Repair of the frame fastening on rollers K2 of the MOD series. Installing rollers on the sliding wardrobe doors independently Criteria for choosing rollers for sliding systems

The rollers that are included in every wardrobe perform important functions. They align the doors and adjust their position in space. At first glance, the assembly of the mechanism seems complicated and time-consuming, but it is not. How to independently install rollers on the doors of the wardrobe, furniture makers say.

Why wardrobes are in demand

Those who have used a closet at least once in their life note its main advantages:

Varieties of rollers on the wardrobe door

The rollers mounted on the door leaf of a cabinet with a sliding system are upper and lower, depending on the place where they are fixed. Device features
the following:

1. Upper - set to reduce noise when moving along the guides. Consist of 2 wheels equipped with bearings. Outside the plane is covered with elastic rubber. They can be of different sizes. If the profile is covered with metal, experts recommend using 39 mm rollers. wooden surface requires 37mm rollers.
2. Lower parts - to a greater extent determine the life of the entire door leaf. When choosing a cabinet in a store, pay attention to whether there are pressed bearings on the products. These are the highest quality samples of rollers.

You should not buy cheap parts, they will last a little, besides, you will have to constantly repair the closet. Most often, the door opening mechanism wears out due to specks accumulated in the guides. The wheel and the roller fastening device suffer from this. Doors start to slide on flooring or on the inner plane of the guide. To avoid contamination and increase the life of parts, experts advise regularly wiping the guides from dust.

If a breakdown nevertheless occurred, a video instruction on how to replace the rollers located at the bottom of the wardrobe door will come in handy:

Preparatory stage for the installation of rollers

In order for the wardrobe doors to move freely on rollers, preparatory work must be carried out before assembly:

1. Cut the profile components according to your own calculations.
2. Make a hole with a drill outer side profile that is vertical. The indent for the upper part from the border is 8 mm, for the lower part - 42 and 8 mm. And on inside the diameter of the hole should reach 5.5 mm, and on the outer 10 mm.
3. In order not to hurt mirror surface cabinet, stick a special film.
4. Provide silicone inserts around the perimeter. The material is cut so that it does not reach the edge by 2-3 mm along the width of the sash.

Step-by-step instructions for installing a wardrobe with rollers

The first thing you have to work on is to insert the canvas into the groove of the profile. To do this, take a timber or chipboard. The horizontal profile is installed by placing the insert of a piece of furniture on the floor. Press one end of the insert into floor surface, and the second into the wall. Support the profile and the opposite edge of the door. For a tight installation of the canvas in the groove, walk with a rubber mallet.

If you notice a shift in the sealing material, dismantle the semi-dressed profile, and then place the seal in necessary place. If this is not done, the glass may be damaged the next time the doors are opened.

Now proceed to fixing the vertical components. The sash is placed on the edge. To start installing the assembly mechanism along with the rollers, you need to have self-tapping screws on hand. Roller products on the wardrobe door must be installed in the following sequence:

1. Mount the item at the top.
2. Then the bottom one.
3. Twist the profiles vertically and horizontally.
4. Armed with a self-tapping screw, place it in the upper hole. So the product is fixed in the groove. Next screw fastener until the end. How to understand that the installation was carried out correctly? The self-tapping screw passes through the profile vertically and is placed in the groove of the horizontal element.
5. Install the second roller following the same pattern.

After that, pull off the horizontal and vertical profiles with self-tapping screws, focusing on the bottom of the wardrobe doors. Fasteners are led through the upper mounting holes, stepping back a distance of 42 mm. Next, paste in door structure top and bottom guide components. To adjust and achieve the ideal position of the door plane, it is recommended to use the control screws.

Choosing videos for yourself and your child is not an easy task, as it requires not only monetary costs, but also possession of thematic information about right choice, operation and repair. One of the most respected and reputable manufacturers is the Roces company, whose rollers entered the sports products market back in 1981 and continue to be in great demand among buyers.

Functional features

Each type of skiing involves a load of a different nature, therefore, the design of the rollers must be reliable in order to make the rest comfortable and safe.

