Universal security system. It has best attitude prices to functionality. The radio path, operating in the new permitted free band of 868 MHz, provides a high communication range in urban environments. Dialog code provides the highest degree burglary protection.
The system combines maximum security properties(7 independent security zones) and a wide range of service options (4 additional control channels). Key fob with display displays messages in Russian and has a wide range of additional functions, has direct location main control buttons modern design and a chrome-plated metal insert for attaching keys.
Specifications:
Number of additional channels 4
Silent security yes
Number of inputs hood/trunk 1
Arming with deactivation of sensors yes
Shock sensor two-zone remote
No volume sensor
Emergency disarm Programmable code
Separate door unlocking yes
Remote start no
Turbo timer yes
LCD/LED liquid crystal
Control code type Interactive
Engine running guard yes
External interlock relay #2 normally open
vibration alert yes
Removal / arming with different buttons yes
Remote control range 900
Paging range 1200
No built-in lockout relay
External interlock relay #1 normally closed
Central locking control Power
Keyfob Display Options/ Backlight Monochrome LCD
Radio signal modulation type AM/AM
Carrier frequency of the radio signal, MHz 868
Dialog code signal scanning method
System control range *, m 900
Key fob signal reception range*, m 1200
Arming and disarming with different buttons yes
Indication of disarming by another key fob or PIN code yes
Clock, alarm, timer functions yes
Keychain vibration mode instead sound signals and with them
Location control yes
Battery CR2032x2
Guard zones:
doors "-" yes
doors "+"
ignition yes
trunk yes
hood yes
two-level shock sensor yes
additional two-level sensor input yes
Design advantages:
Built-in door lock control relays yes
Two outputs for light signals yes
Number of independent blocking circuits by external relays 2
Type of contacts of external blocking relays H3 and HP
Separate power supply for the circuit of light signals and other circuits yes
The location of the connectors of the central unit is two-sided
System LED indicator integrated into the antenna
Output for control of standard security system yes
Connector for external CAN-bus module yes
Service options:

Number additional channels remote control 3
Function of calling the driver from inside the car yes
Disarming without a key fob - PIN code, bit 1 or 2
Sequential door unlocking function yes
Guarding with the engine running, an additional relay is required
Reassignment of the lock relay control for other circuits yes, additional control. channels
Turbo timer mode yes
Turbo timer operation mode requires additional relay
Second car control yes
Engine start control and control of its operation
Other:
Number of programmable functions 23
Number of operation control modes door locks 7
Anti-carjacking modes from key fob and automatically
Engine blocking during Anti-carjacking intermittent/immediate
Passive engine blocking function yes
Vehicle security while driving
AV trigger function no
Possibility of programming delay of saloon lighting yes 5 or 45 sec.
Reset to factory settings yes
Centurion Xanadu v.3: description, photos, prices, specifications, customer reviews, instructions and accessories.
You can buy Centurion Xanadu v.3 in the Avtozvuk-SPb store in St. Petersburg at a low price.

RECORDING KEY FOB CODES

This procedure is necessary to add new key fobs to the system. Also
it is highly recommended to perform it in case of loss of the key fob, in order to rewrite
codes of existing key fobs and erasing the lost one.

1. Turn the ignition on and off two times, turn it on a third time and

leave it enabled.

2. Within 10 seconds after that, press the service button 3 times, the third time

hold it down until the siren sounds.

3. Press any button on the key fob, a siren will sound confirming

writing the key fob code to the system memory. The number of signals corresponds
the number of the cell in which the key fob code is written. In total, the system can
record up to 4 key fobs.

4. Repeat step 3. for all key fobs that you are going to use. If

You have less than 4 keyfobs, write down one keyfob several times.

5. To exit the recording mode, turn on the ignition, or wait 15 seconds.

The system will respond with 3 siren sounds.

HARDWARE DISABLED PERSONAL CODE

A jumper located on the central unit board allows you to hardware disable
request for a personal code.

