Step-by-step instructions on how to start a chainsaw in the summer or winter season. How to start a chainsaw of various brands

Many people buy chainsaws for the first time, having no experience with this tool. Despite this, in order to learn how to work with an instrument, there is no need to take special courses. After the purchase, there is a great desire to quickly test the tool in operation. To do this, be sure to first read the instruction manual for the tool, as well as safety precautions when working with a chainsaw. In the material, we will consider how to properly start a chainsaw, as well as work with it.

Every master who has a chainsaw should know how to start it correctly. Initially, it should be noted that in order to start the tool, it must be refueled. For this, not just gasoline is used, but a gasoline-oil mixture.

It is important to know! Pure gasoline for the operation of chainsaws cannot be refueled. It is necessary to fill only a mixture of gasoline with the appropriate oil for two-stroke engines.

First you need to figure out how to properly prepare the gasoline-oil mixture. These proportions are naturally indicated in the instructions, but since few people read them, this issue should be considered in detail.

AI92 and higher gasoline is used as fuel. You will also need to use the appropriate oil, which can be purchased at the same place where the chainsaw was bought. The proportion of gasoline and oil is 1 to 50, after mixing which must be thoroughly mixed. In this case, the mixture should be prepared in separate container (plastic bottle), since it is not only convenient to store the prepared fuel mixture in it, but also convenient to fill the tool tank through the small diameter of the gas tank hatch.

The prepared mixture should be poured into the fuel tank, the lid of which is indicated as an image of a gas station. This is very important, since chainsaws have two similar tanks. The second tank is intended for filling oil, which is consumed to lubricate the bar and chain during the operation of the tool.

It is important to know! After refueling the gas tank, do not rush to start the tool. Be sure to also add oil to the oil tank to prevent overheating of the chain, which could result in damage to the chain.

As an oil for lubricating the chain, it is recommended to use special branded or engine oil for a car, but in no case should it be used. If you see how your neighbor fills mining in a chainsaw, then you should not repeat his mistakes, as this significantly reduces the life of not only the chain, but also the tool itself.

Always check the oil level and fuel mixture in tanks, but it is recommended to refuel according to the following scheme:

• The fuel-oil mixture is filled into the tank until it is full.
• At the same time, chain oil is also filled to the full.
• The consumption of oil and fuel mixture is approximately the same, so both tanks are recommended to be filled at the same time.

How to start a chainsaw: launch features

Once the tool is ready to run, you can proceed. The process of starting a chainsaw is as follows:

Having launched a chainsaw, you can begin to work on sawing wood.

It is important to know! The material describes the process of launching the tool, after which you can start working with it. Do not forget that if you bought a new chainsaw, then it should initially be run in.

How to operate a chainsaw

Working with a chainsaw is one of the most dangerous, so it is very important to control the position of the tire as far away from you as possible. Each subsequent action must be deliberate, otherwise the consequences in the form of serious injuries cannot be avoided. If you have to work with a chainsaw, then you should know the following features:

1. It is required to work only in appropriate overalls: a protective helmet, headphones, a suit, gloves and shoes. This will increase the security of the master several times.
2. You need to hold the tool exclusively with two hands, and take the appropriate position with your feet in the form of a reliable stop. Working while standing in an uncomfortable position is strictly prohibited.
3. Lean the tool against the wood with a moving chain at medium speed.
4. Sawing with the tip of the tire should be done with extreme caution, as the likelihood of kickback is quite high.
5. When working, remove from the sawing area all unnecessary objects that can cause imbalance.
6. If you are tired, then you need to muffle the instrument, allowing not only yourself, but also him to rest.
7. When working, the legs should be widely separated to the sides, and the back should be straight.
8. You can cut wood not only with the bottom of the tire, but also with the top, only it is important to know that the chain will lead in the appropriate direction.
9. When moving with a chainsaw to another place, the tool should be turned off or put on the handbrake.

The above features are also suitable for working with an electric saw. Work is best done in tandem with a partner who can not only insure, but also replace you when you get tired. After all, working with such a tool is not easy, because in addition to physical strength, quick wit is also required. Observing the above rules for working with a chainsaw, all types of manipulations performed will have a successful conclusion.

