How to make a hole in a belt. Men's ties wholesale. Electric drill to help

How to make holes in a belt?

The hot nail is only suitable for a plastic belt or a belt made of faux leather. For genuine leather, this is a bad option.

The best punch is a tube with a sharpened edge. Only under the cone it is necessary to sharpen the INSIDE of the tube. And accordingly, the diameter of the hole - this will be the outer diameter of the tube. Such a tube will give a hole in the belt with strictly vertical walls. A tube sharpened to a cone on the outside will give a hole slightly widened to one side of the belt.

Drill - too a good option, but here you need the right equipment: the belt must not only be put on something, but squeeze between two planks. Solid (compared to skin) wood will not allow the skin to - the hole will be even throughout the thickness. Of course, here you have to be very careful with the markup - after all, you will have to drill blind ...

Take a thick needle, but be careful. This is if the belt is not too tight. You can try with a stationery awl or crochet hook. Scissors can help too. Observe safety measures in everything!

In order for the hole in the belt to turn out neat and over time not you can do the following. take a nail desired diameter, clamp it in pliers and heat it on fire, for example, over gas stove. The main thing is that it becomes very hot. Next, put the belt wrong side up on a pre-prepared wooden board and carefully make a hole with a nail in the right place. When the nail has cooled, heat it up again. Do the same on the outside.

with a thin tube, depending on the tongue of the belt, you can use shells from small things if you need a small hole, and if you can use more shells from Kalash, well, you can make the tube yourself from a tin from under an iron can of beer

And my husband and I discovered another way, without heating nails and awls. We have a drill, we insert a drill right size, put the belt on the plank, whack and you're done. Very carefully, you want a very thin hole, you want a huge one, it all depends on your desire and imagination.

You need to heat the nail and pierce it. Then the hole will be straight.

Even holes in the belt are made with a drill, manual or electric. You need to choose a drill of the desired diameter and drill as many holes in the leather belt as you need. And with the help of a gypsy needle, uneven holes are obtained.

One person told me: A hole only happens in a f..ne, and there is a hole )))

I can offer an option, a hole is made using notches - this is a thing reminiscent metal tube, one of the sides of which is sharpened under a conequot ;. The inner diameter of the tube should match the diameter you need. Then you just choose everything, measure the desired location of the hole, fit the tube with the sharpened side, hit the second end of the tube with a hammer and get the hole you need with smooth edges.

As I remember, my grandfather always made holes in the belt with a sharp awl, preheated over a fire. I make holes in the belt with the help of my husband - quickly, reliably, always with high quality.

Mark the place of the future hole, heat a screwdriver or an awl on the stove - if the belt is leather - you will have to make more than one attempt, and try to push through with force. Do not skid back and forth - the edges will be uneven and the hole will look sloppy.

It's very easy to sell special agent for belts and not expensive and useful, for home pants feast in size. With it, it is useful not only for belt holes, but for paper, cardboard, leather, and other products. The price is almost 30 rubles.

I constantly have to make a hole on a new belt myself, because small size forever not, and I do it with anything - with a clerical knife, an awl, a table knife, basically a clerical knife - you just need to carefully open it a little so that the latch crawls through and then you don’t need to cut it, it spreads a little and it won’t be noticeable that you yourself made a hole, just needs to be cut a little.

With a pen, measure the place where the hole will be. Then you need to glow (on the stove) an awl and make a hole of the right size with it. Well, buy a new belt for good))

You can use a drill.

There is nothing complicated here, the main thing is that there is a drill and you know where it lies)))

First you need to choose a drill of the required size.

Lay the strap on the board. Drill holes in the desired location with a drill.

Well, everyone does what they can. The problem is that it is not easy to make an even, not torn hole, besides, it is necessary to observe the distance between the holes so that it is not conspicuous.

Personally, instead of riveting new holes, I adapted to another solution - I use belts with the ability to disassemble them at the buckle attachment point and the main part of the belt (where they are fastened with a screw). I unscrew the screw, cut off the required length (I'm losing weight), punch new hole using a screwdriver bit that looks like an awl only thick (I did not find another use for it) and tighten the screw back. The hole turns out to be quite even, and if something doesn’t come out quite evenly, then you can’t see the screw under the head. And for fastening the belt on the belt, I continue to use the standard punched holes

Unfortunately, this method is not suitable for those who are getting fat.

