Finishing the bathroom with self-adhesive film. Self-adhesive film for the bathroom: photos, types, use. The method of gluing decor on a wet plane

With the help of self-adhesive film, the bathroom can be transformed beyond recognition.

The only trouble is actually with its gluing, very often after pasting it just falls off. There are two possible reasons for this problem:

1 reason

In the film itself, or rather in the adhesive composition with which it is processed, it may simply be old or of poor quality. How to check the expiration date, especially if the goods are ordered from China, I myself did not understand, but in the store the seller must show you the documents for the goods, and on the label, if it has not been re-glued, there should be a release date.

2 reason

Walls, or rather their surface. Self-adhesive film adheres pretty well to any objects, if they are clean. Therefore, before proceeding with gluing, first clean the wall of debris with a stiff brush, if necessary, you can also use a brush with a metal bristle.

After washing with the product, rinse well with water and dry the wall so that there is not even a hint of moisture.

Now let's move on to washing the wall with a solvent, it is better to apply it through a dispenser and wipe it with a cotton rag without lint and threads. Dry the wall after the solvent.

It is best to glue from below, it’s easier for me, but you can from any side. Tear off the edge of the protective layer and, while gluing, slowly pull off the protective layer, and the assistant should smooth the film from the place of the already glued film to the side of gluing with a rubber roller so that bubbles do not form. Then, in order to remove them, you will have to spoil the film itself with a needle, no matter how sharp the needle is, but traces remain.

The statement that bathroom renovation is a very expensive pleasure is no longer relevant. It can be beautiful, original, practical and not expensive at the same time. If only self-adhesive bathroom film is used for wall decoration.

When repairs need to be done quickly and at the same time meet the minimum budget great solution becomes a decorative self-adhesive film.

An example of the use of film in bathroom design

This is enough new material, which has not yet gained wide distribution and is often associated with unattractive washable wallpaper from the recent past, which is fundamentally wrong. A variety of colors and textures allow you to achieve very interesting design, and with proper execution, such a finish will last up to 10 years.

Self-adhesive film for bathrooms, how to choose

Self-adhesive wallpaper for the bathroom is a finishing material, on reverse side which is inflicted adhesive base and protected by special paper. The film goes on sale in the form of rolls with a width of 45 to 95 cm and a length of up to 15 meters.

Any pattern can be applied to the film

Self-adhesive wallpapers come in four types:

• Cork: In their structure, they resemble natural cork finish. The surface of the material is additionally coated with a wax-based composition. PVC film. Comprises artificial materials. Diverse in color, pattern and texture. Differs in the increased term of operation.
• Satin: Such wallpaper for finishing the bathroom is also called fabric.
• Self-adhesive film: Convenient in that they have their own adhesive coating. most convenient and suitable option for finishing bathrooms. Color variations can be very diverse, from plain to complex patterns and ornaments. It is also possible to simulate natural materials such as wood or natural stone.

Types of wallpaper for the bathroom

The surface of the film can be:

• matte;
• glossy;
• rough;
• metallized.

The metallized surface allows you to create certain visual effects: mirror, fluorescent, stained glass (transparent or shaded) and drawings with a 3d effect. Before choosing a film, you need to pay attention to the manufacturer. Manufacturing companies long years tend to provide better quality products.

Decorative film in interior design

It is not difficult to paste over the walls in the bathroom with a film, but will the effect of such a decision please, especially considering the fact that as an element of decor, the film has no equal.

Decorating bathroom walls with foil

Self-adhesive film allows you to effectively decorate the pipes in the bathroom. This solution will look very impressive if you choose the right material. In a rustic interior, pipes are usually wrapped with a beautiful structural rope, but they can also be hidden under a film imitating wood.
For interior in Japanese or chinese style pipes are made like columns, pasted over with a red film and decorated with black hieroglyphs.
Combinations of films of different shades and textures and changing their geometry allows you to effectively zone the space. Often, the film is combined with other finishing materials, for example, with tiles or using liquid wallpaper for the bathroom. To highlight areas more prone to moisture.

Advantages and disadvantages of the material

Like any other finishing material, self-adhesive film there are pros and cons that you need to consider before deciding in favor of a simple budget repair.

Advantages

• The material is presented in a wide range of colors and textures.
• The cost of the film is an order of magnitude lower than others finishing materials.

