Instructions on how to assemble a sliding wardrobe with your own hands. Photo report and visual video. Step-by-step instructions for assembling a wardrobe We measure the diagonal and nail the back wall

Hello again. Today we will assemble our wardrobe, we will do this according to the instructions below.

So, we took the parts from the cut. We ourselves did not want to glue the edge, so we ordered gluing in the same place, especially since the price of gluing is not so big.

We also bought all the necessary fittings for the cabinet and the necessary fasteners.

The floor turned out to be not quite even, so the cabinet had to be made not on a plinth, but on adjustable legs; accordingly, the detailing was also slightly redone.

The introductory part is over, let's start assembling.

Instructions for assembling the wardrobe

The procedure for assembling the wardrobe will be as follows.

You need to start assembling from the bottom of the cabinet, namely from assembling the base and installing the legs.

We take the part, which is called the bottom, and mark its underside for the installation of the base and legs as shown in the diagram below:

The plinth can be fixed to the bottom with the help of mini fixes (eccentrics, rastexes - whoever calls it), confirmations or ordinary plastic corners.

Since this will still be an invisible zone, and the cabinet will not stand on the plinth, but on legs, I decided to fix the plinth with plastic corners. I fixed the legs with screws 3.5 * 30.

Only when you screw the legs - do not overdo it (you can twist it, and the sharp part of the screw will come out from the back).

We fasten the four parts of the base to each other with the help of confirmations. For your convenience, take angle clamp. You can use .

Do not twist the corners of the front plinth, as you have to remove it to adjust the legs.

We will fasten the sides to the bottom and roof with minifixes. They are great for fastening perpendicular parts, and they also manage to completely hide the fastener.

If space permits, it is convenient to assemble the sliding wardrobe lying on the front and fasten it with the help of confirmations. But since I didn't have a room free space, I had to assemble it while standing, and use eccentrics (rastexes, minifixes) as fasteners.

At the bottom and on the roof of the cabinet (on the inside) we mark the holes for installing the minifix rod.

Before installing the sidewalls, using a level, the bottom of the wardrobe must be leveled as evenly as possible. Just lean on the level and adjust the legs to the maximum horizontal position.

Now you need to mark the sidewalls, the holes must exactly match the installed rods on the bottom and roof. In the sidewalls, you will need to do two different drillings in two different planes.

The first hole is made under the metal eccentric, which will tighten the stem, it is done during inside sidewalls, with a special cutter 15mm, at a distance from the end edge to the center 34mm (this is if the stem has a total length of 44mm, like mine).

In general, when landing a part on a rod, its head should look out by 6 mm. If you are installing minifixes for the first time, practice better on rough parts, so you will feel more confident when assembling.

The second hole is made at the end of the part, with a 6-6.5 mm drill, strictly in the center (8 mm from the edge).

For a more detailed understanding of this assembly step, you can use our materials on.

When you've done everything required holes, do not rush to immediately install the sidewalls and the roof.
To give the structure initial rigidity, immediately assemble the central partition with the upper shelf (we fix it with confirmations).
In the next step, we need to plant the sidewalls, back wall consoles and the assembled T-shaped partition on the lower rods, tighten with eccentrics, and fix the upper shelf to the sidewalls (confirmations). Use an angle clamp for support.
Next, we fix the roof, and check the verticality with the help of a level.
If everything is fine, to ensure additional rigidity, we install additional shelves with the help of confirmations.
Now, with 3.5 * 16 screws we fasten the back wall of the fiberboard. We start from the top two corners, and after perfect alignment we begin to screw in the screws throughout the box, in increments of 15-20mm. You should also fix the fiberboard to the central partition and the top shelf.

The most hard part work is finished. We put the cabinet in its place, once again check the position of the cabinet in terms of level and proceed with the installation of shelves, hangers and drawers.

Shelves can be made both rigid (secured with confirmations) and removable (on shelf holders).

In order to have fewer hole plugs on the visible side of the closet, I decided to install the shelves on the shelf supports.