It happened to you that you urgently need to leave, you get dressed, put a belt through the belt loops of your trousers, and you understand that you urgently need to make an additional hole. But as? The “fastest” option comes to mind - with an awl, nail or drill. But is it right? Will you damage the material from which the belt is made: will it “creep”, will it not “break” in the place of the hole made, will the hole made look aesthetically pleasing?

Secrets of the Samodelkin masters

Quickly, as the great strategist Ostap Bender used to say, only cats will be born. And he was right! No matter how you hurry, do not do what you have planned in a hurry. There are, of course, clever men and women who pierce holes in belts with what is at hand: nail scissors, a kitchen knife, a metal pointer. In principle, if the strap is not a pity, then you can break through with a nail. But then it must at least be heated so that the edges at the hole look more or less aesthetically pleasing. You need to pierce it by placing the nail with the point on the marked “point” where the hole will be, and then hammer it into the head of the fastener with a hammer. Over time, a new "hole" will develop when worn.

Someone recommends using a bicycle spoke or part of a retractable antenna. In diameter, they can just “coincide” with the holes already on the belt. But first, the metal tube must be sharpened with a needle file or file, and even special “teeth” should be made. They should be cut out by placing a self-propelled gun on a wooden base. Take your time, do everything carefully, and then you will have a ready-made "hole punch" that you can use at any time.

When your home punch has already been turned, the belt must be laid out on the table, and measure with a ruler where to make a hole. A homemade “sharpening” enters the skin quite easily, so this option is also useful for an expensive product. Here, as they say, a red-hot bicycle spoke will not work.

Puncher, he is a hole puncher

But still the most The best way- is to make a hole in the belt according to all the rules, which means without special punch not enough. What kind of thing is this? A punch is a device - a type of tongs - for cutting holes in textile materials, on leather, in cardboard and in plastic. In the store, a manual punch may also be called punching pliers or simply a belt punch. This tool is sold in large supermarkets such as "OK" or in "All for Sewing" stores.

The punch has several interchangeable punches in the set - tool parts that press on the material being processed. Punches have different diameters(from 2 mm to 5 mm), and finding the right one for your garment will not be difficult. Due to the fact that the punches have an even and smooth "sharpening", the holes when using them are beautiful and neat.

The action of the punch resembles the action of pincers. A punch of the required diameter is selected, set strictly perpendicular to the intended location for the hole, the tool is compressed and rotated with the handle until the desired result is obtained.

Hard pressure - and a new hole in the belt is ready! You will not get any injuries, as when using a sharp nail, knitting needle or awl! The punch guarantees a double effect - absolute safety and high results. In addition, this tool is inexpensive. It’s not a pity to pay some 400-500 rubles for a hole punch so that it is always in the home arsenal. And you don’t need to heat anything, cut it out and have a risk of getting burned or hitting your fingers with a hammer! In the future, you may need a hole punch for other purposes - what if you need to make an even hole in a thick fabric or plastic product?

How to make a hole

So let's get started step by step instructions how to make a hole in a belt with a punch.

Mark the point on the belt where the new hole will be located. To do this, you need to take a ruler and a felt-tip pen: the first tool is to measure the distance between two adjacent holes, the second is to put a point. The length between existing holes should be equal to the length from the last hole to the new one. It is necessary to put a point on the wrong side of the product.
Stretch the belt on the table inside out, and install something heavy on its ends so that it does not jump off a flat and flat surface at the most crucial moment.
Find on the punch and set "to action" a punch of the desired diameter.
Install the punch in the place marked with a felt-tip pen: the belt should be between the two halves of the tool.
Firmly squeeze the hole punch handle.
If the belt is too thick, then you will need an assistant who will “drive” it back and forth until the “sharpening” passes through the skin.
If a hole is made, but pieces of skin remain in it, they must be removed using some kind of thin and sharp object such as a toothpick.

Tip: If it is important for you that the belt “sits” exactly on the figure, then you need to try it on and mark the location of the new hole directly on yourself by pressing strongly on the buckle tab so that it “digs” into the material and leaves a dent on it. By quickly removing the belt, you can duplicate it with a marker.