By default, the jumper is set on the pin contacts to the position
FREE. When disarming without a key fob and Anti-car-jack mode
code is required.

If the jumper is installed on the pin contacts in the OFF position, then the code
not used (but stored in memory with the possibility of further
use). When disarming without a key fob and Anti-car-
jack, just turn on the ignition and press the service button.

Changes take effect after a power reset!

FOR NOTES

_______________________________________________________________________________

_______________________________________________________________________________

_______________________________________________________________________________

_______________________________________________________________________________

Chapter 1 System Management

KEYFOBS FOR SYSTEM CONTROL

KEY FOB BUTTON FUNCTIONS

KEYFOB MENU

STATE OF THE SYSTEM

ARMING THE KEY FOB

DISARMING THE KEY FOB

DISARMING WITHOUT KEY FOB

SECURITY DURING MOVEMENT

AUTOMATIC ARMING AND PASSIVE LOCKING

CAR SEARCH

DOOR LOCK CONTROL

OPENING THE TRUNK AND OPERATING OTHER DEVICES

SERVICE MODE

ANTI-CAR-JACK (ANTI-CAR-JACK MODE)

TURBOTIMER (for turbocharged engines)

ADDITIONAL FEATURES WITH DISPLAY

TEXT MESSAGES KEY FOB WITH DISPLAY

KEY FOB PICTOGRAMS WITH DISPLAY

Chapter 1 Installing and Connecting the System

COMPLETENESS

ATTENTION INSTALLER!

CONNECTION DIAGRAM AND WIRE ASSIGNMENT OF THE SYSTEM CONNECTORS

Connector #1 - door locks, lights, ground, siren

Connector #2 - sensor inputs and low current outputs

Connector #3 - transceiver module with built-in LED indicators 25
Connector #4 - service button

Connector #5 - shock sensor

Connector #6 - additional sensor(option)

DOOR LOCK CONTROL: CONNECTION OPTIONS

Chapter 3 System Setup and Function Programming

PROGRAMMABLE SYSTEM FUNCTIONS: GENERAL

SETTING THE SYSTEM FUNCTIONS. PART 1

SETTING THE SYSTEM FUNCTIONS. PART 2

Change of personal code

SETTING THE SYSTEM FUNCTIONS. PART 3

SENSOR TEST MODE

RETURN TO FACTORY SETTINGS

RECORDING KEY FOB CODES

HARDWARE DISABLED PERSONAL CODE

Instruction

FUNCTION Centurion Xanadu
The Centurion Xanadu is designed to alert you to unauthorized use vehicle, blocking the engine in start mode, remote execution service functions for all brands of vehicles powered from the on-board network with a grounded negative battery terminal with a nominal voltage of 12V.
Unauthorized installation or use of the Centurion Xanadu for purposes other than its intended purpose will only cover documented manufacturing defects by an authorized repair agent. warranty repair. The responsibility for safety and electromagnetic compatibility in this case rests with the vehicle owner.
The possibility of direct contact with fuels and lubricants must be excluded, detergents, foreign objects with a diameter of less than 1 mm precipitation and dust, damage to the shell. Location near sources of significant radio interference and heat generation is not recommended.
Before and after installation of the Centurion Xanadu in the car, the requirements for the level of radio interference must be met, inside the car according to GOST 28279, and outside the car according to GOST 17822. the number of alarms they trigger is limited (after 10 triggers during one security cycle, the sensor will be disabled).