Roces (rollers), types:

1. "Street" - for ordinary leisurely skiing, recreation, designed for infrequent use, convenient for those who are just starting to learn. The speed limit is 40 km/h. The number of videos for adult couples - from four pieces.
2. "Fitness" - a sports model, designed for high-speed traffic. The body and rollers are most often not designed to compensate for jumps and shocks. Wheels with a diameter of 78 ÷ 100 mm. Some models are made with a reinforced case.
3. "Freestyle" - designed for the performance of complex dance movements, convenient for riding on asphalt and indoors. The design assumes performance of movements and good maneuverability. The wheels are in line.
4. Roller skates - a special retro model, provides maximum stability and mobility, designed for dance movements. Four wheels are installed in classical style: two on the right and two on the left. Roller diameter ≈50 mm. Rigid heel counter without additional shin fixation, special colorful appearance.
5. Children's series - roller shoes are designed to adjust the length to the size of the child's foot. Comfortable, lightweight and reliable models, made of composite materials, with quick lacing and two straps.

The differences are not only in functions, but also in color solutions, Roces, skates stand out from the general background with their design, which turns sports equipment into an accessory that emphasizes the style and character of the owner.

There are different models for men, women, boys and girls to choose from.

Equipment

What is the design of roller skates?

• The soft boot comes with different composition providing protection against mechanical damage:

1. Sheathed in polypropylene or carbon fiber.
2. Comfortable, soft orthopedic lining. Made from hygroscopic material.

1. Fast - on special loops.
2. Classical - more time-consuming, but allows you to securely fasten the leg.

• Reliable thrust bars, the material of manufacture depends on the purpose of the model:

1. Aluminum.
2. Composite material.

• Mandatory ankle protection:

1. Solid high back.
2. Power belt, provides a rigid fixation of the "boots" with the frame.
3. Clasp that tightens the boot along the leg and secures the ankle joint.

Baby Roces (rollers) features

Children's sport shoes has its own characteristics that allow kids who are on skates for the first time to quickly get comfortable with the least discomfort:

• Boot with quick lacing.
• The frame is made of plastic. Feature: the Orlando model has a cast body-frame.
• Two leg straps. Can be performed:

1. Velcro and belt (Compi model).
2. On two tightening straps, with reinforced fixation of the ankle joint (rollers of the Orlando series).

The bearing has an ABEC 3 class and hardness (depending on the model) 80A, 82A.

• The case "boots" has a special polypropylene The level of protection is determined by the model.
• Adjustment by extending the rear or front.

Baby Roces, rollers: retractable system

For longer use, a two-type length adjustment system is used: the Kompi has a front part that extends, while the Orlando has a rear part.

How to spread the Roces rollers: sequence of operations.

• For the Compi model:

1. Unfasten the upper fixing belt and the lower one.
2. At the back of the bottom of the boot is the "Push" button, you need to press it.
3. While holding the button pressed, to increase the size, pull the toe of the boot towards you.

• For Orlando and Moody models:

1. Loosen the straps.
2. At the bottom of the back (“Moody” from the end, “Orlando” from the side) there is a movable mount. The lever must be lifted and rotated, which will lead to the extension of the heel back.
3. Lock the lever.

The main types of malfunctions and their elimination

Not always and not all parts of the skates can be repaired. Most common failure:

• Grinding of rollers, which leads to warping of the skate.
• Bearing wear makes movement impossible.

Minor repairs to Roces rollers can be done by yourself.

• Unscrew the fasteners of the rollers and remove them from the frame.
• Turn over so that the worn side is facing the opposite direction.
• Fasten the rollers with fasteners.
• In the event that the rollers are completely worn away, a new complete replacement kit must be purchased.

Let's go without brakes!

The purpose of the brake pad is to stop the movement of the wheels. You can also brake without using the brake, by turning your legs or squatting, as in models for babies, while the wheels wear out a lot. And yet, with sufficient driving skill, many people do without a weighting part. How to remove brake from Roces casters?

