Are there traces of adhesive tape on the surface? Let's remove it quickly! How to remove tape - regular and double-sided? How to remove tape from paper wallpaper

How to remove double-sided tape depends on what surface it was applied to. The difficulty lies in the fact that acrylic adhesive is applied to the adhesive tape, which leaves sticky marks. Improvised means in the form of solvents, oils help to peel off the tape plant origin or hair dryer. For each surface, a different method is used, depending on the material from which it is made.

Show all

From walls and doors

There are several ways to unstick Double-sided tape from the wall or door surface:

1. 1. With a hair dryer. The device turns on to the maximum mode and is kept at a distance of several centimeters from the adhesive tape. A stream of hot air is directed to the center and to the edges of the adhesive tape. After the adhesive layer has softened, the film is peeled off with a knife and removed. If part of the layer remains, then it is removed with a sponge dipped in soapy water.
2. 2. Using vinegar, water and soap. Water is taken - 275 ml, vinegar - 60 ml, liquid soap- a few drops. A wet sponge is made in a circular motion.
3. 3. Using an eraser. The rubber is wetted and the surface is wiped with it. The eraser acts as an abrasive on wood, furniture and walls.

From glass

Ways to remove tape from glass:

1. 1. Using sharp objects. Since heat is not applicable to glass, the tape can be torn off with a knife. The main thing is not to scratch.
2. 2. Using cleansing oil or rubbing alcohol.
3. 3. Using a window and mirror cleaner.



With plastic and ceramic tiles

Wipe the tape off the plastic ceramic tiles using the usual available means:

1. 1. Another adhesive tape, which is superimposed on the first one and breaks off with a sharp movement.
2. 2. Vegetable oil with a sponge. It is applied to contaminated plastic and removed with a paper towel after 10 minutes.
3. 3. Medical alcohol. When applied to the surface, greasy stains are also removed.
4. 4. Eraser. You can rub it on the surface, and then remove the dirt with a damp cloth.
5. 5. Hot soapy water. It removes glue residue well.
6. 6. Dishwashing liquid.
7. 7. Heating. A hair dryer will also come in handy.

It should be remembered that when working with a hair dryer, you need to set a moderate speed mode, because the plastic surface may deteriorate.



From the refrigerator

Adhesive tape is removed from the refrigerator in the following ways:

1. 1. With the use of vinegar. If the first time it was not possible to remove traces of adhesive tape, the agent is applied to the refrigerator and left for an hour. Then wipe with a dry cloth.
2. 2. Using soda. It mixes with water to form a paste. The rag is moistened in the solution and traces of glue are removed.
3. 3. Baby oil. A few drops are applied to the surface of the refrigerator. Then wipe with a rag.
4. 4. Razor blade.

The razor needs to be handled very carefully. Any wrong move will result in scratches on the refrigerator.

From paper and wallpaper

Again, you can remove adhesive tape from paper and wallpaper with a hair dryer. To do this, a stream of hot air is directed to the surface. With the other hand, the tape slowly comes off the paper. As it comes off, the air jet is directed to the place of separation. Gradually, all paper will be cleared.

We call duct tape duct tape because it is this trademark first appeared on the markets of our country. The creators named it after English word Scotch - Scotch, which in America of the last century was synonymous with stinginess. The nickname came from users of early samples of the tape, who complained that there was too little adhesive on the cellophane strip. Now we are racking our brains on how to wash this glue from adhesive tape, there are so many of it.

In fact, difficulties in removing the remnants of adhesive tape arise only if you do not know some tricks. Despite the variety of types of this tape, acrylic-based glue is used everywhere. It turns out that the choice of means depends on the material on which the contamination was found.

How to clean tape on plastic

In our homes, plastic is used everywhere: frames, household items, furniture, children's toys and many other items. And before cleaning it from stains, you need to evaluate how good this plastic is. quality material able to withstand more aggressive agents than cheap products. The contact time is also taken into account, because it is much more difficult to separate the old adhesive tape. Of the simple improvised means may come in handy:

• Vegetable oil
• white spirit or gasoline
• ordinary eraser
• Hair dryer

kitchen magic

Oddly enough, removing traces of adhesive tape is easy with any vegetable oil. It mixes with glue, changing its properties. The oil is poured directly onto the contaminated surface or applied to a cloth and applied to the stain for several hours. The mass that has lost its stickiness is erased with a regular napkin, and the surface is washed with soapy water.