SPECIFICATIONS Centurion Xanadu
- DESIGN REQUIREMENTS Centurion Xanadu
The mass of the set is not more than 800 g.
The overall dimensions of the central block are 90x74x28mm.
The force on the wires, for a short time, no more than 10 N.
- REQUIREMENTS FOR ELECTRICAL, ACOUSTIC PARAMETERS AND FUNCTIONING
Main specifications Centurion Xanadu
Technical prescriptions according to GOST R 41.97-99 sections 5-7
Inclusion alarm signal and blocking circuits when the product is switched off and its accidental activation is impossible. There is an ignition interlock. Is absent false alarm when the battery is slowly discharging.
General information
- Read the instructions and act in full accordance with their instructions.
- Do not install system elements near the pedals and steering gear.
- Most vehicles are equipped with safety air bags. Be extremely careful not to probe any of the security wires.
- Disable battery before connecting the system.
- Check the inside of the panels you want to drill. Make sure there are no harnesses or other components located behind the panel that are in danger of being damaged.
- Use approved crimp connectors and markers on all wires. Bad wiring, i.e. twisted connections may cause the system to malfunction or fail.
- Place wires carefully under or behind mats to avoid damage.
Route wires away from moving parts, exhaust pipes and wires high voltage. Wrap insulating tape wire harnesses passed through holes. Use insulating bushings. Beware of sharp edges that can damage wires and cause short circuits.
CAUTION: Do not connect harnesses to system components until you have connected ALL wires.

car alarm Centurion Xanadu is a security device with a two-way communication function.

Thanks to the wide range functionality, this device is often installed in cars.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

Arming and disarming modes can be enabled by different buttons, and the buttons are blocked from accidental activation.

The main functional range of the system

The modern two-way alarm system Centurion Xanadu has a large functional range. Among the main security and frequently used additional functions, it is worth noting the following:

• control relay door locks built into the security system;
• Possibility to install 2 LED sensors;
• blocking the engine of the machine using a relay;
• the key fob operates within a radius of 1000 meters;
• there is a function dynamic code management - additional protection from interception;
• using a keychain with a liquid crystal display, you can fully
• control all functions of the security system;
• you can block the buttons from accidental activation;
• the functions of the vibration signal, timer and alarm clock are active;
• there is a sound accompaniment of pressing buttons;
• the system notifies about the state of the battery and its discharge;
• you can set the economy mode to save battery power for a longer period;
• the functioning of four additional channels, to control additional features and vehicle systems
• doors are unlocked by using a two-step mechanism;
• locking doors using the brake pedal.

Also, the system uses a 2-level shock sensor, has 5 security zones, which are independent, allows you to use passive mode to block the engine and covert protection mode. There are 2 anti-theft protection modes and a panic mode.

Security system package

The complete set of the security system of the specified model is as follows:

1. Central control unit.
2. Keychains and 1 keychain with LCD indicator.
3. The shock sensor is two-level.
4. Transmission and reception module.
5. Relay designed to block the engine.
6. Emergency button Valet.
7. Red LED indicator.
8. Glass stickers and 6 wires for installing a security system.
9. User instruction.

The security system operates at a voltage of 12 V, operates at -40 frost and +85 heat. The weight of the device is less than a kilogram, or rather 750 gr. Produced anti-theft system in the country of Taiwan.

Automotive alarm CENTURION XANADU instruction

User guide

SYSTEM MANAGEMENT:

A. BUTTON FUNCTIONS OF BOTH KEYFOBS:

ADDITIONAL KEY FOB BUTTONS WITH DISPLAY

B. KEY FOB LOCK:

Key fob lock is used if you are afraid of the consequences of accidentally pressing the buttons. To disable buttons:

C. STATUS INDICATOR OPERATION

D. SOUND SIGNALS

E. LIGHT SIGNALS

F. SYSTEM STATUS

* Armed mode off

G. ARMING

ARMED will appear on the keyfob display and LCD.

ACTIVE SENSOR REMINDER:

If three beeps sound, the doors, hood or trunk are not closed. (See section "Programmable functions" table #1, function #4)

The icon of the active sensor will appear on the display of the remote control with feedback and the LCD.

SILENT ARMING/DISARMING: Press the buttons and remote control at the same time, the security mode will be turned on or off. There will be no sound signals, arming/disarming will be confirmed only by light signals.

DISABLE THE SHOCK SENSOR: Press the key fob button twice within 3 seconds, the system will arm and disarm the shock sensor. The system will inform you about the sensor disconnection with an additional sound signal. Disabling the shock sensor is valid only for one protection cycle. The system will return to normal operation the next time the system is armed.

