How to remove the film from the sun from the glass. How to clean a window from a sun-protection film. Soap solution and old newspapers

Last years summer is quite hot. And if the windows of your apartment face sunny side, and there is no way to put the air conditioner in, the room quickly becomes very hot. I want to hide from the sun somehow.

Therefore, solar control film, which is glued to windows, has become so popular so that the room is cooler. I also put sun protection film on the windows in the living room. And I did everything according to the instructions. But when it came time to remove it, aluminum traces remained on the glass, the same color as the sun-protection film. The lowest layer of the film seems to have “grown” into the glass. I'm not talking about the fact that the sun-protection film was generally difficult to remove from the window. For several days I "fought" with these traces, no matter what solvents I used. There was no result at all. I already thought that the glass would have to be changed, until one specialist told me how to remove traces of sun protective film.

The fact is that the sun-protection film is made of lavsan, which does not come into contact with solvents at all. That is why their use to remove these traces will not bring results. You don't even need to test your nerves.

How can I remove sunscreen marks?

Imagine using Fairy, my favorite dishwashing liquid. And also a new stationery knife helped me. With a sponge, I applied Fairy to the glass. And then sharp with the side of the blade of a clerical knife, she scraped off traces of sun-protection film.

I will not say that this procedure was not laborious. It still took me a lot of time and effort, the film was rubbed off a little bit, but now the window is like new, clean - clean, not a single trace is left.

How to remove sunscreen marks easily

I noticed that in sunny weather, when the glass heats up, it becomes easier to remove the traces of the sun-protection film. Better to use new sharp blade. If you feel that it has become dull, then use a dense cloth to break off the tip of a clerical knife.

Never again will I stick solar control film directly on the glass itself. You can fix it on the frame with adhesive tape without removing the protective layer from the film. Or you can hang the sun protection film as a curtain.

The Forum recommends the use of stove cleaners, they speak especially well of a product called Shumanit. You can try it if you have it on hand. Only when working with this product, you must wear protective gloves, and also avoid contact of this product with plastic parts frames.
If this contact is difficult to avoid, cover the frames with thick tape. I after removing the traces of the sunscreen just remove it.

Since there are traces of aluminum left on the glass, it would be logical to try to remove them with a product that can cope with this metal. You can try to remove these traces with an alkaline agent.

My advice to you on how to remove traces of sun control film is to generally refuse to use this film by gluing it directly to the glass if after a certain period of time you need to remove it. Unfortunately, manufacturers of sunscreen film did not write exactly this way in the instructions for its use.

The profile of a plastic window is covered with a special film that protects it from dirt, scratches and other mechanical damage during delivery and installation. It is very easy to remove it from the product, but it must be done in time. It is advisable to start this immediately after the installation of the window. Otherwise, it will be necessary to resort to more radical methods of cleaning the film from the profile.

Why is it difficult to clean the protective film from the window

The instructions for plastic windows usually indicate that the film must be removed within 2 weeks after installation. Removing the film will not cause much difficulty in the coming months. However, if it remains on the profile for more than 4 months, it will take a lot of effort to remove the film.

What could be the reasons for this problem? The film in its composition has several layers, which are attached to the profile using a special adhesive. Strong adhesion to plastic occurs under the influence of solar radiation, as well as heat. In other words, the process of decomposition of the inner very thin layer of the film takes place. Therefore, the inner layer is much more difficult to remove than the surface.

Reasons that contribute to strengthening the bonding of the film and PVC frame:

heat action. AT summer time the film dries to the frame much faster than in winter;
the quality of the special adhesive applied to the film affects the complexity of its removal. The cheaper the windows, the lower the quality of the glue;
exposure to UV rays. The adhesive layer of the film on the windows located on south side buildings, may dry out faster. Therefore, it is more difficult to remove the film on such windows than on windows located on the north side.

How to remove film and adhesive tape from metal-plastic windows

It is recommended to remove the protective film from the window within 2 weeks after installation. Then it will be difficult to do so. This is due to the fact that under the influence of various factors, its adhesive layer will change its characteristics. You may need to seek help from a cleaning company or wipe off the old tape yourself using tools and substances such as:

scraper;
building hair dryer;
scissors;
Cosmofen;
different chemicals.

If a duct tape does not come off completely, then you should use alcohol or tape.