Everything is simple here. On the sidewall we mark the desired height, with a 4.5-5 mm drill we make NOT a through hole, up to 8 mm deep and hammer the shelf support there.

If you by purchasing closet, decided to save money on furniture assemblers, then this article with detailed instructions and some secrets will help you assemble a closet without the mistakes that beginners usually make. We hope that this article will save you not only time for assembly and disassembly, but also your expensive nerves. Sliding wardrobes have different designs, and how to assemble them may differ slightly. We offer you the most common and common wardrobe, assembly instruction which will help during the assembly of other models.

Wardrobe assembly tool

To assemble the wardrobe, you need a screwdriver, a screwdriver, a set of hex keys, a tape measure, and a clerical knife. Sliding wardrobe with three doors sliding shelves and a hanger bar Cabinet plinth assembly There are two types of wardrobes, in some the plinth is screwed to the body separately, in others side walls are the basis of the plinth and are connected by a longitudinal planochka-plinth. This cabinet has a separate plinth, which is assembled using Minifixes(furniture corners).

The indent should be the same on all sides.
Make sure the corners are 90 degrees. Usually furniture makers use self-tapping screws with a size of 4 * 16. Sometimes the plinth can be screwed a little closer to the front side, if you have a room wide plinth. We nail the support legs to the base. Sometimes the manufacturer completes the cabinet with adjustable legs, with which the level of the cabinet is adjusted.
Cabinets are assembled for convenience mainly in a lying position, so it is recommended to provide enough space for mounting the cabinet in advance.

Assembling the cabinet body

Follow the enclosed instructions carefully. All parts and fasteners have their own designation. It is very important not to confuse the body parts, which at first glance are the same and may differ by only two or three holes. Otherwise, when the cabinet is almost assembled, you will have to disassemble it again and put the parts in their place. Lay the pieces of the side walls parallel. Important! Be careful not to confuse the top and bottom of the parts, as well as the front side with the back. Front side always has an edge, the back can have a groove for the back wall of fiberboard.

This cabinet is also assembled with furniture fasteners Rafix. A part that looks like a minifix, but has a plastic case. We screw the rods from the rafixes into the holes intended for them and tighten them with an eccentric. Be careful until the cabinet body is assembled and the back wall is installed, all fastenings can be easily break out. Do not skew cabinet parts, keep even corners. Installing the rear wall of the cabinet. After the cabinet body is assembled, the connections are tightened, it is necessary to turn the cabinet over and lay it face down. In order not to scratch the front of the cabinet, it is advisable to put cardboard or a rag under it. You can use cabinet packaging.

Cabinet Diagonal

Before fixing the wall of the cabinet, you need to set the diagonal so that all corners of the cabinet are 90 degrees. To do this, you need to measure the two diagonals of the cabinet with a tape measure. They must be equal in length (See the diagram). Some cabinets do not have a groove for the back wall and it is simply nailed to the end. It is better to use self-tapping screws or a stapler with long hardened staples. Since the wall usually consists of two or more parts, a connecting strip is provided at the junctions. If there is none, then it is better to fasten it to the internal parts with a stapler, since the thickness of the chipboard body is 16 or 18 mm, when you screw two parts of the fiberboard to it, you only have 9 mm left. stock. It is easy to miss with a self-tapping screw and go past the end of the part, where the back wall is connected and screwed.
Now the cabinet can be placed. Lifting is best done with an assistant. It's easier and safer that way. When the cabinet is installed in its place, you can mount the shelves. For this, either shelf holders, or corners, or rafiks are provided. We screw the rods of the raffixes into the sockets under them and lower the shelf on top of them. It's easier to start the installation with upper shelves.
We fasten the roller guides. Self-tapping screws should not protrude so as not to interfere with the course of the rollers.
Insert into guides assembled crates. They should slide out easily without rubbing. We fasten the flanges for the rod. Usually there is a markup for self-tapping screws. If not, then it is necessary to step back from above 7-10 cm, enough to be able to hang hangers.