Using a film for pasting the walls of the bathroom is a fairly budget option

• Not bad quality characteristics which make this bathroom wallpaper enough practical option.
• Pasting works take a minimum of time and effort, do not require special equipment and are easily done independently.
• The glued surface does not require additional care.
• Possibility of finishing various types of surfaces.

Flaws

• Despite the simplicity of pasting, surface preparation is a rather laborious process and is not always possible for a person without special experience.

Special skills are required to work with film

• The film is highly waterproof, but this is not only a plus, but also a minus of the material. Since the wall under such a coating does not breathe, which means that diaper rash and mold may form.
• The term of operation, as a rule, does not exceed 10 years. But this can be a plus for those who like to change the interior often. Easy Installation and low cost allows redecorating more often than usual.

Preparatory work.

Decorative film sticks to almost any surface. It doesn't matter if it's cork, glass, plywood, tile, wood or metal. You can stick it on putty or unprepared drywall, but the material will not last long on such a surface.

Leveling the wall surface before pasting with a decorative film

The success of the repair depends primarily on proper preparation walls. The old coating is completely removed from them, leveled, puttied in two layers, cleaned with a fine abrasive sandpaper and primed.

When the surface is completely dry, a horizontal line is beaten off on the wall, along which the first canvas will be glued. Usually they try to make this mark in the most inconspicuous place, since the first and last strips will dock differently than the others.
If liquid wallpaper or decorative plaster for the bathroom, the preparation of the walls in these areas does not have to be done so carefully. The mixtures themselves hide small surface defects well. Walls should be primed enough.

Material calculation

In order to count required amount film, you need to know in advance the width and footage of the roll. Room measurements are performed without taking into account windows, if any, doors and space behind the bathroom. First, they find out how many strips of material are needed to glue all the walls. To do this, the perimeter of the room is divided by the width of the roll. After that, they calculate how many strips can be obtained from one roll. To do this, its footage is divided by the height of the walls with an increase of 5-10 cm for trimming.

Before buying a film, carefully calculate the required footage

When wallpaper for a bathroom with patterns or a geometric pattern is used, in addition to the stock, an adjustment is added to the height - 35-45 cm. The total number of strips that will be required to paste over the entire room is divided by the number of strips in one roll and the number of rolls necessary for repair is obtained. If the bathroom has ledges or niches to total number add another roll. Methods for pasting the surface with a decorative film.
The temperature in the repaired room should be at least 10 degrees. If the film has been previously stored at more than low temperatures it is desirable to keep it warm for at least two days. After graduation preparatory work start cutting the film and gluing it.

Material cutting features

As a rule, the film is cut from the wrong side, on which square markings are applied for convenience. But in some cases, when, for example, the selected film is designed to imitate tiles, the markup is performed taking into account the front drawing. Additional instructions for working with a particular type of material are always indicated on its reverse side.

It is more convenient to cut the material according to a special markup

The cutting of the panel is carried out along the length with a special construction knife. Cutting the film on weight or with scissors is not recommended.

Surface pasting

Glue the film from top to bottom. A protective layer is removed from the upper edge of the first strip for a few centimeters. The film is applied to the wall and leveled. Gradually remove the paper protection by 5-6 cm, pressing the adhesive surface against the wall. When the entire strip is pasted, it is smoothed rubber spatula from top to bottom and from the center to the edges, trying to get rid of all the wrinkles and air bubbles at once.

Important! Any wallpaper for bathroom walls is glued back to back, but the film is always glued with an overlap.

It is better if the edges of the overlapping panel are facing the light source in the room. Otherwise, the seams will cast a shadow and become more visible. Joints of strips in the corners are recommended to be avoided.

If you are gluing a decorative film for the first time, you will need an assistant

Important! The decorative film fully sets after a few hours. In the near future after gluing, the material can be torn off with a sharp movement and pasted again.

If some air bubbles nevertheless formed, they must be carefully pierced with a thin needle and smoothed out. It is almost impossible to remove wrinkles and irregularities from an already glued surface, the strip is torn off and glued again. If the film is pasted on a convex surface, it is preheated with a building hair dryer in order to make it more elastic.

To be more precise, we are talking about cosmetic repairs of walls, and with minimal cost. Self-adhesive film will be an excellent budget choice that will allow you to long time renew the coating, which can be easily maintained if necessary.