Methods for removing adhesive tape from the glass of plastic windows

There are many methods for removing adhesive tape from double-glazed windows. However, the fastest and most effective ways, thanks to which the entire film is removed and the window surface is not damaged, are the following:

scraper or brush. Tape removal with this tool will never damage the window surface when used along with soapy water;
an eraser that will need to scrub the film intensively enough. But at the same time, the surface of the profile is well preserved;
construction dryer - the best remedy, but one condition must be met when using it. You can direct the hair dryer only at the frame. If a jet of hot air hits a double-glazed window, it may crack or burst from exposure to temperature. A building hair dryer heats up the tape, after which the glue begins to dissolve, which means you can easily remove it;

Advice. With absence building hair dryer you can always use the usual one, only it should work in turbo mode. But do not forget that this option is suitable if the protective film is not very strongly adhered to the PVC profile.

white spirit can also be useful in removing the adhesive film from the product, but it is usually applied not on top of the PVC window, but between the film and the surface of the product. It is necessary to pry off its edge and moisten the place with white spirit. Wait a few minutes and remove the film;
Kosmofen perfectly eliminates the film. This tool has proven itself as a cleaner for plastic windows;
thin knife. Use such a tool carefully, because if you press it hard, you can scratch the window profile. In this case, the actions should be as follows: with a knife, you need to pick up a small edge of the film, then tear it off very slowly. Residues of glue are removed with a solvent;
wide tape will help remove the remaining adhesive tape. It is very easy to use it. It is necessary to stick the adhesive tape on the surface and carefully remove it along with the remnants of the film;
technical alcohol or denatured alcohol must be poured into a small spray bottle and the substance is evenly sprayed onto the protective film. Denatured alcohol should be left for a few minutes on the surface. Then pry off the edge of the film with a knife and remove the film. In this way, the entire profile is sprayed, and the remaining film is removed. Glue is removed with acrylic solvent;
Shumanit. The effectiveness of this detergent, which is produced in Israel by Buggy, has been proven by numerous consumer reviews. And since this strong remedy, then it must be used with extreme caution;
RP-6 is an excellent film remover that should be thickly applied to the frame surface for 10 minutes. The film swells and easily leaves after the use of this drug;
a weak solvent well eliminates traces of PVC films. However, remember that before you apply the tool on the entire surface, you need to check its effect on an inconspicuous area of \u200b\u200bthe window.

Attention! It is worth saying that the options listed above are always applicable for all details. window structures, since the adhesive used for them is the same.

How to remove solar control film or foil from a window

All modern materials that protect our homes from high outside temperature, have in their composition not only aluminum, but also other elements that complicate the process of removing them from the surface. And so that there are no noticeable spots on the glass, as well as streaks, the foil or film from the window is removed with special care. There are the most popular methods for cleaning windows from PVC film.

Steaming against old duct tape

With the help of a modern steamer, you can easily remove the film from the window. The entire cleaning process must be carried out in several stages.

A small area on the window must be heated with hot steam, which produces a steamer. At the same time, it is important that its direction be pointwise, and not over the entire area of the window.
After 5 minutes, you must lift a small section of the film, and then pull it towards you, thereby separating the film from the window.
We do the same with the new section until the entire window is clear of the sun-protection film.

This is the most elementary and most gentle option for removing the film. And even if after it there are traces on the window, then they are removed with the help of an ordinary soapy solution.

How to clean mirror film with newspaper

The sunscreen can also be removed using plain soapy water and newspaper. This work is done in several stages.

Other means and methods

Cleaning agents and detergents that can be removed adhesive tape from the window frame, suitable for removing stains and films from the glass surface. In addition to the already mentioned Cosmofen and Shumanite, effective substances such as:

Fenosol;
Domax (the preparation is intended for careful care of ceramics and glass, therefore, it does not contain abrasive substances).

But even these very powerful tools are not always up to the task. In this case, you need to use a hard scraper or choose another way to clean the window from the film.

Video: remove the stuck film with tape

Precautions for removing film residue from glass and plastic

During work to remove sunscreen or ordinary film precautions should be taken from the window. Need to use protective equipment from chemical substances, which have a negative effect not only on human skin, but also on his respiratory tract. Use sharp objects carefully so as not to get hurt. Try to follow the following rules:

work with chemicals in impervious and very durable rubber gloves;
do not press hard on the glass, as you can break it;
proceed with extreme caution when using a scraper, scissors, knife and other sharp objects so as not to scratch the window or injure yourself;
do not allow chemicals to come into contact with eyes, skin, or inhalation;
Keep tools and materials that remove film marks out of the reach of children.

