Tire swing
do it yourself

Do-it-yourself tire swings can not only decorate country cottage area but also to diversify the leisure time of children and even adults. Making a swing does not require large financial investments. It is both simple and economical, and gives the opportunity to give a second life to worn-out car tires. For the manufacture of diy tire crafts you only need your imagination, the simplest knowledge at the level of labor lessons and a place for construction. Any economic summer resident has material for the manufacture of simple swings.

Tire selection
for making swings

In order to make a high-quality and durable swing from a tire, you need to choose the material with great care. Products of foreign manufacturers are well suited for this, since domestic tires are too hard, they are difficult to cut and bend. Also, experts note that winter tires are more pliable than summer tires, so to create unusual figures it's better to take one. In order to make it convenient to ride on a swing, the diameter of the tire must be large, but too huge products from tractors will not work - even the strongest branch cannot withstand their weight. In this matter, you will have to rely on common sense and your own sense of proportion. And, of course, the rubber itself must be strong and durable, because children will ride in it, whose safety comes first.

Tire preparation

Before creating crafts for the playground, you must carefully prepare the selected tire. To do this, it must be checked for damage so that it can accurately withstand the weight of an adult. Next, it must be thoroughly washed from dirt, because children will sit on the finished swing, and the cleaner they are, the better. For washing, ordinary dishwashing detergents are used, but ideally, you should use WD40 liquid, which displaces dirt and water from the pores of the material. Tires are cleaned from the outside and inside, after which the remains are washed off with water detergents. To prevent rainwater from collecting inside finished product drainage holes must be made in the bottom of the tire.

Choice of base and fasteners
tire swing

Tire swings are often hung from a branch in the garden. For the safety of the child, the tree and branch should be chosen very carefully. The tree itself should be mature, but not old, without visible flaws and lesions, of sufficient height. The branch should ideally be located at a height of 2.5-3 meters above the ground, there should not be other branches under it that interfere with the movement of the rope. In principle, the swing range of the swing itself depends on the height of the attachment, so for young children it makes sense to attach the rope to lower branches, and as they grow older, use their higher counterparts.

The thickness of the base should be at least 25 centimeters, it is better to choose a branch on which there is flat area, limited on the sides by other branches - if you fix the rope in this place, then the rope will not be able to slide to the sides. A distance of 1 meter from the trunk allows you not to worry that the child will hit it while swinging, but you can’t cling fasteners close to the edge of the branch - this way it can break off.

A rope is quite suitable for fixing crafts from a tire, because rubber does not differ in weight. But it must be strong, durable and wear-resistant, special climbing varieties will do. To extend the life of the rope, it is recommended to cover the rope with covers in places most often affected - around the branch, near the attachment to the tire, in areas where children take it, this will reduce the rate of fiber destruction. In any case, the ropes used in the outdoor playground need to be replaced every 2-3 years.

The rope is thrown over a branch in a selected place, tied with a sea knot, and the ends are later tied to the product itself. At the end of the work, the excess ends are cut off so as not to interfere with the children. If desired, you can use chains, they are more durable, but they injure the tree more.

Manufacture of various types
tire swing

Consider the manufacturing process various types tire swings:

Vertical tire swing

The easiest way to make a place for kids to play with your own hands is to hang the tire vertically, as in the photo. For this you need:

♦ Choose a strong, durable mid-diameter tire.
♦ On one side, screw in eyebolts with your own hands - self-tapping screws with hooks on the head.
♦ Tie the ends of the rope tied to the branch in advance, chains can also be used, they need to be fastened with carabiners.
♦ Install the tire at the right height, it depends on the height of the child, on average there should be about 40 centimeters between the bottom edge and the ground, so the baby can independently climb onto the structure and jump off it safely.
♦ Drill drainage holes in the bottom of the wheel so that any water that gets inside can drain out immediately.
♦ Test the swing for durability.
♦ If necessary, level the ground of the playground under the structure.

Horizontal tire swing

From a strong small tire, you can make a simple comfortable rocking seat. In such a simple "armchair", made by oneself, not only children, but also adults will be happy to ride. To create it you need:

♦ Select and wash a suitable tire.
♦ With the help of eye bolts, make fastenings for a chain or rope on the flat side, if desired, you can make four or three supports, in the first case, wheels are screwed under two bolts on both sides at the same distance, in the second - with angles of 120 degrees along equilateral triangle. The attachment points must be carefully calculated, because otherwise the finished swing will constantly warp.
♦ Attach ropes or chains to the base.
♦ Connect them to the hooks on the wheel, hanging it parallel to the floor.