Chainsaw Care

Another important condition when working with the tool is to ensure proper care of it. After completing the work, you should not leave the chainsaw at the workplace until the next time. It is necessary to clean it of sawdust and debris, periodically check the chain tension, as well as the fullness of the gas tank and oil tank. It is also important to watch for air filter clogging.

Not recommended long time store the chainsaw with fuel filled, so it is better to drain it. It is necessary to replace the chain, bar and drive sprocket in a timely manner, as these are elements that wear out quickly.

In conclusion, it is important to note that over time, the chain tends to stretch, which results in the fact that it cannot be tensioned. If you observe such a property, then it is not recommended to continue to operate the tool until cutting tool will not tear or come off the tire at all. If a person is not confident in his abilities, then it is better not to take on sawing trees of large diameter.

How to start a chainsaw

The question of how to start a chainsaw can be divided into two parts:

1. Winding by annotation
2. What to do if it won't start

The information from the first part will be useful for those who have lost the annotation, or for those whose annotation is not very informative.

The 2nd part will tell you what to do if you did everything right according to the annotation, but the chainsaw still does not start. It will also be useful for those who have a chainsaw that does not start well.

1. Start the chainsaw according to the instructions

Different chainsaws can be wound in different ways. Let's analyze two more favorite mechanisms that are used in order to start a chainsaw, available today. For example, take the Stihl MS 180 and Echo CS-352ES chainsaws. To properly start a Stihl, Husqvarna or other brand chainsaw, you must first read the instructions and follow its points. If you have a chainsaw of another brand, then just try to start by analogy, because most likely you have the same or a similar mechanism.

Before starting the description of the winding process, it is good to see that some chainsaws have an annotation that says that before starting the chainsaw, it is necessary to turn on the critical stop brake. Like it's safer. But with a fixed brake, it is more difficult to start a chainsaw, so it is better to unlock it. If everything is done according to reason, then the chainsaw will not do anything for you during start-up. If you are afraid that without fixing the brake, the chainsaw, when you try to start it, will be able to harm you, then it’s better not to take on this tool at all.

So let's start with the Stihl MS 180.

• The first thing to do before starting this chainsaw is to move the damper adjustment lever to the lower position (Fig. 1). Note that this lever only moves to the bottom of the chainsaw when the throttle button is pressed. Therefore, we hold down the gas button and move the lever down. Thus, we close the damper in the carburetor and fix the gas at the chainsaw in the pressed position.

Now we will analyze the 2nd 2nd mechanism, which allows you to start a chainsaw.

• At first, before trying to start, turn on the ignition by moving the switch or chainsaw switch to the appropriate position (Fig. 5).

How to start a Husqvarna chainsaw correctly

How to run Husqvarna chainsaw. How to start a chainsaw - a couple of the most popular. Recommendations for starting a chainsaw. Buy online www.

Husqvarna chainsaw Husqvarna 236 video review how to start a chainsaw

Chainsaw Husqvarna(Husqvarna) 236 - performance review, first start of a cold engine. We are Vkontakte: .

Rice. 5

2. Why won't the chainsaw start?

If you did everything according to the instructions, but the chainsaw still does not start, then something is wrong with it. This may be due to several of the most common reasons: no spark; fuel is not supplied; clogged air filter. So, below we offer a procedure that will help identify the reason why the chainsaw does not start.

What to do if your chainsaw does not start

Read also

The first thing I would like to note, if your chainsaw does not start, do not turn any screws on the carburetor. You need to start the saw on the right mixture of Husqvarna 142 saws. Sometimes. If you are not a specialist, you still won’t be able to set something up on your own and you won’t be able to start a chainsaw.

Perform the following actions necessary to start the chainsaw in the order indicated, starting to do the action under the next number only if the previous one did not help.