Installation of wardrobe doors

Now that the cabinet is almost assembled, it remains to install the doors. It is desirable to pre-adjust the level of the cabinet. Otherwise, the doors will not close tightly.
To install the top rail, you need to drill at least 5 holes for self-tapping screws, two on each side and one in the middle. The guide should be aligned with the edge of the cabinet lid.
To install the lower guide, it is also necessary to drill three holes with a diameter of 4 mm, and chamfer with a larger diameter drill so that the head of the self-tapping screw is flush with the guide. Sliding wardrobe guides different manufacturers require a different indentation of the edge of the cabinet. To simplify the installation, you can simply put the guide on the installation site, and fix it when the doors are installed.
Installing the door in the rails. First, the upper rollers are inserted into the upper guide and raised to the stop, then the lower rollers are inserted.
First, two side doors are inserted into the second track, then the middle door into the first track.
The doors are adjusted with a hex wrench (sometimes with a “cross” screwdriver). When correctly set, the door should fit snugly against both walls of the cabinet.
Now you can glue the sealing brushes. First, the protective film is removed. Attention, after removal protective film It is not recommended to touch the place where the brush will be glued with your hands. Oily fingerprints will make the brushes stick worse.

In recent years, sliding wardrobes are becoming increasingly popular. They are compact and convenient for storing all the things you need in everyday life. Behind the sliding door hides not only clothes, but also shoes, accessories and even the necessary Appliances. This allows you to save a lot of space in your room due to rational use every inch of your room.

The sliding wardrobe can be installed not only in the bedroom, but also in the living room or corridor. It does not take up much space, so it can even fit in an apartment. small sizes. All these characteristics are relevant for a simple and inexpensive wardrobe Basya, which will be discussed in this article.

Characteristics and features

This closet is great for those who are on a slightly tight budget and are looking for inexpensive wardrobe compact sizes. This model costs two or even three times cheaper than its counterparts, but it also looks good and lasts no less. It is available in several basic colors, so you can choose for yourself a cabinet that will perfectly fit into any interior you choose. The closet is spacious enough, so you can fold and hang in it not only things from your basic wardrobe, but also what you don’t wear or don’t use at the moment.

The only drawback that almost all buyers note is the difficulty in assembling it. More precisely, the lack of a simple and clear instructions, which explains in detail how and in what sequence to assemble Basya's wardrobe.

How to mount

The easiest way to deal with all the complexities of installing Basya wardrobe is to entrust this process to professionals. But, if you do not want to spend extra money, or are simply used to doing everything yourself, then you can try to mount your furniture on your own.

This process begins with the installation of the frame. All structural details are marked with a special number, which is also indicated on the drawing. The assembly of the wardrobe body begins from the bottom corner. To do this, one of the side walls is attached to the bottom. A parallel wall is installed nearby. The installation is completed by fixing the roof.

When the frame is ready, you can nail the back wall to the base. Chipboard sheets fastened with self-tapping screws. They begin to fix from above and fall down. It is necessary to fix the back wall both from the outside and from the inside. After completing this process, it is advisable to check whether all the parts are evenly fixed - an installation error can significantly reduce the life of the cabinet.

Having fixed the main parts, you can fix individual shelves inside the cabinet. To fix five shelves, you will need self-tapping screws, wooden dowels, glue and drill. The main tip to remember when installing shelves is to start at the top and work your way down. When installing shelves, pay attention to the fact that their front edge is in front, and not rough raw edges.

The hardest part is installing the door. The sliding mechanism of the closet door must be installed so that the door opens and closes well. It depends on how correctly the mechanism is installed, how convenient it will be for you to use the closet. All rollers and fixing elements are included with the main parts. In addition, there is also a mirror for the facade on a film basis. Finally, after all these procedures, close all visible holes with decorative plugs that come with the kit and check the build quality.

Each apartment must have such a multifunctional piece of furniture as a wardrobe. It will save space in your home and organize the space. Not everyone can afford to buy it due to various circumstances. This is not a reason to refuse such a thing. A jack of all trades, it will not be difficult to make and assemble it yourself.

