Installation of platbands on the door. Platbands for interior door structures - we put them on our own without any problems! How platbands are attached to interior doors

Platbands are a decorative element of the door structure that performs an aesthetic function. The task of these overlay strips is to create a frame that covers construction defects and gaps between the wall plane and the door frame. The installation of platbands on the door does not differ in particular technological complexity, but being the final decorative touch, it requires scrupulous accuracy and knowledge of the nuances of sawing and fastening from the performer.

Video demonstration of the installation of door frames

Types of platbands and methods of their fastening

To cash out the door frame, the owner of the bath can use molded products made of wood, MDF or plastic. Carpenters are advised to give preference to laminated or veneered MDF products or PVC platbands, which practically do not react to steam and temperature fluctuations.

Mounting material and specifics:

Wooden platbands can be installed on "liquid nails" or fastened with thin nails without caps. Hats can be cut off on their own or fastened with a construction gun that “shoots” with studs without them. When using nails with hats, the fasteners are slightly “drowned”, and the locations are masked with wax corrective pencils or acrylic sealants matched to the tone. The use of adhesives is acceptable, but will create problems if it is necessary to dismantle for cable laying or for the next repair. Liquid nails are applicable only in the case of perfectly aligned walls, otherwise there will be gaps between the casing and the wall to be finished.
Outwardly, MDF platbands are practically indistinguishable from wooden counterparts, but their fastening is carried out according to special rules. In order not to damage the planks, the guide holes for the nails are drilled on them in advance. The holes are not through, a diameter of 1-1.5 mm is preferred. MDF, just like wood, can be simply glued.
Platbands made of plastic prefer to be glued. Their cost allows you to dismantle cashing without regrets and the desire to reuse. Flexible plastic moldings can be glued to walls with minor irregularities.

Choice of cutting angle for joining

The angle is determined by the presence of a shaped relief with front side. At the disposal of home craftsmen who figure out how to install trim on doors, there are two options:

Planks with flat surface without a shaped form, it can be cut at a right angle. The same is done if the door is framed with platbands with a capital. The direction of docking can be either horizontal or vertical. Before installation, saw cuts are painted or tinted with varnish.
Embossed moldings, platbands with a rounded surface are cut down at a standard angle of 45º. This is the most common scheme that requires strict adherence to the rules and accuracy. The result of the slightest flaws will be unattractive gaps.

In order to ideally cut the workpiece at an angle, you need to stock up on a miter box and hand saw with small teeth. A flawless edge will turn out if the owner saws on trimming machine equipped with a turntable.

Features of telescopic architraves

Buyers of doors produced by a number of domestic factories are given the opportunity not to use fasteners at all when installing platbands with a patented telescopic design. The happy owners of Volkhovets or Sofya products will not need additional additions, since the correction in case of vertical deviations and in case of discrepancy between the size of the box and the width of the opening is carried out by adjusting the telescopic door frame.

Details on how to install doors with telescopic architraves, their owners will learn from the manufacturer's instructions, since each of them has its own technological schemes. A feature common to all is the presence of a protrusion-slot, which is introduced into the groove on the box. Connections are recommended to be strengthened liquid nails.

Step-by-step work technology - measurements and installation

It is recommended to start framing the doorway with platbands:

after completion of wallpapering;
when equipping doors with platbands on both sides after pasting two adjacent rooms;
before laying the plinth.

You need to start work on the side of the door structure into which the canvas opens. That is, from the side of the location of the door hinges. The reference point for measurements will be the bar that closes the box from the side where the hinges are located, since because of them the platband is not installed flush with the box. This indent should be equal on all three lines. For fastening platbands with reverse side doors do not need to be indented.