Electric drill to help

If you intend to make a hole in the belt with an electric drill, then this is quite possible with care and skill in using the tool. Having chosen a drill of the right size, which will fit snugly into the hole, turn on the drill with a few short presses, gently inserting the pointed drill into the previously marked point. Such manipulations will make the hole in the belt neat and exactly in the right place.

Tip: If your belt type suggests a buckle with a screw that needs to be unscrewed and removed to make a new hole, then it makes sense to contact your nearest shoe repair shop for this service. By the way, this applies to everyone who wants to quickly and without physical costs to make a belt exactly to the figure!

How to make your own belt punch

If you have hands and know how to use them, then making this not a tricky device is very easy.

As you can see from the photo, I will use an ordinary telescopic antenna. This can be taken from an old radio, any remote control (children's cars), and in my case, this is a TV antenna. These used to come complete with a TV, and what was interesting for me, on the upper floors, they just worked fine for receiving TV channels.

True, for us it is too long, and therefore I shortened it. As you can see in the photo, it had to be disassembled. I did it, at first the usual hand saw, and then trimmed the edges with a grinder.

Now I select the tube of the desired diameter. I cut it into two parts, if you have a short tube, then you can not do this. Just a very long tube can then give a marriage. We will make a leather drill out of it, and when rotated, it can bend, thereby scratching or even tearing the product.

The optimal length of our drill should be about 10 - 15 centimeters. On one side, the tube is slightly rounded, this side will be our cutting part. On the other hand, we will need to insert some kind of plug into the tube. This is so that when you clamp a screwdriver or drill into a chuck, do not crush a thin tube.

It is advisable to pick up as tightly as possible, ideally a nail. The plug can also be made from a screw, self-tapping screw, or other handy material. Or even insert a regular drill.

Now we insert such a drill into a screwdriver (cordless drill) and make a beautiful hole.

The photo shows that the holes with a rounded cutting part are very neat. These are the two holes on the top right. The hole at the top left is made with a flat part, reverse side. The hole is even, but in the first case it also turned out to be polished.

The use of a special punch

How to make a hole in the belt as accurate as possible? A leather punch will help with this. You can buy such a device relatively inexpensively at any point selling handicraft tools. In order not to be mistaken with the diameter of the punch, when going to buy it, you need to take the belt with you. If you need to make holes in several belts, it is worth purchasing a tool with removable tips of various sizes.

In preparation for work, it is necessary to mark the plane of the belt by measuring the distance between the factory holes with a ruler. Then you should set aside the same segment on the plane and mark the location of the future hole.

Before using a leather puncher, it is necessary to fix the belt in such a way that its plane is in a taut state. Then it is enough to attach the tip of the punch to the intended area and squeeze its handles strongly. It is necessary to relax the hole punch for the skin as soon as its elements completely sew through the material.

Nails and hammer

How to make a hole in a leather belt? Most simple solution here looks like a breakout nail holes. The main thing is to initially determine the location of the future hole by taking the appropriate measurements. To make notes in the right places, just use ballpoint pen or a marker.

The work is performed in the following sequence:

a suitable nail is selected, the diameter of which should approximately correspond to the dimensions of the factory holes on the product;
the belt is located on a flat plank surface;
the tip of the nail is set to the previously planned point;
several accented blows are performed on the nail cap until its core completely sews through the belt;
the nail is rotated several times in the thickness of the leather product, after which it is carefully pulled out with the help of pliers.

At the end of the work, it is desirable to treat the edges of the resulting hole with a neutral shoe cream. In this way, uneven edges of the material at the point of breakdown can be smoothed out.

Electric drill

When thinking about how to make a hole in a belt, it is worth considering the option of using an electric drill. With care, it can be used to make fairly even, neat holes.

To begin with, it is recommended to fix the belt by pressing down on its ends with a weighty load. In this case, the area to be treated should be located on a flat, hard surface, such as a wooden block.

To decide on optimal size drills, it is enough to manually insert several rods of individual diameters into the existing holes on the belt. It is recommended to stop on a drill that will fit tightly enough into the hole.

How to do neat hole in a belt with a drill? To do this, you must first make a slight indentation at the intended point, using the tip sharp knife. As a result, the drill will not jump to the sides during the work.