Flaws. Unfortunately, this method is not applicable if it is not possible to thoroughly wash the object of oil with water.

Three, three, three and it will be ... clean

School eraser works wonders, removing traces of even the most ancient adhesive tape. Dirt is removed, like pencil marks in an album, and all that remains is to brush off the specks with a damp soft cloth. This method is equally suitable for electrical engineering, and for plastic windows, for furniture or for toys.

Heat up until done

Old glue tightly eats into plastic surfaces. That's why it's important to remove masking tape or protective film as fast as possible. It is better to clean pieces of window plastic construction foam than to wait until, under the influence of the sun and time, the glue and the frame of the double-glazed window merge into a single whole. The above applies to other subjects as well.

If this still happened, then you can try using a hair dryer. From heat, the adhesive mass will soften and come into contact with other cleaning products. The help of a hair dryer is indispensable when removing double sided tape, since in addition to acrylic it contains rubber and various foam materials, dense pieces of which remain on everything to which they have been glued for a long time.

Flaws. A hair dryer is not always at hand, and besides, not every plastic will survive the temperature rise without losing its decorative effect.

Tape damaged furniture

During transportation, drawers and doors of cabinets and cabinets are fixed with adhesive tape, and then they cannot decide how to wash the tape. The tools used here are the same as for plastic, but there are some features of their use.

In everyday life, we often use a popular stationery item, which is adhesive tape. The advantage of its use in convenience, which made given material indispensable assistant at home. When you need to move things to new apartment, boxes, bags are packed with adhesive tape, furniture doors are sealed, objects are attached to each other, they are tied together.

Often, housewives use adhesive tape to insulate frames for the winter. It is very convenient and efficient. But with the advent of spring, the problem of removing the remnants of this item arises. And they are able to accumulate dirt and dust on themselves.

Undoubtedly, adhesive tape is an excellent tool for fastening parts and packaging. But after application it often leaves on surfaces different types sticky trail. And sometimes it's hard to wash it off. But there are many proven and effective ways solutions to such a problem.

Scotch has gained wide popularity in our country. It is used everywhere and for different purposes.

It is worth noting that all types of adhesive tape have acrylic adhesive as a sticky layer. For this reason, suitable components will also be required for removal. It is also important to consider the type of surface being cleaned, because it needs to be preserved. Let's take a closer look at how to eliminate traces of adhesive tape at home.

How to remove tape marks from plastic

Plastic is the most popular material in any home. It is used to produce dishes, furniture, toys and much more. Before telling you how to remove tape marks on plastic, it is important to mention that the quality of the plastic surface is first evaluated. For material High Quality aggressive methods are suitable. To eliminate old traces of adhesive tape, prepare:

gasoline or thinner;
stationery eraser;
vegetable oil;
hairdryer.

The first method will be with the use of oil. It will help to easily eliminate adhesive tape and its traces, because when mixed with glue it has the ability to change its qualities. Apply the oil directly to the traces of glue. If the marks are located on a vertical surface, moisten a cloth with oil and leave it on for a couple of hours. After the loss of stickiness, the mass is removed with napkins. After manipulation, the plastic surface is washed with soap. This option will not work if then it is not possible to properly clean the object from traces of oil.

A simple school eraser helps to remove sticky marks from glasses, furniture and similar items. At the same time, he is able to cope with chronic traces. All stains are removed by the principle of erasing a pencil. Then blow off the specks. The disadvantage of this method is the high labor intensity, because when it becomes necessary to clean large surface, it requires a lot of time and labor costs.

Filtered gasoline, which is used for lighters or white spirit solvent, can effectively remove traces of adhesive tape from any type of plastic surface. They need to be wiped with a cloth or cotton swab dipped in these solutions. After the item is washed with any means. Negative side the use of this method is the aggressiveness of these funds. As a result, with the remnants of glue, you can easily remove and upper layer surfaces. The object then dims, and on it appear light spots. To avoid such excesses, before cleaning, the agent is tested on an inconspicuous part.

When using tape removers, it is important to test them on inconspicuous areas. This is especially true for aggressive methods.

If the adhesive tape is on the object for a long time, then it eats into it. As a result, plastic and tape are connected. This applies to adhesive films. pvc frames windows, glass stickers. In a situation with windows, under the influence of ultraviolet radiation, the tape becomes difficult to remove. In this case, a hair dryer will come to the rescue. Under the influence of heat, the adhesive softens and is influenced by the means. A similar method is effective in removing double-sided adhesive tape.