So, the order of work:

With maximum accuracy, we measure the length of the vertical bar installed next to the hinges. The distance resulting from the indent is added to the length. The point obtained as a result of measurements will be the beginning of the line along which the excess is cut off from the workpiece at an angle of 45º.
For the manufacture of the opposite casing, measurements are made in the same way, but separately. Not the fact that the distance from the floor to the required point will be equal.
Sawn planks are baited with two nails. We fix one of them at the base, the second about a meter later.
Under the unfixed upper ends of the vertical platbands, we put a blank for the upper bar. We mark on it the points required for flawless sawing at a 45-degree angle, saw off with a miter or simple mechanical saw.
We fix all three components.

Base door architraves usually rests on the floor, but sometimes a kind of bedside table-stand is placed under the door frame.

The step of installing studs or nails is determined independently. Carpenters recommend driving in galvanized or copper nails every 15 cm if lovers of slamming the door actively use it. With careful operation from an aesthetic point of view, the optimal step is 50 cm.

If the sawing angle is somewhat disturbed, gaps will inevitably appear at the joining points. Those who did not manage to avoid this due to inexperience do not need to despair. Failures can be masked with sealant. To do this, on both sides of the gap on the platbands, you need to stick a regular mounting tape. Preferably in several layers. Then fill the gap acrylic composition suitable tone.

We bring to your attention fast way accurate markup:

Correctly executed installation of platbands of interior doors guarantees considerable savings. Cash out in the same way entrance doors, however, platbands are fixed mainly only with inside, since the outer frame is already on the box. The work is not difficult, but meticulous, and without knowing the nuances, you can ruin a lot of material. By the way, carpenters advise inexperienced home craftsmen who want to become more adept in this direction to start with the most dimensional opening, so that in case of failure, the planks could frame a smaller door. Well, having received practical experience can take on complex tasks.

Cashing is selected for door leafs according to criteria such as texture, width, color. Cashiers are made from different kind materials, each with its own advantages and disadvantages. More details below.

Cashiers for interior doors are sold in large assortment, and you can purchase products in a wide variety of shapes (carved, figured, teardrop-shaped, semicircular.) It is this detail that is finishing after which the installation is complete.

Often, door manufacturers do not include platbands in the product package, and they have to be purchased additionally.

For some, this can be a serious problem, but to avoid it, just check the package. Naturally, the cost of the door model with all necessary components there will be much more bare door leaf, but you won’t have to look for a suitable element in other outlets. Platbands can be installed with your own hands, installation will not be difficult.

As for the dimensions of the door finish, the following are considered standard:

Width - 7 cm;
Thickness - 1.2 cm;
Height 190 - 235 cm.

In order to finish the door, in which there is one leaf, you need 5 cashiers. If the door has two leaves, then 6. If you need to frame only the doorway, then it will be enough to purchase only 2 strips. What are the best options for cashing out? In this case, we are talking about the material.

You can buy platbands from the canvas:

natural wood;
aluminum;
Become.

They may have decorative coating in the form of a laminated film, veneer, facing plastic, paint composition. Modern manufacturers Planks are made in various sizes, and therefore it is possible to choose them according to your preference.

What are the criteria for choosing cash on the door

It is worth installing platbands only those that are carefully selected, match the color to door leaf, easy to fasten. The types of canvases are described above, but what other features of the choice of cashiers are there?

If selected wooden model platbands, then it should be:

Well dried, so that over time it does not start to crack, rot and lose its proper appearance;
evenly colored;
No blue spots
Smooth without notches;
No knots or cracks.

Cash is a product that is not too complicated in configuration, and you can make it yourself. Before you properly mount, you should carefully prepare the finishing element. It is worth noting that the competent selection of tools and materials allows you to start everything. necessary work. First, the workpiece is cut according to the dimensions taken in advance. The calculation is done individually and you should not rely on standard parameters.

The quality of the work performed directly depends on how carefully each canvas will be processed by means of a typewriter or woodworking machine.

After the platband is made, it is polished. Namely, there should be rough grinding and manual processing. The second step is required to remove any circular scratches that remain electric typewriter. Finished platbands must be covered with a primer and antiseptic composition.

