Wooden interior doors

Types and design

GOST 6629-88

State Construction Committee of the USSR

STATE STANDARD OF THE UNION OF THE SSR

Wooden interior doors

for residential and public buildings

Types and design

Wooden inner doors for dwelling and public

buildings. Types and structures

the dateintroductions 01.01.89

This standard applies to wooden internal doors for residential and public buildings, as well as for administrative and auxiliary buildings and premises of enterprises various industries National economy.

The standard does not apply to doors special purpose(including fire and soundproof) and doors made of fine wood.

1. TYPES

1.1. Doors, depending on the design, are divided into types: Mr. deaf canvases; O-glazed canvases; K-with glazed swinging canvases; U-with a continuous filler of cloths strengthened for entrances to apartments.

1.2. Doors of G and O types are made with one- and two-leaf leafs, with small-hollow (lattice) filling of canvases, with and without a threshold, with and without overlap, with lining and without lining, with and without boxes.

Type K doors are made with double-leaf leaves, with small-hollow filling of the leaves, without a threshold, without overlap, with or without lining, with frames.

Type U doors are made with single-leaf blind leafs, with a threshold, without overlap, without facings, with reinforced frames or without frames.

1.3. Doors manufactured in accordance with this standard are referred to as doors of normal moisture resistance.

1.4. The overall dimensions of the doors must correspond to those indicated in Fig. 1. Dimensions in the drawings of the standard are given for unpainted products and parts in millimeters. Dimensions of door openings are given in Appendix 1.

At the request of the consumer, it is allowed to manufacture doors of types O and K with sizes 24-12, 24-15, 24-19, as well as doors of type G with sizes 24-15, 24-19 with a height of 2071 mm.

It is allowed to manufacture double-leaf doors of types G and O with canvases unequal in width.

1.5. Set up the following structure symbol(brands) of doors:

Legend Examples

Glazed single-leaf door for an opening with a height of 21 and a width of 10 dm, right, with a threshold:

DO21-10P GOST 6629-88

The same, deaf two-field for an opening 24 dm high and 15 dm wide, left, with a threshold:

DG24-15LP GOST 6629-88

The same, with swinging canvases for an opening with a height of 24 and a width of 19 dm:

DK24-19 GOST 6629-88

The same, reinforced, with a continuous filling of the canvas, for an opening 21 dm high and 9 dm wide, right:

DU21-9 GOST 6629-88

The leaf of a frameless door of type G, single-leaf for an opening with a height of 20 and a width of 7 dm, left, with a lap:

PG20-7LN GOST 6629-88

2. CONSTRUCTION

2.1. Doors must be manufactured in accordance with the requirements of GOST 475 and this standard according to working drawings approved in the prescribed manner.

2.2. The design, shape and dimensions of the doors must correspond to those indicated in Fig. 2, and the dimensions of the sections, in hell. 3.

2.3. Door leafs of type U must be made with a continuous filling of the shield with wooden laths or chipboard calibrated in thickness, as well as with the use of chipboard strips calibrated in width, laid on the edge.

Examples of filling shields door panels are given in Appendix 2.

2.4. The vertical bars of the U-type door leaf frame must have a width of at least 90 mm. It is allowed to cut the bars along the length on both sides. The depth of the slots is 5-6 mm, the width is 3-4 mm.

It is allowed to use bars with a width of 45-60 mm, glued along the side surface.

Horizontal bars of the frame must have a width of at least 45 mm and be connected in the corners with vertical ones with glue in a spike or on dowels, staples, braces.

2.5. Doors are lined with materials in accordance with GOST 475 in the part related to doors of normal moisture resistance.

2.6. Doors used to complete sanitary cabins are allowed to be manufactured with a leaf 30 mm thick and at least 1800 mm high, with a frame bar width of at least 50 mm.

2.7. Doors of types O and K are allowed to be manufactured with a frame structure with a width of frame bars of at least 100 mm.

2.8. On the lower part of the doors of type U in public buildings, at the request of the consumer, linings made of decorative paper laminate with a thickness of 1.3-2.5 mm according to GOST 9590, superhard fiberboard with a thickness of 3.2-4 mm according to GOST 4598, sheet aluminum or painted sheet steel. The width of the overlays is 220 mm.

2.9. A box without a threshold is embroidered at the bottom with a mounting board fastened with nails or spiked joints to the ends of the vertical bars.

2.10. In doors of types O and K of public buildings, protective fences are installed on both sides, examples of which are given in Appendix 3.

