Kitchen furniture with their own hands. Features of self-assembly of a kitchen corner set Homemade kitchen at home

The L-shaped arrangement of furniture is appropriate for any area, and for small kitchens she is completely irreplaceable. The corner set is easiest to just buy, but you can make and assemble it yourself. What for? The second method has significant advantages:

• A self-made kitchen will cost you 2-3 times cheaper than a factory one. Facades, laminated chipboard, MDF, accessories for every taste are presented on the market, and cutting of the material can often be done in the same store;
• In addition, you can make your own custom cuisine, which will exactly match the room and your requirements for spaciousness and design;

• And if you do everything right, then appearance, ergonomics and durability kitchen cabinet worth the time and effort spent. In addition, this work will be pleasant and interesting for you, and your loved ones will be grateful and proud!

It is impossible to describe in detail all the nuances of the work in one article, if you are a beginner, we advise you to get acquainted with the website of the famous furniture maker Andrey Lappo and look at Vitaly Luzhetsky's Youtube channel. And we will describe the general sequence, give advice, useful links, a selection of videos, as well as photo examples of work with cost estimates. Perhaps we will start with them.

Stage 1. Planning - drawing up drawings, thinking through the design, measurements

So, suppose you have already planned the design, color, additional features (like the same drawers in the plinth) and a place for your future. corner headset. Next, you need to take measurements, and then design a drawing with the data obtained.

Before taking measurements, you should determine the configuration of the corner kitchen set which may include:

• Corner sink and cabinet under it;
• At least 2 cabinets to the left and right of the sink cabinet. They can be niches for, or they can just be storage cabinets;
• Upper sections (2-5 or more cabinets);
• Places for stationary equipment - refrigerators, stoves, etc.

Advice! Vertical measurements are necessarily carried out at three points - in the middle, along the plinth, under the ceiling. This will level out the difference in measurements due to the curvature of the walls.

Designing, executing elements and assembling a kitchen is real, even if you only have the simplest circuit, drawn on graph paper or on a sheet of notebook in a cage, where, for example, 1 cell corresponds to 10 cm. But it is better to make a thoughtful drawing, that is, a full-fledged three-dimensional color project, using a special program, for example, "PRO100".

When drawing up a drawing, you will also need to take into account the place where the gas pipe is inserted and the place where the hood is installed (passing the air duct). A diagram or drawing is created with maximum detail, after which a material cutting map is drawn up. And for it, in turn, you need a list of assembly parts for each module. As a rule, to assemble a cabinet, you will need:

• Top;
• 2 side walls;
• Shelves;
• facades;
• Back wall made of light but durable chipboard;
• Edge (with a margin of 12%).

And, of course, the kitchen should have a countertop and an apron.

Stage 2. We purchase materials, make a cutting map, detailing and order a cut

Now we need to buy everything necessary materials, draw up a cutting map and detailing, and then order a cut. The cut material will be ready in 2-3 working days.

Advice! Sawing is better to order in the same store where you bought chipboard, and not elsewhere. It is much more convenient and cheaper - you will not need to order delivery 2 times.

A cutting chart is a documentation that reflects which parts need to be sawn from a chipboard sheet. The map allows you to: see how you can lay out the parts on a sheet, how much residue you get after cutting, and determine how much material you need to make a corner set with your own hands.

You can make a cutting map yourself in special programs, for example, in the Cutting program, or you can order it in the same store where you buy chipboard.

The nuances in drawing up a cut map are as follows:

1. Mounted modules of frame furniture are best made from chipboard 16 mm thick.
2. For modules installed below, on the floor, chipboard 18 mm is used.
3. Width wall cabinets selected from standard model range- 200, 250, 300 mm and so on (dimensions are multiples of 50 mm).
4. To make the back wall of fiberboard, you need to reduce its dimensions compared to the module parameters by 4 mm.

Advice! Most craftsmen prefer BLUM brand fittings.