How to make door frames

Installing the cashier is not difficult, but first you need to prepare the element. You can find an unlimited variety various architraves from many manufacturers, which may differ in price, finish, shape.

However, many people prefer to install those products that will be made by themselves.

Thus, it is possible to significantly reduce the cost of repair and Finishing work and, besides, it is much easier to mount the finish according to your preferences on your own.

It is definitely worth preparing a number of tools, without which it will be impossible to make, cut or completely cut and attach the cashier to the door:

Saw, preferably manual.
A machine that can make a right angle.
Thickness gauge, which is required to create the correct thickness of the casing.
Vertical cutter.
Sander.
Square.
Ruler.
Pencil.

There are a variety of ways to fasten platbands. For example, you can cut it to size and nail it on nails, attach it with glue, stick it on liquid nails or mastic even to a corner, put capitals on self-tapping screws. Each of the presented options has its own advantages and disadvantages, which are worth familiarizing yourself with.

Proper installation of platbands for interior doors

Nailing the trim on the finishing nails is the most popular option. It has a lot of advantages. If necessary, you can easily remove the platbands. Mounting is quick and easy. To put the finish for the openings, you will need to pick up carnations, on which there is a flat and narrow hat.

The length is chosen, depending on the thickness of the casing, but on average 4 cm is chosen.

If only nails with hats were on sale at the time of purchase, then the hats can be removed with a couple of light movements if you use a side cutter. Before doing the installation of platbands, it is worthwhile to outline the location of the fasteners. A balance must be observed, or, in other words, the arrangement is carried out evenly so that there is no distortion of the structure. Experts recommend installing them at a distance of 50 cm from each other.

Liquid nails are glue sold in tubes. It is very easy to apply and can be used for any kind of architraves. It can be plastic or wooden model. Don't need any preparatory work, because it is enough just to squeeze out the composition, and press the trim to the right place on the opening between the wall and door panels. The advantages of this installation method are quite obvious, and most importantly, liquid nails dry as quickly as possible, they are as strong as possible, and even when the composition flows out of the product, it is very easy to remove it.

Self-tapping screws are simple and old way installation. It has such advantages as:

Reliability;
Strength;
Ease of installation.

The downside is that with too much impact on the canvas at the time of screwing in the screws, the canvas may crack. The place for the installation of the self-tapping screw must be marked in advance so as not to move even a couple of millimeters. This can also cause a violation of the integrity of the clypeus. Best of all, experts advise pre-drilling holes to avoid the above consequences.

There is also such a method of fastening as beaks. The advantages are an excellent proper appearance, ease of installation. The disadvantage is that they are made of MDF, and it is not only undesirable to remove them after installation, but after all, after dismantling, you can notice chips and cracks on the coating.

We select telescopic trim on the door

There are telescopic architraves on a door. They differ from the usual ones by the presence of a special ledge for easy connection with extensions and the door frame. They are used when the door frame is narrower than the thickness of the wall. Due to this special protrusion, the fastening is carried out through the longitudinal grooves in the door frame. If the installation is carried out correctly, then neither fasteners nor walls will be visible in the opening between the box and the wall.

This method of installing platbands is also:

Reliable;
Lasting;
Durable.

When making platbands on your own, you will need to make the most careful calculations so that the door has a neat and complete look. There are a number of nuances that you should definitely take into account when installing platbands. To hide fasteners in the form of nails or self-tapping screws, you can use a wax corrector or acrylic sealant the same color as the door leaf.

In order to avoid a gap at the junction of the platbands, each cut of the subsequent canvas must be created, relying on the previous element. If there is a curved wall in the room, then straight platbands will not work. What to do in such a situation? Finishing nails should be used to mount the edges of the trim. Such fasteners are invisible and they allow you to align the finish of the door frame.