2.11. Doors of type U and frameless doors of types G and O must be equipped with sealing gaskets in accordance with GOST 10174 or others, providing the necessary tightness of the porches.

2.12. The location of the devices is given in Appendix 4. Doors must be supplied with selected sockets for lock bodies (latches) and holes for handles.

Door leaves for frameless doors must be supplied with the top half-hinges installed, the bottom half-hinges must be packed and supplied as a set.

2.13. Installation options for frameless doors are given in Appendix 5.

Options for boxes with PVC lining for doors of types G, O without a threshold are given in Appendix 6.

Schemes for determining the left and right doors are given in Appendix 7.

The specification of glass for doors is given in Appendix 8.

2.14. The door purchase order must specify:

the number of doors by brand and the designation of this standard;

type and color of finish;

type and thickness of glass;

instrument specification.

At the request of the consumer, it is allowed to supply door panels without boxes and boxes without panels.

Door dimensions

Notes:

1. Door schemes are shown from the opening side of the leaf.

2. The numbers above the door schemes indicate the dimensions of the openings in decimeters.

3. Dimensions in parentheses are for swing doors.

Design, shape and sizes of doors

Heck. 2 (sheet 1)

Heck. 2 (sheet 2)

Note . Sections of parts, see fig. 3.

Heck. 2 (sheet 3)

Notes:

1. Sections of parts, see fig. 3.

2. It is allowed to manufacture doors of type U with overall dimensions type G doors

1 mounting board; 2-patterned glass according to GOST 5533 or reinforced glass according to GOST 7481, or window glass according to GOST 111 4-5 mm thick

Heck. 3 (sheet 1)

Notes:

1. Sections of blind doors are similar to glazed ones, with the exception of glazing parts.

2. It is allowed to use plastic layouts for fixing glasses.

3. It is allowed to use mounting boards of a different design.

1-bars of the shield frame; 2-lining

Heck. 3 (sheet 2)

Note . The width of a double-leaf door with an average rebate without a rebate is 12 mm less than that indicated in Fig. 1 and 2.

1-loop PN9-130 according to GOST 5088; 2-window glass according to GOST 111 4-5 mm thick

Heck. 3 (sheet 3)

1-sealed gasket according to GOST 10174; 2-cladding with fiberboard grade ST or T, group A, 3.2-5 mm thick according to GOST 4598 or plywood grade FK, 4-6 mm thick, according to GOST 3916.1 or GOST 3916.2

Heck. 3 (sheet 4)

Note. It is allowed to manufacture type U doors with a frame width of 74 mm for interior doors and doors of public buildings.

APPENDIX 1
Reference

DIMENSIONS OF DOOR OPENINGS IN THE WALLS

Note. The dimensions of openings for frameless doors are set taking into account Appendix 5.

EXAMPLES OF FILLING SHIELD DOOR LEAF

1. Shield with 2. Shield with small- 3. Shield with small- 4. Shield with small-

solid hollow behind-hollow behind-hollow

filling in filling out filling out filling out

with a virgin bar-veneer of plywood or

wooden mi (slats) solid fiberboard

bars or stripes

(slats) chipboard

or half

1-spike, staple or paper clip; 2 bars for installing a lock or handles; h-clearance width, not more than 40 mm; l- clearance length, no more than 400 mm; b-shift of rails relative to each other, not less than 50 mm

Heck. 5 (sheet 1)

5. Shield with 6. Shield with fine 7. Shield with fine 8. Shield with fine

small-hollow-hollow-hollow-hole

solid wood finish wood finish

hardboard paper honeycombdried bars

niem from (option) (slats)

soft fiberboard

Heck. 5 (sheet 2)

Notes:

1. Example 1 - for a Y-type door, examples 2-7 - for a G-type door.

2. For a leaf with a height of 2300 mm, the length of the bars for installing the lock and handles is 700 mm. Installation of bars - see. example 3.

3. When lining door panels of type G with fiberboard boards 3.2 mm thick, the width of the gap between the elements of small-hollow filling should not exceed 30 mm, and the length should not exceed 200 mm.

4. Filling the blind part of the glazed sheets can be performed by analogy with examples 3-7.

Examples of installation of protective fences

1-wood planks

Note. Use of plastic, metal and wooden fences different design.

LOCATION OF INSTRUMENTS IN THE DOORS

1-loop PN1-110, PN1-85, PN2-110, PN2-85, PN3-110, PN4; 2 handles RS100, RS140, RK1, RK2, locks and latches; 3-latches ZT; 4-loops PV1-100, PV2-125 or screw and overhead hinges; manufactured according to special specifications; 5-locks ZV7A, ZV4; 6 loops PN1-130, PN1-150, PN2-130, PN3-130, PN3-150.