The sticker of a film can be carried out on absolutely any surface.

For example, on:

• metal;
• Wooden;
• Cork;
• Tiled.

It is worth noting that even for metal it is not necessary to use special compounds to improve the adhesion of the canvas and the base, since the film has a powerful adhesive coating.

Why is film perfect for the bathroom?

It has such a remarkable quality as moisture resistance, as well as the ability to withstand temperatures up to 80 ᵒС.

Goes on sale great amount varieties of this material, and it is possible to choose a canvas of the most creative type.

Among positive sides, you can note:

• Optimal cost;
• Availability;
• A large assortment;
• Ease of installation;
• Ease of care;
• Long service life.

Special rubberized films began to appear on the shelves of stores with building and finishing materials, which are not only water-repellent, but also moisture-absorbing.

The film adheres well to any surface, including plaster. If the plaster crumbles and crumbles, it is better to pre-work on hardening, grouting and priming. Only after that you can be sure that the applied film will not fall off along with the plaster layer.

Like any finishing material, the film has its drawbacks that cannot be ignored:

1. The material is absolutely non-breathable, which means that oxygen access to the walls is completely blocked.
2. There is a high chance of mold and mildew development.

It is quite possible to avoid these problems if you install excellent ventilation in the room, and also, before sticking, it is worth treating the walls special composition which prevents such problems from occurring.

Correct self-adhesive film sticker

For any finishing works advance preparation is required. Namely, it is imperative to clean the walls of hooks and similar protrusions or products so that there are no obstacles during application.

The peculiarity of the installation is that the coating on which the film will be glued must be:

• Dry;
• Pure;
• Smooth.

First, defects on the walls are eliminated, in particular, puttying and priming are carried out.

To do this, you should use compositions made on the basis of acrylic.

If a metal surface is to be pasted over and there is rust on it, it must be completely removed and the coating soaked with a liquid to prevent re-formation. Canvases made of wood and glass are simply wiped with alcohol to remove the fatty film.

Be sure to have a set of necessary tools at hand.

Namely:

• Pencil;
• Roulettes;
• metal ruler;
• scissors;
• sharp knife;
• Special spatula;
• Industrial hair dryer.

To increase the adhesion of the pasted web of the applied new coating, it is possible to slightly moisten the product before direct installation if it is metal or glass. If everything that is required is at hand, and at the same time a sufficient amount of film, then carry out work on pasting the bath standard size possible in one day. You do not need special training, help, well, perhaps, to push back household appliances and no more. The film after installation does not require a long time to dry, which means that immediately after the repair you can take a shower and use the bath in the usual way.

Types of film for the bathroom

On sale you can find self-adhesive film only in rolls.

Rolls may vary in size.

• Length - 8-10 m;
• Width - 45-50 cm.

As for the method of sale, it all depends on the outlet, as some sell the canvas exclusively in rolls, while others sell in meters.

There are samples, the length of which reaches 15 m. Their peculiarity is that the cost is low, and one unit of goods is enough to finish the whole bath.

Color spectrum self-adhesive film just knows no bounds.

There is an incredible amount of such materials, each of which differs in:

• color;
• Hue;
• drawing;
• Decor and so on.

Particularly popular are those film models that can become the most real imitation tiles or wood. There is an imitation of metal, mirrors and even doors. Such options for finishing the bathroom, given the fact that the room has minimal dimensions, help to visually expand the space, which will make the bath more comfortable and cozy to stay. The imagination of designers is almost limitless, and every day new types of this material are released.

How to stick a self-adhesive film

Naturally, when redecorating a bathroom or toilet, it is worth finishing it completely, and not partially. Otherwise, it may look like bad taste and nothing more. Due to the fact that the bath with a toilet does not take up much space in terms of quadrature, you will not have to spend too much money.

The choice of 2 types of film will look more original. For example, a plain background and bright inserts.

This decor will be great. creative solution, and also so you can hide various defects on the walls.

For example:

• Irregularities;
• chipped;
• potholes;
• Places where hooks were previously glued or where pipes were installed.

For toilets, stained glass films are most often used, as they help to visually expand the space. If there is one light source in the bath and this is an ordinary lamp, then you can choose a film with mirror surface or install additional Spotlights. This solution will look very stylish and unusual.

Most importantly, in narrow and small rooms, do not pile up the walls with bright and large drawings and also do not use dark tones.

