How to degrease the seam between the bathroom and the tiles. Bathtub edging tape - seal the seams easily

The design of the junction of the bath and the wall performs not only decorative, but also quite pragmatic functions. Water will seep through a poorly sealed gap and serve as a breeding ground for the fungus. Careful sealing of the bath around the perimeter is necessary so that dampness does not accumulate under it.

How to seal a bath: choosing a method

Depending on the material wall decor and the size of the gap between the bathroom and the wall to seal it, you can use:

• self-adhesive border tape;
• silicone sealant;
• tiled fugue (grout);
• decorative border made of plastic or ceramics.

All options are fairly easy to independent implementation. But the final decision on how best to seal the bath can only be made by the owner. After all, the question is not only reliability, but also aesthetics.

Bathtub sealing with self-adhesive tape

The border tape is specially designed for decoration in wet bathrooms. It is made of polyethylene, one side of which is covered with waterproof glue.

Before gluing the bath to the wall should be cleaned and degreased. Then cut the border to the required length. The protective strip from the adhesive layer should be torn off gradually, and not all at once from the cut piece.

Important! The shelf life of the adhesive composition is strictly limited; if the packaging is not properly stored and the packaging is damaged, the adhesive layer begins to collapse. For a long time such a tape in the bathroom will not last.

Using Silicone Sealant to Seal a Bathtub

The sealant is sold in ready-to-use tubes and tubes, which will require a mounting gun. It should be borne in mind that in this way it is possible to seal the gap only up to one and a half centimeters thick.

The composition must be applied in an even, uninterrupted line on a degreased surface, which must be absolutely dry, otherwise the silicone simply will not stick to it. After application, the line is “smoothed” dipped in liquid soap finger.

Sealing joints in the bathroom with grout

Tile grout, also known as a fugue, is a dry mixture of white cement with additives from polymers and antiseptics. It can not only rub tile joints, but also to easily seal the bath, however, only gaps of no more than 5 mm.

It is applied to the seam between the bathroom and the wall with a small rubber spatula. To prevent the side and tiles from getting dirty with the mixture, you should glue them with masking tape.

Closing the gap between the wall and the bathroom with a decorative border

Sealing the bath can be done with a plastic or ceramic border. Depending on the thickness of the gap, its size is selected, and conventional adhesives for ceramics and plastic are suitable for gluing.

When choosing how to seal the bath, which method to prefer, you need to think carefully. Of course, much depends on the width of the gap. But silicone sealant will provide optimal protection, and the ceramic border is more aesthetic. It is best to combine both of these options, and in order for everything to work out the first time, you need to watch the video instruction for working with various sealants.

Sealing joints and seams of all surfaces is milestone repair bathroom. If moisture constantly seeps into the walls and onto the floor, this will lead to the appearance of harmful microorganisms on them. In addition, leaks to the lower floors will become possible.

In our article, we will consider all the methods by which a do-it-yourself bath can be sealed.

Note! First of all, the sealing method depends on the distance between the wall and the bath, as well as on what kind of finish you used on a particular surface.

Grouting tiled joints

If the joints around the perimeter of the bath are small - up to 0.5 cm, you can seal them with a special grout for tiles - a fugue. You can use both white composition, and add color to it to match the color facing materials premises.

In addition, ready-made colored grouts are also on sale. It is worth noting that in the bathroom it is necessary to use a special fugue designed for pools and wet rooms i.e. waterproof. So that the composition does not change its color from dirt and rust, you can additionally process the joints with a special gloss.

By the same principle, sealing the floor in the bathroom can be carried out if ceramic tiles act as its finishing coating.

Application of moisture resistant sealant

With gaps between the wall and the bathroom, as well as the sink up to 1.5 cm, you can use a sanitary moisture-resistant bathroom sealant to seal them.

It would be best if you purchase a silicone or silicone-acrylic composition designed for wet rooms.

It can be transparent, white or colored, according to your taste.

The packaging of the material can be a tube or a cartridge.

Under the latter, you will have to purchase a special pistol.

It should be noted that it will cost quite inexpensively, while pistol sealants are of better quality than in tubes.

• "Moment", German company Henkel;
• "Titan", the Polish company Selena;
• "Delta" and "Tiger", the German concern Den Braven;
• Wepost, Sazi's Russian company.

It should be said separately that if sealing is necessary acrylic bath, then this will require special composition for polymeric surfaces.

• Clean the sides of the bathtub from traces of dirt and dampness. Following this, thoroughly dry them, as well as the walls adjacent to them.
• Next, the processed joints must be degreased with a solvent.
• In order to make the seam even, define its boundaries by sticking a paper masking tape which can then be removed.
• Next, cut off the tip of the spout from the tube or cartridge to the required depth. The diameter of the resulting hole, as well as the angle of cut, will determine the width of the seam. For example, by making a sharp corner, you will get a neat and thin joint.
• Next comes directly sealing the seam between the bathroom and the wall. Insert the cartridge into the gun (in the case of a tube, no preliminary action is required) and get to work. Press down on the tube or gun handle smoothly and evenly to get a continuous and even seam along the perimeter.
• To spread and smooth the silicone, dip your finger in soapy water and walk them along the joints.

