Waterproof sealant, neutral construction silicone, construction sealant, aluminum sealant, metal sealant, assembly sealants. Elimination of leaks and repair of the drainage system Instructions for the use of liquid nails
Autumn has arrived and it has been raining heavily. If you haven't already done so, it's time to thoroughly prepare your dacha or country house for the three cold and wet seasons. Common places where problems regularly occur are the roof and external gutter system. Before you know it, winter will come, and then the drain will have to withstand the additional load in the form of ice and snow and at the same time protect your home from a lot of water. The appearance of a leak during such a load threatens not only with puddles in the wrong places on the site, but also with damage to the building itself and its foundation, water entering the house and partial destruction of the water drainage system. Thoroughly checking and repairing, if necessary, or suspecting a future leak in the external drainage system, is a critical moment in preparing a home for the cold.
To you will be required:
- stairs;
- mechanical drill or perforator;
- clean rags in large numbers;
- a long hose connected to the water (can be temporarily attached to the faucet in the kitchen);
Silicone seal;
- a gun for a tube with a silicone sealant;
- durable sharp knife;
- bolts for the gutter.
1. Place a ladder under the section of pipe (in the center) that you are going to work on - this is the most convenient position. Wear waterproof pants and a raincoat so you don't get smeared with what will spill and fall out of the pipe or gutter when you remove the section. Climb up and remove one section adjacent to the leak. Loosen mounting bolts/rivets mechanical drill while holding the section in place with the other hand.
2. Clean the edges drainpipe that remained on top, as well as the removed section, but with completely clean rags. Wipe all areas thoroughly and remove any substances (adhesive, sealant, grease, etc.) that held the pipe sections together and/or sealed them in the past. Wash off dirt and other residues with water under pressure from a hose. Grab a wire brush (if the pipe is not plastic, of course) if necessary and clean off the remnants of all the same material that previously served to seal the junction of the sections of the downpipe.
.jpg)
3. Insert the silicone tube into the gun, put it in place and cut off the long, sharp nose of the tube at a slight angle with a knife. Hold the gun next to the next edge of the pipe fixed on top and coat the entire edge with silicone in a circle inside and outside within (both edges to the right and left of the removed section, but in turn - see step 4) 5 cm from the edge. This will give you a seal that seals the pipe when you put the sections back.
4. Immediately insert the old, previously leaking section, which was removed and cleaned before, into or on the section to which the silicone sealant has just been applied. Push the section in until it is firmly in place. Silicone must adhere to internal surfaces downpipe sections. Repeat on the opposite side of the section.
5. Insert the pipe bolts (usually 1.2-1.3 cm long) in the proper places at the intersection of all sections of the drain on the right and left. Screw them into place. Then grab the pipe with your hands and check that everything is carefully fixed and tightly connected to each other. Ready!
A leak in the gutter is repaired by analogy!
Attention! When working on ladders and when stacking tools on a roof, be very careful not to lose your balance and/or drop the powered tools on yourself and others.
In order for the drainage system to work well for a long time and protect the roof, walls and foundation of the building from leakage and excessive moisture, it is necessary to properly care for the gutters.
In the event of their slightest damage, it is required to immediately repair and replace the broken element with a new one, or repair the damage using soldering, sealant or other waterproofing technology.
Such repair and maintenance of the drainage system can be performed by any owner. country house if you follow a set of rules. If the owner had to deal with more complex repair problems, then you should seek the help of qualified specialists.
Service life and quality drainage system determines the quality of its maintenance and timely repair and preventive maintenance, during which the drains must be cleaned of debris and dirt. The accumulated debris usually clogs the drain, preventing water from escaping down the drainpipe or gutter. As a result, the performance of all systems is disrupted and breakdowns occur. Stagnation of water leads to destruction metal elements, causes their corrosion and subsequent deformation.
When conducting technical inspection drains, first of all, you should inspect those places that are more prone to clogging and subsequent deformation.
This usually happens at the joints. various elements drain. If blockages are found, they must be removed immediately.
Often during operation, mechanical damage to the elements of the drain occurs. Fallen hail, stones carried by gusty winds, ice can cause cracks, deformations and breaks in the drainage system, which should be promptly eliminated upon detection.
When are repairs needed?
Gutter repairs are often required when:
- the appearance of rust in some of its places;
- when cracks appear plastic elements with temperature changes;
- when the drainage system swings under gusts of wind and its elements rattle from gusts of wind;
- when a leak occurs at the junctions of the elements of the drain;
- when pouring storm water through the gutters and too slow its flow through the gutters of the stormwater.
Drains begin to rattle and sway if they are not well attached to the wall or roof. Overflow of water in the gutters occurs due to their clogging or due to congestion at the junction of individual elements. During operation, the drainage system begins to silt due to the accumulation of dust and fallen leaves in it. Therefore, it must be cleaned regularly.
