Installation of a box in the toilet from plastic panels. Drywall box to the toilet: how to hide the pipe

Any repair in the toilet is always fraught with certain difficulties. They arise due to the special specificity of this room. Therefore, the choice of finishing material for repair here should be given special attention.

Today, as a finishing material in this room can be:

  • ceramic tile;
  • drywall moisture resistant type;
  • plastic;
  • PVC panels;
  • plaster;
  • moisture resistant paint;
  • wallpaper.

All these materials in varying degrees suitable for finishing the toilet. But it is best to use drywall.

The toilet, whether combined with a bathtub or isolated, has some requirements for finishing materials which should be considered when planning the decoration of the room. These requirements include:

  • increased resistance to high humidity;
  • preventing the development of mold and fungi;
  • lack of absorption of odors;
  • maintaining temperature differences;
  • easy care;
  • resistance to mechanical damage.

With all these requirements, finishing the room with drywall perfectly copes.

Finish options

For the toilet, there are several options for trimming drywall sheets:

  • creating only a box to hide unwanted elements in it (sewer and water pipes with counters);
  • wall decoration. This allows you to perfectly level the surface of the walls and greatly simplify the final finishing of the room. Also in this way a partition is created between the bathroom and the toilet;
  • plasterboard ceiling construction. It will allow you to build in additional lighting and make it possible to hide defects in the concrete pavement;
  • complete cladding of the toilet with drywall, including walls, ceiling and the creation of a pipe box.

Finish options

The choice of finish depends entirely on your desires and capabilities.

We design a drawing

To spend everything installation work correctly, you should draw a preliminary drawing of a plasterboard structure, and separately for the box, ceiling and walls. It is also needed if a partition is installed between the toilet and the bathroom.
In any situation, to create a drawing, you must:

  • draw the perimeter of the wall / ceiling;
  • apply the dimensions of the structure, whether it be a partition, a box or a crate of walls and ceilings.

Device diagram

Note! When creating a drawing, consider dimensions such as metal frame, and the width of drywall sheets.

If there is additional lighting in the ceiling, the location of the lamps is also indicated on the diagram.
Do not forget that when mounting the box, you should think in advance about quick access to the pipes. To do this, you can make part of the structure removable or design a door.

Preparatory work

When using drywall to finish the toilet, do next training working space:

  • remove the old finish from the walls / ceiling;
  • replace pipes;
  • process all walls and ceiling special means preventing the appearance of mold and fungus;
  • on the dried surface, apply markings according to the drawing. Be sure to use the level for a more even transfer of lines from the diagram.

Now everything is ready for installation work.

Required Tools

In order to sheathe the toilet with drywall, you will need:

  • drill with drills;
  • perforator;
  • building or water level;
  • tape measure with a pencil.

This set of tools will help you quickly complete the entire finish.

Installation work

Today, there are two ways to finish plasterboard in the toilet:

  • mount a metal frame;
  • glue the sheets to the wall itself.

Let's consider each method in more detail.
The creation of a metal frame occurs according to the following scheme:

  • we apply a guide profile to the lines drawn on the wall;
  • we make holes in it with a puncher;
  • fasten the profile with dowels;

Note! First, we draw the frame around the perimeter, and then we fix the stiffeners.

  • then we mount stiffeners to give the structure greater stability. The step between the profiles is 50 cm.

Finished frame

The partition between the bathroom and the toilet is mounted in a similar way. But in this case, the partition must contain jumpers. They will stabilize the entire structure.
Next, you need to sheathe the resulting structure with plasterboard sheets. To do this, we do the following:

  • if necessary, cut the sheets into pieces of the desired size;
  • we attach them to the frame and fasten them to the screws.