Stage 3. Preparation of surfaces and tools

Assembly corner kitchen necessarily provides preparatory stage. So, all surfaces along which the furniture will be located must be made even, and the walls at the junction of the headset must converge at a right angle. In order to assemble a corner set, you will need not only a detailed detailed scheme, but also an appropriate tool:

• A hammer;
• Pliers;
• Ruler-gon;
• Jigsaw and circular saw;
• Roulette;
• Knife, awl;
• Level;
• Screwdriver;
• Perforator;
• Hex key for fasteners;
• Drills with a diameter of 4.5 mm, 7 mm, 8 mm;
• Confirmations (50x7) or self-tapping screws 3x16, 3x30;
• Hairdryer or iron for gluing the edge;
• Conductor (not necessary, but highly desirable! Assembly will be easy and of high quality).

Advice! To install confirmations, holes are first drilled in the parts to be joined, and then fasteners are screwed in with a screwdriver.

Stage 4. We assemble the corner cabinet

When the drawing is completely ready and refined, and all the elements for assembly are prepared, the most important stage begins - the assembly of the corner pedestal with a sink. It is always collected first, and therefore the process is carried out with the utmost responsibility and care. Then, on the basis of the installed corner pedestal, you can make a ready-made headset by attaching the appropriate elements to it.

The main structural nuances of the corner pedestal are:

• A hole in the countertop (almost always this cabinet is made with a sink);
• Holes in the side or rear wall for the passage of pipelines supplying water to the sink, under the drain outlet.

These holes are necessary if corner cabinet with a sink has back and lateral walls from a chipboard or fiberboard. But it is also possible that the side walls in this element are not provided, and the rigidity is provided by special connecting posts.

Stage 5. We collect the remaining elements of the kitchen set

After the corner cabinet is assembled and installed, it will be possible to make the remaining elements using pre-made drawings. The sequence of actions in this case is as follows:

1. To assemble the main box and side pedestals are sorted the right details and they have places for fasteners.

1. The panels are fastened together, legs and rails are installed for drawer systems. To make it easy to assemble elements with retractable guides, you must first assemble three walls of the box, insert them into the bottom of the fiberboard, and then fix the facade through an eccentric coupler - so that the sleeve in the side wall grabs the screw head with facade panel. The rollers on the guides must be at the back - this is required by the drawing. Already assembled box placed in a cabinet, inserting it there at a slight angle.

Adviсe:

• Wooden dowels used as fasteners in non-through holes are recommended to be put on glue;
• The joints of the walls of the boxes can be treated with silicone so that the chipboard does not swell and crumble from moisture.

1. Edging can be ordered from specialized companies along with sawing, or you can do it yourself. Glue the edge to the visible ends of the chipboard suitable color, ironing it with an iron in silk ironing mode, that is, on 2k. Cut off the excess edges around the edges with a clerical knife.

1. Mark the countertop plate and cut it. The joints must be treated with sealant, and the ends are closed with a strong metal bar.

1. Wall cabinets can be fixed with mounting plate- one part of it is fixed on the wall, and the second - from the back wall of the cabinet. However, the drawings may include the usual loops.

1. Then you need to install facades.

1. It remains to build the technique into niches.

1. The final stage of assembly is the installation of decorative plugs for fasteners and plastic plinth hiding the gap between the wall and the countertop.

To make with your own hands wooden furniture to the kitchen, first you need to decide what kind of wood you will work with as the main material. Modern market offers more than 40 types of wood - hard and soft. Hardwoods include oak, beech, walnut, yew - their wood is more durable, but it is also more difficult to process them, so they are ideal for the manufacture of solid arrays and slabs. Of the soft ones, you can choose pine, spruce, poplar - they have a smaller margin of safety, but they are easy to process and can be used to design shelves, small cabinets and individual decorative elements. And, of course, the selected material must be of high quality, thoroughly dried and dense, without knots, cracks and layers. AT wooden house a DIY kitchen made from the same type of wood as the house itself will look especially good.

Step two. We choose a project and take measurements.

In choosing a project, you can rely on your own imagination or trust professional designers. In addition, you can use Internet resources and choose one of standard projects taking into account the dimensions of your kitchen and your wishes.

For measurements, clean kitchen space and take a roll. Measurements are taken at 3 points - near the ceiling, at a height of 5-10 cm from the floor and at shoulder level. By the way, it is at this stage that it is already important to know what kind of wood set you will create - if it is ordinary direct furniture, then we will get by with one tape measure, but if we plan corner structures, then it would be better to use a laser rangefinder.