Often the film is used in conjunction with tiles. To be more precise, it is used for restoration wooden door or plastic wall panels if such are installed indoors. The main thing is not to overdo it, since there must always be a measure and taste so that the interior design does not turn into a mess.

The use of self-adhesive film for the bathroom (video)

Self-adhesive film may be suitable for finishing the bath, but only on the condition that it is correctly matched to general interior. In this case, you can not worry about the violation of harmony and comfort.

Many people believe that bathroom renovation is a very expensive pleasure. But it can be economical, original and practical if you use a self-adhesive film to decorate walls, doors or furniture. It is an excellent material endowed with numerous advantages. It allows you to create unique coating furniture and walls, which cannot be achieved using other, even more expensive materials for cladding.

Main characteristics of self-adhesive film

In bathrooms, a self-adhesive film is used, created on a siliconized basis and treated with glue on one side and covered with PVC film on the other. Often this material is sold in rolls, the width of which can be 45-95 cm, and the length - 2-15 m.

Self-adhesives of different textures and colors allow you to divide the space of the room into separate zones. For this, a material of a similar color, but a different texture, is selected. For example, the zone is made “under the tile”, and the baths - “under the tree”.

The film adheres perfectly to glass, wood, plywood, plaster, metal, etc. With its help, you can finish beams or pipes “under columns”, create “platbands” around cabinets and doors, update shelves or even a door. Besides, given material combined with liquid wallpaper or tiles, can become an element of decor.

Self-adhesive film sticks well to almost any surface

There is a wide variety of sticker colors on the market today. It can be monophonic or with complex ornaments and patterns, it can imitate stone or wood.

There are such main types of surfaces of self-adhesive film:

• glossy,
• Matte
• textured,
• cramped,
• Metallized.

By using metallized film you can create various visual effects: stained glass, fluorescent, mirror, 3d-drawing, etc.

Pros and cons of self-adhesive film

Before choosing this budget one, you should consider all its advantages and disadvantages. According to customer reviews, the main advantages of self-adhesive are:

1. Low price, which is much lower than most other finishing materials for bathrooms.
2. A rich selection of colors and textures.
3. Enough high quality, thanks to which the film is considered a practical option for finishing bathrooms.
4. Easy to apply on different surfaces requires a minimum of tools and time.
5. Doesn't need special care after gluing.

Self-adhesive film is rich in various patterns, colors and textures

Among the shortcomings of this finishing material, the following should be highlighted:

• Before gluing, you need quality training surfaces. This process is quite laborious and not every person can handle it.
• The waterproofness of the film leads to the fact that after it is applied to the bathroom walls, mold and diaper rash may appear.
• Limited period of application (about 3 years), which, according to consumer reviews, is considered too short.

Preparation of surfaces for finishing

To cover certain surfaces with self-adhesive, it is necessary to prepare the following tools in advance:

• assembly knife,
• ruler and marker,
• Sandpaper,
• Detergent,
• office scissors,
• building hair dryer,
• Felt spatula.

So that numerous surface irregularities do not appear after pasting, before facing works it needs to be processed:

• Thoroughly clean the surface so that it becomes perfectly even and smooth. Repair any cracks found with putty. All roughness is diligently polished with sandpaper.

Attention! metal surface it is necessary to especially carefully cover with a primer, wood - sand and polish, drywall - putty and clean.

• Surface treatment acrylic primer. This will achieve maximum reliability of gluing the material.
• Delete greasy spots with water and detergent.
• Before sticking the film on metal or glass, these surfaces need to be slightly moistened.

Self-adhesive film can be finished as part of the room, and as a whole

Stages of finishing bathroom walls with self-adhesive film

After the walls of the bathroom are carefully prepared, you can start pasting them:

• Using a ruler and a marker, mark the self-adhesive on the back side.
• Cut the film into pieces. To do this, put it on a hard surface, place the ruler along the drawn line and draw with a knife.

Attention! The film with the ornament should be cut with front side, adhering to the edging of the depicted figures. If the self-adhesive imitates tiles, then it should be cut along the lines that represent the seams.