Of course, some knowledge is required. There is nothing complicated here, as it seems at first glance. In addition, what joy and pride you will experience from the work done. After all, furniture assemblers charge a fairly high fee, and you can handle it on your own.

After the decision to buy a closet has been made, it becomes necessary to correctly assemble it.

To assemble the purchased furniture, you need to follow the cabinet assembly instructions supplied by the manufacturer. There are certain rules. Following them, you will assemble any item of high quality and in a short time.

You should not take everything out of the packages at once, especially mix parts from different packs. Follow the sequence.
Read the instructions carefully so that later there are no overlays and you do not have to redo it again.
Make sure the hardware and component in place. Otherwise, you will not be able to fully assemble the furniture. Handles must match the color scheme. It is necessary that the guides for drawers have a soft stroke.
Assemble one section at a time. You need to start from the bottom, gradually moving to the sides.
Open the package, lay out the parts, prepare the tools.
Mirrors, glasses are installed at the final stage. This is how you avoid damage.

For assembly, you need a screwdriver, screwdriver, hex key, tape measure.

If you yourself are engaged in manufacturing, then it will be much easier to assemble.

It is very important to follow the assembly sequence, otherwise you will be forced to disassemble and reassemble the cabinet in the correct sequence.

How to work with laminated chipboard - a popular material for cabinet furniture

Currently, in the manufacture of furniture, chipboard is mainly used. This is the fundamental. Represents wood chips large dispersion. By hot pressing, it is shaped into a sheet. In the manufacture of plates, formaldehyde resins are used, they are an additional component. Difference from simple chipboard consists in covering with a film made of paper and melamine resin. According to environmental indicators, it is better to use class E1 materials. Chipboard boards have good compaction, thanks to which the furniture made from them is strong, has long term services.

Fastening the rail on the cabinet door

If you think that this material has the same composition, then you are mistaken. By coating they are divided into veneered, rough and laminated. According to the composition of quality, they can be divided into three grades: the first - they use first-class sawdust (usually a tree of the same species). The surface is flawless, not a single chip. The plate is decorated, laminated with a film or veneer. The second grade - you can already see small defects. Facing may or may not be. Third - there are already tangible defects. Such plates are not covered by anything.

While the cabinet is not completely assembled, make sure that the attached parts do not tilt, as the fasteners can be broken out.

In addition, chipboard is moisture resistant and fireproof (withstand high temperatures). They are mainly used to make a furniture body, but they are also used in the production of partitions or used as interior decoration. It is worth mentioning that chipboard, due to its composition, perfectly holds nails and self-tapping screws.

In order to stiffen the closet, it is necessary to fix the back wall.

The main “steps” for assembling do-it-yourself wardrobes are indicated in the instructions.

Furniture from these plates has many advantages compared to other materials.

Acceptable prices.
No manufacturing difficulties.
Q factor.
Significant period of use.
Diversity colors and decorations. This will help to perfectly match the furniture in the living room, kitchen or children's room.
Perfectly harmonizes with other materials.

Such furniture looks great in any interior.

Another important chipboard feature- these plates have heat and sound insulation. Therefore, they can sheathe the walls of the room.

Make sure that the holes for the shelves and the hanger rod mounts match the holes on the opposite rack.

Also, if you started a redevelopment of an apartment / house, knowing how to assemble a wardrobe yourself will help you quickly and easily solve the issue of moving this furniture.

What tools are needed

Significant costs in the acquisition of the tool will not be required. To collect kitchen set, closet or hallway, you need to have the usual set of tools: a screwdriver, a hex key for confirmation, a screwdriver, various drills, a bit for confirmation, an awl, a pencil, a tape measure, a square, fine-grained sandpaper, electric drill, stationery knife, iron, joint knife, rubber mallet, retainer for details.

The distance between opposite corners should be the same.

Assembling a wardrobe with your own hands is quite easy and everyone can do it simply by using the instructions.

It is unrealistic to guess what tool you will need to assemble furniture. It depends on whether the project is difficult or not.