Thus, we calculate the total amount of material required in square meters, not forgetting the back and bottom surfaces, doors, finishing elements, and so on.

Step three. We buy materials, prepare tools.

Having decided on the material and its volumes, you should take care of the tool. In this case, to make the kitchen step by step, you will need:

- electric drill and electric jigsaw;

– rule/level;

- construction meter / laser rangefinder;

- file, screwdriver, pliers and hammer;

- hacksaw;

- screwdriver;

- emery material / planer;

- a jig with a drill for holes for dowels.

Step four. We make sketches and necessary drawings.

Again, you can try to do everything yourself or resort to the services of specialists in 3D design, as well as independently use one of the existing graphic design programs– PRO100, AutoCad or Basis furniture maker. (To save money, you can contact the students of specialized institutions - you can get unique drawings for a reasonable price).

Step five. We prepare and collect parts.

First, we cut out the base of the furniture from a solid array, process the surface and ends, drill holes for fasteners. It is advisable to mark each sawn part in some way, so that later during assembly you do not get confused in them. Cutting accuracy is very important - even a few millimeters of error can play a bad role, but the parts will still be polished, which will also slightly reduce their dimensions.

After the main grinding, you can start assembling furniture. We distribute all parts into upper and lower, main and additional. We form the main frame, look at the tightness of the flaps. For example, you can organize the assembly on dowels and euro screws using a Phillips screwdriver and a screwdriver.

If everything fits together, there are no gaps and inaccuracies, we disassemble the furniture, subject it to final fine grinding, treat it with antiseptic solutions and varnish each part separately, preferably in three layers.

When everything dries, we assemble the entire structure and install it in the prepared place. First, cabinets are hung at the top, then the main furniture and lower structures are installed according to the level, fittings are screwed and hung, and a cornice is mounted if desired.

Beautiful wooden table for the kitchen - do it yourself!

For a better understanding of the process, you can consider in detail independent production dining table (pictured).

To do dinner table with your own hands, edged boards will come in handy. If you want to have a solid wood table in your kitchen standard sizes 0.6x1 m, then you will need about 4 boards 50x150 mm. Excellent material the table will be oak or beech, but if you are a beginner, it would be better to prefer spruce or pine, they are easier to work with.

Scheme of work on the tabletop.

1. We mark and cut the boards at a right angle to align them in length.

2. Properly arrange the wood (alternating boards, the rings of which increase downwards with those in which they decrease, will avoid significant gaps after the boards dry).

3. We process the ends with a jointer.

4. We connect the structure in one of the ways: nails, screws, glue, furniture dowels and the like at your discretion.

5. If glue was used, dry the surface until the characteristic traces disappear.

6. Once again we process with a jointer, and after that with sandpaper, we round off sharp corners.

Let's move on to the table legs.

You can make them from the same edged boards. We choose an arbitrary form. The usual working height from the floor level to the countertop is about 80 cm. We make one leg for example and, using this sample, we cut three more of the same with an accuracy of a couple of millimeters. If you want sophistication and sophistication, the legs can be processed with a milling cutter.

Further, the legs are set around the perimeter and connected by jumpers, which are made of timber or boards and fastened under the table with glue or dowels. Similarly, legs are attached to the jumpers to the table top.

In the final, we process the table with stain and open it with varnish in 2-3 layers. After drying, your new kitchen table ready to use!

For beginners, it will be useful to familiarize yourself with the training video.

It is interesting that a person who has money did everything with his own hands ..

And I got great results..

This kitchen was not made by a professional furniture maker or cabinet maker,

Everything about Blum products is great. Use the proprietary Blum Dynalog program - it will do everything for you and, as a result, you will receive drawings with all the markings necessary for installing fittings:

I will describe the design details below, using the example of photographs of finished products.

Purchase of kitchen appliances

I recommend that you do not leave this step to the end. At a minimum, it is desirable, if not to buy, then at least to clearly define what you will buy later and download all the documentation for these products. Oven, stove, sink - although they are made according to some kitchen standards, but may have design features. Making a kitchen without even imagining what kind of equipment you will put there is wrong, you are tormented. For example, I didn’t take everything into account with the oven - therefore, instead of the facade under the oven, you still see a hole (you need to slightly mill the facade until you master it).