A simpler version of the manufacture of such a swing in the photo below.

Swing - cradle made of tires

More complex structure, which will decorate the playground. In addition, with a sharp shoe knife, making it yourself is a matter of a couple of hours. In such a cradle it will be especially convenient for very young children, while playing on the playground you will not have to worry about their safety. You will need:

♦ Cut off the top edge of the tire with a knife, leaving the rim intact.
♦ On top of the received "handles" with the help of bolts with your own hands, attach brackets for attaching ropes or chains.
♦ Fasten the ropes on the brackets firmly maritime knots, cut off the remaining ends.
♦ Check the seat for strength.

Swing - a chair made of tires

An excellent attribute not only of the playground, but also of any corner of the recreation can be original armchair from tires, as in the photo. To make it you need:

♦ Cut off one rim from the tire.
♦ Along the perimeter of the second, make a cut to half the circle.
♦ Turn the rubber inside out.
♦ Bring the cut edge of the sidewall behind the rim - this will be the back of the chair, the curved opposite edge turns into a comfortable seat.
♦ The kink point is fixed with bolts.
♦ Eye bolts are screwed into the “armrests” of the chair, chains or a rope are attached to them.
♦ The whole structure is fixed on the base.

Tire rocker

From tires, you can make with your own hands not only a hanging swing, but also a ground rocking chair. For this you need:

♦ Cut the tire in half, getting two halves of the circle.
♦ Coat one half with primer.
♦ Screw a polished board to the tire from the side of the cut with self-tapping screws (see the photo for the method).
♦ Attach two boards on both sides door handles for which the children will hold on while riding.
♦ Paint the product in bright colors.

Almost any garage has old used tires. It’s a pity to throw them away, and the environment suffers from the decomposition of this type of garbage, and hands can’t reach recycling. So the tires are gathering dust in the corner of the garage, taking up space. Meanwhile, they can find very useful application. For example, make a swing and please the children in the yard.

Advantages

Compared to wood and plastic competitors tire swings have a lot of advantages.

• This is a strong and stable attraction that is harder to break.
• They are spacious enough for two adults or three children.
• From tires, you can make several options for the shape of the seat. A creative person with an original imagination can bring the most extraordinary ideas to life.
• The rubber material easily tolerates precipitation, ultraviolet radiation and sudden changes in temperature, so these are more durable designs.
• An important advantage is the cost-effectiveness of the product. If there are unnecessary tires, the creator will only have to spend money on the frame and mounts.
• This is the least traumatic version of the swing. Rubber will soften the blow in case of a fall of a vacationer.
• Even a person who is not particularly famous for his “golden” hands will cope with the manufacture of a swing from tires.

disadvantages

Despite the many advantages of a tire swing compared to its counterparts from other materials, this product also has one drawback that must be taken into account when assembling the attraction. Tires have a heavy mass, and therefore, for the safety of vacationers, it is necessary to use a reinforced frame and reliable fasteners in the manufacture of the swing.

Material selection and preparation

Choosing and preparing material for the manufacture of swings, use the advice of experts.

• As for tires, it is better to give preference to imported options. The fact is that domestic models are too hard, and this will create certain difficulties in the process. They are more difficult to cut and bend.
• It is recommended to choose winter tires, it is more plastic than summer version, and therefore will allow you to make a swing in an unusual shape.
• Suitable for swings large diameter tires, but at the same time it is better to refuse the use of wheels for heavy special equipment, otherwise the design will not withstand the weight of the tires.
• When choosing tires, special attention should be paid to the strength and durability of the material, because the safety of vacationers directly depends on this. You need to make sure that the coating is not damaged.
• Before making a tire, it is necessary to thoroughly rinse it from the outside and inside. It is better to use a special WD40 liquid for this, which removes impurities from the pores, but in general it will do. common remedy for dish washing.

• To rainwater does not accumulate inside future swings, drainage holes should be made in the bottom of the tire.
• When choosing a place for a swing, it is recommended to give preference to adults, but not old ones. tall trees, on the trunk of which there is no damage. It is better that the branch that will be used as a base is at a level of 2.5-3 meters above the ground, below this branch on the trunk there should be no other branches and other elements that can interfere with swinging.
• The minimum thickness of the base is 25 cm. It is better to find a branch, at the end of which, a meter from the tree, there is a horizontal section, bounded on opposite sides by other branches - if you hook the rope in this zone, it will not slip to the sides.
• If installation is to be hanging swing on a rope, it is better to choose special climbing varieties. And swings on chains are also popular. The chain increases the durability of the structure, but can damage the tree.