Now you need to install the wardrobe doors.

To open the closet, you do not need to remove chairs or move other furniture.

Preparation before assembly

First you need to prepare the room. The final outcome of the case depends on this, how much time you spend on work. Important point- so that nothing interferes. Make sure all materials and necessary tools are at hand.

As a depth limiter, you can use a plastic dowel 6 or 8 mounted on a drill.

With the help of a sliding wardrobe, you visually separate different zones in the room, for example, working from the recreation area.

Assembling furniture at first glance seems to be a simple matter. Many people make mistakes, as a result of which defects appear: the doors and sashes are weakly adjacent, when the doors are opened, they can creak, due to misalignment of the holes, the parts are skewed, the furniture is unreliable on the floor. To avoid this, you must follow certain rules and instructions.

Built-in wardrobes of various models, made from natural and artificial materials, are very popular in interior design.

Some models of the closet are able to transform to the features of the room: the presence of a corridor, recesses in the wall, where you can put the closet.

Basic assembly steps

The assembly of the wardrobe is carried out strictly according to the scheme, vertically or horizontally. The second option is better, so you can prevent skew of the parts to be joined. If the ceiling height does not allow to raise ready cabinet, then work is best done in an upright position.

You will be able to assemble a wardrobe of the "compartment" type with your own hands if you follow the step-by-step instructions.

In such a closet, you can put twice as many clothes, while not at the expense of the enormity of the furniture itself.

First of all, you need to attach the base and adjustable legs to the bottom. They are necessary if the floor is uneven. Next, we proceed to the assembly of the body. We connect the sides to the base. To make the structure strong, we attach an intermediate rack and a shelf. This is necessary so that the sidewalls do not roll. After we fasten the remaining parts, attach the cover. It is advisable not to nail the back wall, but to screw it onto self-tapping screws. At this stage, we put the cabinet in its place. We install guides for drawers, holders for shelves, a bar for hangers. Check that the drawers should slide out smoothly.

You need to familiarize yourself with all the details of the product (so as not to confuse anything during the assembly process and not have to start all over again), prepare the tools and the place where the assembly and installation will take place.

This job will take a lot of your time.

Next up is the installation of the doors. First we fix the guides, then we fix the rail on the screws. We insert the doors, check that they open and close smoothly. Correct them if necessary. Lastly, we glue the sealing brushes. We attach plugs to the holes of the confirmations.

As a rule, sliding wardrobes, like all furniture, are assembled in the lying position of the cabinet.

Do not skew cabinet parts, keep even corners.

Summing up, we can say that the assembly of the wardrobe is not the same hard work. Your desire, skill and ability will make it easy.

After you have done everything, be sure to check how the doors work (whether they creak, move freely, etc.), how shelves and other details are firmly fixed.

Be careful until the cabinet body is assembled and the back wall is installed, all fasteners can be easily broken out.

VIDEO: Do-it-yourself wardrobe. How to assemble a closet?

Sliding wardrobe - a universal piece of furniture. It can compactly accommodate a lot of things, leaving free usable area apartments. The only negative: the assembly of a wardrobe from master furniture makers is expensive. However, you can save money - assemble a wardrobe with your own hands.

Choosing a place and measuring the area under the wardrobe

Before proceeding with the installation of the structure, it is recommended that a novice master, firstly, arm himself with instructions and watch training videos on the topic: how to assemble a wardrobe at home. Secondly, choose the right place for the closet and draw a diagram future design. The thing is that the furniture is made with perfectly even corners. Floors may be uneven. Therefore, in order to avoid warping the cabinet, arm yourself with a water level, plumb line or square and select appropriate place.

Using a tape measure, take measurements and apply on a sheet of paper. Construction flaws in details that are not visually visible on paper will become noticeable (if any). Be sure to measure the distance between the walls at the bottom and top of the cabinet. In the end, you should get an approximate diagram.