With this design, you can easily hide the pipes running from the ceiling to the floor, without extra costs to create a separate box.
The second method involves the absence of a metal frame, and the material is attached to the walls with adhesives. This option for attaching drywall is more preferable for the toilet. Since the creation of a framework leads to a significant reduction free space and our toilets are often quite narrow anyway. However, you need to be aware that sticking sheets on uneven walls with obvious level differences will be almost impossible.
Installing sheets on walls with adhesives involves the following steps:

  • leveling the walls with plaster;
  • if necessary, cut the sheets into pieces of the required size;
  • apply adhesive to sheets or pieces. Sheets should be processed over the entire surface.

Application of adhesive solution

  • We apply drywall to the wall and press it down. In this state, you should hold the sheet for a certain time, which is necessary for gluing it.

Regardless of the method used, there will still be seams between the drywall sheets. They should be sealed in the following way:

  • we seal all the joints with a sickle - self-adhesive tape;
  • we cover with putty the places of joints and screwing in self-tapping screws;
  • we prime the entire surface of drywall with a deep penetration solution;
  • apply finishing layer putties.

Now we only have the final finish.

The final stage

On final stage finishing the toilet, you should choose the type of finishing material.
Drywall can be finished in the following ways:

  • lay ceramic tiles. This finish is the most common. With tiles, you can create the most varied design premises. Here you can use both small (mosaic) and large tiles;
  • painting with waterproof paint. This method of finishing is suitable in case of creating a partition between the toilet and the bathroom. So the partition will not be too loaded;
  • glue with waterproof wallpaper;
  • finishing artificial stone etc.


Plasterboard tiling

When choosing a material for finishing drywall in a toilet, one should be guided not only by its appearance but also functionality and practicality. Walls must be resistant to cleaning agents and wet cleaning. In addition, they should not contain unnecessary elements that you can hit.
Finishing the toilet can be practical, but at the same time very beautiful. The use of drywall is possible both in a combined bath with a toilet, and in a separate room.

All technical communications in the toilet can be made invisible - such a move instantly transforms the room. Firstly, you will immediately notice that there is more space. This visual trick always works. Secondly, even such a place as a toilet can be not only neat and clean, but beautiful, and even elegant. And this will definitely help the box, which is not at all difficult to build with your own hands in the toilet.

The manufacture of a masking structure begins with a drawing. First determine where exactly to be the box. Measurements can be taken with an ordinary tape measure.

Make a design drawing on paper:

  • Mark with your own hands the places where suspensions with load-bearing profiles will be attached;
  • All attachment points (this is important) must be placed strictly on the same line, forming a continuous whole plane for the edges of the box, otherwise, distortions may form.


Then you can start the work itself. self-tapping screws metal profiles fasten to the hangers - you get a kind of frame for the box. Check if the corners of the profile are right. They must be either strictly vertical or strictly horizontal.

When you are convinced that everything is correct, you can sew up the frame with drywall. And this is done by hand. GCR is fixed with self-tapping screws, and if the plates are light, then you can make it even easier - glue them. But, attention, while the pipes and sheets should not touch in any way!

How to mount a drywall box in a toilet

It all starts, as always, with markup. Marking is done on the floor, and the plumb line will move to the ceiling. The profile is fixed strictly along vertical lines.


If the profile is very long, you can bend it with your own hands so that it is enough for both the floor and the ceiling, but at the same time, be guided by the markings. The preferred dowel pitch is from 600 to 1000 mm.

  • From the profile, cut off a part comparable in length to the box, reduce it by 10 mm, clean one side by 55 cm;
  • Do the same on the other side, the parts are fastened with dowels at the end;
  • Next, make two profiles for the racks, they will refuel into the carrier profiles that are located on the floor and on the ceiling;
  • To make the design more stable, it is better to mount jumpers 600 mm apart;
  • It happens that for greater confidence, the owners decide to make as many as three stiffening belts, then 6 short jumpers and 3 long ones are attached, and they are cut out from the rest of the profile;
  • First, long jumpers are fixed with screws, and only then - short ones.

A box that can close pipes and other communications is ready!

How to sew up pipes in a toilet with drywall

If done step by step instructions to the process of sealing pipes in the toilet, it will be similar to the previous algorithm.


