Mats univ p15 ursa. Technical characteristics of various types of ursa heaters (ursa). Fiberglass insulation URSA GEO

Lightweight and resilient material designed for structural applications pitched roofs, partitions and frame walls at a step load-bearing elements 600 mm. The shape and geometric dimensions allow the installation of plates by one person.

The main difference between URSA GLASSWOOI P-15(G) boards and URSA GLASSWOOI M-15(G) mats is the shape and dimensions, which allow:

• isolate, without reducing the layer thickness, internal and external interfaces of structures at angles close to a right one;
• provide high-quality insulation of hard-to-reach places of interface structures, for example, a roof slope and a wall when insulated from the inside of the room;
• carry out work on heat and sound insulation of inclined surfaces by one person.

Specifications URSA P-15(G)

Mineral heat and sound insulation based on fiberglass. Produced using eco-technology GEO.

Elastic heat and soundproof material in the form of plates, intended for use in the construction of frame walls and partitions with a step of bearing elements of 600 mm. Recommended primarily for the professional construction segment.

Specifications

Dimensions

• Frame walls with a wooden or metal frame.
• Walls with external insulation along the frame with siding cladding.
• Frame cladding of walls and partitions.
• Walls made of framed sandwich panels.
• Soundproof frame-sheathing partitions.
• Partitions made of stones and blocks, insulation in the middle layer.
• Acoustic ceilings.

Permissible applications

• Pitched roofs with thermal insulation installed between and below the rafters.
• Thermal insulation of a balcony / loggia using mineral insulation.
• Attic floors on beams.
• Roofs made of framed sandwich panels.
• Interfloor ceilings on beams.
• Ceilings on beams over cold cellars.
• Reinforced concrete ceilings, floors on logs.
• Air duct insulation.
• Insulation of industrial equipment.
• Thermal insulation of walls of baths and saunas.
• Thermal insulation of floors of baths and saunas.
• Railway transport.
• Water transport.
• Automobile transport.
• Modular buildings (change houses).

These simple rules will help to carry out high-quality work on the insulation and soundproofing of premises and will help to avoid many mistakes when working with URSA GEO materials.

Shipping

When transporting URSA GEO, protect the material from rain, snow and possible damage. When loading into a vehicle or van, do not squeeze material packages. Also, do not over-tighten the material with lashing ropes and other transport devices. This is due to the fact that the material in the package is already in a compressed state, and additional compression can lead to a deterioration in the recoverability of its thickness. Stack packages with boards horizontally in the car body. When carrying media in a roll or bundle, do not handle the media by the open edge of the packaging at the end. This may cause premature damage to the package.

Storage

During storage, protect URSA GEO from atmospheric precipitation. Store the material in packaged form in covered, dry rooms or under a canopy. When storing outdoors under a canopy, do not lay the packages on the ground, but place them on pallets. Pack packages with boards in horizontal position, install rolls vertically (up to 3 tiers inclusive).

Unpacking

Remove material from packaging immediately before use on site. This will greatly reduce the risk of damage to the material. The packaging can be used to protect the material from contamination when laid out on the construction site or as bags for collecting construction debris.

When unpacking mats (rolls):

Open the package by cutting it sharp knife(It is recommended to start the cut from the edge of the roll, having previously made two cuts of the film at the end).

Roll out the insulation mats to their full length.

Wait 5-10 minutes or shake the rolled sheet slightly: the material should regain its nominal thickness.

Some URSA GEO mats are supplied in packs of 2, such as URSA GEO M-11 (2×50 mm). In this case, if you need to use 50 mm thick material, the mats must be separated from each other after unpacking. When unpacking the boards, simply open the package.

Mounting

When working with the material, it is recommended to wear gloves and protective clothing; when laying material overhead, it is also recommended to wear safety goggles. These security requirements are the same for all mineral wool insulation(fiberglass, stone wool, slag wool) and serve mainly to protect against dust that occurs when working with the material. Cut the material with a sharp long knife on a hard surface. Do not use blunt blades, as this may cause the fibers to “pull out” of the material and reduce its quality.

When installing materials in the structure, follow the recommendations indicated on our website, or the recommendations of manufacturers thermal insulation systems. Only use URSA GEO grades that are recommended for use in a particular design.

The standard thickness of many URSA GEO materials is 50 mm. In this case, the required thickness of thermal insulation in the structure can be 100, 150 or 200 mm. To receive required thickness lay the material in several layers. For example, to obtain a thickness of 150 mm, you can lay a material with a thickness of 50 mm in 3 layers. To find out what thickness of thermal insulation is needed, you can use our calculator.

When installing, install insulating materials tightly to each other and to the base. When laying slabs in several layers, it is recommended to place the slab joints with an overlap - so that the slab of the next layer overlaps the junction of the plates of the previous layer by at least 10 cm. This will avoid through cracks and “cold bridges”. When installed in a frame, the width of the material should be 1-2 cm greater than the distance between the elements of the frame in the light. Then the material is held in frame structure due to the forces of elastic spacer arising from the compression of fiberglass.

Final work

After completion of work and before removing material waste, spray the work site with water. This will reduce the amount of dust in the air during cleaning. Cleaning is best done with a vacuum cleaner. To collect waste material and other construction debris, you can use the packaging remaining from the insulation.

Ursa P-15 is a stable, easily recoverable form after compression and bending, no delamination and crumbling, good insulating qualities.
Insulation plates are cut with a width of 600 mm, which facilitates the use of the material when laying it in standard frames. They seek to buy Ursa P-15, if necessary, for example, to insulate the attic or floor, and the distance between the rafters / lags is 580-600 mm along the axes. Also, such mineral wool is often taken to insulate the facade for siding, blockhouse and other types of hinged cladding. The use of fiberglass for thermal insulation involves working with gloves and protective mask. However, the choice in favor of the technologically advanced Ursa P-15 minimizes inconvenience in work, since the plates have a stable shape, do not generate dust, and are clearly cut.

Consumer Benefits

• Comfortable transportation. The packaging is compressed by about half, which allows economical use of the volume vehicle during transportation.
• Fast cutting. Plates can be cut with an ordinary construction or clerical knife.
• Small specific gravity. Transportation and installation do not cause difficulties. The ability to carry out installation by one person without assistance.

Technical advantages

• Provides excellent thermal insulation object. Choice of plate thicknesses of 50 and 100 mm is available. If necessary, you can mount the mineral wool in two layers. Plate length - 1000 mm.
• Together with thermal insulation properties the house receives protection from street noise. The insulated surface maintains vapor permeability.
• The material does not burn (group NG, KM0).
• Has water protection "Water Guard".
• The manufacturer guarantees compliance with environmental standards.

In terms of cost, Ursa P-15 is a competitive insulation, and with high quality characteristics ensure its demand among professionals.