official publication and are for informational purposes only. Electronic copies of these documents can be distributed without any restrictions. You can post information from this site on any other site.

HYDROISOL

TECHNICALCONDITIONS

GOST 7415-86

STANDARDS PUBLISHING HOUSE

Moscow

STATE STANDARD OF THE UNION OF THE SSR

Decree of the State Committee of the USSR for Construction Affairs of December 30, 1985 No. 285 established the deadline for the introduction

from 01.01.87

1A. APPLICATION AREA

This standard applies to hydroisol - a non-coated roll material obtained by impregnating asbestos paper with petroleum bitumen.

Gidroizol is intended for waterproofing underground and other structures, roll roofing and anti-corrosion coatings of pipelines.

1B. NORMATIVE REFERENCES

This standard makes reference to the following standards and specifications:

Name of hydroisol

Name and scope

Hydroisol waterproofing

Waterproofing of underground structures of the subway, the underground part of high-rise and multi-storey buildings, anti-corrosion protection of metal pipelines, except for heat pipelines, with gluing its cloth with hot bituminous mastic

Roofing waterproofing

Waterproofing of flat roofs with gluing of its sheet with hot bituminous mastic

(Revised edition, Rev. No. 1).

1.3. The symbol of hydroisol in the technical documentation and when ordering should consist of the name of the material, its brand and the designation of this standard.

Symbol examplehydroisol for waterproofing underground structures of the subway brand GI-G:

Hydroisol GI-G GOST 7415-86

2. TECHNICAL REQUIREMENTS

2.1. The hydroisol must be manufactured in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner.

2.2. Qualitative indicators of hydroisol should correspond to those indicated in table. .

table 2

2.3. Hydroisol brand GI-G can be certified for the highest quality category.

The waterproofing of the highest quality category must meet the following additional requirements.

2.3.1-2.3.4. (Deleted, Rev. No. 1).

2.4. The asbestos base of the hydroisol must be evenly impregnated throughout the entire thickness of the sheet. In the tear, the waterproofing should be black or black with a brown tint without light layers of unimpregnated base and foreign inclusions.

2.5. Requirements for the appearance of the waterproofing material, the edges of the sheet, stickiness, evenness of the ends, the size of the protrusions at the ends of the roll, the number of composite rolls and sheets in a roll - according to GOST 30547 with the following addition:

The surface of the waterproofing must be matte. The presence of greasy spots that do not cause sticking of the web in a roll is allowed.

(Revised edition, Rev. No. 1).

2.6-2.9.(Deleted, Rev. No. 1).

2.10. Requirements for raw materials and materials - according to GOST 30547. For the manufacture of waterproofing, the raw materials and materials listed in the appendix are recommended.

(Revised edition, Rev. No. 1).

2.11. The waterproofing must be waterproof. When testing hydroisol GI-K at a pressure of at least 0.001 MPa (0.01 kgf / cm 2) for at least 72 hours, and hydroisol GI-G at a pressure of at least 0.05 MPa (0.5 kgf / cm 2) for at least 15 min, no signs of water penetration should appear on the surface of the sample.

2.12. The waterproofing must be flexible. When tested on a beam with a rounding radius (25.0± 0.2) mm at a temperature not exceeding 5° C, cracks should not appear on the surface of the sample.

2.13. Packaging and labeling

2.13.1. Each roll of hydroisol must be wrapped across the entire width with paper, the weight of 1 m 2 of which must be at least 120 g, according to GOST 8273 or GOST 7377 or other paper of similar quality.

It is allowed to use other packaging materials that ensure the safety of the hydroisol during transportation and storage.

2.13.2. Hydroisol marking should be carried out in accordance with GOST 30547. The label must indicate:

- name of the manufacturer or its trademark;

- name of the material and its brand;

- designation of this standard;

- batch number (or other batch designation adopted by the manufacturer) and date of manufacture;

- brief instructions for use.

The list of data on the label (stamp) can be supplemented or changed in agreement with the consumer of the product.