It is possible to remove it yourself only if it is not one part with the frame, by unscrewing the fixing fasteners. If there is a short frame in the kit, it is necessary to install it instead of a long one; in the absence of such, an option is possible with cutting off an extra piece with a cutting tool.

Customer opinion

In order for little athletes to do what many people are interested in, parents get Roces for them. Feedback from parents is mixed.

• Negative nature:

1. The price does not match the quality.
2. The lacing and straps do not hold the foot very well.
3. The Orlando's plastic case is impractical to use.

• Positive:

1. Well made outer part of the boot. The Orlando model with increased impact protection stands out in particular.
2. Bearings of the middle class, quite acceptable for children's videos.
3. Design.
4. Length adjustment is located in the back, with a margin of four sizes.

And what do adult skaters say about Roces skates? Reviews of adult models are also not unanimous.

• Customers disliked:

1. Price.
2. Some models have a heavy and very soft boot with poor fixation.
3. Screws from loosening during vibrations must be fixed with a special liquid.

• Pros:

1. High quality and reliable bearings.
2. Strong, well-made in models designed for increased loads.

Total

Roces products have all the characteristics to earn the attention and respect of the buyer. But still, no matter how popular the brand is, convenience and comfort are the main selection criteria. In the case of a child, it is necessary to ensure that the leg is firmly fixed and does not hang out, be sure to check the size and stability.

» »

The guides, and accordingly the rollers along which they move, are the most critical and wearable part of the sliding wardrobes. Installing rollers on wardrobe doors the procedure is responsible, and requires a competent approach.

Sliding system

The most common in sliding wardrobes is the sliding system. It includes two guides located above and below, as well as doors that move between them. Rollers are installed on the door on both sides.

The upper rollers are called stationary and fix the door, while the lower ones are working. It is on them that the door moves. Sliding door installation includes the following operations:

• - fastening in doorway top guide;
• - laying the bottom guide;
• - installation of the door itself between the guides;
• - alignment of the door due to the lower guide;
• — fastening of the lower guide;
• - after installing the last door, the stopper is installed;
• - due to the lower rollers, the position of the doors in space is adjusted.

Types of rollers

There are two types of rollers:

• - upper rollers;
• - bottom rollers

The first type of rollers consists of two wheels with bearings. From the outside, their surface is rubberized. This allows you to achieve noise reduction when moving along the guides. Depending on the type of rail profile, closed or open, different rollers are used, both in design and size.

If the profile has metal coating, 39 mm rollers are used, and if wooden, then 37 mm.

The second type of rollers is responsible for the quietness of movement and the service life of the entire system. Higher quality rollers, equipped with pressed bearings. Another purpose of these rollers is to adjust the door leaf in space.

Rollers from different manufacturers have different term services. When buying a sliding system, savings can bring you a lot of inconvenience, ranging from unpleasant sounds when opening doors to breaking them. Better buy quality products which will save you time for frequent repairs. One of the main causes of roller wear is the accumulation of specks in the guides.

How to clean?

If you periodically ride in strong dusty winds or in places where there is a lot of dust and sand, do not forget to periodically clean the bearings. To do this, remove them from the rollers and get rid of the anthers (this can be done by removing a thin half ring with a needle and shaking out the “lid” itself).

As a rule, bearing cleaning is carried out using liquids such as kerosene, gasoline or mineral spirits. The liquid must be poured into a shallow glass or cup to such a level that it can completely cover the parts. The bearings are lowered into the tank and left there for about half an hour. During this time, they should get wet. After that, you can, wearing gloves, “flounder” the bearings.

But just swimming is not enough for effective cleaning. Rinse the balls under pressure. To do this, draw the substance you are using into a syringe with a needle put on it. Run a stream of liquid on the balls themselves and in the gaps between them.

Life time

Of course, the service life of any spare part determines the conditions in which it is operated. If a rider regularly tests their skates by riding on sand, wet grass, or riding in the rain, the grease will quickly disappear from the balls. And without it, the device will soon fail.

However, if the bearings are operated in good conditions, they can serve up to five years and require no maintenance.