I bought an oven and induction hob Gorenje, Eleyus hood, Franke Java sink, faucet with Grohe Blue filtration system (the first in Ukraine in this design, by the way). 3200$

firewood order(chipboard, fiberboard, facades)

Previously, I sincerely believed that the production of furniture meant large workshops, expensive machines, dozens of people. It happens, of course, and so, but many work in garages. In order to produce furniture, you do not need to cut chipboard and make facades - this is exactly what dozens of people do in large workshops on expensive machines. We are on our way there.

The result of the design should be an Excel file containing a list of all the panels we need. Here's one:

In a relationship board materials, my choice was:
Chipboard Egger Cappuccino 18mm as body material
Chipboard Egger Platinum White 16mm as drawer material
Fiberboard Egger for cabinet backs
Painted MDF as facades

Now look, what a nuance. The company we are going to has a chipboard warehouse program - these are the options for thicknesses and colors that they keep in stock all the time. large quantities. If the chipboard that you need is present in the warehouse program - everything is OK, you will pay for so much square meters how much you need. But if not included - you have to buy chipboard sheets. One sheet, in the case of chipboard Egger, is 5.8 sq.m. And if you need 6.3 sq.m. still have to buy two sheets.

Companies that are engaged in cutting and edging chipboard, the production of facades, today can be found in almost any regional center countries. You give them blueprints and money. They are for you - all your firewood in a packaged form with delivery even to an apartment.

Cutting and edging chipboard, fiberboard, facades, delivery - all this cost me $ 650.

Hardware order(handles, legs, tandem boxes, etc.)

No problem. But it’s better not to scour all sorts of Leroy Marlins, since there are mostly unworthy mass markets. It is better to find a decent furniture fitting company with a large assortment and buy everything there.

I bought:
12 drawer sets full extension Blum Tandembox Intivo
2 hinges + bluemotion for under-washbasin door
1 roll-out grid with a closer under the oven
All this cost $1200

Purchasing a tool

In general, any handy kid already has some tools.
I had to buy a Makita screwdriver, a Bosch jigsaw, clamps and a Wolfcraft welder.

I will immediately warn you - there is nothing to do without a screwdriver in assembling furniture. There's absolutely great amount screws. And Chinese disposable crafts for 40 bucks will not help you. A screwdriver for a man is like a dildo for a woman. Don't be stingy. Please yourself. Come in handy.

So, at the beginning of the process we have:

First of all, we will take the firewood to the balcony and sort it into cabinets. Fortunately, each item has a sticker corresponding to the part number in the above parts list:

Well, let's start assembling. Almost all Italian cabinet furniture is assembled on dowels (chopiki) - the advantage of this method is that no parts of the fasteners climb out, the disadvantage is that the furniture assembled on dowels is non-separable. For such purposes, furniture makers prefer confirmation - it is much less demanding in terms of tolerances.

The connection on the dowels requires an accuracy of fitting the reciprocal holes of 0.5 millimeters. This result can be achieved without using special tool but with huge hemorrhoids. So I bought this tool:

We drill the first holes in the side of the cabinet:

So, our task is to assemble the first cabinet and understand whether our hands are growing from the ass, or still from the shoulders.

We take the sidewall, we will make holes that will be connected to the bottom with dowels. Pay attention to the drilling depth gauge on the drill. What it is for, I hope it is not necessary to explain. Bzzzin:

Here's what we got:

Holes on the sides - 40 mm. from the edges, center in the middle. Sidewall width (it matters, I'll tell you later) - 560 mm. The welder works in the mode of both drilling reciprocal holes and copying. Copy to the second side. This is the principle of operation of the filler for drilling reciprocal holes, I show on the example of the drawer:

Let me remind you that when connecting to dowels, the accuracy of drilling the reciprocal holes (plus or minus half a millimeter) is important. With these tools, I have never had a problem with this - the parts fit into each other (groaning) with little effort. This device costs nothing - 40 bucks. It will greatly save your time - I, for the sake of interest, tried to do manual marking on the test pieces Chipboard is many times more time and a much higher probability of error.