1. Try to start by just leaving the chainsaw alone for 5-10 minutes. Perhaps during the winding she had a candle filled - it happens. Then try to start again according to the instructions.
2. Remove the housing cover on the chainsaw, remove the air filter and try to start without it. If the filter is dirty, it should be washed in soapy water and dried or replaced with a new one.
3. Remove the spark plug from the chainsaw. Check for spark. Husqvarna 236 chainsaw malfunctions. Recently acquired husqvarna chainsaw 236, at the moment it is not clear to me how to break it in correctly. If there is no spark, then try a new spark plug. If the spark does not appear, then this means that the ignition unit is damaged and the saw must be carried in for repair. True, visual observation of a spark does not mean that the ignition unit is working. If there is a spark, but the chainsaw did not work, do the following steps in the list.
4. If there is a spark, but the spark plug is wet, then turn the chainsaw over to drain excess gasoline from the cylinder if it has accumulated there. Pull the starter without a spark plug 10-15 times to ventilate the combustion chamber. 3.1 how to dilute gasoline for a Stihl 180 chainsaw? 3.2 how to start a Stihl 180 chainsaw? Ignite the candle and screw it back, but rather change it to a new one, if any. Again try to start according to the instructions.
5. If the candle is dry, then draw one or two cubes of gasoline mixture into the syringe and pour it into the cylinder. Try to start a chainsaw - perhaps a small speck has got into the carburetor, which prevents fuel from entering the combustion chamber. It is quite possible that this mote will be pulled out by the flow formed after starting the chainsaw by adding fuel directly to the cylinder.
6. Unscrew the muffler and remove it, being careful not to damage the gasket between the muffler and the engine. how to start how to properly clean a chainsaw Chinese chainsaw. Try starting without the muffler and air filter. With the silencer removed from the chainsaw, you can inspect the piston from the inside. Why do you need to break in a chainsaw? How to properly break in a new or repaired chainsaw Stihl, Husqvarna and others. If there are burrs or burrs on the walls of the cylinder or piston, or the ring on the piston is jammed with burrs, then you will have to be very upset, as this means that the piston is damaged or worn out. This usually happens when there is not enough oil in the fuel mixture. With such a malfunction, you will have to contact the service, and possibly think about buying a new chainsaw, since replacing a piston one is a rather expensive operation.

Read also

Do-it-yourself repair of the Partner 350 chainsaw. Malfunctions and their elimination Saw "Partner 350" has decent power and is very convenient to use. However, the flywheel in this model is not designed for long-term operation. If the engine overheats, various breakdowns can occur. Ch...

All chainsaws from the Shtil manufacturer have two-stroke engines. They are carried out according to a similar algorithm. However, on sale you can find models that have optional equipment, with it you can start the saw without applying special efforts. For this reason, the starting method may differ.

Algorithm for setting the saw "Calm 180"

If you are faced with the question of how to start the Stihl chainsaw, then this process can be considered using the model 180 as an example. In order to carry out cold work, you must turn on the ignition and set the engine control lever to the lower position. In this case, the carburetor damper will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture has entered the cylinder, and the equipment is ready for the establishment. Before starting the Stihl chainsaw, you must set the control lever one position up. In this case, the air damper will open, while the throttle will remain in the same position.

The starter needs to be pulled and started. The tool will work on increased speed, the throttle will be open. To set the latter to idle mode, you should use the gas trigger and release it. The tool should now work normally. On the described chainsaw model, there are no additional devices that would make it easier to start.

This device, compared with the previous one, has some differences in the trigger mechanism. However, there will be no changes in the launch algorithm. The described version of the equipment has a system that, using a spring in the starter of the saw, reduces the resistance of the engine.

We start the MS 211 C-BE brand saw

If you, too, were among those consumers who thought about the question of how to start the Stihl chainsaw, then as an example, consider another model that was mentioned above. In it, the supply system is equipped hand pump, allowing you to start the saw easier on a cold one.

The instruction contains an additional clause that indicates that before starting, it is necessary to pump fuel into the carburetor using a pump. Next, you should act according to the principle that was described for the model 180.

Starting a saw after winter

If you are faced with the question of how to start the Stihl chainsaw after the winter, then you should read the recommendations. From consumer feedback, it can be understood that after long downtime some users cannot start the equipment. For a successful launch, you need to take care of the saw in advance.

Before storing it, drain the fuel, and then start the engine and burn the fuel that remains in the system. Preparation is necessary so that the membranes do not stick together during storage. This simple operation will allow you to start the saw after the winter. If you still don’t know how to start the Stihl 180 chainsaw correctly, then you should know that it will be easier to do this if you add 2 ml of fuel mixture to the cylinder through the spark plug hole before starting. This can be done with a syringe.

Saw insertion with decompression valve

Users sometimes ask how to start if the instrument has a decompression valve. The 250 does not have one. As soon as the first flash occurs, the valve will be in normal operation. The engine control lever will be set to the position when the choke is open. The launch will continue, the decompression valve must be pressed again. It does not make the launch quick, but it simplifies the process and makes it comfortable, because during the launch the operator will have to make less effort.