How do you know if a bearing needs to be replaced?

In order to understand whether it is time to change the bearing, remove the wheel from the skate and shake it in your hands. If this process is not accompanied by any sounds, then the product is in order. If a so-called rattle effect appears, the part should be replaced.

How to change a bearing?

Most often, fans of aggressive skiing have to change bearings. and landings, parts sometimes simply crumble, unable to withstand loads. Therefore, extreme roller skaters prefer cheap bearings, as they are not so pitiful.

To replace, you will first need to remove the old bearings. To do this, you can use pliers or a bolt. If you choose the second method, you will need to insert the bolt into the wheel hole and push on the bearing. If using pliers, grab the bearing itself and pull.

However, the pliers method cannot be used if you are pulling out the bearings just for lubrication. So they can be bent.

Next, you need to install one of the purchased bearings. We just put it in place of the first one. Do not be afraid if a solid effort is required to install the product. More often, new bearings are very reluctant to fit into the wheel. Next, take the screw again, put another bearing on it first, move it to the head. Then put the axle on the same bolt. Insert the screw with the parts into the wheel and push. After that, the parts will fall into place exactly.

Brake

Brakes are those parts for skates that are not present on all skates. However, if your shoes have a brake, be prepared that sooner or later you will realize the need to replace it.

Do you need a brake?

No wonder you won't need to replace or buy this roller part if you decide you don't need it. To do this, you need to understand the advantages and disadvantages of this part.

On the plus side, the stock brake helps the rider decelerate quickly and efficiently. However, there are at least three ways to stop without using this accessory.

There are a great many riders who believe that the brake is not only unnecessary, but even harmful. Their position is based on the following arguments:

• The brake won't let you ride properly. In fact, this happens only when the roller does not know how to properly transfer weight from one skate to another and “rakes” the asphalt with a brake.
• The brake will not let you ride on the road with bumps, as it will cling to every bulge. In fact, to prevent the athlete from moving with a brake, this very bulge must be quite high. As a rule, roller skaters do not take roads with such flaws.
• The brake will not allow you to perform tricks. This is true. During the performance of many tricks, the brake can interfere with the athlete and cause a fall. However, this is relevant when it comes to difficult stunts. Jumping from curbs, for example, the brake does not interfere.
• The brake is not cool. This is perhaps the most ridiculous and at the same time sad delusion. It's funny because it's false. Of the professionals, only tricksters and slalomists do not use the brake. And he really interferes with both. But it's not about being cool. But experienced freeriders and hockey players willingly use such a spare part. This fact seems sad because beginners, not having time to learn how to stand on skates normally and “raking” the ground with brakes, begin to think about the coolness of their appearance, and even spread deceptive fashion. For beginners, the brake is simply indispensable, as it is the only effective speed damper for an inexperienced skater.

Types of regular brakes

The brake is foot and manual. The foot brake is a protrusion on one of the skates (usually the right one). This ledge is located under the heel of the athlete, just behind the rear wheel of the roller.

To stop using the foot brake, the athlete pushes the leg on the skate on which he is mounted forward and lowers it to the heel.

But not so long ago, hand brakes appeared. It's over complex aggregate. It consists of a hand pedal, which the athlete holds in the palm of his hand while skating, wires and a brake shoe attached to the skate. The difference between this brake and the foot brake is that the brake shoe is movable. When rolling, it is raised high up and does not cling to the asphalt. But if the athlete starts to press the lever with his hand, the block drops and slows down. The higher the pressure, the lower the block drops and the faster the braking occurs.

However, the second type of brakes in Russia is practically not sold and because of this it is used by a few. Therefore, the topic of a regular regular brake in our country is much more relevant.

Regular brake malfunctions

stock brake - plastic part. It's far from the best durable material, therefore, breakdowns of such spare parts for rollers are a very common case.

The brake can crack or shatter if a rider lands on it after a jump or hits a ledge at speed.

But more common cause brake failure is its banal erasure. The pad may wear out with frequent use.

In any case, it is not possible to repair the brake. It's easier to just change that part.