SILENT ARMED MODE: Press the button, then the key fob button. After a sound signal confirming the arming mode, two more will follow - one short and one long. The duration of the alarm when the shock sensor is triggered will be reduced from 30 to 12 seconds. The low-noise arming mode is valid for only one arming cycle. The system will return to normal operation the next time the system is armed, if it is armed normally.

PASSIVE LOCK:

The purpose of this function is to permanently protect the car from theft, regardless of the arming mode. The lock will be activated 60 seconds after the ignition is turned off. The status LED, with the passive lock function programmed, flashes rapidly for 60 seconds after the ignition is turned off. After 60 seconds, after switching on the passive blocking led indicator status blinks slowly (half the frequency of normal arming). The system in the passive blocking mode activates the alarm only when the ignition is turned on.

HIDDEN GUARD MODE: Press the button and then the key fob button. The system will turn on the armed mode, in which the siren does not turn on. The alarm signal is transmitted to the key fob and is accompanied only by flashing light signals.

H. AUTO-ARMING

In addition to arming and disarming with the key fob, the system has an automatic arming function, which turns on the armed mode 30 seconds after the ignition is turned off and the doors are closed and operates as follows:

1. Turn off the ignition and get out of the car.
2. After the doors are closed, the status LED will flash rapidly for 30 seconds. If a door, hood or trunk is opened during this time, the LED indicator will turn off, the countdown will stop and will start again only after closing the door, hood or trunk.
3. At the end of the countdown, the system will automatically turn on the security mode. One sound signal and one light signal will confirm the activation of the mode.

AUTOMATIC ARMING WITH DOOR LOCKING(See section "Programmable functions" table #1, function #2)

The car doors will be automatically locked when the auto-arming mode is activated, if the corresponding function is programmed.

CANCELING AUTOMATIC ARMING AND AUTO RETURN TO ARMED MODE: When disarmed, when the status LED flashes quickly, press the button twice, the system will answer with one beep, the LED will be constantly on. The system will remain in this state for an arbitrarily long time. To re-enable the auto return function and automatically turn on the mode, press the button or key fob.

I. DISARMING

ALARM REPORT: If the system triggered an alarm, when disarming, there will be 4 sound and 3 light confirmation signals.

Corresponding icons will appear on the display of the remote control with feedback and the LCD.

LIGHTING THE PATH(See "Programmable functions" table #2, function #4): This function turns on the light signals for 30 seconds after disarming or remote door unlocking and for 10 seconds after arming or remote door locking.

TWO STEP DOORS UNLOCKING: This function automatically unlocks only the driver's door when the system is disarmed. To unlock the passenger doors, it is necessary to press the key fob button again within 3 seconds after disarming.

AUTOMATIC RETURN TO ARMED MODE(See "Programmable Functions" Table #1, Function #3): This function will automatically arm the system 60 seconds after disarming. Automatic return to armed mode is canceled if doors, hood or trunk are opened within 60 seconds after disarming.

J. DISARM WITHOUT KEY FOB

(See section "Programmable functions" table #5, function #2)

EMERGENCY DISABLED WITHOUT PERSONAL CODE (FACTORY DEFAULT)

Emergency disarming is used in case of loss or malfunction of the key fob.

1. Within 10 seconds, press the service button. The siren will stop sounding, the security mode will turn off.

EMERGENCY DISABLED BY PERSONAL CODE

If a service switch is available this system allows you to program private idintifier. This suggests more high level protection.

1. Open the door, the alarm will sound. Turn on the ignition.
2. Within 15 seconds, press the service button a number of times equal to the first digit of the personal code. The start of entering the first digit of the personal code must be no more than 5 seconds from the moment the ignition is turned on.
3. Switch the ignition off and on again.
4. Enter the second digit of the personal code.
5. Switch off the ignition. The security mode will turn off.