If there are minor gaps, then acrylic sealant or, again, wax sealant will be required to mask them. To mask significant defects around the door frame, you can choose wide platbands of the order of 10-12 cm. It is best, in this case, to purchase platbands at custom order. Since the installation of platbands is a finishing touch, the procedure is carried out only at the end of the repair of the room.

Installation is carried out flush at the ends, and visually, it seems that the installation is carried out directly to the wall. Experts recommend choosing thin carnations with a small hat.

Do-it-yourself installation of trim for interior doors (video)

A door without platbands not only looks untidy, but it spoils the whole look of the room. They allow you to hide the edges of the wallpaper, the opening between the door frame and the wall, as well as bring completeness and aesthetics to the interior design.

All photos from the article

Cash on interior doors the thing is purely decorative, this design does not carry a special functional load. But even if you managed to install the loot clearly along the doorway, without platbands the view will be, frankly, not elegant. But do not panic, such work is quite within the power of a person who has general idea about carpentry.

Preparation and selection of materials

When going to the market or to the store, keep in mind, as a rule, an interior door is sold without platbands.

This is done for two reasons:

Firstly, such slats are not needed everywhere, for example, if the door is perpendicular to the interior partition, then on the one hand there is simply no room for such a slat;
And secondly, the price of doors without cashing will be lower, which is convenient from the point of view of advertising.

Tip: it is better to pick up the strips immediately, in place, when buying a door kit. Otherwise, the probability is too high to make a mistake with the tone of the coating.

As far as material is concerned, interior option 3 types of straps are used.

The most expensive and prestigious are wooden planks. But in this case, you should not pay attention to the lower price category. Cheap wooden planks can be poorly dried, resulting in them leading over time or cracking after shrinkage. If knots are present, then in this place the bar may crack during installation or the knot will fall out after drying;

Now common plastic lining. The quality and appearance here are quite decent, the cost is affordable. Such strips are not afraid of temperature changes, humidity and other risks. If you are not confused by the plastic itself, then you can stop at it;
But to be honest, almost half of our fellow citizens prefer veneered or, in extreme cases, laminated MDF. These strips do not deform, do not crack, and most importantly, they are 100% accurate.

Most often, nails for platbands of interior doors are taken galvanized or copper-plated. Available on the market now special nails without hats, but most craftsmen prefer to simply bite off the hats with pliers, it's faster and more profitable.

For fastening wooden planks, some prefer to use self-tapping screws. Of course, this is much more reliable, but in this case, the hats will need to be sunk into the array, and then covered with putty to match the bar so as not to spoil the look.

There is another option for planting planks on liquid nails or other adhesives. But they will hold only if the base is perfectly flat. Plus, at the slightest deformation of the wall or just on impact, the glue may not withstand.

Tip: often, most craftsmen prefer to coat the bar with liquid nails and additionally fix it with carnations.

Getting Started

As you know, the shape of the plank is figured, rectangular, teardrop-shaped and semicircular. The choice here depends on the design of the doors and the personal preferences of the owner. And if general instruction the installation is approximately the same, then with the joining of the corners, not everything is so simple.

Plank joining options

Planks can be connected at an angle of 45º or joined at the end at 90º. This is perhaps the most difficult stage of installation, especially if you decide to mount the platbands with your own hands for the first time.

In principle, nothing complicated, we insert a bar into the device and cut it through the groove at the desired angle. But if the device is old, then the grooves, as a rule, are “broken”, as a result, chips are obtained.

Tip: in order to minimize the likelihood of chips when making a cut, you need to stick a regular adhesive tape on top of the bar.

Hacksaw or cutting disc should be taken with as small a tooth as possible. Ordinary garden tools, as well as a jigsaw, it is better not to use it here. Based on experience, the easiest and most reliable way out is to use a hacksaw. Of course, you will cut a little longer, but everything will be smooth.