To cover the pipes with drywall, you need:

  • Build box-shaped;
  • Determine the height, width and depth of the structure;
  • Cut off pieces of the profile according to measurements, this can be done with an angle grinder;
  • Connect the profiles with self-tapping screws at a right angle;
  • Screw the frame with dowels to bearing walls, making sure that it does not move;
  • Cut with your own hands the corresponding blanks from drywall;
  • Fix the GKL inserts along the side surfaces to the profiles with self-tapping screws;
  • Build one (or maybe several) holes for the inspection window, it is located at the junction and shutoff valves.

Finishing work is completed. Most often, this is the finishing of drywall with ceramic tiles.


Important points - what can not be wrong

If your task is to close the pipes with drywall sheathing, do not forget that you need to keep free access to closed communications. In the event of a repair or an accident, this measure is simply saving.

Before sheathing, be sure to check the pipes and their condition. While the box is not installed, look for rust on the pipes, or signs of rot. The material from which the transition elements responsible for the supply are made is also important. hot water. They must be identical to the pipes so that during the heating process there is the same level extensions.

Obviously, the construction of boxes in the toilet is quite simple. If the metal profile remains from the previous repair work the more economical the repair will be. It is possible, of course, to represent the skin in the form plastic panels, but drywall construction more durable.

How to close pipes with drywall (video)

Attention, only TODAY!

The eternal difficulty that prevents many at the repair stage is that it is not always possible to hide unnecessary wires or pipes from the eyes. This is the moment that causes a lot of problems and difficulties, and you should think about it in advance. Especially if you have already completed the sewerage stage and pipe replacement.

Now the main task is to hide all the elements and transform the space as much as possible. Let's start with the toilet, where, in addition to pipes, you also need to hide a whole riser. This task is not easy, because it entails a lot of questions. The first of them is how to build a box in the toilet that will be able to hide the shortcomings of this room. It is easy to build if you use drywall. This material widely used for this type of work, since it is easy to work with, its price is always affordable, and its service life is virtually endless.

We find an idea and create a drawing

If you do not have a specific idea of ​​\u200b\u200bwhat such a “locker” might look like, then our photo selection of toilet box ideas will be able to push you to desired option. In fact, you have the opportunity to use any of them that you like more, because all of them can be created absolutely independently, without the participation of masters.

First of all, before purchasing materials, you need to create a diagram (it should not be approximate or approximate), it is important to accurately measure all walls and openings, mark the protrusions, put the drawing and parameters on paper. Keep in mind that the box in the toilet must be installed so that access to the pipes is always open for you, so it is important not to overdo it with disguise.

Materials for the box in the toilet

When you already have calculations in your hands, it's time to buy everything the right materials. You will need:

  • metallic profile;
  • drywall sheets (their number depends on the dimensions of the box itself);
  • dowels and small screws.


Then it all depends on how many elements your "box" consists of. Making a frame is not easy, so there is a special video material just for you, which describes well all the stages of work that are performed during the installation of the box in the toilet.

Here you will learn everything important, but focus on the main thing - the distance from the pipe to the sash should vary from 4 to 5 cm. In addition to everything, stick to the chosen geometry, use a level, mount each element in turn. It is necessary to sheathe the walls so that there are no gaps and cracks - then the drywall box will look beautiful and will not stand out from general view toilet.

Nuances

Most often, ordinary drywall is laid over tiles the same color as the entire interior of the toilet - this way you get a single space, made in the same style. You definitely need to know that installing a box in a toilet is a short-term job that does not require special skills; tiling can be much more difficult for you.

One way or another, but we hope that with our help you will be able to make a box in the toilet with your own hands without unnecessary difficulties and problems. Good luck!

Toilet and bathroom - the premises are small, require a special approach due to high humidity and lots of communications. The difficulty is to beautifully and ergonomically disguise the pipes. One of the simplest and available ways- a box of moisture-resistant drywall.