If you are not quite sure that you know how to start the Stihl 180 chainsaw, then remember that equipment with a valve, regardless of whether it has a hot or cold engine, must be started using the valve. This will make it easier to crank the engine. So you can extend the life of the starter and reduce the number of broken laces, because such chainsaws have a larger cylinder volume and compression.

Overview of the MC 180 chainsaw

This model of equipment costs 11,490 rubles. It is a household tool that will help you cope with work on suburban area. With the help of the unit, you can get rid of unnecessary knots and cut small trees. The control is single-lever, and due to the low weight, it is very comfortable to work with the unit.

The consumer should be aware not only of how to start the Stihl ms 180 chainsaw, but also of technical specifications. Among others, a 35 cm tire should be distinguished, as well as an engine with a volume of 31.8 cm 3. The volume of the oil tank is 0.15 liters. The equipment weighs 3.9 kg. The power of the model is 2 liters. with. The capacity of the fuel tank is 0.25 liters.

Overview of the chainsaw "Calm 250"

You can buy models 250 at a price of 29,542 rubles. This equipment is a semi-professional model with a 40 cm tire. Power is 3.1 liters. with. or 2.3 kW. The fuel tank capacity is 0.47 liters.

Quite often, before buying, consumers are wondering how to start a Stihl 250 chainsaw. This was discussed above. However, this information is not the only one that should be read before using the model. Other features include:

• single lever control;
• the presence of a compensator;
• anti-vibration system;
• side chain tensioner.

By purchasing this model, you will be able to carry out its quick refueling. This feature is implemented by a lid, which has a patented design. The operator, working with the equipment, will have reliable protection hands Consumers especially highlight also the toothed stop, as well as the chain, which guarantees high-quality and fast sawing of wood.

Conclusion

After purchasing the equipment described in the article, you should ask how to start the Stihl chainsaw. This information will help you extend the life of your tool. After all, improper handling of it can cause rapid wear of some parts. It is especially important to know how to prepare the unit for a long downtime. This was discussed in more detail above. After reviewing such information, you can understand how to prepare the device for winter storage.

Sometimes technical specifications tell some consumers about the launch features. If it can help you too, then you should read them. Some of them were presented above, but their complete list is presented in the instructions, which are necessarily supplied with the equipment.

Malfunctions of the Stihl MS 180 chainsaw and their elimination

Chainsaw in operation Calm MS 180. How to start a chainsaw Calm 180. The problem in the future. Before conservation for the winter, on the advice of mechanics, I dropped 4 drops of engine oil (calm) into the hole of the candle. twisted the candle. At the moment I was going to go to the country, I decided to look at the saw. How to start a chainsaw in the most that after a long idle time of the saw, start it with. I pulled the starter but it won't turn! I turned out the candle, it was in oil, rubbed it back. the same. Turned it over, turned the starter without a spark plug, everything spins completely. Turned it back on and the starter wouldn't turn. What could be?

Flush the chainsaw with clean, undiluted gasoline, fill directly through the spark plug hole and slowly turn the starter. Later, drain the fuel and the latest. After all these manipulations, dry the saw and the candle, and only then try to start it. Once you have learned to conserve, then learn and re-preserve, and not just pull and go.

Can you tell me why the starter is sticking? The Stihl 180 chain saw is brand new.

You don't understand, you don't know. Maybe the starter cord does not fit well, or maybe somewhere the ebb is interfering. Shtilevsky starters are quite reliable and durable. Any diseases of a constructive plan are not observed, the main thing is either mud or saturated exploitation. Once the chainsaw is brand new, bring it to the service center under warranty and they will repair it.

I'm at my own chain saw Stihl MS 180 saw one feature: when the tank runs out of gas, the revs idle move increase and the chain begins to spin even when the trigger is released. When you press the gas, the chainsaw stalls. This continues for a couple of 10 seconds, then the chainsaw stops. On motor vehicles, I did not follow such a phenomenon, so that with a lack of fuel in the carburetor, the engine speed would increase. Why is this happening?

This is normal for two stroke engines. With a decrease in the supply of gasoline to the carburetor, the consistency becomes leaner. Consequently. increase in speed, deterioration of acceleration. Accompanying this is a short-term overheating of the CPG. The engine will not disable, but it will not add health. Avoid running out of fuel from the tank to the end.