Trimming the platband at a right angle is certainly much easier. The whole problem is that it is only suitable for smooth planks of the correct rectangular shape or with slightly rounded edges. The principle is simple, the strips cut at 90º are joined at the end. Moreover, as a rule, the upper horizontal bar is inserted between two vertical side bars.

If the edges of the planks are slightly rounded, then end cuts you need to do it at an angle inward, so that they overlap, compensating for the rounding from above. There is another trick. You can insert a square decorative overlay into the corner, the choice of such products in the departments with furniture fittings is quite wide, the main thing is that they fit the interior of the doors and the room.

Plank installation technology

Important: cashing is one of the last stages of arranging a room; after its installation, it remains to mount only the skirting boards. If the plinth is already in place, then it must be removed. A plank installed above the baseboard will spoil the whole look.

We will consider docking at 45º, as it is the most difficult. You need to start by measuring the side bar, which borders on door hinges. Do not forget to make a tolerance for opening doors, often 3 mm is enough for this. A mark is made along the inner edge, after which it can be cut off;

Do not use the cut bar as a template for making the opposite one. Small unevenness in the floor or a barely noticeable skew of the loot will put your work in vain. Each plank is measured and cut separately;
Planks are fixed with nails in increments of 50 cm.
The upper crossbar is also cut off in turn. First, one side cut is made, after which it is applied to the loot and the place of the second cut is marked. folk wisdom about the fact that you need to measure 7 times before cutting off 1 time here it fits perfectly;

Beginning craftsmen rarely succeed in joining all the joints without gaps. Do not be discouraged, small cracks can be covered with tinting putty later.

As part of our story, one cannot fail to mention the so-called telescopic casing. It's pretty comfortable design, it is used if the thickness of the walls slightly exceeds the thickness of the bulk itself.

But here the loot must be adapted to the telescopic connection and have internal grooves. The photo shows the principle of such a design.

There is also a separate type of architraves with a capital. They differ from traditional designs in a wide stylized top bar. Figuratively speaking, the doors are obtained with an impromptu "crown". As you understand, a capital needs an appropriate entourage.

Conclusion

Often the installation of platbands does not cause any particular difficulties, the main thing here is not to rush. In the video presented in this article, you can see how professionals do it. If after that you still have questions, write them in the comments, we will be happy to help.

Door platbands are installed for one purpose, to close the gaps formed during the installation of the door frame in the opening.
Before you find the answer to the question of how to install platbands on doors, you need to understand the rules for selecting platbands and familiarize yourself with the technology of their installation.

Where to begin?

In order to install platbands on the door, you need to choose them correctly. To do this, cashing must be selected by width, texture, color.
When choosing the color of the platbands, give preference to the one with which the door leaf is also finished.
When choosing a width, try to choose platbands, the installation of which will harmoniously close all the gaps.
By the way, gaps are always formed when mounting the door frame in the doorway. You can't get away from them. It is impossible to make a box that is installed exactly in the doorway. More precisely, you can make an exact box and an opening measured to the millimeter, but the costs will be quite high. Is it necessary?
It is cheaper to close the resulting gap with platbands.
For the manufacture of platbands are used various materials.
Platbands can be made of wood, MDF board, plastic, veneered or laminated.
Let's try to figure out how to properly install the trim on the door.
The installation of cashing starts after the completion of the entire repair.
The operation of installing platbands is the finishing one and is performed with or after the installation of skirting boards. It is akin to fixing cornices, in the sense that it is carried out after all the finishing work has been completed.

Platband installation

To make the process of installing platbands understandable to everyone, we will divide it into several stages.

Preparatory stage
It is necessary to check the evenness and flatness of the walls adjacent to the doorway. With a large curvature, the walls must be leveled. And it is imperative to do so.

Attention! Aligning the walls, carefully monitor them mutual arrangement. The walls must not only be leveled, but also placed in the same plane on both sides of the opening.