In addition to glue, it contains foam materials and rubber. They are able to firmly “weld” to surfaces. The negative side of using this option is that not all types of plastic survive high temperature without loss of external beauty.

How to remove tape marks from furniture

On furniture, contamination from such a tape occurs after transportation, because. it winds up and fixes doors and other moving components. In order to remove traces of adhesive tape on furniture, you will need the same helpers as in the previous case. But here it is important to mention the limitations:

oil is allowed to be applied only on the polished surface. If the wood is not treated, it will absorb oil, which will cause greasy spots on furniture;
gasoline and mineral spirits help to effectively clean any type of furniture, but they are used with caution on a painted or polished surface. The reason is that these agents dissolve the coating;
With the help of an eraser you will be able to remove traces of glue on any type of furniture, including glass products. But here, too, the size of pollution acts as a limitation;
a hair dryer is used as a pre-cleaner before applying oil or thinner. It is important to clean plastic, lacquer and glass with care, as temperature may leave white spots on them.

Cleaning equipment from adhesive tape

To clean equipment (washing machines, refrigerators, etc.), it is worth adding to the components mentioned above:

alcohol;
vinegar;
acetone;
window cleaner.

These components are also perfect for washing off unsightly glue particles from popular adhesive tape on mirrors, glass, ceramic and tile surfaces.

Acetone, which is used to create, is able to easily cope with adhesive tape. If, in addition to glue, pieces of adhesive tape remain on the surface of the equipment, then they are moistened with acetone and washed. This option is not acceptable for removing marks on the tinted glass of the car.

Vinegar, alcohol, and window cleaners can not only remove acrylic-based adhesives, but also remove tape residue. The downside is the difficulty in removing old pollution.

From all types of surfaces, adhesive tape is removed with the same components. Be aware of the precautions for use.

It is important to note that the battle with glue spots can easily be automated. So a rubber nozzle or nipple suitable for a tubeless tire is inserted into the drill. This option helps to remove even the remnants of foam adhesive tape without worries. And the processing speed is noticeably increased.

How to remove double sided tape

It is known that such adhesive tape is much stronger than usual, so the question arises of how to remove double-sided tape and not harm furniture or other surfaces. In addition to the fact that the glue in it is stronger, when removed, difficult-to-remove shreds often remain. So, to eliminate traces of such adhesive tape, you will need:

gasoline, alcohol, kerosene or thinner;
rubber nozzle for power tools;
cotton napkin;
hair dryer;
vegetable oil.

If the surface where traces are to be eliminated is resistant to high temperature effects, then it must be warmed up with a hair dryer before the process of removing traces. After that, the adhesive tape is easily peeled off, and the contamination is wiped with a simple cloth.

Such adhesive tape is easily and effectively removed by applying vegetable oil. This option is more suitable if the surface cannot be heated. After applying the oil to the stains, they are easily removed with a solution of soap or dish detergent. The use of gasoline is allowed if the speck of glue is small. But here it is important to minimize the contact of gasoline and the surface.

Remarkably copes with the removal of adhesive traces of various chemistry for the home, because. Today there are many products that are created to remove a variety of stains. And glue is also included. If you prefer such products, then try them first on an inconspicuous area.

Double-sided tape is much denser and more reliable, and therefore the methods of dealing with it are somewhat more aggressive. But here it is important not to overdo it.

In this situation, the function of the eraser is assigned to the rubber pad on the drill. This method is great for cleaning large areas and elimination a large number little spots.

So, let's summarize the results of removing glue and adhesive tape itself from various surfaces:

be sure to purchase a rubber nozzle for a drill. It resembles an eraser and is specifically suitable for eliminating such contaminants. This tool will give you the opportunity to easily and damage the lacquer surface to remove adhesive traces;
if you need to remove glue from the windows, then a powerful cleaner, which is sold in automotive stores, will do. To begin with, the base is removed with a thin knife, and then the areas with glue are wiped with a napkin moistened in the product;

if you need to get rid of double-sided tape from appliances or furniture that is varnished, then use vegetable oil. It is applied to adhesive tape and left for 12 hours, after which the base is removed.

Remember that the sooner you start to deal with duct tape marks, the less effort you will need. Glue over time is able to "solder" with some types of surfaces, which makes it difficult to clean them without damage. In addition, do not forget to test the effect of any of the methods on inconspicuous areas, which will help to avoid damage to expensive pieces of furniture and household appliances.