How to choose a new brake?

It is not necessary to refer to the original manufacturer when replacing this part. Your skates may well fit other brands, which may cost less.

But do not forget to focus on the size of the wheels of your skates when buying, otherwise you risk purchasing a product that is useless to you.

Also pay attention to the size of the hole for the tie rod or pin that will attach the brake to the frame. If it is smaller than the diameter of the bolts installed on the rollers, you will additionally have to buy a new coupler or drill holes, increasing their size.

How to replace a roller brake?

It should be noted that the roller brakes consist of a holder and the block itself. When replacing, it is recommended to buy both of these parts as a kit. This will not hit your pocket hard and will extend the life of the new element.

We also make a reservation that different rollers differ from each other in their design and methods of fastening the brakes. This difference is especially noticeable when comparing children's and adult models.

In order to remove the “children's” brake, it will be enough for you to disconnect the coupler with pliers, remove it from the grooves and remove the part. In the case of adult skates, most likely, you will have to knock out the pin.

One way or another, by removing the mounts, you can remove the rear wheel and brake. After that, it will be possible to install a new product by doing all the manipulations described above in reverse order.

wheels

One of the most important parts of the entire skate can also become unusable - its wheel, which is also called the roller. This can happen due to very intensive use of the skates. The wheels may begin to wear out and lose in diameter. If they become smaller, they will probably no longer meet your needs.

The hub may also shatter. This is the weakest part of the wheel.

But more often, the issue of replacing rollers becomes acute if low-quality wheels were originally installed on them, which, for example, do not allow you to develop good speed.

In order not to change often, choose right away the wheels that are good and suitable for your riding style.

How to choose wheels?

Initially, it is worth focusing on the diameter. After all, at different styles Skating uses rollers of different sizes.

• For running, you need to buy wheels with a diameter of 90 to 110 millimeters.
• For slalom and freeskate, as well as for slides, rollers with a diameter of 70 to 75 millimeters are recommended.
• If you prefer tricks and aggressive skating, choose rollers with a diameter of 40 to 60 millimeters.

• Wheels with an extensive hub are designed for roller skating. After all, perforated plastic reduces the weight of the entire product, which has a great effect on its ability to develop speed.
• The hub is much smaller on freeskate and slalom wheels. After all, in these disciplines develop not such high speeds like when running.
• The smallest hub on wheels for tricks. It is almost impossible to notice at first glance.

Now analyze the terrain you usually ride on and understand what surfaces your skates will have to slide on.

• If you usually spend time in roller parks, ride on smooth concrete and perfectly smooth asphalt, choose wheels with a slight stiffness of 84A or even 82A.
• If your habitat is inextricably linked with bumpy and rough asphalt, choose more rigid rollers - 85A.
• For running and tricks, even more rigid products are suitable - 88A.

How to replace a wheel?

In order to replace the wheel, you need to use the hexagon, which, as a rule, comes with the rollers. Use it to unscrew the wheel axle and remove it.

If you plan on keeping your bearings, take them out of the wheel. How to do this, we told earlier. If you bought new wheels with bearings installed or just bought all new parts, then you can not disassemble the old wheels.

After that, you can install new rollers by screwing the axles with a hex.

The easy way out is to swap!

Sometimes buying new wheels can be avoided. This applies to those cases when the rollers are erased unevenly on the skate. Sometimes an athlete may notice that the wear level of the front and rear wheels is much higher than those installed in the middle. In this case, the wheels can simply be swapped.

Multiple kits

If you are going to participate in rollerskating demonstrations, you can have two sets of wheels: training and "going out". On the first you will ride every day, and on the second (probably brighter) - only during rehearsals of performances and on themselves. Just do not install more elegant wheels immediately before the performance. Give yourself a chance to ride them and feel the nuances.

Also, some riders acquire wheels for riding in the daytime and in the dark. In the second case, spectacular luminous products are used.

Top 3 wheel manufacturers

It would be useful to mention which skate manufacturers make high-quality wheels that you don’t mind spending money on.