In order for the gutters to stop swaying and rattling, it is necessary to tighten the fasteners and clamps. You should also eliminate damage at the junction of individual elements. This is all in general to improve the work of the drain. In the event of leaks at the joints, their tightness must be restored. With the help of modern sealants, this kind of problem is easily solved.
If the leak appeared due to significant damage to the entire gutter element, then it should be replaced with a new one. To do this, you will need to purchase a similar unit in a specialized store and carry out repairs.
In some cases, the repair of gutters in country house can be done on your own. This is for minor damage.
Replacing broken gutter parts
To replace the middle link yourself storm system damaged as a result of a crack, you will need:
1. Loosen clamps in place damaged area drain in the lower part of the drain, located vertically.
2. The lower structure must be lowered so that it can be turned to the side, so that later the worn element can be removed from the common vertical system drain.
3. Remove the fastening of the clamps at the junction of the old element of the downpipe.
4. Move the damaged downpipe element aside and carefully remove it.
5. Install the new element in reverse order. Before attaching a new segment of the drain, it is necessary to thoroughly clean the joints from contamination.
We eliminate leaks
To eliminate leakage in the gutters of the drainage system, it is possible to apply patches in places of damage, which are made from a special reinforced tape, steel piece with galvanized coating. To restore the tightness of plastic drainage systems, special fiberglass or rubberized fabric is used. Breakdown technology includes:
1. Cleaning the damaged area from contamination.
2. Solvent treatment to degrease the surface.
3. Lubricate the surface of the gutter to be repaired with sealant or epoxy glue.
4. Apply to the surface with adhesive patches and firmly
its fixation.
Often, to restore the working slope of the gutters, it is necessary to completely change the system of fasteners and brackets.
Properly conducted timely minor repairs drainage will help extend the life of the entire drainage system and save money that will be required for complete replacement such a system in the event of a malfunction.
To avoid breakdowns, it is required to carry out preventive maintenance of the drain in a timely manner, which includes regular cleaning of gutters and pipes from blockages. This will extend the life of the drainage system and help avoid breakdowns.
The strength and reliability of any roof depends on a properly arranged external drainage system, which ensures the drainage of water from the roof surface. However this system able to work only with correct installation, as well as when using sealants. The sealant for the gutter system is necessary element, since it is he who is able to effectively seal the connecting seams and joints of individual elements of the drain.
The drainage system is complex structure, therefore, a special butyl-based gutter sealant is used for it, which has increased resistance to temperature extremes and remains resistant and plastic in any conditions. It adheres well to aluminum, galvanized and vinyl-clad surfaces.
Waterproof sealants recommended for repairing cracks, holes, punctures in gutters and drains. Before use, the surface is thoroughly cleaned and dried. It should be applied at a temperature above 4 0 С. high humidity nessesary to use silicone sealants for wet rooms suitable for both indoor and outdoor use.
You can buy a sealant for a drainage system inexpensively in our online store, where they are presented in a wide range of color scheme. This allows consumers to match the sealant to the color building materials for which it is used to seal.
roof leak, wet walls and dampness in the house even after a light rain - problems that residents of houses may encounter, on which there is either no drain, or its installation was carried out incorrectly. Gutter systems are divided into two types: external and internal. Internal drain, called storm, is mounted during the construction of a building with flat roof, the pipes of such a system pass inside the building and their purpose is to ensure the flow of water from the roof so that there are no puddles and leaks. at home with sloping roof install external drains into which water flows, and they also prevent the appearance of icicles in winter.
Drainage systems are made up of metal pipes, gutters, fastening and sealing elements. Most often, gutters are made from of stainless steel, aluminum and metal-plastic, as these materials are durable and practically resistant to corrosion. When installing a drainage system, special seals are used to seal the seams. assembly sealants and sealants for metals company SDM-CHEMISTRY.
These silicone-based sealants are non-corrosive, capable of withstanding loads within minutes of application, and have high elongation at break (600-650%). These materials provide good fixation of both identical and dissimilar materials: aluminum, most types of metals, plastic, ceramics, glass, etc.
Sealant for aluminum and other metals, resistant to aging, aggressive substances, weathering, ultraviolet, is able to maintain its properties in the temperature range from - 40°C to + 180°C. It? waterproof sealant which is suitable for sealing expansion joints. This material has high elasticity, so it completely fills the seams in the metal.
Since silicone sealants for metals, which are used to seal joints in the gutter system, are often exposed to moisture, they contain a fungicide - a substance that prevents the growth of mold and fungi.
These quality waterproof sealants after curing, they become neutral, odorless and non-toxic, so they are suitable for both outdoor and indoor use. internal works. Sealants that seal seams in aluminum and steel are available in a wide range of colors. This makes it possible to match the sealant to the color of the building materials for which it will be used.