And, finally, it is worth telling the key advice: use the types of adhesive tape that are suitable for further removal. A specially created adhesive composition makes it possible to remove the adhesive tape even after a long period of time. These adhesive tapes will remove residue-free from most types of hard surfaces. If you need to remove it, you only need to pull the edge, and the tape will peel off without problems and traces.

Double sided tape is very useful thing in the house, but removing it can cause you a lot of trouble. Choice better way removal will depend on the type of surface it was stuck to and may require some trial and error. Continue reading our article where you will learn a few useful tips about removing the double sided tape.

Steps

Removing double-sided tape from walls and doors

Rinse off any excess tape with water, vinegar, and soap. Mix 2 cups (275 milliliters) of water with ¼ cup (60 milliliters) of vinegar and a few drops of liquid soap. Dip a sponge into this solution and then rub desired area walls or doors in small circular motions. This mild cleaning solution should not damage the paint, however you may notice some surface discoloration.

Use a magic eraser (another name for such an eraser is a melamine sponge) to remove any remaining adhesive tape. Dampen a melamine sponge with water and rub it over the desired area until the traces of tape disappear completely. Magic Eraser is a mild abrasive that is unsuitable for use on glass and polished surfaces, but is perfectly safe for walls and doors. However, its use may result in slight discoloration of the surface.

• You can buy a magic eraser in the department detergents supermarket or hardware store.

Removing double sided tape from glass

1. Take everything you need. When removing the double-sided tape from the glass, you cannot use heat, as this may cause the glass to crack. You also cannot use anything abrasive as there is a chance of scratching the glass. The only way out is to remove the adhesive tape with oil. Here is a list of what you will need:

   • Butter knife (you can also do this with nails)
   • window cleaner
   • Sponge and glass cleaner
   • Food or cleansing oil (mineral oil, Goo Gone, etc.)
   • Medical alcohol

2. Try to tear away as much as possible large quantity adhesive tape. You can do this by prying off the corner with your fingernail. You can also use a butter knife or spatula for this purpose, but be careful not to scratch the glass.

   Spray the tape with window cleaner. If you don't have a cleaner, you can make your own by mixing 2 cups (275 milliliters) of water, ¼ cup (60 milliliters) of vinegar, and a few drops of liquid soap.

   Rub the wetted area with a sponge in a circular motion. This will help loosen up any remaining pieces of tape. If the sponge has two sides (soft and abrasive), try using the abrasive side.

   Use oil and a safe glass sponge. If vinegar-based glass cleaner doesn't work, then you need to soak the tape in vegetable oil (like olive oil) or a cleaner (like Goo Gone or Goof Off). Spray the oil on the desired area of ​​the surface and rub it with a sponge until all the tape is gone.

   Clean the glass with alcohol. moisten soft tissue alcohol and wipe the selected area until the tape and oil are gone.

   • The traces remaining from the adhesive tape should be polished with a sponge dipped in oil, and then wiped again with alcohol. The cleanser will remove any remaining adhesive tape and evaporate without leaving any residue.

   Removing double-sided tape from other surfaces

   Use a hair dryer to remove the tape from the paper. Insert the plug into the socket and turn on the hair dryer. Set the blower to medium or strong and direct the hot air to the tape. After a few minutes, try to pry off the tape with your fingernail. This method is especially effective for removing tape from paper.

   • Take extra care when handling photographs, as hot air can damage them.

3. Use cooking oil. It works on the same principle as the commercial products Goo Gone and Goof Off, but contains no harmful chemicals, making it safer to use on plastic surfaces. Just pour some oil on the area to be applied, wait a few minutes, and then wipe it off with a dishwashing sponge.

   • Do not use oil on paper, cardboard or fabric as it will stain.

4. Try using acetone or nail polish remover on bare surfaces. This will dissolve the adhesive layer of the tape and it will be much easier for you to remove it. Acetone, like alcohol, evaporates easily, leaving no residue behind. Unfortunately, it can also dissolve paint on the treated surface, so this product is not suitable for plastic and painted surfaces. Just pour acetone or nail polish remover on the tape, let it soak in for a few minutes, and then try to tear the tape off. This method is most effective on fabric as acetone leaves no residue behind.