Starting to make a hole, it is necessary to make short-term starts of the drill mechanism. In this way, the risk of making a sloppy hole can be minimized.

shoe awl

To cope with the task with shoe awl, first you need to mark the plane of the belt. Then you should place the product on a sufficiently hard plane, which at the same time can pierce the tip of the tool. You can lay the belt on compacted soil or a piece of foam.

Next, make a hole in the belt with the tip of an awl. If necessary, expand the diameter of the hole with any suitable metal rod. Pieces of material that formed on the inside of the product after breaking through can be carefully cut with nail scissors.

When trying to find a solution to how to make a hole in a belt, you should not resort to using the usual kitchen knife or scissors. Using such blades will not allow you to create neat holes.
Piercing thick rough skin may be enough challenging task. Therefore, when using a hole puncher, you may have to use the help of a partner.
The use of available tools, such as a hammer and nails, an awl or a drill, will not require additional costs. However, exploitation special tool designed for such work will save not only time, but also reduce the risk of accidental injury.
Before you start punching a hole in a leather product in one way or another, it may be worthwhile to pre-practice using a piece of old unnecessary material.

Summing up

So we figured out how to make a hole in the belt. The solutions indicated in the presented material will not force you to seek help from the workshop. The main thing is to do the work slowly and as carefully as possible so as not to spoil the product.

Both men and women are familiar with the problem when, when changing waist sizes, their favorite leather belt categorically refuses to fasten on the holes provided by the manufacturer. Naturally, in such a situation, people will immediately begin to make new holes at home and, as a rule, with improvised means.

Freshly made holes at home can significantly spoil appearance belt - if you do not know how to punch them correctly. Therefore, it is important to follow a few recommendations for the correct and accurate execution of belt holes.

A hammer will help you

First of all, attach the belt to your waist and mark the desired location of the new hole with a marker or pen. Then put the belt on wooden surface front side up, put a sharp nail to the mark and hit his hat several times with a hammer. Hit until the leg of the nail passes through the entire thickness of the belt.

Remember that the new hole must be located at the same distance from the other holes and be strictly parallel to them. Violation of this rule is fraught with damage to the entire product.

Be sure to lubricate the pierced hole with an ear plug. cotton swab and colorless shoe polish, thereby fixing the edges of the new hole.

If you are going to make a hole not in a leather, but in a riveted belt, insert another rivet into the new hole with a knife. Smooth the edges of the installed rivet with a hammer - so the altered belt will retain its original appearance.

We work with an awl

Make a mark on the intended location of the future hole. Lay the belt face down on a flat wooden surface, hold the sections near the mark with your fingers, and poke it vertically with an awl or a thick, sharp needle.

The wooden surface should be hard enough, but at the same time it should not prevent the awl or needle from piercing the belt through. Choose a comfortable and stable surface

After making a hole, take sharp nail scissors and expand the new hole with them. The width should be slightly narrower than the diameter of the belt tongue, as the hole will widen fairly quickly with use. To prevent the tongue from pulling the material behind it when passing through a new hole, bend the belt alternately in all directions so that the hole is located on its fold, and carefully trim the edges of the hole with very sharp tweezers.

If the belt is synthetic, carefully melt the edges of the new hole to help prevent peeling of the outer and inner layers of the material.

The main thing is accuracy, accuracy and accuracy again. But, if you are afraid that you will not have enough strength or skill, you can turn to a sewing or shoe shop for help. This measure will help to avoid damage to an expensive product.

Choosing a belt shopping malls, stores and Internet sites, you can substitute that different belt manufacturers always make a certain number of holes. In this situation, you can ask the seller to make these holes, but sometimes it is better to make them yourself, having previously measured right amount holes and the distance between them, specifically for your waist.

How to quickly make additional holes in the belt?

First of all, try on the belt with your favorite pants and mark where you think the hole should be. The belt should tighten the belt in the same way as other belts.

Look at how far apart the holes made at the factory are. Our hole should be at a standard distance from the others. The marked place will only help.

It happens that the existing holes on the belt seem to be enough, but you would like to make another one in the middle. In this case, it is not necessary to take care that it is exactly between the other two. You also do not need to make other holes that will create a uniform chain on the belt. It is enough that the hole made is neat.