1. seba. This is perhaps the most popular manufacturer. We put it in first place not only because of the quality of the products, but also because the products of this brand can be found in almost any specialized store. The wheels of this brand are tightly attached to the hubs and do not fly off. The hubs themselves are very strong and solid. But such rollers are quickly erased even at high rigidity.
2. City Monkey. This is not a very popular manufacturer, but it deserves the second place in our ranking. These wheels are made in China. They are very strong and almost never wear out even when skating for several hundred kilometers. We put them in second place instead of first because of the fact that you can only buy such products online, and because of the Chinese people's love for exaggeration. So, buying wheels of one diameter via the Internet, you can get products of a different, smaller size.
3. ghostson. Another Chinese manufacturer. We put this company in third place for the reason that it is even less popular than City Monkey, which means that the quality of its products can be judged by fewer reviews. However, these reviews are good. The wheels have a strong hub and good connection with her rubber part.

Clasps

The main parts of roller fasteners are made of plastic. It's no wonder they break down from time to time. After all, at frequent use any plastic part wears out quickly and becomes unusable.

Many people think that the only way to repair or replace a clasp is in a professional workshop. Someone says that a broken clasp is a reason to buy new skates.

Replacing the mount, of course, is not as easy as changing the wheel or roller brake. But we will try to describe such a process.

Mount replacement

Most often, fasteners are attached to plastic frame boots with rivets. They are very small size, between the hats it will not be possible to insert a tool in order to disconnect them. Therefore, the hats will have to grind.

To do this, you need to use a grinder. Be sure to wear goggles when using this tool.

If the plastic of the boot is soft, the studs may not have time to grind off. The plastic will melt a little and release the holders.

If the plastic of the boot is good, then you can install new bindings by pushing fresh, open rivets into the old grooves. If the plastic has melted, then you can forget about new fasteners.

However, there is still a way out. You can thread a string through the holes. The lace-up boot will no longer fool you with broken clasps.

Consumables

Speaking of spare parts, it is impossible not to mention the tools and consumables, which should be bought by a roller skater who does not want to spend a single summer day without skating.

In order to replace a failed part at any time, it is necessary not only to keep in reserve its substitute, but also various fasteners.

You may need rivets the same size as the ones on the skates, a hex wrench that usually comes with skates, and pliers.

Having such a set of tools, you will be able to quickly reanimate your projectile, no matter under what conditions its “treatment” takes place.

We have tried to collect for you information about the most necessary spare parts for rollers. If you have already had to change the parts of your skates, describe the process of selecting and replacing products in the comments.

Hardware rollers in the furniture industry have gained immense popularity: today it is already difficult to imagine modern interior without sliding wardrobe, and a sofa - without wheels or furniture boxes on bare rails. Thanks to the rollers, it has become very easy to use the furniture: it is convenient to carry out routine cleaning of the premises, it is convenient to open a heavy sofa with a light effort. Thus, roller systems have greatly simplified human life. But what to do if the roller mechanism is out of order, is it possible to fix it on your own? How to choose reliable rollers for furniture and doors? The answers to these and other questions are in our article.

Choosing reliable videos

Before you go to the store for rollers, you should determine where they will be used. There are dozens of options for roller mechanisms designed only for moving furniture, the same number for doors, cabinets, drawer systems and boxes. Let's deal with the features of the choice.

Selection Criteria for Furniture Casters

Rollers for furniture fittings are the main mechanism of the sliding system. The main requirements for them are the smoothness and noiselessness of sliding when opening. Wheel rims can be made of rubber, Teflon, plastic, composites and steel. In addition, attention should be paid to the following criteria:

1. Planned load on the supports. This is the main parameter on which it depends whether the mechanisms can withstand the weight of the furniture. The strength of the rollers will depend on the material from which the supports and main components are made, the method of fastening the roller and the diameter of the wheel.

The rim of a quality roller is at least a third of its thickness.