Notes:

1. Devices for doors must comply with GOST 5087, GOST 5088, GOST 5089, GOST 5090.

2. Types of devices for the doors of public buildings must be assigned in the projects of buildings.

3. Hinges PN9-130 are installed in swing doors according to GOST 5088.

APPENDIX 5
Reference

BOXLESS LEAF HINGE

1-wooden cork; 2-steel plate; 3-anchor; 4-mortise loop; 5-screw hinge card with nut; 6-sealing gasket

Heck. 8 (sheet 1)

1-wooden cork; 2-steel plate; 3-anchor; 4-consignment loop; 5-sealing gasket; 6-wood threshold

Heck. 8 (sheet 2)

APPENDIX 6
Reference

PVC LINED BOXES

Note. Vertical elements boxes are connected to horizontal ones using spikes and steel dowels or screws.

APPENDIX 7
Reference

SCHEMES FOR IDENTIFYING LEFT AND RIGHT DOORS

APPENDIX 8
Reference

GLASS SPECIFICATION FOR DOORS

INFORMATION DATA

1. DEVELOPED AND INTRODUCED State Committee for Civil Engineering and Architecture under the State Construction Committee of the USSR

DEVELOPERS

Yu.A.Argo, cand. tech. sciences (topic leader); I.V. Strokov; G.G. Kovalenko; Z.A. Burkova; I.I. Kiseleva; N.P.Safonov, cand. tech. sciences; V.T.Sokolova; T.S. Slastenko, cand. tech. sciences; I.F. Savchenko; O.L. Bykovsky; N.D.Popkov; N.I. Zhukov; L.V. Voronkova; G.V.Levushkin; V.S. Ruchkin; N.B. Zhukovskaya; N.V. Shvedov

2. APPROVED AND PUT INTO EFFECT by the Decree of the State building committee USSR dated 12/31/87 No. 325

3. REPLACE GOST 6629-74

4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS GOST 475-78

2.1, 2.5

GOST 3916.1-89, GOST 3916.2-89

GOST 4598-86

2.2, 2.8

GOST 5087-80

Appendix 4

GOST 5088-94

2.2 Appendix 4

GOST 5089-90

Appendix 4

GOST 5090-86

Appendix 4

GOST 5533-86

GOST 7481-78

GOST 9590-76

GOST 10174-90

2.2, 2.11

GOST 19111-77

Appendix 6

5. RE-ISSUED October 1991

LIST OF ABBREVIATIONS

including - including

fibreboard

other-other

Chipboard-chipboard

clo.-number

nominal-nominal

NTD-normative-technical documentation

off-deviation

QCD-department of technical control

prev.-limit

etc. - other

TU-technical conditions

Lv. h.p.-clean floor level

DSP-cement particle board

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the State Committee for Civil Engineering and Architecture under the Gosstroy of the USSR.
2. APPROVED AND INTRODUCED BY Decree of the State Construction Committee of the USSR of December 31, 1987 N 325
3. INSTEAD OF GOST 6629-74
4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS

1. RE-ISSUE

This standard applies to wooden internal doors for residential and public buildings, as well as for administrative and auxiliary buildings and premises of enterprises in various sectors of the national economy.

The standard does not apply to special purpose doors (including fire and soundproof doors) and doors made of fine wood.

1. TYPES

1.1. Doors, depending on the design, are divided into types:

• G - with deaf canvases;
• O - with glazed canvases;
• K - with glazed swinging canvases;
• U - with a continuous filler of cloths strengthened for entrances to apartments.

1.2. Doors of G and O types are made with one- and two-leaf leaves, with small-hollow (lattice) filling of the leaves, with and without a threshold, with and without overlap, with and without lining, with and without boxes.

Type K doors are made with double-leaf leaves, with small-hollow filling of the leaves, without a threshold, without overlap, with or without lining, with frames.

Type U doors are made with single-leaf blind leafs, with a threshold, without overlap, without facings, with reinforced frames or without frames.

1.3. Doors are classified as products of normal moisture resistance.

1.4. The overall dimensions of the doors must correspond to those indicated on the drawing 1. The dimensions on the drawings of the standard are given for unpainted products and parts in millimeters. Dimensions of door openings are given in Appendix 1.

Door dimensions

Notes:

1. Door schemes are shown from the opening side of the canvas.
2. The numbers above the door schemes indicate the dimensions of the openings in decimeters.
3. The dimensions in parentheses are for swing doors.