Make a washable mark where the hole will be made. Take an awl or a thick, sharp needle. Lay the strap face up on a flat surface. The selected surface should allow the belt to be pierced through, but at the same time be hard enough. A spring mattress will do.

Holding the belt with your fingers on both sides, pierce the belt. The needle enters strictly vertically. Now you will need nail scissors with thin sharp ends or a clerical knife. Using a knife or scissors, carefully expand the hole to the width through which the belt tongue will pass.

The main problem with homemade holes is that when the tongue passes through the hole from the bottom up, it pulls the material along with it. We need to make the hole have a conical shape. To do this, fold the belt in half so that the hole is on the fold itself. Trim the edges carefully. It is necessary to bend the belt along, then across, then in different directions obliquely.

Your tool must be very sharp so that you can accurately cut off very small pieces of material. Periodically check the width of the resulting hole. It is very easy to get carried away and cut off the excess.

The hole is made a little smaller than necessary for the free passage of the tongue. It will develop quickly. No leather strap further action do not need to do. Hole in belt synthetic material need to melt around the edges. So you prevent peeling of the outer and inner decorative layers of the material.

Heat the awl or needle on the sole of the iron, with which the hole was first made. The temperature of the iron is about 200 degrees. Carefully run along the edges, as if sealing them. The needle cools quickly, so you won't be able to melt the edges too much. But you do not need to press the needle, especially at the first moment after removing it from the iron.

In the described way, you will make a hole in the belt that will last a long time and will not differ in any way from others already on it.

Buying belts and other accessories an exciting activity but sometimes there are disappointments. You meet a chic belt, and the length is excessively large, and it can not be worn in this form.

There is a lot of advice on the internet. Craftsmen offer to disassemble the antenna from an old TV or radio and choose a tube of a suitable diameter. Next, insert the antenna into electric drill and drill a hole.

With this approach, the holes really turn out to be perfectly even, but rare girl wants to do all this, and even at home there may not be an old antenna, because not everyone is so thrifty to store a lot of old things. Therefore, you will have to give the belt to the workshop or do a little easier.

How to shorten a leather belt and make neat holes?

There is a lot of advice on the Internet. Craftsmen offer to disassemble the antenna from an old TV or radio and choose a tube of a suitable diameter. Next, insert the antenna into an electric drill and drill a hole.

With this approach, the holes really turn out to be perfectly even, but a rare girl wants to do all this, and there may not be an old antenna at home, because not everyone is so thrifty to store a lot of old things. Therefore, you will have to give the belt to the workshop or do a little easier.

If you want to shorten the belt with your own hands, buy a belt with a collapsible buckle, where it is enough to unscrew the special screw. Each girl can adjust such a belt to fit her volumes. It is enough to take measurements, disassemble the buckle, cut off the excess from the belt web and make a hole for the screw.

Someone punches a hole with a nail or awl. Some women's sites advise exactly this way - to punch new holes in the belt with an awl or a nail! It's no good. The hole must be drilled with an electric drill. No tubes from old antennas are required, just take a sharp wood drill. The hole will turn out perfectly round, just the edges will not be perfectly smooth, as from drilling with a tube. Only completely smooth edges are not important to us, in any case, the hole will be hidden.

I think everyone knows that an electric drill is a simple and affordable tool that should be in any home. At the same time, we must not forget the safety precautions and take into account that the drill can wind our hair if they are nearby, and in addition, it is important to put a wooden block of sufficient thickness so that during the drilling process we do not damage the floors or the table where we will drill our belt.

Even if there is no real man in your house, you should have an electric drill anyway. With the help of a drill, any woman can hang a new cornice, a picture or a panel, it is actually very simple and interesting.

This advice applies to collapsible belts, but there are models where the buckle is stitched or pierced with rivets. How to proceed in this case? The easiest way is to make additional holes in the belt. But this is not the best solution.

Even if you can make perfect holes, taking into account all the indents and sizes, the belt will still remain long and its end will have to be wrapped around the waist, which is not very stylish and beautiful, and also visually adds volume. Therefore, it is better to give the stitched belt to the masters, so that they open the firmware, shorten the belt and then re-sew it.

In conclusion, it is important to note that most belts from fashion brands are sewn or made in such a way that it is impossible to shorten them without ruining them at all.

Categories

Popular