Here is the bottom of the box with counter holes already drilled for the sidewalls:

We drilled 20 holes and voila, our hands do not grow out of the ass:

Okay, let's move on. Now we need to equip the cabinet with closers, legs and a back wall made of fiberboard.
There is nothing complicated in mounting closers - all in the same Blum Dynalog program, you get the exact dimensions of the points where the guides will be attached. One rule applies here - measure seven times, cut one:

Just like two and two. If you make a mistake within 3 millimeters, everything will still work fine. This is a wonderful technique.

Mounting the legs is also not difficult. The main thing is to set yourself a standard for their location and follow it on all pedestals:

Another pedestal (the widest, 80 cm) is ripe. It already has guides and legs.

You should not worry at all due to some fragility of the product - as soon as the back wall is mounted - the cabinet will be filled with pleasant strength. Shown here First stage back fixings - the bottom is fastened with two screws on the sides, the diagonals and angles are measured, the top is fastened with a clamp to the side. Now you can safely peel the screws (after making a preliminary drilling with a two-millimeter drill):

Well, as if there is already progress:

Preparing facades. On the left side of the façade is a drilling jig (the same Wolfcraft), to the right is a hand drill:

Here a jigsaw came into play - I sawed holes for sockets with it, after which I asked for an open cut. Well, I hung the filter control unit and the holder of the filter itself:

When all the cabinets were ready, it was time to reunite them. At this stage, it is important, by adjusting the legs, to bring them into level - that is, the top of the cabinets should lie in the same plane. We clamp the cabinets together with clamps, and be sure to make a “lining” - wooden block into which the drill will exit. If this is not done, there will be serious chips at the exit hole.

I brought a countertop, Luxeform Boston 38 mm. I asked to make cutouts, they did, but look how original (did I put the commas correctly, in general?):

Basically, they are right. Transporting a massive table with a full cutout is a risk - it can break. I had to work with a jigsaw. The cut must be covered with silicone - open chipboard end will quickly swell if this is not done. Well, here you can also see how the issue with an obtuse angle was resolved - everything is very simply leveled. Naturally, I previously made a drawing with geometry calculation.

Today, the kitchen is the place where the whole family most often comes together. Long gone are the days when the entire population of the apartment gathered in the living room in front of the TV. The fact is that now it has become more convenient to find all the movies and programs to your liking on computers or tablets. Nevertheless, a common breakfast, dinner, and just evening gatherings with tea remained, that is, the importance of this room cannot be underestimated. Naturally, all of the above does not apply to those people whose apartments have a separate dining room. In addition, food preparation and storage of all utensils are also very important, and convenience and comfort cannot be neglected in this regard.

How to make a kitchen with your own hands. Step-by-step instruction

Now we will not analyze the situation when the room intended for the kitchen is not prepared for this purpose at all - that is, there are no pipes, electricity and other things in it.

It is best to take for reality a room with which you can work. Walls have already been erected in it, laid flooring, the ceiling is made and communications are carried out.

Planning

First of all, draw a plan of the room on paper. First, a general one is created, since it will be necessary to measure the height and width of the walls, any walls, window sill gaps, etc. (the latter, by the way, can later be used as part of the countertop). In addition to all of the above, household communications should also be included in the plan. It should indicate where there is wiring, where the gas pipe goes, and also note the water supply and more.

But before you wonder how to make a kitchen with your own hands, you need to decide on its shape. It can be linear, that is, lined up along one wall, L-shaped or corner, or U-shaped. The latter type is usually chosen when a room with a separate entrance is allocated for the kitchen.

Already now, decide where you will store the dishes, where you will put the refrigerator, where you will place the work surfaces, stove, sink, and also how the cabinets will stand. Naturally, the plate should be placed closer to gas pipe, a refrigerator or an electric stove - to sockets, and a sink - closer to the water supply. This is logical, so you can avoid unnecessary costs.