Box Benefits

A toilet and a bathroom with open pipes look unaesthetic, but the plus is that communications are repairable at any time. Having cemented them with your own hands or giving such an instruction to the workers, be prepared for the fact that the elimination of any damage or defect will be accompanied by a bunch of dust, dirt, violation of the integrity of the finish coating and other troubles. Shtroblenie also carries a certain danger, because there is a risk of damage to the floors. There are many more nuances, but even this is enough to experienced craftsmen recommended to customers to make a light box from moisture-resistant sheets of GKL, GVL, LSU with subsequent finishing with ceramic tiles, wallpaper or painting.

There are several more advantages of such a drywall construction:

1. The device of inspection hatches. You can build a cover for such an opening yourself from a conventional plastic panel or a PVC sheet for prefabricated systems. The latter are used for advertising signs and the like. The technology is simple, installation will not take much time, but the complex looks neat and aesthetically pleasing. In addition, ready-made inspection hatches from a heat-resistant or impact-resistant plastic composite that is painted, wallpapered or decorated with tiles. Products are supplied with a loop mechanism of open or closed type. In the first case, the lid is equipped with a handle for opening, in the second, it is enough to press it a little so that the door opens and moves to the side.

2. Quick dismantling to fix breakdowns. It is enough to remove a few tiles and unscrew the screws to disassemble the structure. In case of careless handling, the finish will have to be restored again, but it will take no more than 1 hour, even if you do everything yourself.

3. Ergonomics. A drywall box can be used as additional shelves for household items.

4. Availability. Price square meter drywall sheet, profiles and hardware fit into the amount of up to 1000 rubles.

Instructions and necessary tools

Looking at the finished boxes, it becomes clear that the technology is simple and unpretentious. But there are some tricks. Firstly, installation is carried out on rough coatings, that is, after the screed is equipped and the walls are plastered, but the tile has not yet been installed. This approach allows you to make the box even, the seams more invisible, and almost perfectly fit ceramic tiles to each other.

Secondly, before proceeding with the purchase of materials, you need to make a plan. If you have instructions in front of your eyes, the work will be done quickly and correctly.

A ready-made drywall camouflage box scheme found on the Internet is unlikely to suit you. It all depends on the features of your bathroom. Therefore, the first thing to do is to draw a plan of the rooms (toilet and bathroom) on a scale, indicate the location of the pipes and determine the design features. In particular, whether sound insulation or heaters will be used to prevent the formation of condensate, where exactly should the inspection hatch be located. The distance between the frame and the pipe, the location of the stiffeners and other issues should also be taken into account.

Based on the above, a drawing is being built future system from drywall. It is desirable that the diagram be drawn up as detailed as possible, indicating the locations of all elements. This will help to accurately calculate the amount of building materials needed.

In order to construct a box in a drywall toilet, you will need the following tools and components:

1. Electric drill or puncher, screwdriver.

2. Hammer, screwdrivers, metal shears and a drywall sheet knife.

3. Roulette, hydraulic level or laser level, construction pencil.

4. Spatula, regular and notched, for applying tile adhesive.

5. Aluminum profile for GKL bearing (guides) and rack. If you are not sure or do not know how to choose them correctly, then it is better to consult with the drywall and accessories seller what types of profiles are needed.

6. Moisture-resistant wall plasterboard, at least 12 mm thick (Lafarge, Knauf).

7. Hardware: dowels, metal screws, screws for drywall sheets.

8. Putty for leveling joints and reinforcing tape.

9. Finishing material:

  • ceramic tiles, thin-layer tile adhesive, mounting crosses and grout for tile joints;
  • wallpaper and glue;
  • paint, rollers or brushes, paint tray;
  • panels and hardware, plastic corner.