• Separate the self-adhesive from the substrate by 2-3 cm and attach this edge as accurately as possible to the wall in the required place. Then, with one hand, gently and slowly pull the substrate, and with the other - smooth the film. Smoothing should be done with a felt spatula according to the principle “from the middle of the canvas to the edges”.
• If bubbles are detected, carefully pierce them with a thick needle, and then carefully smooth them out with a spatula.
• If folds and wrinkles appear on the surface of the film, tear off the edge of the material from the wall, then re-glue and smooth. The slightest defect must be corrected immediately, since after a few hours it will be impossible to tear off the self-adhesive without damage.
• To finish the corners, cut off a part of the film in the right place (observe an angle of 45 degrees), then bend the edge and glue it.
• Using building hair dryer, qualitatively paste over bulges, joints and round edges. Heat the self-adhesive with this device, after which it will become elastic and perfectly cover uneven surfaces. The video below will also help to cope with pasting the walls of the bathroom.

Following a similar principle, not only walls, but also other surfaces are pasted over. After gluing, the film does not require special care. Contaminants are usually washed away with liquid detergents. Stubborn stains are removed with ethyl alcohol.

Attention! Do not clean the facing film with powder detergents and solvents based on petrol or acetone. They can completely or partially damage the finish.

In general, self-adhesive film is considered good option fast and inexpensive finishes bathroom. This is evidenced by customer reviews who have already used this material to renovate the premises. Self-adhesive, correctly matched to overall design rooms, will make the bathroom even more practical and original.

Video: Self-adhesive film in the bathroom

At first glance, it seems that renovating a bathroom is a fairly simple task. In fact, even this small room needs special attention, because it is exposed to moisture and elevated temperatures. So that, despite such features, the room remains attractive in appearance, it is necessary to responsibly approach the choice of finishing materials. For this purpose, tiles are often used, which can be updated with a conventional self-adhesive film.

Features of self-adhesive

Front side of self-adhesive film made of PVC and covered with protective polymer layer, thanks to which operational properties products are improving. Moreover, the self-adhesive material is shiny. His backside- This is a sticky base covered with paper.

The main advantage of the product is the possibility of gluing any type of surfaces in the bathroom. It can be tiles, metal, plywood or drywall sheets, cork, wood, glass, and even plaster.

Before starting work, prepare the surface, which in the end should be smooth and even, because the self-adhesive film is quite thin, which means that any defect will be visible. In particular this applies light walls bathroom. If you use a colorful self-adhesive tape, some irregularities will be invisible.

To other benefits self-adhesive material applies to:

• water resistance;
• a rich selection of colors, patterns and textures, which allows you to decorate the interior in various styles;
• resistance to high temperatures;
• ease of installation;
• ease of care;
• affordable price.

Naturally, with self-adhesive film there are a number of disadvantages:

• water resistance, due to which the film cannot "breathe";
• need pre-training that includes the elimination various defects surfaces;
• fragility, which is offset by affordable price and ease of installation.

Varieties of self-adhesive film

On sale meet these types of material:

All these varieties are produced in rolls. Their width fluctuates within 45–90 cm, and the length is 2–15 m. The price of the material depends on a number of factors, including size, pattern, texture and manufacturer.

Covering the surface with film

To glue the walls in the bathroom or kitchen, you will need the following tools:

• scissors;
• building hair dryer;
• pencil and ruler;
• special soft spatula.

Before starting work prepare the surface. To do this, it is cleaned of the old coating and degreased. The next step is alignment. If the wall is cracked or rough to the touch, it is covered with a layer of putty and sanded. After that, a primer is applied to the surface. Best to choose acrylic material which improves adhesion.

Self-adhesive film also needs special training. First you need to determine the dimensions of the wall and mark it with a pencil. Then the self-adhesive is cut, taking into account the markings provided on the paper backing. For cutting the film, a mounting knife or ordinary scissors is suitable. All pieces should have a margin of 2-2.5 cm. If available geometric pattern marking is always done from the front side.

Wall pasting carried out in several stages. First, the substrate is separated from the upper part of the material, applied to the surface, glued and smoothed with a rubber spatula. Then the substrate is carefully removed, continuing to smooth the film.

Adhesive tape considered a unique modern material designed to decorate the kitchen and bathroom. Self-adhesive is easy to install, retains its color and shape, and is also sold at affordable price. This self-adhesive material does not need special care. It is enough to periodically wipe the surface with a damp cloth, and ethyl alcohol will help to remove severe contamination.

Self-adhesive film for bath walls