Sealant Calculator

A simple calculator looks like this:

Ceramic tile plinth

If the gap is large enough - 2/3 cm, then the bathroom can be sealed using ceramic skirting boards.

There are three options for how to do this.

• For this purpose, you can purchase special ceramic borders used as skirting boards.
• A good option is to use friezes from the same tile set that was used for wall cladding.
• And finally, the cheapest, but also the most labor-intensive and hard way- cut skirting boards from tiles.

If the gap is very large so that the mortar does not fall through when laying tiles in the bathroom, you can blow it out before starting to work with polyurethane construction foam. Glue the tiles on a regular cement-sand mortar, placing them at an angle of 45.

By the way, in the same way, you can close up the joints between the walls and the floor in the bathroom.

Plastic corners, skirting boards and borders

Sealing bathtubs can also be carried out using plastic corners used in PVC installation panels or plastic skirting boards with rubberized edges. You can glue them on "liquid nails".

Note!

This option is convenient in that it can be used both for wall cladding and for subsequent repairs to the premises.

Another plus is that the plastic is elastic, as a result, it compensates for all the movements of the bath, inevitable during its operation.

It is best to use corners or skirting boards over joints that have been pretreated with sealant. If the plastic peels off, the silicone will prevent water from leaking in.

On sale there are also special plastic borders for bathtubs. They are installed in the same way as skirting boards.

Sealing self-adhesive tape

Another way to seal acrylic bath or metal is to use special tape. The material has different width and is designed for various sizes of the gap between the walls and the plumbing fixture.

The tape must be glued strictly according to the attached instructions, otherwise it can quickly peel off. To prevent this from happening, you can play it safe and stick it on a sealant, or “liquid nails”.

Apply silicone or glue to the joint and immediately press the tape to it. Next, remove excess adhesive.

What to do if the bathroom floor is wooden

If you need to seal the joints in a bathroom with wooden floors, use a special joint sealant for wood. It has a high stretch ratio, so it compensates for contractions and expansions of the coating. In addition, such sealants allow the wood to "breathe".

Similar materials are available in a wide range of color scheme, so you can easily find the right one for your wood species.

As you can see, when renovating a bathtub, sealing can be done in many ways. You just have to: choose the method that suits your case, purchase necessary materials and boldly get to work.

Excessive humidity is the main negative factor affecting appearance and the duration of operation of the finish and plumbing fixtures in the bathroom. Despite the fact that special sustainable materials are used for repairs in this room, designed taking into account the peculiarities of its microclimate, moisture seeping into the smallest gaps leads to accelerated wear of the finish, the appearance of fungus, and an unpleasant odor.

To minimize the impact of water, the joints between the bath and the wall are completely sealed with silicone sealants, ceramic or plastic corners. Significantly simplify the process of sealing gaps can be a special curb tape for the bath, equipped with an adhesive layer.

Reasons for use

The main condition for the absence of excess moisture is the thorough sealing of all seams and gaps into which water can seep. Often gaps remain when installing the bathroom close to the walls of the room due to a mismatch between the size of the model and the room. To seal this seam, depending on its width, silicone sealant, curb tape, ceramic or plastic corner, moisture resistant solution. If you leave the seams unspecified, then the following unpleasant consequences will occur in the bathroom:

Note! Mold on the seams and wall cladding in the bathroom is not just a cosmetic defect that spoils the appearance of the room, it is a serious violation. sanitary norms. The spores spread by the fungus enter the lungs of a person, making it difficult to breathe, causing allergic reactions.

Device

It's called border tape. special agent for sealing seams, which is a long strip on polymer base impregnated on one side with butyl adhesive. It is sold in the form of rolls up to 3 meters long. One package of such a sealant is enough to seal the seams between the bathroom and the walls. Curb self-adhesive tape has the following properties:

Important! Self-adhesive tape for sealing joints between the bathroom and the wall is used only if the width of the seam does not exceed 5-6 cm. If the gap between the surfaces is larger, then it makes sense to seal it with a moisture-resistant gap or a ceramic corner.

Advantages

Bathtub tape has become a cheaper and more practical alternative to ceramic corners, which are used to seal the seams between the wall and the edge of the bathtub. The polymer sealant is perfectly adapted to the conditions of the bathroom, it effectively fights against the penetration of water into the smallest gaps. The advantages of this method of sealing joints are:

Please note that this method of sealing joints in the bathroom also has a disadvantage, the main of which is considered to be low resistance to acid-containing plumbing cleaners. In addition, the sealing tape has a fairly short service life. Manufacturers give only a one-year warranty for this category of goods, but with careful use, it can last up to 5 years.

Varieties

Manufacturers offer enough a large assortment sealants for the bathroom, because the quality of sealing depends to a greater extent on the correct selection of the tape for specific conditions. The following classifications of borders for grouting are distinguished:

Technology of use

Using a tape border to waterproof seams in a bathroom is quite simple. Even a person without construction experience can cope with this task. In addition, when using self-adhesive models, installation does not require additional tools or materials. The sealant is glued according to the following technologies:

Please note that after gluing the tape for waterproofing the joints in the bathroom, it is better not to use water for a day so that the glue adheres properly to the surface of the tile and the fixation becomes reliable.

Video instruction