Transport marking - in accordance with GOST 14192 with the application of basic, additional and informational inscriptions.

(Revised edition, Rev. No. 1).

3. SAFETY AND ENVIRONMENTAL REQUIREMENTS

3.1. Hydroisol has the following fire hazard indicators:

- combustibility group - G4 according to GOST 30244;

- flammability group - B3 according to GOST 30402;

- flame propagation group - RP4 according to GOST 30444.

3.2. According to the classification of GOST 19433, hydroisol does not belong to dangerous goods.

3.3. When working with a hydroisol, it is possible to release asbestos-containing dust into the air of the working area, the safety requirements for which are in accordance with GOST 23779.

3.4. Persons employed in work with hydroisol should be provided with overalls and personal protective equipment in accordance with GOST 12.4.011, for respiratory protection - with respirators in accordance with GOST 12.4.041, for skin protection - with mittens or gloves, for eye protection - with goggles in accordance with GOST 12.4.013.

3.5. The disposal of hydroisol waste generated during the manufacture, construction and repair of buildings and structures should be carried out in pits in compliance with measures to ensure that asbestos-containing dust is not carried by the wind at the time of unloading by wetting or transportation in paper or plastic bags, according to current sanitary norms and rules.

3.6. In the event of a bitumen or hydroisol fire, the following fire extinguishing agents should be used: acid or foam fire extinguishers, asbestos cloth, felt mat, special powders, water with wetting.

3.7. During loading and unloading operations, safety requirements in accordance with GOST 12.3.009 must be observed.

(Revised edition, Rev. No. 1).

4. ACCEPTANCE RULES

4.1. Rules for the acceptance of hydroisol - according to GOST 30547. The batch size is set in the amount of not more than 1500 rolls.

4.2. Water resistance, water absorption, brittleness and softening temperatures of the coating composition should be determined at least once a month and when changing raw materials.

(Revised edition, Rev. No. 1).

5. TEST METHODS

Test methods - according to GOST 2678 with the following additions:

The breaking force in tension is determined at the speed of movement of the movable grip (50± 5) mm/min;

Flexibility by the number of double folds is determined on hydroisol samples with a size[ (50x100) ± 1 mm ] . Before testing, the samples are kept in water for (15± 0.5) min at a temperature not exceeding 291 K (18° C), after which the samples are manually bent by 180° . The samples are considered to have passed the test if, after the number of bends indicated in the table, through cracks do not appear on them.

(Revised edition, Rev. No. 1).

6. STORAGE AND TRANSPORTATION

6.1., 6.2. (Deleted, Rev. No. 1).

6.3. Transportation of hydroisol rolls should be carried out in containers or packages installed in covered wagons or other closed vehicles.

It is allowed, with the consent of the consumer, to transport the hydroisol without containers or packages in a vertical position in no more than one row in height, while the hydroisol rolls must be protected from mechanical damage and contamination.

By agreement with the consumer, other methods of transportation are allowed to ensure the safety of the hydroisol.

(Revised edition, Rev. No. 1).

6.4. Loading into vehicles and transportation of hydroisol is carried out in accordance with the Rules for the carriage of goods in force for this type of transport.

(Revised edition, Rev. No. 1).

6.5. Rolls of hydroisol, sorted by brand, should be stored in a dry closed room in a vertical position no more than two rows in height at a distance of at least 1 m from heating devices. When storing rolls in containers, the number of their vertical rows is not limited and is determined by safety requirements.

6.6. The shelf life of hydroisol is 6 months from the date of manufacture.

At the end of the storage period, the hydroisol shall be checked for compliance with the requirements of this standard. In case of compliance, the hydroisol can be used for its intended purpose.

(Introduced additionally, Rev. No. 1).

7. MANUFACTURER WARRANTY

(Deleted, Rev. No. 1) .

8. INSTRUCTIONS FOR USE

The waterproofing must be applied in accordance with current building codes and regulations.