There is a chainsaw Stihl MS180, used in holiday season at the harvesting of firewood. In the near future, the reaction of the chain began to disappear when you press the gas, the chain does not spin at all, or in jerks. drinking is unrealistic. How to start a husqvarna chainsaw. What could be the breakdown?

For a completely new chain and sprocket, the tension must be exactly according to the annotation. so that the lower branch does not sag. and the upper fingers could be taken out to the height of the leading link. Then the chain will walk quite freely on the tire. But, the gradual wear of the sprocket teeth reduces its pitch. And the gradual stretching of the chain increases its pitch. and there comes a time when the steps of the same sprocket and chain no longer coincide to such an extent that the recommended tension already causes difficult movement of the chain. In this case, we recommend that the tension be slightly reduced. Right up to the appearance of a certain sag of the lower branch. By the way, for the same reason, it is recommended to use a pair or even three chains on one sprocket. In this case, wear is moderate and there will be no accelerated wear of the newest chain on an old, partly worn out sprocket.

Chainsaw Calm 180 after start-up, when you press the gas, it "chokes" and if you start sawing, it stalls. But if you torture with gas for 30-40 seconds, it starts to work normally. developed 3 liters of gasoline, clean filters, oil from the dealer.

If it started not so long ago, then most likely something got into the carburetor with bad fuel. Needs to be cleaned.

I would like to purchase this unit. What should be paid attention to during the inspection?

Not to mention the engine itself, since it is better to diagnose it in the service, you can look at the rest and get a lot of information. Significant mileage will be evidenced by: Dangling latch of the top cover. (Must lock tightly and not rotate from vibration). A brand new star on a battered chainsaw. With the cover removed, the movement of the motor relative to the housing. Sheared chain catcher and chain damage on the sprocket cover. You can also look closely at the carburetor on the left side along the way. where the wire rod enters the choke shaft arm. For a slightly working chain saw, it will be even, oblong. The longer the saw has worked, the greater will be the development of this hole. It rubs through from time to time. Under no circumstances should you take a saw that has at least a small free play of the right end of the crankshaft relative to the motor. This is a sign of an imminent renovation.

How many seconds should the engine run chainsaws Stihl ms 180 at idle before shutting it off?

Let it run for about 20-30 seconds and then turn it off. Their cold start is a review of the ms 180 chainsaw. How to start a Stihl ms 180 chainsaw. More. there is no point.

The idling began to disappear, at first I did not understand what was the matter, and later I remembered that I needed to add a lot idle move I added on a hot engine like it happened. I arrive in a week at the dacha, I need to cut a couple of logs, start the saw and at first the chain spins on a cool motor, then everything goes away, I stood for about 10 minutes, I start everything normally only on a cool motor. This is fine?

If the chain turns, then the speed is too high. It should be understood that a normally adjusted and serviceable motor is completely likely to have a slightly overestimated idling immediately after starting before warming up. And it can be decently elevated. before chain rotation. As the engine warms up, the idle speed gradually drops. For this reason, it is recommended to adjust the idle speed only on a warm engine.

Is it possible to put a clutch drum with a removable crown on a Stihl MS 180 chainsaw ("modernization" of the drum is allowed), for example, from the 250th.

Read also

Can. Everything fits perfectly. Just don't run over to 325". It's hard for the motor. But a couple of aspects should be kept in mind. 6: 7, respectively, the load on the engine will also increase. But practice has shown that this is not critical with normally sharpened chains. And secondly, a brand new chain of 50 links is difficult to put on such an asterisk. (In general, 51 links are recommended, but they happen occasionally). The first time you have to suffer so that she gets on the sprocket and the tire. And later, when she stretches a little, everything will be fine.

I bought a Stihl 180 chainsaw. I filled it with oil, benzyl. Started and gave to work without load at idle. I burned a tank of gasoline, at times I pressed a little on the gas. For some reason, the oil for lubricating the chain did not arrive, the oil hole remained dry. Or will it start to flow when the revs are higher and the chain spins longer?

How to start Calm 180 video

how to start calm, start chainsaws Stihl how true start chainsaw Stihl 180 1st video launch

Stihl ms 180 video

Wholesale and retail sales, service center, spare parts for products STIHL in Krasnoyarsk in the Trade and Service

At the 180th calm, oil is supplied to the chain when the drive sprocket is spinning (in short, when the chain is spinning), but on idling rolling is not recommended.