1. Price. The products of trusted firms are an order of magnitude higher than those that have either not managed to prove themselves or have not been able to. Metal-plastic rollers have the lowest cost, but in case of breakage they are very easy to change.
2. The quality of materials. Reliable rollers have steel supports, and the plastic used in the mechanism is hard and heavy.
3. Construction quality. This criterion is no less important. Assessing the reliability of the design, you should pay attention to the presence of backlash, the strength of the connecting parts (roller axis, its fastenings).
4. Hull structure. It can be anyone, the main thing is that it fits the furniture in height, color, style.
5. Mounting method. There are a lot of mounting options: threaded pins, platforms for self-tapping screws, bushings, etc. The right way fastening will depend on design features furniture and the ability to install the mechanism you like on it.
6. Extended capabilities. In this case, you should determine whether the rollers are swivel or fixed, whether they have a stopper and the presence of several wheels, whether it is possible to remove the roller.

When choosing, do not forget about the rest, on the quality and functionality of which the performance of the videos themselves largely depends.

Selection criteria for rollers for sliding systems

Rollers for sliding doors have a fundamental difference depending on the opening system, which can be:

• Lower support. Suitable for all doors. A reinforced rail is installed at the bottom of the doors, which will take on the main weight of the door. A roller moves along the rail, also experiencing a high load. The top rail is only needed to support the door.

• Suspension. Suitable for light doors. In this case, the door is suspended by rollers from the upper rail, which takes the weight of the door. On the lower rail, the door is fixed on supports. In this case, you will need accessories for sliding door with top rollers.

When choosing rollers for a door, you should first of all focus on their supporting force, that is, on how much weight they can withstand.

When choosing videos, you need to pay attention to the following points:

1. The simplest rollers are made of plastic. Plastic is inferior to other materials in many ways: it breaks, scratches form on its surface, the shape of the wheel is deformed under the weight of the door, it slides off the rails and knocks when moving.
2. A better option involves the presence of bearings. Such systems are much more reliable, but they are not silent, and it is not so easy to repair bearings on your own.
3. The most preferred and expensive option is steel or plastic rollers coated with Teflon, or rollers with a rubber rim. The doors on them are silent when opened, slide smoothly and easily, and are easy to clean if necessary.

We repair roller mechanisms

During the operation of furniture products, the natural wear and tear of the main moving mechanisms is inevitable, among which the rollers are no exception. In most cases, you can repair or replace the wheels yourself.

Repairing door rollers

Regardless of what is broken - roller fittings for doors or wardrobes, they are repaired using a similar technology. Lower support systems are more common than suspended ones, and therefore the repair of such systems is carried out more often. The following is an instruction that allows you to understand the cause of the breakdown of this door system and remove it:

• Problem: The door moves with difficulty. Fitting rollers for compartments very often get stuck in the guides due to blockages accumulated there. In this case, the solution is simple - clean the grooves with a vacuum cleaner. If this does not help, you will need to check the rollers for dirt, dust, hair and animal hair that have accumulated on them - all this can interfere with the normal sliding of the wheels. Ignoring the problem will lead to wear and the need to replace the rollers.

• Problem: The door moves, falling through and creaking. Probably, the reason is the breakage or wear of the hardware roller. Remove the door and inspect the roller. If it is beyond repair, you will need to write down its name and article number, and then order a similar one from suppliers. If the roller has become unusable due to natural wear and tear, it is recommended to check the remaining rollers of the system - usually they start to break one by one.

In order to replace or repair the roller, you will need to remove it. How to do it? Here is the instruction:

1. The first step is to remove the buffer brush from the door (if it is a closet).
2. Under the brush, about 5 cm from the floor, there are 2 holes. The top hole hides the screw for fastening the rails (required if you want to disassemble the door frame), and the bottom hole hides the screw for removing the roller. To remove, you will have to use a hexagon.
3. When removing the roller, you need to make sure that the profiles do not disperse and the door does not skew (you can check by).
4. In the reverse order, the rollers for sliding wardrobes are inserted into place.

Repair furniture rollers for sofas, cabinets and drawers is usually not difficult, as it is simple and intuitive. How to install the rollers in the closet, you can learn from the video.