   • It can be used on paper and cardboard, however it may wrinkle these materials (as with any other liquid).
   • When using nail polish remover, try to use a clean product without additives such as vitamins and strengthening agents. Also, try not to use multi-colored nail polish remover, otherwise there is a chance of staining the surface being cleaned.

5. On the plastic materials it is recommended to use medical alcohol. It will act as effectively as acetone, but not as aggressive, which means the paint and the surface itself will not be destroyed. You can remove a small amount of the remaining adhesive tape particles with a sponge. This method is very effective for fabric.

6. Removing adhesive residue

   Use oil to remove tape residue from plastic or glass. You can use a vegetable oil like olive oil, mineral oil, or cleaning oils like Goo Gone or Goof Off. Dampen a cotton swab with the oil and rub it into the surface until the tape marks are gone. Moisten another cotton swab with rubbing alcohol and wipe the surface to be cleaned to remove any oily residue.

   • When working with large area horizontal surface you can pour the oil on the desired area and leave it there for a few minutes.
   • Do not use oil on bare wood or walls. Otherwise, the oil will soak into the surface and leave greasy marks.

7. Try using acetone on glass. Do not use acetone on painted, treated or plastic surfaces. It erases paint and corrodes some types of plastic. Minor residues are removed with a cotton swab moistened with acetone by wiping the required area until all traces of adhesive tape are completely removed. For more severe cases, fill an aerosol bottle with acetone, spray it over the desired surface and let it sit for a few minutes before wiping until complete disappearance tape traces.

   • This method can be combined with the oil application method.
   • Acetone is safe on most fabrics, but in any case, you should test it on an inconspicuous area first, as some fabrics may change color when exposed to it.

8. Use rubbing alcohol to remove tape residue from any surface. It is safe to use on walls, plastic, treated and untreated wood, fabric and glass; it should not wash off the paint or damage the surface, but it is possible minor change colors. A solution with a high alcohol content, such as 90%, works more effectively, however, on painted surfaces, it is better to use a liquid with a low content, such as 70%.

   • A smooth surface should be polished with a cotton swab dipped in alcohol until the traces of adhesive tape disappear completely.
   • On a rough surface, use a towel or piece of cloth instead of a cotton swab. This will help prevent fibers from getting into the texture of the treated surface.
   • Alcohol from a spray bottle should be applied to the area with firmly adhered tape residues. Leave the alcohol on for a few minutes and then wipe the surface with a cloth or towel.

There are situations in life when you have to resort to various methods to clean any surface. Very often, traces of adhesive tape appear on furniture, windows and doors. This happens when you need to attach something to a surface. And when the need is gone, you rip off adhesive tape, but the glue from it remains. This is unpleasant not only because the surface becomes sticky, but also because dust and other rubbish stick to it, dirt accumulates. In this article, you will find the answer to the question of how to wipe tape from plastic and several ways to solve this problem.

Remove stains with duct tape

The most common way to remove glue stains from tape is with the tape itself. The principle of kicking out works here. "However, this method does not always work one hundred percent, if, for example, the traces are already old.

If you use this tool, nothing bad will happen to the plastic surface. To remove tape stains on plastic, take any and cut off a small piece. Then, with sharp movements, stick it to the stain and tear it off. You need to do everything quickly so that the tape only has time to grab the glue from the surface, but not stick by itself.

Usually, this method works well with recent pollution. But if the glue cannot be removed, then take more serious measures.

Sunflower oil

How to remove adhesive tape from plastic? The solution to the problem can usually be sunflower oil. You can also use any other vegetable you have at home (olive, linseed, grape), or even essential oils. But still it is more economical to use sunflower for this purpose, since it is the cheapest.

To understand how to wipe marks from adhesive tape from plastic, you need to try several methods and choose the right one. So, pour some oil on a foam sponge or cloth. Put it on the stain and leave it for a while. 15-20 minutes will be enough.

The oil works in the following way. Under its influence, the glue is impregnated and increases in volume, therefore, moves away from the surface.

After the specified time, simply wipe off the remaining dirt with another rag or paper towel. The oil can be easily washed off with ordinary laundry soap.

Now you know how to wipe the adhesive from the adhesive tape from the plastic using vegetable oil. It will help solve the problem on surfaces other than wood.

Wipe off glue with alcohol

Alcohol is universal and effective remedy. Not only will he not harm plastic surface, but also completely cleanse it of impurities.

If you are wondering how you can wipe the adhesive tape from the plastic, look in the first aid kit. In any house there is a medical, ammonia or tincture of alcohol. You can also use vodka.