Four sound and 3 light signals will confirm disarming.

Remark 1. You must complete the procedure emergency shutdown armed mode within 60 seconds from the moment the service button was first pressed, otherwise the system will automatically return to the armed mode.

Remark 2. If the code is entered incorrectly, the user is given two more attempts, and if the first digit of the code is entered incorrectly, this is already considered an attempt, then the code entry is blocked for 5 minutes. During these 5 minutes, the LED will flash at a frequency of about 1 Hz and with very short pauses - about 0.1 seconds.

K. SERVICE MODE

The security mode is disabled or the system is in service mode)

The service switch allows you to temporarily turn off all security functions system, which eliminates the need to transfer the key fob service personnel. Before turning on the service mode, the security mode must be turned off - with a key fob or using an emergency shutdown.

In the service mode, the security functions of the system are disabled, but the "Panic" mode is activated and the door locks are remotely locked and unlocked.

When controlling the remote locking and unlocking of door locks in the service mode, the key fob display with LCD and feedback displays the corresponding icons:

Turning on service mode

1. With the security mode turned off, turn on the ignition.
2. Press and hold the service button until the LED indicator lights up. The status LED will be on continuously while service mode is enabled.

Turn off service mode

1. Turn on the ignition.
2. Press and hold the service button until the LED turns off.

Enabling and disabling the service mode with a key fob

To turn the service mode on or off, press the key fob button three times within 3 seconds. One light signal will confirm the inclusion of the service mode, two - off.

L. MACHINE SEARCH

To search for a car, press the key fob button with LCD or the key fob button without feedback. The signal lights will flash 12 times.

M. PANIC

(See section "Programmable functions" table #5, function #4)

Keychain can be used for remote start anxiety in a dangerous situation.

The icon will appear on the display of the key fob with feedback and the LCD.

N. ALARM

In armed mode, a light blow triggers the first level of the shock sensor and three short sound warning signals.

A strong impact, opening doors, hood or trunk, turning on the ignition causes an alarm. The siren, side lights and interior lights come on for 30 seconds to alert you to an intruder. The interlock circuit protects the vehicle from unauthorized starting of the engine. At the end of the alarm cycle, the system will remain armed. If one of the sensors is continuously active, the system will turn on the alarm for 6 cycles of 30 seconds.

TO ERASE THE ALARM CAUSE MESSAGE FROM THE DISPLAY AND MUTE THE BEEP OF THE KEY FOB: After the alarm is triggered, the key fob sounds and the key fob display with feedback and LCD displays the cause of the alarm.

To interrupt the audible signal and clear the reminder of the causes of the alarm from the display, press the button three times within three seconds. SET keychain.

Press any keyfob button to interrupt the beep of the keyfob.

ALARM LIMIT: The system has a noise reduction circuit. It prevents multiple triggering in case of faulty sensors or in conditions of increased noise and vibration.

When continuously active sensors doors, hood or trunk, or the ignition is on, the number of alarms is limited to five, after which the system turns on the bypass of the sensors.

Repeated activation of door sensors causes an alarm, all other security zones are turned off until next inclusion protection mode. Maximum amount triggering of the second level of the shock sensor in one security cycle is equal to five.

O. ANTI-CAR-JACKING MODE

A warning: If you do not need the anti-robbery feature, make sure it is turned off. By default (factory setting), the anti-robbery function is disabled. (See "Programmable functions" section, table #3, function #1)

PROTECTION ANTI-THRUG MODE ACTIVATED WITH KEY FOB

ANTI-THRUG MODE AUTOMATICALLY ENABLED

1. The mode turns on automatically when the ignition is turned on.
2. After opening and closing the door with the ignition on, the mode is activated.

OPERATION OF THE SYSTEM IN THE ANTI-THREAK MODE

The robbery protection mode after its activation consists of three periods.

First stage:

1. 50 seconds after activation of the mode, the siren emits short warning signals for 15 seconds.
2. During these 15 seconds, you can turn off the mode by pressing the service button.
3. If this is not done, the system will turn on the second stage.