Platbands can hide bumps and cracks up to 3 mm. But it will no longer be possible to close unevenness differences of more than 3 mm with the help of platbands. Knowing how to fasten cashing correctly, you can hide all the bumps and gaps.

The use of platbands not only gives the room an aesthetic appearance, but creates the completeness of the room.
The installation of platbands in importance can be compared with or nailing cornices.

The right tool

A few words about the tool used.
When installing platbands main problem is to fit the mating parts at the right angle. The platbands are installed either at a right angle, but most often at an angle of 45 °. It is best to use a miter box.

A miter saw is used to cut the material. It provides an even cut of platbands from any material.

But cheap models of machine tools have a backlash and an error, therefore, it is still preferable to use a miter box for installing platbands with your own hands From auxiliary tools you will need a pencil, ruler, square, level, plumb line.

The right choice of material for platbands

When choosing platbands, pay attention to the structure of the material.
The appearance of the platbands must match the pattern on the door. Since various materials are widely used for the manufacture of cashing: wood, plastic, MDF boards, then picking up platbands under the doors is not difficult.
Installed platbands can be covered from the outside with a laminated film, painted, varnished, glued with veneer.
Platbands are issued various shapes allowing to solve extensive design problems.

When buying, it is very important to check the architraves for curvature and curvature.

Trim installation rules

The rules are given for those who want to know how to properly install trim on interior doors.
When installing platbands, it is necessary to ensure the joining of parts without gaps.

The easiest option is the installation of platbands of a simple rectangular shape.
In the end, it is only necessary to ensure the docking at a right angle of the mating parts.

Most platbands are produced over complex shape and joins at an angle of 45°.
Attention! To ensure the required angle, it is recommended to apply special device called a stool.

Step-by-step installation of platbands
Below is step-by-step instruction how to fasten cash on interior doors.

First, the platbands are installed on the side from which the door opens towards itself.

Attention! Do not forget that it is necessary to correctly mark the left and right cuts.

Attention! The platbands are nailed, stepping back from the edge of the box by 5 mm.

Having cut the standard workpiece of the casing into two equal parts, cut down one workpiece from one edge. Attach the workpiece to the nailed casing and check the coincidence of the sawn corner. Mark the second edge of the workpiece, saw down the corner and insert the casing between the vertical casings.

We will wipe the places of deepening the nails with wax to match the color of the doors.

You have read the material on how to install platbands on interior doors, understood the principles and installation sequence, the video will tell in more detail.

But a few useful tips it won't hurt you:

1. There are telescopic architraves, which are fastened using a special slot. The slot is inserted into the groove of the extension or door frame.

2. There are cases when trims of the same size cannot be used because the trim cannot be adjusted in width. In this case, it is not recommended to cut the platbands in width by more than ¾.

3. The top trim is installed after fixing the two vertical trims.

4. The construction market offers architraves of various shapes: figured, semicircular, carved or teardrop-shaped.

standard sizes

W×T×H; where W-width, T-thickness, H-height. 7x1x210.

A few words about the capital

Capitals are called special door trims, the main function of which is to decorate doors.
Such platbands are made of MDF or wood sheets. The installation of capitals makes the doors rich and finished.

Once again about fastening platbands

It was described above how to fasten cash on interior doors, with the help of which related materials. But that's not all.

Platbands can be fastened not only with nails.
Liquid nails, self-tapping screws are used to fasten the platbands. There are also special mounts, called "beaks".

The use of finishing nails allows you to subsequently dismantle and replace the trim. Nails should have a flat, narrow head. The length of the nails should be 1.5 cm longer than the thickness of the casing, as a rule, 4 cm. The fastening spacing with the help of nails is recommended to be 0.5 m.

Liquid nails are called glue, designed for fastening platbands. Glue is applied to the casing, which is pressed against door frame, held for a few seconds. This method of fastening eliminates traces of fastening.

The platbands are playing decorative role, giving the doorway a complete look. The slats differ in the material of manufacture, shape, color, as well as the method of fastening. The installation of trims for interior doors is carried out after the completion of the walls, but before laying the floor plinth.