10. Primer adhesive.

11. Revision hatch or plastic door with decorative corners.

12. Sound or thermal insulation material. You can use rigid "shells" made of foamed polyethylene, stone or glass wool, or special soundproofing sheets (Shumanet, Vibrostek and others). If the neighbors from above are sloppy and there is a risk of flooding, then it is advisable to do the following: purchase large plastic bags and pack the heat insulator in them. In this way, mineral wool will not get wet and will not dust.

Stage 1. Frame formation.

The scheme of the drywall box resembles a U-shaped "package". For the "skeleton" you need to cut to size required amount profiles. Along the axes (horizontal and vertical), guides are screwed to the wall and floor, which will mark the boundaries of the future box. If the walls are strong, then you can first drill holes for the dowel-nails with a puncher. The step between the hardware is 40-60 cm.

From the support rails, the last profile is vertically installed - the central one, forming an angle. Between the main guides, short segments are fixed every 50-60 cm with metal screws - these are the so-called stiffeners. If necessary, gaps are left in the frame for the release of pipes or piping. The evenness of the structure is checked with a level.

The installation of the frame ends with insulation or sound insulation. The selected material should be tightly laid inside the "skeleton" and, if necessary, fixed.

Stage 2. Sheathing with sheets of drywall.

It is desirable to pre-cut the GKL, including a hole for inspection hatches. Correct installation also involves sawing the joint areas at an angle of 45 °. This will make the connection more accurate and economical.

The cut parts of drywall are screwed with “bugs” screws in increments of 30-50 cm with a screwdriver or a screwdriver. All gaps are filled with putty and reinforced special tape from fiberglass. Further on the surface is carried out finishing: tile, wallpaper, plastic panels, etc.

At the very end, a cover for revision holes is installed. If aesthetic requirements are high, you can do decorative cladding plastic to match the color of the rest of the tile using self-adhesive film or fine ceramics.

It takes no more than a few hours to install a drywall box without finishing. Before the final finishing works it is desirable to withstand a technological break of up to 24 hours to dry the putty and primer composition.

Article rating:

Articles

It plays an important role in the house, as many believe. If it is clean and comfortable, you and your guests will enjoy visiting it. Toilets with mold on the walls and rusty pipes are a thing of the past. Today there are just a lot of opportunities to make this room more beautiful and attractive.

There are pipes and other technical communications in the toilet, which seriously spoil the look and overall impression of even the most beautiful design.

A drywall pipe box will help hide all the sewerage systems and electrical wiring that stand out from the general picture in the toilet. Drywall in the building material market has long occupied a leading position and is in great demand, because it can be used to make beautiful and good repair including in the toilet.

Installation of drywall boxes in the toilet

First of all, you need to decide where it will be mounted - on the wall or ceiling. Its construction will include four successive stages: design, installation of a metal profile, fastening of the plasterboard, final finishing.

For work you will need:

  • knife for cutting GKL sheets;
  • saw blade;
  • disc cutter;
  • metal scissors;
  • pencil, tape measure;
  • drill driver;
  • level;
  • a hammer;
  • electric planer;
  • glue, dowels, self-tapping screws;
  • metal profile;
  • drywall.

First, you mark the lines on the walls, floor, ceiling along which you will mount the profile guides. Then you screw them, forming the necessary bends and turns, onto self-tapping screws. And only after that you can proceed with the installation of drywall sheets. We also fasten them to self-tapping screws with small distances. Light sheets can be planted on glue.

When installing drywall boxes in the toilet, they usually try to hide communications in the formed niche. Actually, the whole box is built around pipes. All joints on drywall are masked with 1-2 mm putty, and the corners are glued with putty corners.

To access the pipes without disassembling the box, you need to make a hinged door, disguised as a continuation of the box. She hangs on door hinges embedded in a wooden beam.

The final finishing of the box is usually made in the same style as the walls. Usually tiles are laid on the walls in the toilet, the box is also lined with tiles of the same color.

Eventually finished construction looks much neater and more aesthetically pleasing than bare pipes. In addition, the resulting step can be used as a shelf for various household chemicals and other toiletries.

Fitting © 2023 Design and interior of apartments