At the request of the consumer, it is allowed to manufacture doors of types O and K with sizes 24-12, 24-15, 24-19, as well as doors of type G with sizes 24-15, 24-19 with a height of 2071 mm.

It is allowed to manufacture double-leaf doors of types G and O with canvases unequal in width.

1.5. The following structure of the symbol (brand) of doors is established:

Examples of symbols:

Glazed single-leaf door for an opening with a height of 21 and a width of 10 dm, right, with a threshold: DO21-10P - GOST 6629-88

The same, deaf two-field for an opening 24 dm high and 15 dm wide, left, with a threshold: DG24-15LP - GOST 6629-88

The same, with swinging canvases for an opening with a height of 24 and a width of 19 dm: DK24-19 - GOST 6629-88

The same, reinforced, with a continuous filling of the canvas, for an opening 21 dm high and 9 dm wide, right: DU21-9 - GOST 6629-88

The leaf of a frameless door of type G, single-leaf for an opening with a height of 20 and a width of 7 dm, left, with a lap: PG20-7LN - GOST 6629-88

2. CONSTRUCTION

2.1. Doors must be manufactured in accordance with the requirements of GOST 475 and this standard according to working drawings approved in the prescribed manner.

2.2. The design, shape and dimensions of the doors must correspond to those indicated in drawing 2, and the dimensions of the sections - in drawing 3.

Design, shape and sizes of doors

Drawing 2 (sheet 1)

Drawing 2 (sheet 2)

Drawing 2 (sheet 3)

Notes:

1. Sections of parts, see drawing 3.

2. It is allowed to manufacture doors of type Y with overall dimensions of doors of type G.

Types O and G

Drawing 3 (sheet 1)

1 - mounting board; 2 - patterned glass according to GOST 5533 or reinforced glass according to GOST 7481, or window glass according to GOST 111 * 4-5 mm thick

______________
* On the territory of the Russian Federation, GOST 111-2001 applies, hereinafter in the text. - Database manufacturer's note.

Notes:

1. Sections of blind doors are similar to glazed ones, with the exception of glazing parts.

2. It is allowed to use plastic layouts for fixing glasses.

3. It is allowed to use mounting boards of a different design.

1 - shield frame bars; 2 - lining

Drawing 3 (sheet 2)

Note: The width of a double-leaf door with a middle rebate without a rebate is 12 mm less than that indicated in drawings 1 and 2.

Drawing 3 (sheet 3)

1 - loop PN9-130 according to GOST 5088 *; 2 - window glass 4-5 mm thick according to GOST 111

______________
* GOST 5088-2005 is valid on the territory of the Russian Federation, hereinafter in the text. - Database manufacturer's note.

Drawing 3 (sheet 4)

1 - sealing gasket according to GOST 10174; 2 - lining of fiberboard grade ST or T, group A, 3.2-5 mm thick according to GOST 4598 or waterproof plywood grade FK, 4-6 mm thick, according to GOST 3916.1 or GOST 3916.2

Note: It is allowed to manufacture type Y doors with a frame width of 74 mm for interior doors and doors of public buildings.

2.3. Door leafs of type U must be made with a continuous filling of the shield with wooden laths or chipboard calibrated in thickness, as well as with the use of chipboard strips calibrated in width, laid on the edge.

Examples of filling the door leaf panels are given in Appendix 2.

2.4. The vertical bars of the U-type door leaf frame must have a width of at least 90 mm. It is allowed to cut the bars along the length on both sides. The depth of the slots is 5-6 mm, the width is 3-4 mm.

It is allowed to use bars with a width of 45-60 mm, glued along the side surface.

Horizontal bars of the frame must have a width of at least 45 mm and be connected in the corners with vertical bars with glue in a spike or on dowels, staples, paper clips.

2.5. Doors are lined with materials in accordance with GOST 475 in the part related to doors of normal moisture resistance.

2.6. Doors used to complete sanitary cabins are allowed to be manufactured with a leaf 30 mm thick and at least 1800 mm high, with a frame bar width of at least 50 mm.

2.7. Doors of types O and K are allowed to be manufactured with a frame structure with a width of frame bars of at least 100 mm.

2.8. On the lower part of the doors of type U in public buildings, at the request of the consumer, strips of decorative paper laminate with a thickness of 1.3-2.5 mm according to GOST 9590, superhard fiberboard with a thickness of 3.2-4 mm according to GOST 4598, sheet aluminum or painted sheet steel. The width of the overlays is 220 mm.

2.9. A box without a threshold is embroidered at the bottom with a mounting board fastened with nails or spiked joints to the ends of the vertical bars.