In order for the result of the work on removing the film from the window to please you, adhere to the following rules:

remove the protective film immediately after the window is installed. And if installation work not yet completed, it is better to stick on the surface of the window masking tape. So you can avoid not only pollution, but also damage to the surface of the PVC profile during the repair process. Then, after completing all the work, you will not need to make great efforts to remove the stuck tape;
after removing the protective sticker, treat all moving parts of the fittings with grease;
do not use abrasive substances;
when using chemicals, take into account their level of impact on the PVC surface, otherwise one of the layers of the window can be broken at the micro level;
work carefully with sharp objects, and if possible, remove the film with your fingers so as not to leave scratches on the profile;
do not use strong solvents that can damage the profile.

Before proceeding with the removal of the film from the PVC window, it is necessary to complete all installation work. If so, great view. window opening will delight you long time. The exception is such types of work, after which you cannot physically remove the film.

At first glance, removing the film from window panes may seem like an easy task. Understanding the opposite comes when you take up this work.
AT best case waste your strength and nerves, but you can ruin the window. This article will help you avoid all this.

The first way. How to remove the film from the window glass using soaking

It will help if the film was attached to the glass with a water-soluble adhesive.
Prepare the canvas, such that it is in size on each side window glass folded over two inches.
Soak it in a solution of any dish or window cleaner, such as Fairy, Drop, Sort.
Moisten the film on the window with a cleaning solution from a spray bottle.
Press firmly against the glass. Wait about an hour. In general, the longer it is on the glass, the easier it will be to tear off the film. Just do not forget to constantly moisten the canvas, it should always remain wet.
With a fingernail (you can use any sharp object instead, a toothpick, for example), carefully pick up the film from above and peel off two centimeters from the glass. On the formed line where the film sticks to the glass, apply a singing solution. The remaining canvas must also be moistened.
Wait five or ten minutes.
Carefully separate, starting from the corner, the film from the glass. Do this smoothly, carefully so that the film does not tear. At the same time, do not forget to moisten the remaining densely.
If you have an assistant, then have him apply the cleaning solution to the fabric peel line at this time.
Do work intermittently so that the solution applied by the assistant is absorbed as much as possible.
Pieces of film that have not peeled off, most likely you will still have them. Remove them with a construction or stationery scraper.
Clean the window with any window cleaner you have.
Job is done.

Method two. How to remove film from window glass using a hair dryer

This is a more risky method. Sunscreen film is specially made so that it does its job perfectly in the hottest weather. summer days. Therefore, it will have to heat up to 50-100 degrees. A normal hair dryer is not capable of this. You need to use a builder. Glass can not withstand and burst. (And this is just before winter).
First, warm up the window with a hair dryer. The device must be kept 10-15 cm from the glass and not directed to one area for a long time.
For five seconds, direct a stream of air from a hair dryer to the upper corner of the glass. Unhook the corner of the film from the window and start slowly, carefully, so as not to tear, to separate it. If you are with an assistant, then let one of you work as a hair dryer, while the other separates the film, keeping it in a taut, tense state. The hair dryer should be 5-19 centimeters from the glass, depending on the temperature of the jet. Due to overheating, the film may deform and begin to stretch with threads.
When the film is removed, it is necessary to wash the window.

Method three. Household chemicals

The method is not easy, but, according to reviews and own experience, the most effective. Unless, of course, choose the right solvent.
It’s good if you can find out from the manufacturer of the film what he recommends for removing it. However, this does not always work out, especially if the manufacturer, for example, is from China.
You'll have to experiment on your own.
Peel off some of the film from the glass. Add a few drops of solvent with a pipette. Wait two or three minutes. If the film began to peel off and you saw a rainbow strip between it and the glass, then the solvent is working.
Be sure to check that the solvent does not spoil PVC profile. To do this, soak a cotton swab in the solvent and press it in an inconspicuous place to the profile. If the threads of the fleece stick to it, then use something else to peel the film from the window.
Especially protect the seals from the action of any solvent. If the solvent does get on it, wipe it off immediately.