To properly install trim on interior doors, you must first select suitable items. First of all, pay attention to the material of manufacture:

Products made from natural wood are considered universal. Planks can be painted to match the color of the doors. fasten wooden elements nails without caps. If the walls are well aligned with the door frame, the platbands are planted on an adhesive - “liquid nails”.

Laminated slats from MDF appearance remind natural wood. decorative elements choose the color of the door. The platbands are fastened with adhesive or nails without hats, having previously drilled non-through holes.

PVC cashing is more suitable for plastic doors. The strips are glued or planted on the mounting profile.

There are also aluminum and steel cashing, but they are usually placed on the front doors.

Most planks are given a standard flat, rounded or shaped form.

By fastening method cashing can be consignment note or telescopic. The first type of elements is fixed directly to the door frame. The second is equipped with mounting grooves.

Tools for the job

In order for the installation of door platbands to be successful, the tool is prepared in advance.

For accurate marking you will need pencil, tape measure, plumb line, square and level.
It will help to cut the workpiece perfectly evenly at an angle of 45 degrees miter box about.
It's better to cut planks miter saw . If not available, you can use hacksaw for metal. Small blade teeth will not leave chips on the product.
For hammering nails or tapping cashing elements, they are used a hammer.

How to cut the trim?

After marking the angle of the cut and the length of the workpiece, the trim is cut with a miter saw. A feature of the power tool is adjustable table, which is set at the desired angle. In order to saw off the trim on the door correctly and without chips, the side edges of the workpiece are pressed tightly against the stops on the bed. If there is a gap, the cut will be uneven.

In the absence of an electric saw, a miter box will help to cut the edge of the casing at 45 degrees. It is better to buy a quality tool. A cheap one made of plastic has deformed thrust elements that distort the size of the corner. A hacksaw for cutting is used with fine teeth that do not leave chips.

How to fix platbands on interior doors?

A simple fastening of flat platbands is performed at an angle of 90 degrees. Vertical strips are tightly joined at the top with horizontal. When mounting wooden or MDF elements of complex shape, the ends are washed down at an angle of 45 degrees. There are 4 methods for fixing slats.

With finishing nails

Wooden or MDF door trim is easier to nail with flat heads. The fastening is reliable, and if necessary, the strips can be easily dismantled. You can use nails of a different configuration, and so that the hats are not visible, they are removed with side cutters. The length of the finishing nails for platbands is about 40 mm. The size can be calculated individually, taking into account the thickness of the cashing. After passing through the lath, the nail must enter at least 20 mm into the body of the door frame.

Attachment points are marked on the workpieces, observing the same distance. Usually adhere to a step of 500 mm. According to the marking, through holes are drilled, with a diameter corresponding to the thickness of the nail. After docking with the door frame, the platbands are carefully nailed. Hats for aesthetics are painted over with a wax pencil.

liquid nails

To fasten cashing to interior doors without nails, an adhesive is used - liquid nails. The advantage of the method is the absence of a visible place of fixation. The downside is weak fastening, as well as inconvenience during dismantling. In addition, liquid nails are applicable only if the adjacent walls are perfectly even.

Platbands are being installed on the door after sawing and trying on blanks. The bar is lubricated with back side adhesive and firmly pressed against the wall. To glue the platbands for interior doors, it is enough to hold each plank in a pressed state for no more than a minute.

Fastening with self-tapping screws

The method is similar to fixing with finishing nails, but instead of them, wood screws 25 mm long and 6 mm thick are used. Places for holes with a pitch of 500 mm are marked on the workpiece. A drill of the same diameter or with a margin of 1 mm is used.

It is desirable to drown the hats in the body of the plank. On the front side of the workpiece, the hole is expanded with a drill of a larger diameter to a depth of 1–1.5 mm. Now it remains to attach the platbands to the interior doors with self-tapping screws. It is necessary to tighten the hardware so that the hat enters the recess. The place of fixation is painted over with a wax pencil.