On the MS 180 chainsaw, after using the 1st tank of fuel, I had more than half a tank of oil left. The ditch of the tire and the base of the chain, which is in the groove, are in oil. How to start a chainsaw calm, husqvarna, try to start the saw again. But when checking, for some reason the oil does not squirt from the chain and the cutting teeth, in my opinion, remain dry when sawing. Wood plaque appears on the upper part of the cutting tooth. Oil comes in, but comes out in the missing volume. Nothing could clog, the chainsaw is brand new, the hole is clean. Marriage of the manufacturer or as it should be?

I will not argue about the consumption of chain oil in calm weather, but 2-3 tanks of fuel per tank of oil is not much? I have less than a quarter of a tank of oil left after a tank of gas is used up.

When I start the tool with the chain brake off, it cuts in from time to time just when I pull the starter handle. Is it normal?

This model is quite peculiar in launch, there is no decompressor and / or elastostart that compensate for the recoil, and despite the small size of the piston, it is decent enough. Because of this, the saw must be started confidently smoothly by engaging the starter sharply and moderately pull the starter cord, it is worth at some point to loosen your grip or slow down the pulling speed, as the recoil will remind you of an unpleasant feeling.

What is the difference between the Stihl MS 180 chain saw with a 30 cm bar. and with a 35 cm tire? i.e. the distance from the spike to the tip of the bar?

So this value changes during use. The more the chain is stretched, the greater this distance. And the longer the bar, the greater the difference in cut lengths between the newest and the stretched chain can be. The difference in the length of the cut between the completely new and stretched chain will be about 1 cm in some places. The bar does not lengthen, but simply its tip moves further away from the saw body, otherwise the chain will not be stretched. The limit for the growth of the length of the cut is determined precisely by the length of the tensioner screw and in what place of this screw the tensioner cracker was when installing the new chain. The farther it was from the leading sprocket, the faster, other things being equal, the chain will become unusable due to excessive stretching. I am afraid that it is unlikely that it will be possible to purchase a tire that is 1 cm longer than the standard one. How to start a calm, start a chainsaw calm, how to start a chainsaw calm 180 the first start of the video. Regular tire lengths for consumer models. 12", 14", 16" and 18" for 3/8" x 1.3 mm chains and 13", 15" and 18" for 0.325" x 1.3 mm chains.

Is it possible to keep the brake off when starting, or must the brake be on?

And this is both more convenient and safer for you. There are three main launch options. on the Idling, at half throttle and at full throttle. In the first case, the chain is stationary after starting or may twitch a little. How to start a chainsaw The question of how to start a chainsaw can be divided into two parts: winding up according to the annotation what to do if the information from the first part does not work out will be useful to those. In the 2nd and 3rd cases. the chain is moving. Setting the brake to the working position in the first version of the start is a waste of time. It is very unlikely that the idle speed at one moment and without circumstances would increase so that the chain would begin to move. In the 2nd and 3rd cases, when starting with the brake activated, it is necessary to immediately release the brake after starting so as not to burn the clutch. When starting with the brake off, after starting, it is necessary to press and release the gas lever so that the saw engine switches to idle mode (in the 3rd case, this lever is already pressed at the time of starting, it only needs to be released).

It was necessary to work, the saw started up rapidly, although it stood idle for 5 months, sawing everything that was needed, burned one tank of fuel, everything is fine. But I arrive in a week, under it there was a puddle of oil before there was none. What could it be?

Never happened on these chainsaws. Usually breaks the oil hose from the attachment to the pump, if you throw cool oil in the tank and put the saw in heat. The breather only works inward, the pump does not let air through, so there is nowhere for the extra pressure to go, well, it squeezes out the hose.

I bought a chainsaw Stihl MS 180 C-BE. Started by annotation. The consumer should be aware not only of how to start the Stihl ms 180 chainsaw, but also of the technical specifications. Everything works fine, but very long and a lot of action. I tried to start without a brake in position I, and it also started up the first time. Tell me, is it possible to do this and what can it threaten?

It is better to start without a brake, the clutch will burn out quickly. Warm generally just starts.