Alcohol will help not only remove the adhesive from the surface, but also bleach the plastic if it has turned yellow. Take a cotton pad and soak it in alcohol. Apply a stain remover.

Most often, this method is used to clean plastic windows, and not only for frames, but also for glass. Even special means for glasses are made on an alcohol basis.

Remember, never apply alcohol to a painted surface. The product may dissolve the paint.

stationery eraser

Many may not believe it, but the solution to the question of how to wipe the adhesive tape from plastic can be an ordinary stationery eraser or, as it is called in another way, an eraser. It cleans wooden or plastic surfaces easily and simply.

There are no tricks to use here. You just need to take an eraser and rub the glue stain until it disappears. Double-sided erasers or pen erasers work even better as they have a hard structure.

When the contamination is removed, a rubber mark may be left. There is no need to be afraid that a new spot has appeared in place of the old one. It can be easily removed with a damp cloth, preferably made from natural fabrics that absorb moisture well.

Soap

Soap, especially laundry soap, is a folk cleaning agent that has been used since ancient times to clean various pollution. Surprisingly, soap can even remove traces of adhesive tape.

Dilute a little soap in water so that a solution of sufficient concentration is obtained. Now soak a piece of cloth or sponge in the product and rub the dirt left by the tape. If a plastic thing small size and it can be immersed in water, it will be more convenient to leave it for a while in soapy water. So the stain will go away by itself, and you just have to wipe the surface.

Cleaning agent

Among other things, dry washing powder. If there is none in the house, try using soda, it also acts like a scrub.

Of course, if this cleaner is used incorrectly, it can damage the surface, leaving scratches. But there will be no harm if you proceed as follows:

1. Dampen the sponge and sprinkle the powder on it.
2. Press onto the stain and leave for a while to soak the dirt and become more pliable.
3. Gently wipe off the adhesive. You can not rub the stain with force - this is what injures the plastic and any other surface.
4. When finished, wipe with a clean, damp cloth to remove any remaining cleaning powder.

hair dryer

How to get rid of plastic? Probably not many people know that it can be removed with a hair dryer.

So, clean up according to the following steps:

1. Plug in the hair dryer. The main thing is that it reaches the place of pollution.
2. If your hair dryer has several modes, then you need to set it to high power. An average is enough if you are afraid of overheating the device.
3. Now turn on the hair dryer and point it at the double sided tape. You need to hold as much as possible, at least three minutes. Especially warm up the edges of the tape - in these places the adhesive tape sticks most firmly.
4. Turn off the hair dryer, pry off the corner of the tape with a flat plate or fingernail. The adhesive tape should immediately come off about half. You can gently tear it off, or warm it up again so that it moves away by itself.

As a plate, the non-sharp side of a small knife or a children's spatula for plasticine is suitable.

Vinegar soap solution

If you are still thinking about plastic, then improvised tools that are usually found in every home can help you. It's vinegar, soap and water.

Prepare a solution. This will require 270 g of water and 60 g of vinegar. This amount is equivalent to two cups and a quarter of a cup, respectively. Add some liquid soap to the solution.

Using a sponge or cloth soaked in the solution, remove the tape by rubbing the dirt in a circle. Be careful not to rub too long or increase the percentage of vinegar as there is a risk that the surface will fade.

However, you have nothing to fear if the plastic (or any other) surface has White color. From the vinegar-soap solution, it will only look cleaner. By the way, vinegar is widely used in glass cleaning - it not only removes dirt, but also makes the surface shine.

Melamine sponge

There is another tool in the fight against double-sided adhesive tape - this is sometimes called a magic eraser in another way.

All you have to do is soak the melamine sponge in water. Then, simply rub off the remaining adhesive tape or glue residue. The Magic Eraser does a great job of doing this, and you won't have to struggle with getting dirty for long.

This tool is considered a mild abrasive. It must not be used on glass and surfaces that have been polished. However, you can safely clean walls and doors with a melamine sponge. Keep in mind that the magic eraser may slightly discolor the item that needs to be cleaned.

Many are wondering where you can buy this tool, because, perhaps, for some it is new. In fact, a sponge can be bought at regular store household goods or a large household goods supermarket in the cleaning products section.

Thus, do not panic if a trace of adhesive tape or double-sided tape is found on the plastic surface. Use the recommendations of this article, and such pollution will no longer be a problem for you.