What solvents to use

You can use 646 or 647, Cosmofen, Domax, Cosmofen, Fenosol. Specifically, Shumanit helped me.
Remember that solvents are very toxic substances, work with open windows, in rubber gloves and a respirator. Be sure to take the children out of the room, take out the aquarium, and remove the pets.
I don’t write how to remove the sun-protection film with a scraper or a melamine sponge. I tried to get rid of the film in this way - it did not help. Maybe someone else has a different experience though. Use only a special scraper designed for glass-ceramics, as usual, with such work, the profile is easy to scratch.

There are several ways that allow you to quickly and easily remove the sun protection film from the glass. To do this, you can use a damp cloth and a hair dryer or steamer. To carry out this procedure, you will need the following items:

clothes steamer or hair dryer, it can be both household and construction;
piece of fabric;
water bottle;
extension cord for connecting the device to the network.

It is clear that when water is used, then in frosty weather you will not be able to use this method. The length of the cord should be long enough for you to work comfortably. If a steamer is used, it is filled with water.

Before using the steamer, you need to find the edge of the film on the window and start working from it. The steamer is sent to the indicated place, while it must be kept at a distance of 5 cm from the window. Usually after a minute, and sometimes even earlier, the film begins to lag behind the glass. As soon as the corner lags behind, grab it and carefully pull it towards you. If you can't grab a corner, you can pry it off with a fingernail or a sharp object. If using a blade or utility knife, be careful not to cut yourself or scratch the window.

With the help of the steamer, remove enough of the film from the glass so that you can grab it well with your fingers. You can't pull too hard so it doesn't break. Now steam small areas and gradually remove the film from them. If you do this on previously unsteamed areas, then you most likely will not succeed. If this happens, then there will be a risk that traces of glue will remain on the glass.

So spend further work without having to put in a lot of effort. If something does not come out, additionally heat the problem area with a steamer, and roll the removed areas into a tube, otherwise they may stick to the window again. If traces of glue remain, then they are removed with a towel, this must be done until the glue has cooled down.

You can use a hair dryer instead of a steamer. If you take a building hair dryer, then be careful when heating the stack, as it generates much more heat than its household counterpart. When using a blade or knife, they must be handled carefully so as not to cut yourself or damage the glass.

Other notable methods

There are simple and affordable way how to remove the film, but its disadvantage is that it does not help in all cases. To use it, you will need soapy water, ordinary newspapers and a spray bottle.

The sequence of work will be as follows: a newspaper is placed on the glass, after which it is sprayed with soapy water. Newspapers should cover the entire surface of the glass and be moistened enough to adhere well to it.

After you do this, you need to leave everything for an hour, but at this time it is necessary to periodically moisten the newspapers so that they are constantly wet. Now try to tear off the film, it should come off quite easily, and there should be no traces of glue on the glass.

There is another way that allows you to effectively remove the film from the window. To do this, you can use a blade, a clerical knife or any other object.

With help sharp object separate the edge of the film from the glass and, helping yourself with a blade, carefully remove it. You can make cuts to remove it in strips. When using this method, there is a high risk of injury, and you can also damage the glass surface. Therefore, it is recommended to turn to this method only in extreme cases, when it is not possible to darken in more effective and safe ways.

You can use denatured alcohol, which is sprayed onto the surface of the window and after a few minutes the film is removed. If the first time you did not succeed, the procedure must be repeated. You can also remove the film using an ordinary eraser, and those residues and marks on the glass that could not be removed are wiped with white spirit, after which they are well removed.

Use of household chemicals

The use of detergents effectively helps to remove traces of sunscreen film. If you will use such a tool for the first time, you first need to try its effect on small area glass.

Be sure to protect the frame so that detergent does not get on it, so that an unpredictable reaction with plastic surface. After applying the product to problematic areas, it must be removed with a rag, while traces of glue should also be removed.

It is necessary to work with these means only in gloves, do not forget about protection of eyes and breath. Cleaning products are helpful glass-ceramic surfaces. Take a close look detergents, which you have at home: if they are designed to remove dirt from glass-ceramic surfaces, then you can safely clean glass with them.

Since there is aluminum in the composition of the solar control film that is used for windows, it is necessary to select products that will help get rid of this particular substance. If with the help household chemicals the film is not removed, you can always turn to a proven mechanical way and do all the work with a blade or other sharp object.

It must be taken into account that when using mechanical method removing the sunscreen foam, there is a high chance that scratches will remain on the glass surface. To remove them, after specified works to polish the surface of the window glass with felt, for this you can use GOI paste or diamond paste.