Now my instrument is not working. I unscrewed the spark plug and it was wet. Laid on gas burner tried again later. Doesn't start at all. I pulled out the candle 5 times, and it was always wet. What to do?

You try and not dry the candle. How to start a chainsaw video. I them, flooded. I usually start it like this: I unscrew the candle, turn off the ignition. Jerks 10. 15 starter (if very flooded, put the muffler down and pull). Later, I blow a candle on the candle to bring down the excess fuel and screw it in. But later I start not from the lowest position, but from the second from the bottom (the air damper is open and the “starting” gas is given). Usually a jerk from the third. the fourth starts. A bit of smoke and everything works. And from time to time it is too lazy to turn out the candle, so I give full throttle with my foot (on the ground, of course) and pull until it starts. In most cases it will work. And if, after blowing and drying the candles, you start again from the lower position, then fill it up again. there is already an excess of fuel, and we will also close the damper.

During operation, the stihl ms 180 c chainsaw did not idle and stalled. Started with difficulty, but stalled again at idle. After that, it won't start. The next day, after unsuccessful attempts to start, removed and washed the air filter. It did not help, I had to remove the candle. turned out to be dry, although attempts start there was plenty. I cleaned the breather with a needle (it was not clogged). I changed the fuel filter (although the old one is not visually dirty). I cleaned the carburetor and put in a brand new spark plug just in case. The saw won't start! Pulled out the spark plug again. dry. On chainsaws Stihl ms 180 as idling on a chainsaw. What to do?

Remove the muffler. Look at the piston, if it has longitudinal stripes, then a replacement is required.

I have been operating the Stihl 180 chainsaw for the 6th year, I took the newest one. Satisfied with the saw, apart from oil, filters and bearing grease, I didn’t touch anything, I did decent work over the years. This year I had to cut a lot, worked for three days. On the 2nd day, the saw began to trim, you seem to be gasping normally. On the 3rd day, the turnover fell by about 2/3. It runs at idle, it can stall from time to time, it does not start the first time. Yesterday put more did not touch. How to assemble a stihl ms 180 chainsaw after purchase. What could be?

Read also

I would take a look at the muffler. If it hasn’t been cleaned once in 6 years, it gets clogged and the exhaust gases have nowhere to go. Usually, with these symptoms, either the air filter is clogged, or the muffler.

Not so long ago I found out that better at times turn the tire on the chainsaw. for even wear. Tell me, is it worth it?

Spinning a tire isn't just better. certainly. With what frequency. depends on the amount of work. Not only twist, but also grind off burrs.

What is the difference between the drive and chain sprockets of the Stihl 180 chainsaw?

There is no difference between the "drive sprocket" and the "sprocket wheel", these are different names for the same part.

I bought this chainsaw, I really liked it, but I want to ask you if my saw can cut a thick tree?

Standard tire length. 35 cm, can be sawed log. 70 cm in diameter, if logs of such a diameter prevail, then you need a chainsaw with more power. The tool will, of course, cope with the task at hand, slowly and correctly cut all the logs of a huge diameter, but you need to keep in mind that by giving huge loads to an apparatus that is not designed for this, you (in best case) we reduce the resource of the chainsaw, in other words, we bring its complete repair closer.

Can you please tell me if a 45 cm bar can be used on a Stihl 180 chain saw?

The chainsaw can be fitted with a bar with a maximum length of 40 cm.

Where is the breather in the Stihl ms 180 chainsaw?

Valve ventilation system("breather") is located "on top" of the gas tank and oil tank; everything is covered by the starter housing.

AT horizontal position the gas button sticks. What to do?

Most likely, the lever-traction mechanism is faulty; when the unit is turned over, one of the levers or rods “sinks”.

Why is oil not supplied to lubricate the chainsaw tire? What is the problem?

The oil filter is clogged. The channel in the chainsaw body is clogged. The channel and the groove of the tire are clogged. Faulty oil pump drive (worm). Oil pump defective. The oil in the oil tank has run out.

What can you say about the overheating of the motor chainsaws Stihl 180?