2.10. In doors of types O and K of public buildings, protective fences are installed on both sides, examples of which are given in Appendix 3.

2.11. Doors of type U and frameless doors of types G and O must be equipped with sealing gaskets in accordance with GOST 10174 or others that provide the necessary tightness of the porches.

2.12. The location of the devices is given in Appendix 4. Doors must be supplied with selected sockets for lock bodies (latches) and holes for handles.

Door leaves for frameless doors must be supplied with the top half-hinges installed, the bottom half-hinges must be packed and supplied as a set.

2.13. Installation options for frameless doors are given in application 5.

Variants of boxes with polyvinyl chloride lining for doors of types G, O without a threshold are given in application 6.

Schemes for determining the left and right doors are given in Annex 7.

The specification of glass for doors is given in application 8.

2.14. The door purchase order must specify:

• the number of doors by brand and the designation of this standard;
• type and color of finish;
• type and thickness of glass;
• instrument specification.

At the request of the consumer, it is allowed to supply door panels without boxes and boxes without panels.

APPENDIX 1
Reference

DIMENSIONS OF DOOR OPENINGS IN THE WALLS

Note. The dimensions of openings for frameless doors are set taking into account Appendix 5.

EXAMPLES OF FILLING SHIELD DOOR LEAF

1. Shield with continuous filling with wooden blocks (slats) or chipboard strips.	2. Shield with small-hollow filling wooden blocks(slats) or chipboard strips.	3. Shield with small-hollow veneer filling.	4. Shield with small-hollow filling made of plywood or hardboard.
Drawing 5 (sheet 1) 1 - spike, staple or paper clip; 2 - bars for installing a lock or handles; h- clearance width, not more than 40 mm; Ι - clearance length, no more than 400 mm; b- shift of rails relative to each other, not less than 50 mm
5. Shield with small-hollow filling made of soft fiberboard	6. Shield with small-hollow filling made of solid fiberboard (option)	7. Board with small-hollow filling of paper honeycombs	8. Shield with small-hollow filling with wooden blocks (slats)
Drawing 5 (sheet 2)

Notes:

1. Example 1 - for a Y-type door, examples 2-7 - for a G-type door.
2. For a leaf with a height of 2300 mm, the length of the bars for installing the lock and handles is 700 mm. Installation of bars - see example 3.
3. When lining door panels of type G with fiberboard boards 3.2 mm thick, the width of the gap between the elements of small-hollow filling should not exceed 30 mm, and the length should not exceed 200 mm.
4. Filling the blind part of the glazed sheets can be performed by analogy with examples 3-7.

INSTALLATION EXAMPLES OF SAFETY FENCES

1 - wooden planks

Note: It is allowed to use plastic, metal and wooden fences of a different design.

LOCATION OF INSTRUMENTS IN THE DOORS

1 - loops PN1-110, PN1-85, PN2-110, PN2-85, PN3-110, PN4; 2 - handles RS100, RS140, RK1, RK2, locks and latches; 3 - gate valves ZT; 4 - hinges PV1-100, PV2-125 or screw and overhead hinges; manufactured according to special specifications; 5 - locks ЗВ7А, ЗВ4; 6 - loops PN1-130, PN1-150, PN2-130, PN3-130, PN3-150.

Notes:

1. Devices for doors must comply with GOST 5087, GOST 5088, GOST 5089-2003, GOST 5090.
2. Types of devices for doors of public buildings must be assigned in building projects.
3. Hinges PN9-130 are installed in swing doors according to GOST 5088.

APPENDIX 5
Reference

BOXLESS LEAF HINGE

Drawing 8 (sheet 1)

1 - wooden cork; 2 - steel plate; 3 - anchor; 4 - mortise loop; 5 - screw hinge card with a nut; 6 - sealing gasket according to GOST 10174

Drawing 8 (sheet 2)

1 - wooden cork; 2 - steel plate; 3 - anchor; 4 - overhead loop; 5 - sealing gasket according to GOST 10174; 6 - wooden threshold

APPENDIX 6
Reference

PVC LINED BOXES

Note: The vertical elements of the box are connected to the horizontal ones using spikes and steel dowels or screws.

APPENDIX 7
Reference

SCHEMES FOR IDENTIFYING LEFT AND RIGHT DOORS

APPENDIX 8
Reference

GLASS SPECIFICATION FOR DOORS

The text of the document is verified by: official publication wooden details and wood products for construction. Part 1. Windows and doors: Sat. GOSTs. - M.: IPK Standards Publishing House, 2002