Drawing of the future kitchen

Here you need to display all the products that will be used. That is, each bedside table, cabinet and sink must be drawn. Dimensions also need to be affixed - this avoids confusion. Particular attention should be paid to the height of the countertop. It is determined by the height of the person who will most often work in the kitchen. You also need to correlate the dimensions of future bedside tables, drawers, tables and stoves with the countertop.

It should be displayed in the drawing what materials the future pieces of furniture will be made of, not only their facades, but also the frames. Again, the countertop needs special attention. Then, separately, choose household appliances.

There is a way to make your choice easier. It will come in handy, because in a two-dimensional drawing it is not always possible to determine how certain devices, surfaces, etc. will look. Therefore, you can use fashion magazines, or ask friends whose existing options designs you like, how to make a kitchen with your own hands. Photos from magazines will help you deal with many difficulties. Suitable design will definitely be found. In addition, today there are a sufficient number of programs, having worked with which, you can create a three-dimensional, even interactive, kitchen drawing. No special skills are required here (if you have already old enough children who understand computers, entrust it to them. This way you can save time and let the children know that they are trusted).

Materials for making furniture

How to make a kitchen with your own hands so that it is durable, comfortable and of high quality? In fact, there is nothing complicated here. The easiest way will be with lockers, which, in fact, you need to do yourself.

Sidewalls are best made from 16 mm MDF - it is suitable for both cabinets and shelves or cabinets. Side walls boxes can be made from half-centimeter fiberboard. The main thing is to purchase its laminated version. Back walls can be made from plywood - they are the most unused, and indeed remain almost invisible. In addition, if any problems arise, they are easy to remove or replace. Doors, if you do not have the proper experience, it is better to buy separately - they are sold in construction supermarkets, and therefore this will not be a particular problem (and it is better to pick up doors first, and only then make cabinets, instead of adjusting everything at the last moment).

A separate issue is the countertop. It is also best to purchase it separately. It will be good here a natural stone or material similar in composition and properties. If you want to do this yourself, then you can use a thick chipboard, about three centimeters (but a little more is better). Before installation, you need to cover it with several layers. protective equipment so that the tree is not damaged due to excess moisture.

In addition, you will need all sorts of fittings - the list is quite long. Here are euro screws, and hinges with handles, ball or roller guides, legs for cabinets, edges, as well as shelf supports, and, of course, corners. The most important thing here is not to forget to buy something. These are all trifles, but they can become decisive in the question of how to do it. cozy kitchen with your own hands.

Even more important is the acquisition household appliances- few people can make a sink or stove on their own, and therefore they must be purchased separately. It is better to start choosing right away, since the dimensions of the same stove must match the rest of the work surfaces, otherwise it will look pretty ridiculous.

Required Tools

These tools will be needed not only for those who are going to do the whole room from start to finish on their own, but also for people who are annoyed by minor defects and other troubles. How to make repairs in the kitchen with your own hands? This question is much more common than the one above. But you will need quite different “helpers” here - from power tools this is a drill and a screwdriver, as well as a jigsaw (the latter is for those who will cut the purchased tree themselves). In addition, you will need a tape measure, a pencil, a building level and a square. A construction knife, a hacksaw for wood, as well as sandpaper. In addition, there are more important point screwdriver and wrenches- doors, as well as some other details, must be carefully screwed to the walls or floor.

How to make a corner kitchen with your own hands?

In fact, the action plan described above is also suitable for a corner kitchen. But they are more common than linear ones, simply because for small spaces this is the only way to build a comfortable and large work surface.

Differences begin exactly where you think - in the corner. It is this place that will have to be thought out more carefully than the rest, simply because if you make just a right angle, most working surface will be unavailable. So you have to go out and work on these places longer, making a smooth transition from one surface to another. In addition, the same should be done with hanging and floor cabinets.

Summer kitchen

Naturally, in the country it will be slightly different from its urban counterparts, but not so much that the work plan becomes completely different. So the usual country kitchen will be almost the same as the one in your apartment, and therefore you just need to follow the above plan. But the summer room is something completely different.

So how to make a kitchen in the country with your own hands? It is usually distinguished by the absence of walls, and also by the fact that it stands right in the courtyard, on the site. It is not hot there, and therefore this design is ideal in the period from late spring to mid-autumn. Naturally, both the construction and the layout will vary significantly.