Second phase: 65 seconds after the mode is activated, the system will trigger an alarm. The siren sounds continuously, side lights and interior lighting flash.

Third stage: 90 seconds after the activation of the mode, the system turns on the alarm and blocking. The parking lights are flashing, the siren sounds continuously, the engine is blocked. The third stage is not limited in time.

TURNING OFF THE ANTI-THRUG MODE:

Turn off the ignition, then turn it on again and press the service button no later than 10 seconds later. The alarm will turn off, the engine will be unlocked.

Note: If a personal code is programmed to increase the security level of the system, the alarm is turned off by entering a personal code.

P. ALARM REPORT REQUEST

You can query the system about the alarms that have occurred. To do this, click the button SET, then no later than 3 seconds, the key fob button.

On the display of the key fob with feedback and the LCD, icons will appear corresponding to the sensors that have caused the alarm since the last ignition was turned on.

Q. SYSTEM HEALTH MONITORING

Double click the button SET, then, no later than 3 seconds later, the key fob button.

An audible signal will follow, and the keyfob LCD display will show the system status.

R. DRIVER CALL

This feature is used when someone wants to call the driver. The call can be made both by a passenger inside the car, and by any passer-by outside the car.

CALLING THE DRIVER FROM THE CAR

With the ignition off, press and hold the service button for more than 2 seconds until you hear short signal sirens.

The driver call indicator will appear on the LCD keyfob display and the keyfob's beep will follow.

CALLING THE DRIVER FROM OUTSIDE THE VEHICLE

If the driver's call sensor is installed on the car (it is usually mounted on inside windshield in the lower right corner), then the driver can be called by light blows in the sensor area. At the same time, a short siren signal will sound, a flashing icon will appear on the LCD keyfob display, and the keyfob will sound.

The function to call the driver outside the car must be previously activated and works until the arming or disarming mode is turned on or off.

To activate the driver call sensor, press the button SET

To disable the activated glass shock sensor, press the button SET, then, no later than 3 seconds, the button.

S. INTERIOR LIGHT CONTROL

The interior lighting function works as follows:

1. After disarming, the interior lighting stays on for 30 seconds.
2. In the event of an alarm, the interior lighting flashes as long as the siren is sounding.

Note: Cabin lighting will go out earlier than 30 seconds if you turn on the ignition or the armed mode.

T. AUTOMATIC DOOR LOCK CONTROL WHEN IGNITION ON AND OFF

See "Programmable functions" section, table #2, function #2)

If the door locks are controlled by the system, the doors will automatically lock a few seconds after the ignition is turned on, and unlock immediately after the ignition is turned off.

U. TRUNK UNLOCKING (CHANNEL 3)

Press and hold the key fob button for more than 2 seconds to remotely unlock the trunk or activate other devices connected to the output of the third channel.

The corresponding icon will appear on the display of the key fob with feedback and the LCD - "open trunk"

V. CONTROL OF AUXILIARY DEVICES CONNECTED TO THE FOURTH CHANNEL OUTPUT

(See "Programmable functions" section, table #4, function #2)

Press buttons and simultaneously to activate the 4th channel. Channel 4 is programmable in duration from 1 to 120 seconds. You can use it to control power windows, sunroof, low beam. (In the factory-set state, the channel output signal appears and disappears synchronously with pressing and releasing the keyfob buttons)

W. CONTROL OF AUXILIARY DEVICES CONNECTED TO THE FIFTH CHANNEL OUTPUT

(See "Programmable functions" section, table #4, function #3)

Press buttons and simultaneously to activate the 5th channel. Channel 5 is programmable in duration from 1 to 120 seconds. You can use it to control power windows, sunroof, low beam. (In the factory-set state, the channel output signal appears and disappears synchronously with pressing and releasing the keyfob buttons)

X. CONTROL OF AUXILIARY DEVICES CONNECTED TO THE SIXTH CHANNEL OUTPUT

(See "Programmable functions" section, table #4, function #4)

Press buttons and at the same time to activate the 6th channel. Channel 6 is programmable in duration from 1 to 120 seconds. You can use it to control power windows, sunroof, low beam. (In the factory-set state, the channel output signal appears and disappears synchronously with pressing and releasing the keyfob buttons)

Y. STATUS MEMORY

The system retains its state when the power is turned off and then turned back on. When the power is turned off in armed mode, the system will trigger the alarm after the power is turned on.