Fastening with beaks

The method does not require the use of screws, nails or adhesives. Cashing is equipped with a lock shaped like a beak. The connecting spike is inserted into the recess on the box and pressed until a click is formed.

The advantage of the method is the ease of installation and the invisibility of the attachment point. The negative point is the delamination of platbands from MDF during dismantling. Over time, spontaneous destruction of the joints can be observed, which requires additional processing glue connections.

How to install platbands on interior doors?

When installing interior doors with your own hands, glue, nails or self-tapping screws are used to fasten trim made of wood or MDF. However, take into account the evenness of the walls and the shape of the planks. There must be no gaps at the joints. If the walls adjacent to the end of the door frame are uneven, then it is better to refuse gluing.

Installation of cashing begins on the side where the interior door opens. This is due to the presence of loops that prevent the plank from being flush with the box element. You will need to make the same indentation, and on all three sides for symmetry. Where there are no loops, there is no need for a mandatory indent.

If the door is in a corner, the installation is done with the letter L. If desired, you can saw the element vertically and use a narrow bar.

The platband on one side is installed when the slopes on the other side are ennobled with tiles or other wall materials.

Docking at an angle of 45

When it is required to install platbands on the door at an angle of 45 degrees, a miter box is used for marking. Such a docking of elements is usually used for curly and rounded planks. In the absence of a miter box, marking can be done with a protractor.

The installation procedure consists of the following steps:

Docking at an angle of 90

Fastening of platbands at 90 degrees is carried out with horizontal or vertical seams. The choice depends on the preference of the owner. When installing the door cashing with your own hands at a right angle, blanks are used only in a flat shape. Places of cuts are treated with varnish or acrylic-based paint.

To put platbands on interior doors, with imitation of a lintel, the upper element is lengthened. Docking is obtained at an angle of 90 degrees with horizontal seams. The top bar protrudes beyond the vertical.

Telescopic architraves

Telescopic architraves are fixed to interior doors without nails. Decorative elements are equipped with a special lock consisting of a slot and a groove. Fixation occurs to the end of the box. Basic requirement correct installation platbands is the presence of a ledge. It is formed when the door frame is narrower than the thickness of the interior partition. Adjacent walls must be even, otherwise you will get an ugly gap.

Installation instructions for plastic trim

Glue is used very rarely, the connection is unreliable. Mostly plastic architraves put on interior doors using a profile. This installation method consists of the following steps:

If plastic cashing is placed on a wall lined with clapboard, then along the perimeter doorway a wooden rail is fixed, and a profile is already attached to it.

Can be installed using special nipples and self-tapping screws.

Elimination of defects

An unpleasant moment is the visibility of the head of a nail or self-tapping screw. They are slightly recessed in the body of the cashing, and covered with sealant on top desired color. You can use a wax corrector.

On the uneven walls due to the curvature of the wooden planks, the joints diverge. During installation, the joining elements are additionally connected with a finishing nail.

Wide slats from 100 to 120 mm help to hide large defects around the door frame.

How to dock a plinth with a platband?

The door trim does not need to be cut, it should reach the floor. Otherwise, it will not look very nice.

The plinth itself is customized, the method depends on the material.

Plastic ones have decorative plugs, with which you can neatly and beautifully dock the end of the plinth and the door trim.

A 45-degree cut is made on the wooden one to align the adjacent side of the plinth with the thickness of the door trim.

Dismantling

Removal of platbands is usually required when there is a change of cashing. There is no need to worry about their safety, but the work is done carefully. Picking up an ax sharp blade and a hammer, proceed to dismantle:

The procedure must be carried out carefully so that there are no dents on the door frame. Instead of an ax, homemade sharpened strips of durable metal or other similar devices will do.

Categories

Popular