The first difference here is the foundation. It must be strong enough to support the weight of not only the structure, but also all people. Sometimes this number can reach a dozen or even a dozen, which together has a significant weight. Therefore, the foundation is best made of stone. The building itself is built of wood - it is light and when processed protective compounds can withstand both weather and climatic conditions, and working features like heat and an abundance of moisture.

The walls, even if they are erected, do not cover the kitchen from all sides - usually from three. In addition, they are solid somewhere in the middle (this is done to cover the furniture), and then you can already equip a wooden grid or even use columns, leaving open space. A gable is usually laid on top light roof with appropriate additions in the form of drains for water and other things.

It is also easier with furniture here - there is no need to make places for storing utensils. So everything will consist of a work surface, a stove (often electric), a brazier that can be made removable, and also, in extravagant versions, an oven. In addition, if the summer room is large enough, then it can also serve as a gazebo and an external veranda.

For kids

How to make a children's kitchen with your own hands? In fact, it is difficult to realize the connection between real and children's cuisine. Nevertheless, it exists. Children develop, and therefore they have new interests. If you want to involve them in cooking in the future, then it would be wise to give them a children's kitchen. In addition, such a toy will occupy them for some time.

So, such kitchens are on sale, but with your own hands it is best to make them from an old chest of drawers or a large cabinet. The doors need to be removed. Everything else depends on your imagination and ingenuity.

For example, you can make something that looks like a smaller version of the kitchen. That is, we take as a fact the presence of a large chest of drawers. The doors have already been removed, and all the shelves have been taken out - you can get to work. You need to put one central shelf somewhere at a third of the height of the chest of drawers. The stove will be located on the right - you will need to make curly switches, similar burners, an oven door, and so on. On the left is the sink. Between them there is a surface where you can make a locker. All this is painted, decorated and brought to divine appearance. If you have a daughter and you are wondering how to make a kitchen for dolls with your own hands, then the same plan will do. Only in a smaller version, of course.

Hood

Well, in this matter, you need to understand that making a hood yourself is quite difficult - it requires certain special skills that most of us do not have today. Therefore, the option of installing a hood will be considered. This is not so easy - the main part is located above the stove, and it is she who works by pulling air. The air duct itself is usually made of corrugation in the form of a pipe. It is he who takes the air out into the street through the work done in outer wall ventilation.

If you are still concerned about the question of how to make a hood in the kitchen with your own hands, then you will need the same corrugated pipe and several fans. In addition, you will need to carefully cut the holes for the pipe, since everything must be airtight.

Ceiling

How to make a ceiling in the kitchen with your own hands? Before proceeding to work on it, it will take quite a long time to determine which type is best to choose. It's not easy because ideal option simply no. The problem here is that the humidity and temperature in the kitchen fluctuate over a fairly wide range. In addition, you also need to take into account how easy it will be to wash the ceiling - at least a few times the splashes will fly there as well. Yes, and you need a material that minimally absorbs odors.

The first option here is plaster. You can get by with a couple of working hands. You can wash the plaster quite often, it does not burn. True, during flooding, such a ceiling will not protect you at all: in best case these will be stains, and at worst - fallen off parts of the finish. Next comes the suspended ceiling. Here you need to remember that the wooden crate is not suitable. If you use a cassette design, then you can not be afraid of humidity and temperature. In addition, you can install comfortable lighting. There are also disadvantages - nothing will be washed from such a ceiling. But the undoubted plus here is the easy replacement, so the question of how to make repairs in the kitchen with your own hands will not arise at all. It will only be necessary to purchase a few panels and put the damaged ones in place. The last view - stretch ceiling. This is very a good option- they do not burn, but only melt, which increases fire safety. In addition, such ceilings will protect you from flooding - unless it is very large. At this point, the question of how to make a kitchen renovation with your own hands can be considered closed. The photos presented in the article will help you understand this issue.

Conclusion

In general, you should have already understood that making a kitchen on your own is real, even if it is not very simple. Questions that arise can be solved with the help of our article.

The most important thing when renovating a kitchen is careful planning. This allows you to avoid many problems and solve the question of how to make a kitchen with your own hands.