I will try to explain about overheating of a serviceable chainsaw. I understand a working chainsaw as follows: the carburetor is correctly adjusted (it is enough to set the idle speed normally, by ear or by tachometer 2800), bearings, oil seals, filters, a candle. in order. The cooling system should also be in order, otherwise it happens that you can’t see what color the starter cover is, the grill is clogged, the air practically does not pass. If serviceable chain Saw will run on a regular fuel mix (high-quality gasoline with a fairly high octane number, not a bad two-stroke oil and its correct proportion). it is then that it cannot actually be overheated (sharp chain, of course). What could be the reason that saw Stihl ms 180 not. The reason for overheating is directly related to the fuel, you can overheat the newest saw in 5 minutes, while still working. Cause of overheating. not work or its duration, but fuel or oil. Or this and that. And with home, moderate use, subject to all of the above, this tool will never overheat.

On all Stihl chainsaws, two-stroke engines are installed, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed that allows you to start the saw without excessive effort. For this reason, their start algorithm may differ slightly.

Let's see how to start ordinary saw and how the process differs from running a modified model.

In order to start the Stihl 180 chainsaw cold, you must follow the algorithm specified by the manufacturer in, namely:

1. Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper blocks the air from the air filter, and the throttle is fully open, thus the fuel mixture is enriched);
2. Pull the starter handle several times until the first flash passes (the flash indicates that the fuel mixture has entered the cylinder and the saw is ready to start);
3. Set the control lever one position up from fully lowered (in this position, the air damper opens, and the throttle remains in the same position as before);
4. Pull starter and start. The saw will start and will run at high speeds, due to the fact that the throttle is as open as possible. To set the damper to idle mode, you need to press the gas trigger and immediately release it, the tool immediately normalizes speed.

On a chainsaw standard equipment not installed any additional devices to make it easier to start.

Below you can see how to start a calm 180. The video reflects in detail all the main points, and the author's comments allow you to understand the whole process to the smallest detail.

We start Calm MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does not carry any changes in the launch algorithm. The fact is that in calm 180 C, the ErgoStart system is installed, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance during start-up.

Starting the Stihl MS 211 C-BE

The fuel supply system in the Stihl MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold one.

The instructions for starting this model of the Stihl chainsaw contain one additional item, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from the start of calm 180 and follows the same algorithm.

What happens at the moment of pumping fuel with a primer, and how does this help to start the saw more efficiently?

At the time of starting the saw without a primer, several movements of the starter are carried out only so that the gasoline pump, under the action of an impulse from the saw crankcase, pumps fuel into the carburetor.

The pump installed in the fuel line allows you to manually, without unnecessary movements by the starter, pump gasoline into the carburetor. The effect of such an action is obvious, the saw will start much faster.

Many owners of gas tools mistakenly believe that a manual pump can over-pump fuel into the carburetor and, for this reason, fill the candle. This is fundamentally wrong, because the system is able to circulate around. Excess gasoline from the carburetor will be directed, through a special hose designed for this purpose, back to the tank.

On a hot chainsaw, there is no need to use a primer, because there is enough fuel in the carburetor to start.

How to start a chainsaw with a decompression valve

Before you start the Stihl chainsaw on which the decompression valve is installed, you must turn it on. It should be noted that there is no decompression valve on the Stihl 250 saw.

After the first flash has passed, the valve will return to normal operation, so after the engine control lever is set to the open choke position and starting continues, the decompression valve must be pressed again.

Schematically, the operation of the valve is shown in the figure below.

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because. for during launch, a person will have to apply much less effort.

A saw with a decompression valve, whether the engine is cold or hot, must be started using the valve to ease the cranking force of the engine. This will significantly increase the life of the starter and reduce the number of broken laces, since it is installed on chainsaws with a large cylinder volume and, accordingly, compression.

How to start the saw after a long period of inactivity

I can not, after a long downtime. Such comments can be found on forums dedicated to the repair and operation of saws. Let's figure out how to start a chainsaw after a long period of inactivity.

The point is that about successful launch after a downtime, care must be taken in advance and properly prepare the saw for storage. According to the manufacturer's instructions, before storage, it is necessary to drain the fuel from the tank, then start the engine and burn the fuel in the fuel system.

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after a long period of storage.

It is much easier to start a chainsaw six months after being idle, if immediately before starting, through the candle hole, add 1-2 ml of the fuel mixture to the cylinder. This can be done with a syringe.

Results

Starting the Stihl chainsaw almost always follows the same algorithm, with the exception of those cases when a decompression valve and a fuel primer are additionally installed on the chainsaw. These devices are designed to facilitate the start-up process and do an excellent job of their functions.