KEY FOB WITH DISPLAY

A. KEY FOB DISPLAY ICONS

B. PROGRAMMING THE DISPLAY KEYFOB

KEY FOB DISPLAY BACKLIGHT: Press and hold the button SET about 1 second, a beep will sound and the display will light up for 5 seconds.

ECONO MODE KEY FOB: In economy mode, the key fob consumes a minimum current.

Inclusion:

Press and hold the button SET within 5 seconds, until the sound signal and the inscription "SAVE" on the key fob display confirm the inclusion of the economy mode.

Shutdown:

Press any button on the key fob to turn off the economy mode.

ERASING REMINDER SIGNALS FROM THE KEY FOB DISPLAY: Click the button SET three times within 3 seconds, the display will be cleared of reminder signals in the form of various flashing images, the sound signals will turn off.

KEY FOB BEEP INTERRUPTION: After the system is triggered, the key fob sound signal and the image on the display inform the owner of the alarm. To interrupt the sound signal (only the sound signal!) of the key fob, it is enough to press any button.

DISABLE KEY FOB BUTTONS: This function is used to temporarily disable the key fob buttons in order to avoid the consequences of inadvertently pressing the buttons by strangers. Click the button SET, then within 3 seconds, press and hold the button for more than 2 seconds, until the key icon appears in the lower right corner of the key fob display.

TURN ON/OFF THE KEYFOB VIBRATION FUNCTION: This feature is used to replace the key fob beeps with a vibration function in very noisy places where it is difficult to hear the beep.

Click the button SET key fob, then within 3 seconds, press and hold the button for more than 2 seconds until three wavy lines appear or disappear at the bottom, in the center of the key fob display, indicating that the vibration function is turned on.

Enabling/disabling the beeps of the remote control that confirm the pressing of the buttons: If you want the keyfob buttons to be pressed without confirmation beeps, press the SET button, then within 3 seconds, press and hold the button for more than 2 seconds.

INDICATOR OF THE DISCHARGE OF THE POWER BATTERY OF THE KEY FOB: When the battery life of the key fob runs out, each time you press any button, a double confirmation signal sounds, and only one dark sector remains on the battery discharge indicator in the lower left corner of the display.

PROGRAMMING THE COUNTDOWN TIMER:

Notes:

1. The timer has fixed intervals of 10, 20 and 30 minutes, 1, 1.5 and 2 hours.
2. When the time is set to 0:00, it means the timer is off.
3. At the end of the timer, press the button SET to return to the current time display.

SURFACE INDICATOR:

1. When you are in the zone of reliable reception of signals on the key fob display, in the upper right corner, an image of a television tower appears.
2. In case of violation of the two-way exchange between the key fob and central block the indicator of good reception disappears from the key fob display.

Attention! The information on the keyfob display screen is updated every 20 minutes if the appropriate software setting is selected or when the "System Status Request" function is performed.

To replace the element, slide the cover lock to back wall keychain. When the element is replaced, a melody will sound, all the icons will appear on the display for a few seconds, the key fob will vibrate, the time indicator will be set to: AM 12:00. Set the time after replacing the battery.

B. REPLACING THE BATTERIES IN THE KEY FOB WITHOUT FEEDBACK

The open-loop key fob uses 2 3V CR2025 batteries. With regular use of the key fob, the battery life can reach 1 year, and with periodic use up to 2.5 years. To replace the batteries, unscrew the screw on the bottom side of the key fob and, observing the polarity, replace the batteries.