Cabinet assembly: step by step instructions

Instructions for assembling the wardrobe will allow you to perform high-quality installation work even for a beginner. Before starting work, prepare the necessary accessories:

shelf-toucans - 12 pcs.,
adjustable legs - 6 pcs.,
sliding system for doors
pipe Fi25 for hangers,
rod flanges - 4 pcs.,
mortise handles - 4 pcs.

For fastening the frame, shelves, doors:

universal screws (3x16 and 3.5x30),
plastic corners(20 pcs.),
confirmations (6.4x50 - 100 pcs.),
confirmation plugs (50 pcs.),
stops and restraints.

To install the wardrobe yourself, you will need the following tools:

a set of screwdrivers (cross-shaped and straight);
imbus key,
cord plumb,
level,
pliers,
a hammer,
screwdriver,
roulette,
stationery knife.

Step one: installing the base

The assembly of the wardrobe begins with the installation of the base, namely the base and legs. We take a part, which is called the base, and make drawings on it.

We fix the base with the help of confirmations. Since this zone will not fall into the field of view, the cabinet is on legs, and not on the plinth, you can use plastic corners. We fasten the legs with screws 3.5x30.

4 parts of the base are also fastened together with confirmations.

Step Two: Assembling the Case

Having assembled the base of the cabinet at home, proceed to the installation of the body - sidewalls, partitions, roofs.

We fix the side walls with confirmations.
We fix the back wall with screws (no need to nail).
We install vertical piers and a roof on confirmations.
We fasten the cross ties in each section separately, at different levels. Thus, it will be possible to provide the necessary rigidity over the entire height of the structure. In the center we will install one continuous unifying screed.

It is very important to correctly install the stiffeners. Otherwise, the cabinet may wobble. The role of stiffeners will be performed by transverse ties together with the back wall of the cabinet.

Step Three: Install Shelves

As a rule, even for beginners, assembling shelves does not cause difficulties. Shelves are located in separate sections. There are several ways to attach them:

With an axial arrangement of the shelves, you should put a corner furniture coupler. It will connect the horizontal plane of the shelf with the vertical intermediate wall. In order not to break the symmetry, install corner ties on each side of the central axis of the mounting wall.
Fastening the shelves with a "helicopter" - along the central wall of the cabinet. This method belongs to the category of non-standard. First you need to take one shelf and fix it in the center on the confirmation, turning it 90 ° along the axis. Attach the next shelf to 2 confirmations. Then return the previous shelf to its original position and reinforce it with tightening furniture corners.

If you want to have removable shelves, you do not need to fix them with confirmations. Install the "shelf supports" and insert the shelves. In this case, there is one great advantage– absence of plugs from the holes on the visible side of the cabinet.

To install the shelf supports, make drawings on the inside, clearly defining the height of the shelves (make sure that even corners are maintained), make non-through holes with a 4.5 mm drill. The depth of the holes must not exceed 8 mm. It is recommended to use a drilling depth limiter, if there is none, a plastic dowel for 6 or 8, which is installed on the drill. Hammer the shelf supports into the holes.

Step four is the most important

Most milestone in the installation of a sliding wardrobe - installation of doors. The door leaf must be level.

The work steps are as follows:

Install a door guide rail into the top opening of the cabinet. You need to fix it with screws.
Drill holes for the screws in the bottom profile.
Place a stopper on each end of the guide rail. Stoppers will fix the doorway in the closed position.
Insert the bottom profile inside the cabinet and screw it to the bottom.
put in place sliding door closet. Upper door rollers insert carefully into the upper profile and the lower wheels into the recess in the lower guide profile.
Adjust the doors to each side of the cabinet. This should be done when they are in the closed position. Adjust the wheels located on both sides of the door leaf. Adjust the left one along the left side surface of the cabinet, the right one, respectively, along the right side.
Making sure that door leafs correctly aligned, open and close freely, no pulling, fix the lower guide rail with screws.

At the end of the cabinet assembly, stick on each door rubber gasket to dampen the shock that occurs when opening and closing them. If you follow all the recommendations on how to assemble a wardrobe, you can outside help easy and quick to carry out all installation work.

Categories

Popular