In the event that none of the methods brought the expected result, then the last option would be to replace the double-glazed window. Don't panic as this happens very rarely. In most cases, using one of the described methods, you can easily, quickly and effectively remove the sun protection film from the window.

Hide

Plastic windows are quite often equipped with various films that are needed to protect from the sun, make the glass more durable, and decorate. When buying an apartment, windows can be covered with such films, but they are not always needed by the new owner. In addition, if it is time to update the windows, since the films tend to become unusable, the question arises of how to remove the sun protection film from the window.

Coating removal methods

You can remove the sun protection film from the glass different ways by choosing the most convenient and affordable. This is done both mechanically and with the help of various detergents, they also use a combined approach in order to clean well.

The film can be quite useful: it has a small thickness, while making the window much stronger, it can no longer be broken simple stone. Exist different types films that help protect the double-glazed window even from strong impact, such as a shot; they are classified as protective. It will not work to remove a perforated film from glass or any other type of protective or tinting variety from the outside: an attacker will not do this, since the process takes a lot of time, effort, and attracts the attention of others. Most films are pasted with inside except for the protective one.

Knowing how to remove the film from the window glass may be required, if desired, to replace it when updating the interior, replacing a double-glazed window. Sometimes the product loses its visual appeal and needs to be updated, or the owners of the premises want to change its illumination, make the room lighter or darker. The process of removing the film is simple, does not require hiring a specialist, but it is worth considering that you will have to spend a sufficient amount of time and effort on this. You need to work carefully: in the process it is easy to damage the glass, scratch it, especially if you remove the film with hard materials such as a spatula or a coarse brush.

What should you do when you need to remove the film from the window?

When choosing a method, means, option for cleaning glass, the owners of the premises proceed from several parameters:

It is necessary not to harm the glass.
Spend as little time as possible on this.
The option should be inexpensive.
There should be no traces of glue, film residues, various contaminants on the glass.

The easiest option than to clean the glass from the sun-protection film is a spatula and fingers. Some types can be gently pry off by tearing off the edge, but this does not always work out due to the fact that the film is glued unevenly, in some places it is damaged and exfoliates.

It is quite difficult to remove the adhesive from the film from the glass. It is poorly removed with detergents, does not lend itself mechanical impact. In order to remove it, you can use white spirit or another alcohol-containing substance that can gently clean the surface. Do not use rags with coarse pile, as they can leave marks visible in the sun on the glass.

Understand , how to delete old film from plastic windows, it may be required if it is damaged, if you want to change the appearance of the window, renew the old coating that has deteriorated.

What are the methods for dismantling?

Removal methods can be divided into two - mechanical and chemical. The first allows you to remove the film from plastic windows without much money, but with the risk of scratching the glass. The second will take longer, cost more, but with the right tools, you can thoroughly clean the surface without harming it. For greater efficiency, the methods are best combined: first you need to cut off all the swollen, cracked or otherwise deteriorated film.

You can remove the film from plastic windows with your hands, then get rid of the glue with the help of substances such as COSMOFEN 10, FENOSOL. These detergents have a cheaper counterpart that you can buy at a hardware store: it's called P-12.

It will be much easier to remove the protective film from plastic windows if you heat it up with a building hair dryer before peeling it off. The heated glue becomes more viscous and allows parts of the structure to be peeled off. However, the glue itself is best removed when it cools down a bit.

Try to heat the surface evenly: the better you do it, the easier it will be to clean self-adhesive film from glass and the remains of its glue. The latter will not be easy to remove, you will need to use a solvent, a scraper and detergents. You need to act carefully, otherwise you can scratch the glass. A steam generator can help with this. With it, you can remove the stained glass film from the glass , get rid of the tinting or protective film, glue residue. If you don’t have a steam generator or a powerful hair dryer at hand, you should not try to heat it up with an iron. So the film will not be removed, but it will partially stick to the surface of the iron, which can spoil it to a large extent, and after cooling it will not be easy to tear it off the iron.

You can remove the self-adhesive film from the glass, if it is well warmed up, using a hard eraser for artists. The remains of the eraser are removed from the window easily. To do this, you need a dry sponge or rag. If there is glue left, you can apply the eraser again or use a solvent. In most hardware stores there is something to remove the film from the glass.

Before removing the film from the glass, you need to carefully study all the methods, purchase suitable detergents and tools with which you can clean the surface.

Categories

Popular