Manufacturing

Making a children's swing from tires with your own hands is a simple process that will require quality materials and perseverance. To help the novice master, the work process is described step by step depending on the design.

vertical

Swing designs can be both vertical and horizontal. Let's start with the first option.

• Screw eyebolts on one side of the selected tire.
• Tie a rope or chain to the desired branch.
• Connect the ends of the rope with screwed screws. If a chain is used, the ends are fastened with carabiners.
• Fix the tire at the desired level, which is determined by the growth of the child. Usually, approximately 40 cm is left between the tire and the ground surface - this will allow little child independently settle on a swing and jump off easily.
• Drainage holes must be drilled at the bottom of the tire. Thus, rainwater will not be trapped inside the device.
• When the swing is ready, it is recommended to test it for strength on your own, and only after making sure that the structure is safe, offer children to swing.
• If necessary, then you need to level the ground under the swing, remove stones and other objects that may interfere with the operation of the swing and the safety of vacationers.

Horizontal

This design is also not very complicated.

• Install the tie-down fasteners on the flat side of the tire using the eyebolts. If you plan to mount four supports, then screw in two bolts on both sides evenly. If there is a desire to make three supports, then it is necessary to arrange the fasteners along a conditional equilateral triangle with angles of 120 degrees. The distance must be calculated very carefully to avoid skewing future swings.
• Attach a rope or chain to a branch.
• Fasten the ends with bolts, hanging the seat parallel to the ground.

Cradle

This model is suitable for children younger age. For its manufacture it is necessary:

• cut off the top edge of the tire with a knife without touching the rim;
• by means of bolts, attach the brackets for installing a rope or chain;
• tie the ends of the rope with marine knots on the staples, remove useless ends.

Armchair

The swing can take various forms such as armchairs. This model will appeal to both children and adults.

• Cut off one rim from the tire. Do not throw away.
• According to the diameter of the other rim, make a cut on half the circle and turn the product to the inside.
• Close the cut part behind the rim, which should be the back.
• Secure the kink section with bolts.
• Insert the eyebolts into the “armrests”, to which the ends of the rope are attached.
• Hang the device on a branch.

rocking chair

Such a rocking chair made of tires will make your children happy.

• Cut the tire into two halves.
• By means of screws, install a plank to the cut point, which is slightly wider and longer than the edges of the rubber product.
• For safety, you need to attach a handle to the board. One of the options for the handle: make two holes on each side and thread a tight rope. Creative masters can install as a handle steering wheel from the car - so the children will be even more interesting.

Skate for kids

And for the little ones you can make such a swing:

• cut the tire into two halves;
• between the two ends of one of the parts, strengthen the plank;
• attach a handle to the plank on the principle of a bicycle steering wheel.

CARVED CHILDREN'S SWING FROM TIRES
Carved children's swings attract special attention of our kids. They look like snails, from which happy faces of boys and girls look out. Of course, to create carved swing it will take some skill to work with tires and skillful handling of tools. But, as they say, the game is worth the candle! The swing looks not only great, but also safer for kids.






SIMPLE SWING FROM TIRES
Can be done perfectly simple swing from tires: tire plus rope. It remains only to find a place where to hang the swing. But you can complicate the task a bit and come up with other nice ways to attach chains. It will be much more aesthetic and reliable.



SWING FROM CAR TIRES
Very nice, comfortable and reliable look and such a swing made of car tires. Even our four-legged friends cannot refuse such a chic and unusual swing.





CHILDREN'S SWING IN THE FORM OF ANIMAL FIGURINES FROM TIRES
Well, here appearance The swing exceeded all my expectations. It's just a fairy tale given to children. On this funny swing, you can ride a horse across the open space or soar in the sky on a beautiful bird. One can only dream of such swings. But a dream is a dream, and a swing should be done for children. I will be very happy if my selection of children's swings from tires is ever useful to you.

Tires are increasingly being used to create various decorations and not only. These are various animals from tires, and flower beds and much more. The author of the article came up with the idea to create a swing out of tires. This material is good in that it is easily accessible and perfectly cut. And also thanks high strength they can be given a variety of shapes, in this case it is a swing in the form of a horse.

Materials and tools:
- car tire of a suitable size;
- cutting tool(metal scissors, jigsaw, knife, and so on);
- long bolts for creating spacers;
- drill;
- strong rope;
- and other tools.

Manufacturing process

Stage one. swing pattern
First of all, you need to create a template for the future swing. For these purposes, it can be printed and then cut. If you look at the template from above, you can see that it has round shape. But from the bottom it becomes clear how he should be transformed into a horse.
Tire cutting can be done a variety of tools. It all depends on the thickness of the rubber and the complexity of the entire project.

Stage two. Installation of spacers
Bolts with solid threads will be used as spacers. They need to be inserted through the tire and compress it with nuts.
Such spacers should be under the seat and at the withers of the horse. Thanks to this, the swing will become stiffer, and it will be much more comfortable to sit on them. If such bolts cannot be found, they can be replaced with rivers and screws. The main thing at the same time is to round off the edges of nuts and screws, as children can get scratched while riding on such a swing.

To tighten the head, back, mane and saddle in the area where the rope is attached, you need about three or four bolts about 5 cm long.

Stage three. swing hanging
To hang such a swing, only a strong cord is used, and strong knots are tied. A cord is tied to the neck and back of the horse's saddle.

Of course, the greatest moment in the manufacture of such a swing should be given to safety, because children will use them. It is necessary to use wide washers and tighten the nuts well. For reliability, the bolts can be threaded. Also, special attention should be paid to the cord, it should not be too thin.

More than one child will not resist the temptation to ride on such a swing, and this, for sure, will be best place for his games.
Such a swing is designed for small children, weighing no more than 50 grams.

They are easy to manufacture, pleasant to spend time and reliable in use.

What do you need to prepare for the construction of a swing with your own hands? What is the manufacturing technology? Let's talk about it in the article.

Necessary tools and materials

To make a swing you will need:

• tires (1-2 pieces, depending on the type of swing);
• thick rope, thin rope or chain;
• ring bolts.

List continued necessary materials and tools will depend on what you will mount the swing on: on a wooden or metal base.

If on wooden base , you will need:

• three thick wooden beams;
• hammer and nails.

If on metal base:

• three strong metal pipes;
• welding machine.

In addition, you will need a shovel to dig holes for the bases, and rubble to fix them.

Read about how to properly plant a daylily and care for it.

Instructions for making a swing from tires

Step-by-step technology for making a swing from tires

First you need to make a seat. As it, you can use a whole unmodified tire, or you can, by performing simple manipulations, connect two tires and get an almost full-fledged seat.

If you decide to use only one tire, leaving it in its original form, you need to make several holes in it. Usually 3 or 4 holes are made (in the form of a triangle or square) on one of the sides of the tire.

The simplest swings are made from one tire

In the holes you need to fix the rope or chain, depending on your wishes, using bolts with rings. We screw the bolts so that the rings are at the top, and thread the rope through them. It is assumed that the tire will hang horizontally.

Complete swing seat

You can cut a seat out of one tire. To do this, cut off one of the sides of the tire completely, and cut off the second side only by half.

We bend inward that part where the side is not cut off, thereby the free part will lie on its side and will serve as a back. The ring should be fixed with bolts.

In four places we make holes: two from one side and two from the other and screw in the bolts with rings.

We make a comfortable swing from two tires

If you want to make a comfortable swing, you need to arm yourself with a knife and prepare two tires.

Cut off the top and bottom of the tire so that only the ring remains. The same is done with the second tire.

We fold one of the tires in half and put it on the other vertically across so that the back of the folded tire lies on the inside, and the bottom on the outside of the first base tire. Everything must be bolted, giving correct form future swings.

At the end, you need to prepare the rings through which we will thread the rope. The swing is ready, it remains to hang them.

The height of the swing depends on who will swing on it. For a child, they should be hung at the level of the belt so that it is convenient for him to sit down.

Features of mounting a swing on a tree:

1. Find large tree, choose a thick, strong bough at least 15 cm in diameter, located at a height of two to three meters from the ground.
2. Throw one end of the rope (chain) over the bough and fix it in the rings on the swing, do the same with the other side.

Features of mounting a swing on a wooden base:

1. Two thick beams need to be installed in pre-dug holes about 40 cm deep, for strength, fall asleep free place between the bars and the walls of the pits with gravel, tamp and cover with earth.
2. Between them we insert a beam, which will serve as a horizontal support for the swing, it must be firmly fixed with bolts. Metal brackets must be fixed in the crossbar or bolts with rings must be screwed in.
3. We fix the ropes in the rings and the swing is ready.

You can read about how to grow clematis in the garden.

Do you want to create a romantic atmosphere with